kernel: ... sysrq: HELP messages in log

[loeriver]

From time to time I see a message like this in my log files:

 

2025-06-05T11:29:33.367636+02:00 bananapipro2 kernel: [934985.549250] sysrq: HELP : loglevel(0-9) reboot(b) crash(c) terminate-all-tasks(e) memory-full-oom-kill(f) kill-all-tasks(i) thaw-filesystems(j) sak(k) show-backtrace-all-active-cpus(l) show-memory-usage(m) nice-all-RT-tasks(n) poweroff(o) show-registers(p) show-all-timers(q) unraw(r) sync(s) show-task-states(t) unmount(u) show-blocked-tasks(w) dump-ftrace-buffer(z) replay-kernel-logs(R)

 

The system continues to work (although I remember that it stooped at this point in older releases).

 

Is there any action required? I am afraid that this could stop my system which is running unattended for longer periods usually.

 

I am running v25.2.2 for Banana Pi Pro running Armbian Linux 6.12.20-current-sunxi.

[IBV]

Hi,

 

it looks like you or a process is triggering the SysRq key.

For example, If I press Alt + PrtSc (SysRq) + h, I see the same message in dmesg.

 

https://en.wikipedia.org/wiki/Magic_SysRq_key

 

[djurny]

Hi @loeriver,

Check your serial console, as sending a serial <BRK> will trigger the Magic Sysrq sequence.

For example, using `tio` to connect to a serial console, I can invoke the Magic Sysrq help test with <ctrl>-t + B + <enter>.

Perhaps your serial port has it's RX line shorted to ground?

Groetjes,

[loeriver]

Hi,

thank you for your comments, at least I learned about the SysRq sequence this way.

 

I actually have no clue which process should send this sequence, an hardware issue of the RX line seems also unlikely to me (very short wire to the RS232-USB converter).

 

The only additional observations:

 

-it is a rare event, 24x7 system, most recent events:

• Jun 9th: at the end of a shutdown sequence
• Jun, 5th: no obviously related entries in syslog before it
• May, 28th: no obviously related entries in syslog before it
• May, 24th: at the end of a shutdown sequence
• May, 23rd: at the end of a shutdown sequence
• May 22nd: at the end of a shutdown sequence

-it always occurs in pairs, timestamps separated by some µs, e.g. 16:50:49.191219 and 16:50:49.191355

 

Meanwhile on v25.5.1 for Banana Pi Pro running Armbian Linux 6.12.30-current-sunxi.

 

I guess I will have to live with this effect, which is not harmful as long as the system continues to run.

 

Greetings.

[IBV]

You could try to install auditd and check what it says when the event appears. Maybe it will tell you which process is sending the event:

$ sudo apt install auditd
$ sudo auditctl -w /proc/sysrq-trigger -p w -k sysrq_watch

The second command is creating a watch on sysrq-trigger for write events, called sysrq_watch.

You can query check this watch with:

$ sudo ausearch -k sysrq_watch

See what you can find when you detect another trigger of the sysrq key.

[loeriver]

Thank you for this very helpful hint. I have installed auditd, I thought I have to systemctl (start, enable) auditd also to have it watching: but this seems to have been done by the install cmd already, as it is running.

 

As I saw a burst of  7225 (!) sysrq messages in the log for 2025-06-18, between 08:55 and 09:50 again I am rather nervous about this topic. Since then no new messages again. Mysterious ...

 

Greetings.

[djurny]

Hi Loeriver,

Where is the other end of your USB serial dongle connected to? Can you check there if the dongle had disappeard from the USB bus and re-appeared around the same time?

In my "professional" life we have had workstations mysteriously reboot whenever we would power cycle the device hosting the USB to serial device.

Even though you say it's not related, if this is still mysterious, best to check under each stone...

Groetjes,