Dariush

Dear all. The problem can be solved by downgrading to u-boot v2015.10. However, in order to boot correctly, you should add "setenv bootm_boot_mode sec" to the boot.scr. Another problem is that in this image the OpenGLES2 is not OK! even mali driver does not load. Failed to open /dev/mali: No such file or directory Actually it needs lots of efforts to make everything OK! So i should switch to older 14.04 images. One interesting fact about this image is its beautiful Desktop. U-boot v2015.10.rar

Dear all. The problem can be solved by downgrading to u-boot v2015.10. However, in order to boot correctly, you should add "setenv bootm_boot_mode sec" the boot.scr.

Hi everybody. My cubieboard does not boot with Armbian 5.25. Does anyone know what is the problem? I really thank you beforehand. Actually i turns off after a second! Armbian_5.25_Cubieboard2_Ubuntu_xenial_default_3.4.113_desktop.7z U-Boot SPL 2017.01-armbian (Feb 02 2017 - 02:16:24) DRAM: 1024 MiB CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 Trying to boot from MMC1 U-Boot 2017.01-armbian (Feb 02 2017 - 02:16:24 +0100) Allwinner Technology CPU: Allwinner A20 (SUN7I) Model: Cubietech Cubieboard2 I2C: ready DRAM: 1 GiB MMC: SUNXI SD/MMC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial SCSI: SATA link 0 timeout. AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode flags: ncq stag pm led clo only pmp pio slum part ccc apst Net: eth0: ethernet@01c50000 Hit any key to stop autoboot: 0 6944 bytes read in 150 ms (44.9 KiB/s) switch to partitions #0, OK mmc0 is current device Scanning mmc 0:1... Found U-Boot script /boot/boot.scr 2652 bytes read in 185 ms (13.7 KiB/s) ## Executing script at 43100000 U-boot loaded from SD Boot script loaded from mmc 135 bytes read in 128 ms (1000 Bytes/s) 5072326 bytes read in 543 ms (8.9 MiB/s) 5607392 bytes read in 590 ms (9.1 MiB/s) ** File not found /boot/.next ** ** File not found .next ** 46320 bytes read in 313 ms (143.6 KiB/s) ## Loading init Ramdisk from Legacy Image at 43300000 ... Image Name: uInitrd Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 5072262 Bytes = 4.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... <6>Booting Linux on physical CPU 0 <6>Initializing cgroup subsys cpuset <6>Initializing cgroup subsys cpu <5>Linux version 3.4.113-sun7i (root@devel) (gcc version 5.4.0 20160609 (Ubuntu/ Linaro 5.4.0-6ubuntu1~16.04.4) ) #40 SMP PREEMPT Thu Feb 2 01:44:33 CET 2017 CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=10c5387d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: sun7i <6>Memory Reserved: <6> SYS : 0x43000000 - 0x4300ffff ( 64 kB) <6> VE : 0x44000000 - 0x48ffffff ( 80 MB) <6> G2D : 0x49000000 - 0x49ffffff ( 16 MB) <6> LCD : 0x4a000000 - 0x4bffffff ( 32 MB) Memory policy: ECC disabled, Data cache writealloc <6>sunxi: Allwinner A20 (AW1651/sun7i) detected. <7>On node 0 totalpages: 262144 <7>free_area_init_node: node 0, pgdat c0a89440, node_mem_map d0000000 <7> DMA zone: 512 pages used for memmap <7> DMA zone: 0 pages reserved <7> DMA zone: 65024 pages, LIFO batch:15 <7> Normal zone: 1008 pages used for memmap <7> Normal zone: 128016 pages, LIFO batch:31 <7> HighMem zone: 528 pages used for memmap <7> HighMem zone: 67056 pages, LIFO batch:15 <6>PERCPU: Embedded 8 pages/cpu @d0808000 s8256 r8192 d16320 u32768 <7>pcpu-alloc: s8256 r8192 d16320 u32768 alloc=8*4096<c> <7>pcpu-alloc: <c>[0] <c>0 <c>[0] <c>1 <c> Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096 <5>Kernel command line: root=UUID=b0a1043b-e74f-4a09-a990-69933508743c rootwait rootfstype=ext4 console=tty1 console=ttyS0,115200 cgroup_enable=memory swapaccou nt=1 hdmi.audio=EDID:0 disp.screen0_output_mode=1920x1080p60 panic=10 consolebla nk=0 enforcing=0 loglevel=1 ubootpart=3fc3b5a1-01 ubootsource=mmc <6>PID hash table entries: 4096 (order: 2, 16384 bytes) <6>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>allocated 2097152 bytes of page_cgroup <6>please try 'cgroup_disable=memory' option if you don't want memory cgroups <6>Memory: 1024MB = 1024MB total <5>Memory: 888648k/888648k available, 159928k reserved, 270336K highmem <5>Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) lowmem : 0xc0000000 - 0xef800000 ( 760 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc09e0ef4 (10084 kB) .init : 0xc09e1000 - 0xc0a19040 ( 225 kB) .data : 0xc0a1a000 - 0xc0a91d68 ( 480 kB) .bss : 0xc0a91d8c - 0xc0c66f78 (1877 kB) <6>SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>Preemptible hierarchical RCU implementation. <6> RCU dyntick-idle grace-period acceleration is enabled. <6> Additional per-CPU info printed with stalls. <6>NR_IRQS:192 <6>Architected local timer running at 24.00MHz. <6>sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms <2>start_kernel(): bug: interrupts were enabled early <6>Console: colour dummy device 80x30 <6>console [tty1] enabled <6>Calibrating delay loop... <c>1816.98 BogoMIPS (lpj=9084928) <6>pid_max: default: 32768 minimum: 301 <6>Mount-cache hash table entries: 512 <6>Initializing cgroup subsys cpuacct <6>Initializing cgroup subsys memory <6>Initializing cgroup subsys devices <6>Initializing cgroup subsys freezer <6>Initializing cgroup subsys blkio <6>Initializing cgroup subsys perf_event <6>CPU: Testing write buffer coherency: ok <6>CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>hw perfevents: enabled with ARMv7 Cortex-A7 PMU driver, 5 counters available <6>Setting up static identity map for 0x407255a8 - 0x40725600 CPU1: Booted secondary processor <6>CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>Brought up 2 CPUs <6>SMP: Total of 2 processors activated (3640.52 BogoMIPS). <6>devtmpfs: initialized <6>dummy: <6>NET: Registered protocol family 16 <6>DMA: preallocated 256 KiB pool for atomic coherent allocations <6>hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ccu-inf] aw clock manager init <6>[ccu-inf] aw_ccu_init <6>[ccu-inf] script config pll3 to 297MHz <6>[ccu-inf] script config pll4 to 300MHz <6>[ccu-inf] script config pll6 to 600MHz <6>[ccu-inf] script config pll7 to 297MHz <6>[ccu-inf] script config pll8 to 336MHz <6>Init eGon pin module V2.0 <6>bio: create slab <bio-0> at 0 <6>sunxi_gpio driver init ver 1.3 <6>gpiochip_add: registered GPIOs 1 to 2 on device: A1X_GPIO <5>SCSI subsystem initialized <7>libata version 3.00 loaded. <6>usbcore: registered new interface driver usbfs <6>usbcore: registered new interface driver hub <6>usbcore: registered new device driver usb <6>Linux media interface: v0.10 <6>Linux video capture interface: v2.00 <6>Advanced Linux Sound Architecture Driver Version 1.0.25. <6>Switching to clocksource arch_sys_counter <5>FS-Cache: Loaded <6>CacheFiles: Loaded <6>cfg80211: Calling CRDA to update world regulatory domain [usb_manager]: CONFIG_USB_SW_SUNXI_USB0_OTG [sw_hcd0]: usb host driver initialize........ [sw_hcd0]: open_usb_clock [sw_hcd0]: host_init_state = 1 [sw_hcd0]: platform is usb host [sw_hcd0]: sw_hcd_host0: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx (X), HB-ISO Tx (X), SoftConn) [sw_hcd0]: sw_hcd_init_controller: sw_hcd_host0: USB Host mode controller at f1c 13000 using PIO, IRQ 70 <6>sw_hcd_host0 sw_hcd_host0: sw_hcd host driver <6>sw_hcd_host0 sw_hcd_host0: new USB bus registered, assigned bus number 1 <6>hub 1-0:1.0: USB hub found <6>hub 1-0:1.0: 1 port detected wrn: hcd is not enable, need not start hcd [sw_hcd0]: sw_usb_host0_disable start -------sw_hcd0_soft_disconnect--------- is_on = 0, hcd0_set_vbus_cnt = 0 [sw_hcd_host0]: Set USB Power Off wrn: hcd is not enable, need not stop hcd [sw_hcd0]: close_usb_clock [sw_hcd0]: sw_usb_host0_disable end [sw_udc]: udc_init: version 20080411 <6>NET: Registered protocol family 2 <6>IP route cache hash table entries: 32768 (order: 5, 131072 bytes) <6>TCP established hash table entries: 131072 (order: 8, 1048576 bytes) <6>TCP bind hash table entries: 65536 (order: 7, 786432 bytes) <6>TCP: Hash tables configured (established 131072 bind 65536) <6>TCP: reno registered <6>UDP hash table entries: 512 (order: 2, 16384 bytes) <6>UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) <6>NET: Registered protocol family 1 <6>RPC: Registered named UNIX socket transport module. <6>RPC: Registered udp transport module. <6>RPC: Registered tcp transport module. <6>RPC: Registered tcp NFSv4.1 backchannel transport module. <6>Trying to unpack rootfs image as initramfs... <6>Freeing initrd memory: 4952K <6>audit: initializing netlink socket (disabled) <5>type=2000 audit(0.960:1): initialized highmem bounce pool size: 64 pages <5>VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>NFS: Registering the id_resolver key type <6>NTFS driver 2.1.30 [Flags: R/W]. <6>fuse init (API version 7.18) <6>JFS: nTxBlock = 6981, nTxLock = 55850 <6>SGI XFS with ACLs, security attributes, large block/inode numbers, no debug e nabled <6>Btrfs loaded <6>msgmni has been set to 1217 <6>alg: No test for stdrng (krng) <6>Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) <6>io scheduler noop registered <6>io scheduler deadline registered <6>io scheduler cfq registered (default) <6>sunxi disp driver loaded (/dev/disp api 1.0) <6>Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled <6>[uart]: used uart info.: 0x01 <6>[uart]: serial probe 0 irq 33 mapbase 0x01c28000 <6>sunxi-uart.0: ttyS0 at MMIO 0x1c28000 (irq = 33) is a U6_16550A <6>console [ttyS0] enabled <7>G2D: drv_g2d_init <6>G2D: g2dmem: g2d_start=49000000, g2d_size=1000000 <6>G2D: head:c9000000,tail:ca000000 <6>G2D: Module initialized.major:250 <6>brd: module loaded <6>loop: module loaded [NAND] nand driver version: 0x2 0x9 PHY_PageReadSpare : too much ecc err,bank 0 block 0,page 0 <4>Dev Sunxi softw311 nand magic does not match for MBR 1: softw411 <4>Dev Sunxi softw311 nand magic does not match for MBR 2: <4>Dev Sunxi softw311 nand magic does not match for MBR 3: <4>Dev Sunxi softw311 nand magic does not match for MBR 4: â–’â–’â–’ â–’â–’ <4>Dev Sunxi softw311 nand header bad for all MBR copies, MBR corrupted or not p resent. <4>Dev Sunxi softw411 nand: part 1, start 65536, size 65536 <4>Dev Sunxi softw411 nand: part 2, start 131072, size 7651328 <6> nand: nand1 nand2 [NAND]nand driver, ok. pwm-sunxi: pwm0 configured - period: 20, duty_percent: 50, duty: 10 <6>sw_ahci sw_ahci.0: controller can't do PMP, turning off CAP_PMP <6>ahci: SSS flag set, parallel bus scan disabled <6>sw_ahci sw_ahci.0: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform m ode <6>sw_ahci sw_ahci.0: flags: ncq sntf stag pm led clo only pio slum part ccc <6>scsi0 : sw_ahci_platform <6>ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88 <3>[spi-err] Get spi devices number failed <3>[spi-err] register spi devices board info failed <4>spi: cannot find any using configuration for all 4 spi co ntrollers, return directly! <6>bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) <6>Fixed MDIO Bus: probed <6>sunxi_emac Using mii phy on PortA <6>sunxi_emac Using MAC from SID: 02:85:07:c1:f4:72<4>emac_init fetch emac using configuration failed <6>gmac driver is disabled <6>PPP generic driver version 2.4.2 <6>PPP BSD Compression module registered <6>PPP Deflate Compression module registered <6>PPP MPPE Compression module registered <6>NET: Registered protocol family 24 <6>ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [sw-ehci1]: open clock [sw-ehci1]: Set USB Power ON <6>sw-ehci sw-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver <6>sw-ehci sw-ehci.1: new USB bus registered, assigned bus number 2 <6>sw-ehci sw-ehci.1: irq 71, io mem 0x01c14000 <6>sw-ehci sw-ehci.1: USB 2.0 started, EHCI 1.00 <6>hub 2-0:1.0: USB hub found <6>hub 2-0:1.0: 1 port detected [sw-ohci1]: open clock <6>sw-ohci sw-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver <6>sw-ohci sw-ohci.1: new USB bus registered, assigned bus number 3 <6>sw-ohci sw-ohci.1: irq 96, io mem 0x01c14400 <6>hub 3-0:1.0: USB hub found <6>hub 3-0:1.0: 1 port detected [sw-ehci2]: open clock [sw-ehci2]: Set USB Power ON <6>sw-ehci sw-ehci.2: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver <6>sw-ehci sw-ehci.2: new USB bus registered, assigned bus number 4 <6>sw-ehci sw-ehci.2: irq 72, io mem 0x01c1c000 <6>sw-ehci sw-ehci.2: USB 2.0 started, EHCI 1.00 <6>hub 4-0:1.0: USB hub found <6>hub 4-0:1.0: 1 port detected [sw-ohci2]: open clock <6>ata1: SATA link down (SStatus 0 SControl 300) <6>sw-ohci sw-ohci.2: SW USB2.0 'Open' Host Controller (OHCI) Driver <6>sw-ohci sw-ohci.2: new USB bus registered, assigned bus number 5 <6>sw-ohci sw-ohci.2: irq 97, io mem 0x01c1c400 <6>hub 5-0:1.0: USB hub found <6>hub 5-0:1.0: 1 port detected <6>Initializing USB Mass Storage driver... <6>usbcore: registered new interface driver usb-storage <6>USB Mass Storage support registered. <6>usbcore: registered new interface driver ums-alauda <6>usbcore: registered new interface driver ums-cypress <6>usbcore: registered new interface driver ums-datafab <6>usbcore: registered new interface driver ums_eneub6250 <6>usbcore: registered new interface driver ums-freecom <6>usbcore: registered new interface driver ums-isd200 <6>usbcore: registered new interface driver ums-jumpshot <6>usbcore: registered new interface driver ums-karma <6>usbcore: registered new interface driver ums-onetouch <6>usbcore: registered new interface driver ums-realtek <6>usbcore: registered new interface driver ums-sddr09 <6>usbcore: registered new interface driver ums-sddr55 <6>usbcore: registered new interface driver ums-usbat <6>mousedev: PS/2 mouse device common for all mice ===========================hv_keypad_init===================== ========HV Inital =================== <3>tkey_fetch_sysconfig_para: tkey_unused. hv_keypad_init: after fetch_sysconfig_para: normal_i2c: 0x0. normal_i2c[1]: 0x0 <3>sunxi-rtc sunxi-rtc: Error: Set LOSC to external failed. <3>sunxi-rtc sunxi-rtc: Warning: RTC time will be wrong! <6>sunxi-rtc sunxi-rtc: rtc core: registered rtc as rtc0 <6>i2c /dev entries driver config i2c gpio with gpio_config api <6>axp_mfd 0-0034: AXP (CHIP ID: 0x41) detected <6>axp_mfd 0-0034: AXP internal temperature monitoring enabled <4>i2c i2c-0: Invalid probe address 0x00 <6>I2C: i2c-0: AW16XX I2C adapter [cedar dev]: install start!!! [cedar dev]: install end!!! [tt]----- avs_dev driver load... ---- [tt]----- register iomem ---- [tt]--- avs_dev driver load ok!! ----- [ace_drv] start!!! [ace_drv] init end!!! [pa_drv] start!!! [pa_drv] init end!!! <6>axp20_ldo1: 1300 mV <6>axp20_ldo2: 1800 <--> 3300 mV at 3000 mV â–’