Jump to content

Efforts to develop firmware for H96 MAX V56 RK3566 8G/64G

Hqnicolas

By Hqnicolas
in Rockchip CPU Boxes

 Share

Recommended Posts

mvpwar

mvpwar

Posted
Posted (edited)
3 minutes ago, hotnikq said:

please get the DEV Partition from image v5 from the flashed device!!!!
i have changed it 

the partition table now as below, I had change the root partition to 0x00010800 refer to unpacked v4 image @hotnikq

image.png.ccea4ae116e8d882d6ad56c1d1ae2fa3.png

 

 

Edited by mvpwar
0
Hqnicolas

Hqnicolas

Posted
  • Author
Posted (edited)

image.png

 

OK the V5 image address is 0x00010800
you will need to flash the root.img in this address 
please change it on the table 

Edited by hotnikq
0
mvpwar

mvpwar

Posted
Posted
1 minute ago, hotnikq said:

LOL! did you fix it?
I'm at work now, can you recompile and test?

 

NO, the kernel can not be loaded, though I change the partition ,the same result 

0
mvpwar

mvpwar

Posted
Posted
Just now, hotnikq said:

OK the V5 image address is 0x00010800
you will need to flash the root.img in this address 
please change it on the table 

Not useful, I had tried many times @hotnikq

0
Kenneth Hidalgo

Kenneth Hidalgo

Posted
Posted

I asked the seller that the device (h96 max v56 4gb/32gb) had some version of Linux and he sent me that useless image, I made many changes to make it work but I still need to fix the size of the Root partition (6gb)

0
mvpwar

mvpwar

Posted
Posted
1 minute ago, Kenneth Hidalgo said:

but I still need to fix the size of the Root partition (6gb)

 

the root partition enlarge is very easy,  just enlarge the rootfs partition (change the parameter.txt, like root:grow), and resize2fs root block @Kenneth Hidalgo

0
mvpwar

mvpwar

Posted
Posted (edited)
1 hour ago, hotnikq said:

Balena etcher

 

when I selected the v5 update.img , the Balena etcher alert the image has no partition table , and I still flashed to the U stick, and boot fail thought the u-boot foud the usb device

@hotnikq debug message as below

  

U-Boot 2017.09-g32ed8ff-210328-dirty #pc (Apr 21 2021 - 20:51:20 +0800)

Model: Rockchip RK3568 Evaluation Board
PreSerial: 2, raw, 0xfe660000
DRAM:  7.7 GiB
Sysmem: init
Relocation Offset: ed39f000, fdt: eb9f8e18 
Using default environment

Hotkey: ctrl+`
dwmmc@fe2b0000: 1, dwmmc@fe2c0000: 2, sdhci@fe310000: 0
Bootdev(atags): mmc 0
MMC0: HS200, 200Mhz
PartType: EFI
boot mode: None
FIT: No fdt blob
No resource partition
No resource partition
Failed to load DTB
Failed to get kernel dtb, ret=-19
io-domain: OK
Model: Rockchip RK3568 Evaluation Board
rockchip_set_serialno: could not find efuse/otp device
CLK: (sync kernel. arm: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
  apll 816000 KHz
  dpll 390000 KHz
  gpll 1188000 KHz
  cpll 1000000 KHz
  npll 24000 KHz
  vpll 24000 KHz
  hpll 24000 KHz
  ppll 100000 KHz
  armclk 816000 KHz
  aclk_bus 150000 KHz
  pclk_bus 50000 KHz
  aclk_top_high 300000 KHz
  aclk_top_low 200000 KHz
  hclk_top 150000 KHz
  pclk_top 50000 KHz
  aclk_perimid 300000 KHz
  hclk_perimid 150000 KHz
  pclk_pmu 50000 KHz
Net:   No ethernet found.
Hit key to stop autoboot('CTRL+C'):  0 
## Booting FIT Image FIT: No fit blob
FIT: No FIT image
ANDROID: reboot reason: "(none)"
optee api revision: 2.0
TEEC: Waring: Could not find security partition
Not AVB images, AVB skip
No valid android hdr
Android image load failed
Android boot failed, error -1.
MMC error: The cmd index is 1, ret is -110
Card did not respond to voltage select!
mmc_init: -95, time 10
switch to partitions #0, OK
mmc0(part 0) is current device
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
starting USB...
Bus dwc3@fcc00000: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus dwc3@fd000000: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus dwc3@fcc00000 for devices... 1 USB Device(s) found
scanning bus dwc3@fd000000 for devices... cannot reset port 1!?
1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found

Device 0: unknown device
No ethernet found.
missing environment variable: pxeuuid
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/00000000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/0000000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/000000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/00000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/0000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/00
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/0
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/default-arm-rockchip
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/default-arm
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/default
No ethernet found.
Config file not found
No ethernet found.
No ethernet found.

 

Edited by mvpwar
1
Hqnicolas

Hqnicolas

Posted
  • Author
Posted (edited)
7 hours ago, mvpwar said:

the Balena etcher alert the image has no partition

Sorry @mvpwar

When I said v5 image

It's about the v0.5 flash drive image that I have done...

I'm not so good with instructions,

For me It's hard to give instructions over a forum topic, be better when I have the device to debug.

 

Flash the V5 update.IMG on device

And v0.5 SD image on flash drive over USB 3.0

Edited by hotnikq
0
mvpwar

mvpwar

Posted
Posted
58 minutes ago, hotnikq said:

Flash the V5 update.IMG on device

And v0.5 SD image on flash drive over USB 3.0

 

I had found the problem, and I tried to flashing the other image rock3a_debian_buster_xfce4_arm64_20211113_0127-gpt.img, no work

Now I flashed your v0.5 SD image ,the same result @hotnikq

  

U-Boot 2017.09-g32ed8ff-210328-dirty #pc (Apr 21 2021 - 20:51:20 +0800)

Model: Rockchip RK3568 Evaluation Board
PreSerial: 2, raw, 0xfe660000
DRAM:  7.7 GiB
Sysmem: init
Relocation Offset: ed39f000, fdt: eb9f8e18 
Using default environment

Hotkey: ctrl+`
dwmmc@fe2b0000: 1, dwmmc@fe2c0000: 2, sdhci@fe310000: 0
Bootdev(atags): mmc 0
MMC0: HS200, 200Mhz
PartType: EFI
boot mode: None
FIT: No fdt blob
No resource partition
No resource partition
Failed to load DTB
Failed to get kernel dtb, ret=-19
io-domain: OK
Model: Rockchip RK3568 Evaluation Board
rockchip_set_serialno: could not find efuse/otp device
CLK: (sync kernel. arm: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
  apll 816000 KHz
  dpll 390000 KHz
  gpll 1188000 KHz
  cpll 1000000 KHz
  npll 24000 KHz
  vpll 24000 KHz
  hpll 24000 KHz
  ppll 100000 KHz
  armclk 816000 KHz
  aclk_bus 150000 KHz
  pclk_bus 50000 KHz
  aclk_top_high 300000 KHz
  aclk_top_low 200000 KHz
  hclk_top 150000 KHz
  pclk_top 50000 KHz
  aclk_perimid 300000 KHz
  hclk_perimid 150000 KHz
  pclk_pmu 50000 KHz
Net:   No ethernet found.
Hit key to stop autoboot('CTRL+C'):  0 
## Booting FIT Image FIT: No fit blob
FIT: No FIT image
ANDROID: reboot reason: "(none)"
optee api revision: 2.0
TEEC: Waring: Could not find security partition
Not AVB images, AVB skip
No valid android hdr
Android image load failed
Android boot failed, error -1.
MMC error: The cmd index is 1, ret is -110
Card did not respond to voltage select!
mmc_init: -95, time 10
switch to partitions #0, OK
mmc0(part 0) is current device
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
starting USB...
Bus dwc3@fcc00000: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus dwc3@fd000000: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus dwc3@fcc00000 for devices... 1 USB Device(s) found
scanning bus dwc3@fd000000 for devices... cannot reset port 1!?
1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found

Device 0: unknown device
No ethernet found.
missing environment variable: pxeuuid
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/00000000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/0000000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/000000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/00000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/0000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/00
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/0
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/default-arm-rockchip
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/default-arm
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/default
No ethernet found.
Config file not found
No ethernet found.
No ethernet found.

 

0
mvpwar

mvpwar

Posted
Posted

do you know how to type some command on ttl debug serial mode? I want to check mmc info, but I found the keyboard input can't interupt the u-boot booting, my box only connect the tx,rx,gnd, I remember it works when I ttl debug the orangepi3 

0
Hqnicolas

Hqnicolas

Posted
  • Author
Posted
1 hour ago, mvpwar said:

do you know how to type some command on ttl debug serial mode?

 

You need to enable console tty over dtb command line

So it will wait for interaction

 

Since we use an original Android dtb on uboot.img

No console enabled 😅

0
Hqnicolas

Hqnicolas

Posted
  • Author
Posted (edited)
3 hours ago, mvpwar said:

rock3a_debian_buster_xfce4_arm64_20211113_0127-gpt.img, no work

😮‍💨

I'm about to buy an 8gb box just to make this image, but I already have a lot of hardware sitting here, including a radxa rock 3A 8gb ram 64gb mmc 1tb nvme, that don't accelerate GPU 😂 (drivers), hardware waiting for some use, tomorrow I'm going to make a socks5 Proxy over isolated docker L3 lan on it just to prevent it from being at the bottom of the drawer

Edited by hotnikq
0
mvpwar

mvpwar

Posted
Posted (edited)

 

1 hour ago, hotnikq said:

So it will wait for interaction

 

No need this interaction, I found I can not type the username and password while the debian10 init finished (this is interaction), I feel that I can't send any data to the ttl terminal 

can you login the os at serial console when the os Initialization completed @hotnikq

Edited by mvpwar
0
mvpwar

mvpwar

Posted
Posted (edited)
26 minutes ago, hotnikq said:

Can you use the linaro build image to boot from USB? On 8gb device?

can boot from mmc...no need usb

I hadn't even boot kernel6.2, I don't know why you can boot the os without boot.img, it is so difficult @hotnikq

Edited by mvpwar
0

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
 Share
Go to topic listing
×
×
  • Create New...

Important Information

Terms of Use - Privacy Policy - Guidelines

  I accept