• Content Count

  • Joined

  • Last visited

 Content Type 


Member Map






Everything posted by g40

  1. Hi Martin I've been playing with the 2018.11 release of U-Boot. The problem with not finding USB devices on busses > 0 seems to have been fixed. Annoyingly the device tree has been completely revised so there is a deal of patching to be done. I also got u-boot network support enabled in 2018.05 with some device tree changes. I'll try and get patches out in due course. LMK if you'd like the changes. Thanks for all the help.
  2. You need to enable both the Sunxi CSI and the OV5647 drivers in the kernel configuration. Make them loadable modules ('M') in the kernel configuration..
  3. I'm trying to get TFTP support into U-Boot but it insists that 'no ethernet found'. I've added a couple of nodes to the device tree such that it has 'status = "okay" and mac-address = [00 00 00 00 00 00]; I've also added a top level alias in sun50i-h5-nanopi-k1-plus.dts (as added by @martinayotte following this thread) as below. Not sure if the U-Boot config needs changing in any way but the network components are certainly being built. Any thoughts most welcome. AATIA. aliases { serial0 = &uart0; ethernet0 = &emac; }; U-Boot dump of the loaded DTB on running system follows: => bdinfo arch_number = 0x00000000 boot_params = 0x40000100 DRAM bank = 0x00000000 -> start = 0x40000000 -> size = 0x80000000 baudrate = 115200 bps TLB addr = 0xBFFF0000 relocaddr = 0xBDF4B000 reloc off = 0x73F4B000 irq_sp = 0xB9F27590 sp start = 0xB9F27590 Early malloc usage: 2d8 / 400 fdt_blob = 00000000b9f275a8 => fdt addr 00000000b9f275a8 => fdt print ethernet0 ethernet@1c30000 { compatible = "allwinner,sun8i-h3-emac"; syscon = <0x0000000e>; reg = <0x01c30000 0x00010000>; interrupts = <0x00000000 0x00000052 0x00000004>; interrupt-names = "macirq"; resets = <0x00000005 0x0000000c>; reset-names = "stmmaceth"; clocks = <0x00000005 0x0000001b>; clock-names = "stmmaceth"; #address-cells = <0x00000001>; #size-cells = <0x00000000>; status = "okay"; mac-address = [00 00 00 00 00 00]; mdio { #address-cells = <0x00000001>; #size-cells = <0x00000000>; compatible = "snps,dwmac-mdio"; phandle = <0x0000000f>; }; mdio-mux { compatible = "allwinner,sun8i-h3-mdio-mux"; #address-cells = <0x00000001>; #size-cells = <0x00000000>; mdio-parent-bus = <0x0000000f>; mdio@1 { compatible = "allwinner,sun8i-h3-mdio-internal"; reg = <0x00000001>; #address-cells = <0x00000001>; #size-cells = <0x00000000>; ethernet-phy@1 { compatible = "ethernet-phy-ieee802.3-c22"; reg = <0x00000001>; clocks = <0x00000005 0x00000043>; resets = <0x00000005 0x00000027>; }; }; mdio@2 { reg = <0x00000002>; #address-cells = <0x00000001>; #size-cells = <0x00000000>; }; }; };
  4. Hi Zador, Thanks. Have you had any 64bit boards working with NFS?
  5. So this is failing for some odd reason. Armbian command line configuration is: /compile.sh BOARD=nanopik1plus BRANCH=next KERNEL_ONLY=no KERNEL_CONFIGURE=no RELEASE=jessie BUILD_DESKTOP=no ROOTFS_TYPE=fel FEL device mode is activated: @ubuntu-1804:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 005: ID 1f3a:efe8 Onda (unverified) V972 tablet in flashing mode Bus 002 Device 004: ID 0e0f:0008 VMware, Inc. Armbian interaction is then ... [ o.k. ] Calling image customization script [ customize-image.sh ] [ o.k. ] Starting FEL boot [ nanopik1plus ] [ o.k. ] Connect device in FEL mode and press [ <Enter> ] [ o.k. ] Loading files via [ FEL USB ] Failed to open input file: No such file or directory [ o.k. ] Press any key to boot again, <q> to finish [ FEL ] [ o.k. ] Connect device in FEL mode and press [ <Enter> ] [ o.k. ] Loading files via [ FEL USB ] Failed to open input file: No such file or directory [ o.k. ] Press any key to boot again, <q> to finish [ FEL ]
  6. Working from the documentation here: https://docs.armbian.com/Developer-Guide_FEL-boot/#what-is-felnfs-boot. Not much luck so far with an FA NanoPi K1 Plus. Please see below for details. TIA.
  7. Yes, is it ever I am going to try and repeat this exercise for the K1+ so it can boot out of SPI flash using TFTP. Are any of the other Allwinner based boards configured to do this? Thanks again for your help here.
  8. Hello Martin u-boot is detecting the OHCI/EHCI controllers. But it is only finding storage attached to USB0. In this case a USB=>SD card adapter. If I swap the thumb drive into USB0 and and SD adapter into USB2 or 4, it gets correctly identified. It's slightly annoying but definitely not a show-stopper. => usb reset resetting USB... EHCI failed to shut down host controller. EHCI failed to shut down host controller. USB0: USB EHCI 1.00 USB1: USB OHCI 1.0 USB2: USB EHCI 1.00 USB3: USB OHCI 1.0 USB4: USB EHCI 1.00 USB5: USB OHCI 1.0 scanning bus 0 for devices... 2 USB Device(s) found scanning bus 2 for devices... 1 USB Device(s) found scanning bus 4 for devices... 1 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found => usb storage Device 0: Vendor: Mass Rev: 1.00 Prod: Storage Device Type: Removable Hard Disk Capacity: 7580.0 MB = 7.4 GB (15523840 x 512) => usb storage Device 0: Vendor: SanDisk Rev: 1.00 Prod: Cruzer Blade Type: Removable Hard Disk Capacity: 7632.0 MB = 7.4 GB (15630336 x 512)
  9. Hello, What is the correct way to set armbianEnv.txt values when the distro is being built? Specifically I'd like to set kernel verbosity to a non-zero value? There does not seem to be a skeleton file so is all content generated dynamically? TIA
  10. Hi Martin. So, this is really good. I can now get the board to boot from the USB 1 connector on the K1 board (this is the single socket on the board pictured below). The actual USB device is in fact a USB=>SD card adapter, which is rather useful for comparison. One more question if I may. Does the DT control which USB interface is used? Repeating the exercise above with a card plugged into USB 2 or 3 does not work. `usb storage` does not detect any devices. *Many* thanks for your help here. FA NanoPi K1
  11. Hello Martin, Many thanks. Having tried both an update and a clean armbian build I get the same build failure. There is indeed no config in `build/cache/sources/u-boot/v2018.05/configs` Please let me know if you'd like to see any logs etc. Built build/sun50i_a64/debug/bl31.bin successfully [ o.k. ] Cleaning [ u-boot/v2018.05 ] [ o.k. ] Compiling u-boot [ 2018.05 ] [ o.k. ] Compiler version [ aarch64-linux-gnu-gcc 7.2.1 ] [ .... ] Checking out sources [ o.k. ] Cleaning [ u-boot/v2018.05 ] [ o.k. ] Started patching process for [ u-boot sunxi64-nanopik1plus-next ] [ o.k. ] Looking for user patches in [ userpatches/u-boot/u-boot-sunxi ] [ o.k. ] * [l][c] 0020-sunxi-call-fdt_fixup_ethernet-again-to-set-macaddr-f.patch [ o.k. ] * [l][c] 4kfix-limit-screen-to-full-hd.patch [ o.k. ] * [l][c] Merrii_Hummingbird_A20.patch [ o.k. ] * [l][c] add-a20-olinuxino-micro-emmc-support.patch [ o.k. ] * [l][c] add-a20-optional-eMMC.patch [ o.k. ] * [l][c] add-awsom-defconfig.patch [ o.k. ] * [l][c] add-bananapi-bpi-zero.patch [ o.k. ] * [l][c] add-beelink-x2.patch [ o.k. ] * [l][c] add-emmc_support_to_neo1_and_2.patch [ o.k. ] * [l][c] add-nanopi-air-emmc.patch [ o.k. ] * [l][c] add-nanopi-duo.patch [ o.k. ] * [l][c] add-nanopi-m1-plus2-emmc.patch [ o.k. ] * [l][c] add-nanopineoplus2.patch [ o.k. ] * [l][c] add-orangepi-plus2-emmc.patch [ o.k. ] * [l][c] add-orangepi-zero-usb-boot-support.patch [ o.k. ] * [l][c] add-orangepi-zeroplus.patch [ o.k. ] * [l][c] add-orangepi-zeroplus2_h3.patch [ o.k. ] * [l][c] add-sunvell-r69.patch [ o.k. ] * [l][c] add-tritium-series.patch [ o.k. ] * [l][c] add-xx-boot-auto-dt-select-neo2.patch [ warn ] * [l][c] add-xx-nanopi-k1-plus-emmc.patch [ failed ] [ o.k. ] * [l][c] add-xx-nanopineocore2.patch [ o.k. ] * [l][c] add_emmc_olinuxino_a64.patch [ o.k. ] * [l][c] add_emmc_orangepiwin.patch [ o.k. ] * [l][c] adjust-default-dram-clockspeeds.patch [ o.k. ] * [l][c] adjust-small-boards-cpufreq.patch [ o.k. ] * [l][c] enable-DT-overlays-support.patch [ o.k. ] * [l][c] enable-autoboot-keyed.patch [ o.k. ] * [l][c] enable-ethernet-orangepiprime.patch [ o.k. ] * [l][c] enable-r_pio-gpio-access-h3-h5.patch [ o.k. ] * [l][c] fdt-setprop-fix-unaligned-access.patch [ o.k. ] * [l][c] fix-usb1-vbus-opiwin.patch [ o.k. ] * [l][c] h3-Fix-PLL1-setup-to-never-use-dividers.patch [ o.k. ] * [l][c] h3-enable-power-led.patch [ o.k. ] * [l][c] h3-set-safe-axi_apb-clock-dividers.patch [ o.k. ] * [l][c] lower-default-DRAM-freq-A64-H5.patch [ o.k. ] * [l][c] sun8i-set-machid.patch [ o.k. ] * [l][c] sunxi-boot-splash.patch [ o.k. ] * [l][b] workaround-reboot-is-poweroff-olimex-a20.patch '/home/jevans/src/armbian-build/.tmp/atf-sunxi64-nanopik1plus-next/bl31.bin' -> './bl31.bin' HOSTCC scripts/basic/fixdep SHIPPED scripts/kconfig/zconf.tab.c SHIPPED scripts/kconfig/zconf.lex.c HOSTCC scripts/kconfig/conf.o SHIPPED scripts/kconfig/zconf.hash.c HOSTCC scripts/kconfig/zconf.tab.o HOSTLD scripts/kconfig/conf *** *** Can't find default configuration "arch/../configs/nanopi_k1_plus_defconfig"! *** scripts/kconfig/Makefile:119: recipe for target 'nanopi_k1_plus_defconfig' failed make[1]: *** [nanopi_k1_plus_defconfig] Error 1 Makefile:478: recipe for target 'nanopi_k1_plus_defconfig' failed make: *** [nanopi_k1_plus_defconfig] Error 2 sed: can't read .config: No such file or directory scripts/kconfig/conf --silentoldconfig Kconfig *** *** Configuration file ".config" not found! *** *** Please run some configurator (e.g. "make oldconfig" or *** "make menuconfig" or "make xconfig"). *** scripts/kconfig/Makefile:44: recipe for target 'silentoldconfig' failed make[2]: *** [silentoldconfig] Error 1 Makefile:478: recipe for target 'silentoldconfig' failed make[1]: *** [silentoldconfig] Error 2 make: *** No rule to make target 'include/config/auto.conf', needed by 'include/config/uboot.release'. Stop. [ error ] ERROR in function compile_uboot [ compilation.sh:175 ] [ error ] U-boot compilation failed [ o.k. ] Process terminated
  12. Hello Martin Let me paste better info then. Using master from armbian/build, UART spew below. How come no network or USB controllers? What else do I need to enable in the u-boot .config? Or is this because something is disabled in the DTB? TIA. U-Boot SPL 2018.05-armbian (Dec 29 2018 - 13:49:33 +0000) DRAM: 2048 MiB Trying to boot from sunxi SPI NOTICE: BL31: v2.0(debug):c876582 NOTICE: BL31: Built : 13:49:30, Dec 29 2018 NOTICE: BL31: Detected Allwinner H5 SoC (1718) NOTICE: BL31: Found U-Boot DTB at 0x407ecc8, model: FriendlyARM NanoPi K1 plus INFO: ARM GICv2 driver initialized INFO: Configuring SPC Controller NOTICE: BL31: PMIC: Defaulting to PortL GPIO according to H5 reference design. INFO: BL31: Platform setup done INFO: BL31: Initializing runtime services INFO: BL31: cortex_a53: CPU workaround for 855873 was applied INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0x4a000000 INFO: SPSR = 0x3c9 U-Boot 2018.05-armbian (Dec 29 2018 - 13:49:33 +0000) Allwinner Technology CPU: Allwinner H5 (SUN50I) Model: FriendlyARM NanoPi K1 plus DRAM: 2 GiB MMC: SUNXI SD/MMC: 0, SUNXI SD/MMC: 1 Loading Environment from EXT4... MMC: no card present ** Bad device mmc 0 ** Failed (-5) In: serial Out: serial Err: serial Net: No ethernet found. MMC: no card present ** Bad device mmc 0 ** MMC: no card present ** Bad device mmc 0 ** starting USB... No controllers found Autoboot in 1 seconds, press <Space> to stop
  13. Thank you Martin, I have u-boot getting to the media detection stage[1]. This is a FriendlyArm K1 (H5) with some externally attached SPI flash which is all working nicely. My problem seems to be getting USB support enabled in u-boot. Whatever .config options I have tried so far fail with section overflows and/or unresolved externals. [1] Trying to boot from sunxi SPI NOTICE: BL3-1: Running on H5 (1718) in SRAM A2 (@0x44000) NOTICE: Configuring SPC Controller NOTICE: BL3-1: v1.0(debug):0fc0ec6 NOTICE: BL3-1: Built : 14:33:21, Dec 8 2017 INFO: BL3-1: Initializing runtime services INFO: BL3-1: Preparing for EL3 exit to normal world INFO: BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9 U-Boot 2017.11-g80aa199f5a (Nov 28 2018 - 13:50:53 +0000) Allwinner Technology CPU: Allwinner H5 (SUN50I) Model: FriendlyElec NanoPi H5 DRAM: 2 GiB Sy8106a: 1200mv CPU Freq: 1008MHz MMC: SUNXI SD/MMC: 0, SUNXI SD/MMC: 1 MMC: no card present mmc_init: -123, time 2 *** Warning - MMC init failed, using default environment ERROR: unsupported boot mmc 3
  14. Hello, Does anyone have a u-boot .config file for SPI/USB boot on H5 boards? TIA.
  15. I think this is all out of date. I am running a 4.16 on FriendlyArm H3 and H5 boards which all have CSI enabled and working OV5640 hardware. These are the FA CAM500B models. A set of patches was posted to the V4L list some months back with a CSI driver and subsequent device tree mods. The CSI/OV drivers are enabled (and built-in) in the latest FA distros. Should be trivial to port to the Armbian set ups. FWIW my experience with the OPi camera was _terrible_. Apart from being limited to 2MP max, they never 'worked' at better than VGA and image quality was appalling. HTH.
  16. Greetings. The FriendlyArm docs imply that the parallel camera connection is the usual 24way FPC. Can anyone confirm this is the case? Is the imaging side of things supported in mainline (or near to it)? TVM
  17. Greetings. For anyone interested FriendlyArm have a Github repo which contains a working AW CSI driver. and has device tree files for NanoPi M1+ and Neo Air. See https://github.com/friendlyarm/linux.git. The branch is sunxi-4.16.y This is a work in progress but the setup is vastly simplified compared to the VFE subsystem in the 3.4/3.10 kernels. The OV5640 driver does produce video but I'm getting some odd images at the moment. Possibly colorspace related. As a bonus USB OTG is also working ... fa@FriendlyELEC:~/src$ v4l2-compliance Driver Info: Driver name : sun6i-video Card type : sun6i-csi Bus i[59399.088082] sun6i-csi 1cb0000.camera: ================= START STATUS ================= nfo : platform:camera Driver version: 4.16.0 Capabiliti[59399.102740] sun6i-csi 1cb0000.camera: ================== END STATUS ================== es : 0x84200001 Video Capture Streaming Extended Pix Format Device Capabilities Device Caps : 0x04200001 Video Capture Streaming Extended Pix Format Compliance test for device /dev/video0 (not using libv4l2): Required ioctls: test VIDIOC_QUERYCAP: OK Allow for multiple opens: test second video open: OK test VIDIOC_QUERYCAP: OK test VIDIOC_G/S_PRIORITY: OK Debug ioctls: test VIDIOC_DBG_G/S_REGISTER: OK (Not Supported) test VIDIOC_LOG_STATUS: OK Input ioctls: test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported) test VIDIOC_G/S_FREQUENCY: OK (Not Supported) test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported) test VIDIOC_ENUMAUDIO: OK (Not Supported) test VIDIOC_G/S/ENUMINPUT: OK test VIDIOC_G/S_AUDIO: OK (Not Supported) Inputs: 1 Audio Inputs: 0 Tuners: 0 Output ioctls: test VIDIOC_G/S_MODULATOR: OK (Not Supported) test VIDIOC_G/S_FREQUENCY: OK (Not Supported) test VIDIOC_ENUMAUDOUT: OK (Not Supported) test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported) test VIDIOC_G/S_AUDOUT: OK (Not Supported) Outputs: 0 Audio Outputs: 0 Modulators: 0 Input/Output configuration ioctls: test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported) test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported) test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported) test VIDIOC_G/S_EDID: OK (Not Supported) Test input 0: Control ioctls: test VIDIOC_QUERYCTRL/MENU: OK test VIDIOC_G/S_CTRL: OK test VIDIOC_G/S/TRY_EXT_CTRLS: OK test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: OK test VIDIOC_G/S_JPEGCOMP: OK (Not Supported) Standard Controls: 14 Private Controls: 0 Format ioctls: fail: v4l2-test-formats.cpp(259): duplicate format 32314d48 test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: FAIL test VIDIOC_G/S_PARM: OK (Not Supported) test VIDIOC_G_FBUF: OK (Not Supported) fail: v4l2-test-formats.cpp(314): !colorspace fail: v4l2-test-formats.cpp(417): testColorspace(pix.pixelformat, pix.colorspace) test VIDIOC_G_FMT: FAIL test VIDIOC_TRY_FMT: OK (Not Supported) test VIDIOC_S_FMT: OK (Not Supported) test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported) Codec ioctls: test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported) test VIDIOC_G_ENC_INDEX: OK (Not Supported) test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported) Buffer ioctls: test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK fail: v4l2-test-buffers.cpp(500): q.has_expbuf(node) test VIDIOC_EXPBUF: FAIL Total: 38, Succeeded: 35, Failed: 3, Warnings: 0
  18. Hi Thorsten, No. It was simpler and more productive to use the NanoPi Neo Air and M1 boards. The FA CAM500B module works pretty well with the patch included in the legacy Armbian build. BR Jerry
  19. to reduce the noise level? For example I created a topic this afternoon that is irrelevant at best, misleading at worst and solves no problems for anyone. It would be best if it never got into the Google cache. But, failing that, can
  20. Hello Thomas. This is not a systemic Armbian problem, just a local issue.
  21. Hello Igor and thanks. I will check that out.
  22. Using Armbian 5.33. What am I missing? I know the hardware is good as I've had this working before. The modules listed in /etc/modules include hci_uart which is missing. When and how is this built? It does not appear in the 3.4.113 kernel menuconfig options TAIA Jerry $ uname -a Linux nanopiair 3.4.113-sun8i #22 SMP PREEMPT Mon Sep 25 13:11:21 BST 2017 armv7l GNU/Linux # this did work! $sudo nmcli r wifi on $sudo nmcli dev wifi # lists available WAP's $sudo nmcli dev wifi connect <WAP name> password <your password here>
  23. @perfstr Good to know you had this working. By any chance do you still have the .config? My Windows host gets as far as installing the driver then fails trying to get a device descriptor. Device side (H3 powered NanoPi Air) reports below TAIA ``` @nanopiair:/test/gadget_usb$ sudo gadget_usb -v /dev/gadget/sunxi_usb_udc ep0 configured serial="mjqebex15vip4cq2dptcpzak8f508n36z1ulgiqmwe5lgfborb0a5sj4x4xb40a" ** Mon Sep 18 14:01:55 2017 CONNECT high speed SETUP 80.06 v03ee i0000 18 ... protocol stall 80.06 SETUP 80.06 v0303 i0409 255 SETUP 80.06 v0300 i0000 255 SETUP 80.06 v0300 i0000 257 read 2 ep0 events DISCONNECT SUSPEND CONNECT high speed read 2 ep0 events DISCONNECT SUSPEND ```