[ArduinoIDE on Armbian for Udoo]

Replace bossac from /usr/local/lib/udoo-arduino-cli/hardware/tools to

https://github.com/UDOOboard/bossac/tree/master/prebuilt/udoo

[UDOO uart enable]

Install.log : http://pastebin.com/yhHcpXsk

[UDOO uart enable]

System ubuntu 14.04 on virtual machine. Today i compiled new image udoo ubuntu trusty 3.14.28 but not boot on my udoo quad.

U-Boot SPL 2015.10-armbian (Jan 02 2016 - 11:41:27)


U-Boot 2015.10-armbian (Jan 02 2016 - 11:41:27 +0100)

CPU:   Freescale i.MX6Q rev1.2 at 792 MHz
Reset cause: POR
Board: UDOO Quad
DRAM:  1 GiB
MMC:   FSL_SDHC: 0
*** Warning - bad CRC, using default environment

No panel detected: default to HDMI
Display: HDMI (1024x768)
In:    serial
Out:   serial
Err:   serial
Net:   using phy at 6
FEC [PRIME]
Hit any key to stop autoboot:  0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc
Found U-Boot script /boot.scr
** File not found /boot.scr **
** Unrecognized filesystem type **
Found U-Boot script /boot/boot.scr
590 bytes read in 160 ms (2.9 KiB/s)
Running bootscript from mmc ...
## Executing script at 12000000
** File not found /boot/dtb/imx6q-udoo-hdmi.dtb **
** Unrecognized filesystem type **
6681024 bytes read in 483 ms (13.2 MiB/s)
Kernel image @ 0x12000000 [ 0x000000 - 0x65f1c0 ]
ERROR: Did not find a cmdline Flattened Device Tree
Could not find a valid device tree
Device Tree: dts/imx6q-udoo-hdmi.dtb
** Unrecognized filesystem type **
Booting from net ...
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
DHCP client bound to address 192.168.0.101 (3016 ms)
Using FEC device
TFTP from server 0.0.0.0; our IP address is 192.168.0.101; sending through gateway 192.168.0.1
Filename 'zImage'.
Load address: 0x12000000
Loading: T T T T T T T T T T
Retry count exceeded; starting again
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
DHCP client bound to address 192.168.0.101 (3015 ms)
Using FEC device
TFTP from server 0.0.0.0; our IP address is 192.168.0.101; sending through gateway 192.168.0.1
Filename 'dts/imx6q-udoo-hdmi.dtb'.
Load address: 0x18000000
Loading: T T T T T T T T T T
Retry count exceeded; starting again
Bad Linux ARM zImage magic!

[UDOO uart enable]

I'm trying create new image, but for end i have error in install.log:

Fingerprinting. Armbian 4.81 Udoo Debian jessie next Linux 4.2.8 info
Displaying message: Building deb package. linux-jessie-root-next-udoo_4.81_armhf.deb info
Displaying message: Install locales en_US.UTF-8 info
chroot: failed to run command ‘/bin/bash’: No such file or directory
Displaying message: Installation of package failed  err

In install.log from archives:

Displaying message: Compiling uboot. Please wait. 2015.10 info
31.12.2015 17:17:23 /home/marcin/sources/u-boot-udoo/2015.10.fslc-qdl/udoo_qdl_config
Displaying message: Target directory /home/marcin/output/debs/ info
Displaying message: Building deb linux-u-boot-next-udoo_4.81_armhf.deb info
Displaying message: Building failed, check configuration. linux-u-boot-next-udoo_4.81_armhf.deb deleted err
 

[UDOO uart enable]

I'm new, I need to modify the kernel under udoo before compiling, at which point I do that?

[UDOO uart enable]

Where are config files in source kernel with function to enable next uart port in udoo?