Vladimir Petrovic

Thanks man. I did not saw that. All work no play makes jack a dull boy. Tnx again. Послато са Redmi Note 6 Pro уз помоћ Тапатока

Nothing in dmesg. Had to see.u-boot. When I get that log I will post. Thou I got segmentation fault on dpkg and when I replaced bin fom a pckage it started working again. Could be sdcard? Послато са Redmi Note 6 Pro уз помоћ Тапатока

verbosity=1 logo=enabled console=both disp_mode=1920x1080p60 overlay_prefix=sun8i-h3 rootdev=UUID=f2be4c3e-fb7c-4a81-b3db-f29ff41e7bdf rootfstype=ext4 overlays=analog-codec cir i2c0 i2c1 i2c2 pps-gpio pwm spdif-out spi-spidev uart1 uart2 uart3 usbhost0 usbhost1 usbhost2 usbhost3 w1-gpio param_spi_dev_bus=0 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u Послато са Redmi Note 6 Pro уз помоћ Тапатока

Orange pi one refuse to add spi to /dev/. It's 5.73 armbian kernel 4.19.20-sunxi. I've activated spi dev from armbian-config but no device after reboot. Gpio and i2c work great . Anyone had problem like this? Послато са Redmi Note 6 Pro уз помоћ Тапатока

can you suggest any android image for testing if camera module is not fried? Also i figured out that twi addres does not want to change in bin file made from edited fex. When I write 0x78 in fex it compile to 120 (done bin2fex again on bin file I've created from modified fex)

Hi, Sorry for bringing this topic from dead but I have some problems with ov5640. I bought this camera module : https://www.aliexpress.com/item/OPI-5MP-Camera-OV5640-Auto-zoom-with-wide-angle-lens-for-Orange-Pi-PC-Pi-One/32869355445.html?spm=a2g0s.9042311.0.0.2ac84c4d4jeaqv and I connected it to Orange Pi One. I've isntalled lts 16 image with kernel 3.4.113 and I've loaded ov5640 kernel and vfe_v4l2 modules. I dont get /dev/video0 device and have this otput from kernel.log: [OV5640@lex]init_sensor - frame_rate: 0, max_win_size: 11 [ISP] isp platform_id = 5! [OV5640@lex]CSI_SUBDEV_PWR_ON! [OV5640@lex]sensor_init 0x0 [OV5640@lex]sensor read retry=2 [OV5640@lex]error at sensor_detect [OV5640@lex]chip found is not an target chip. [OV5640@lex]CSI_SUBDEV_PWR_OFF! what could be wrong? Do I have to swap R6 and r5 on this board?

look's like u-boot does not recognise usb2sata controler on NAS expansion board for opi0. Any idea how to correct this? Is it even possible?

So legacy is a choice? Can I get ov5640 work in legacy ubuntu on opi one?

Can somebody confirm that this driver work on mainline opi0 kernel? https://github.com/avafinger/ov5640

So it's usb sata... I think I know what I missed in instalation. I've dd if=soruce of=/dev/sdxx but I've did not set boot flag on partiton so that's why it does not boot from the hdd. I'll check today if I can boot it bringing boot flag to hdd. I have UART deug console attached to RPI0 . Tnx.

I've found this: https://github.com/lentinj/u-boot/blob/master/doc/README.sata . Look's like it's possible. Anyone correct me if I'm wrong.

Is it possible to boot Orange pi Zero directly from hdd. I have sata hdd attached to OPI Zero via PI NAS. I can boot from usb flash and use HDD as root device but faild to boot from HDD directly. Is it possible to do this or not.

Ok. Tnx. Job Done.

so I can push bin like this to spi flash: flashcp /usr/lib/linux-u-boot-next-orangepizero_5.38_armhf/u-boot-sunxi-with-spl.bin /dev/mtd0 ?