Jump to content

IcerJo

Members
  • Posts

    22
  • Joined

Everything posted by IcerJo

  1. Mind if I ask which kernel are you using? and did you experience any problems adding any addon's? I had no problems with a fresh install of Bullseye on my Helios4 but had issues when I tried adding snapraid and mergerfs on my Helios64 with the stock Bullseye Kernel. Also Experiencing a freeze/issue When installing OMV through armbian-config where it freezes at the end while processing triggers for man-db
  2. I'm using Armbian Debian, if you are using Armbian are you able to use the max clock speeds of the 2 big cores? Sent from my Pixel 4a (5G) using Tapatalk
  3. I have my CPU set to scale from the lowest number and 1.4 for the high-end, and performance set to on demand and have no problems, anything above 1.4 and it crashes within days. Sent from my Pixel 4a (5G) using Tapatalk
  4. Thank you @Igor, my apologies and thank you for all you and the team do. I plan to donate to Armbian when some of my remodeling projects are done. and That would be swell @Heisath, I did see in the FAQ's that we may not be "supported" Officially but we are in a Community type of support, so if you were able to acquire and run Edge/Nightly that would definitely help out in the long run
  5. I wonder if someone could buy it and donate it to Armbian for testing so that we could be Supported again? If anyone does buy and donate I will donate to them
  6. I see you updated your Device, there is a known issue with the kernel in question, there is another thread that details how you can revert back to the old .43 kernel to regain access. If you look the following post/instructions you should be good to go. I'm curious as to why no one referred you to that post. I know the title of the Thread is about upgrading to Bullseye but it also got sidetracked to troubleshooting Armbian 21.08.1 and the EMMC read only error/problem.
  7. Just after 24hours system randomly rebooted while i was out of the house, so back to the old trick of setting the max to 1.4ghz and min to 408mhz
  8. I opted to just setup an SD Card with the latest, and redo my OMV install on it, since that's technically all I use it for at this time, I was able to get the old system booted with no problems by pushing re-pushing the bootloader but wasn't able to install the Deb files, and I am not that confident in my linux skill set, though i learned a few new tips and tricks during the troubleshooting! I'll repush to EMMC once issues have eventually been resolved, or i may downgrade the kernel and push, i'll see later. Thank you @ebin-dev for your advice and assistance and thank you @TDCroPower for the RSync article!
  9. Thank you for the Rsync guide, I'm going to give this a try real quick, I had to modify the parameters since i had my usb SD card reader mounted as /media/USB, the rsync just finished. I'm going to shutdown, and pop the SD Card in and see what happens
  10. If you can SSH in or possibly boot off of an SD card with the latest image, you can reinstall the bootloader, it at least gets it up and running, least for me that means I can get in and see my drives and wrote to the, but I fear the emmc is still somewhat locked down but yet it lete turn ash back on. Sent from my Pixel 4a (5G) using Tapatalk
  11. Seems like it doesn't make it fully writeable, but it does let the system boot and I'm able to access all of my files and save some changes in the system, like turn some services on and off. But I couldnt write the 3 files to the emmc to do a downgrade so unless I messed up I am at a loss but would gladly try the above mentioned. Sent from my Pixel 4a (5G) using Tapatalk
  12. In Essence I did what you stated but by using armbian-config to re-push the bootloader. How would one go about making the emmc Write-able in order to install the 3 packages to downgrade the kernel? Or would I need to re-setup OpenMediavault and everything, and run it from the SDcard or copy it over to the emmc from the SD Card with the old kernel, and then do a kernel freeze for time being till issue is resolved?
  13. Ahh, so it's essentially a ticking time bomb? I pushed the bootloader from an SD card and got my system back up yesterday.
  14. I don't know much when it comes to armbian, but from the temp fix I did, it seems like the bootloader was the culprit/issue, I installed/pushed a new bootloader via the latest image on an sd card and my system is back up and running with the latest kernel with no problems. Or rather i think it might be a combination of issues, I am not sure how the bootloader being pushed would work if the kernel is the culprit but at least my system is back up and stable till they have a proper fix implemented. I read another Post where its a Kernel Panic that Occurs at 150372 seconds = 41.7 hours..
  15. Thanks, I guess I'll stick with what works/caused me to be stable for this long [emoji16] Edit: I opted to start fresh and am testing the stability of the new kernel's Govenor and cpu frequencies via SD Card till they fix the EMMC issue's which then at that time i will push Armbian back to the EMMC. So far 22 hours with no problems. Sent from my Pixel 4a (5G) using Tapatalk
  16. Any update? I know I set my Max and Minimum cpu frequencies to the same for both the 4 cores and 2 upper cores. and never looked back lol If ondemand and cpu frequencies have been fixed that would probably add some robustness.
  17. Howdy Igor! A workaround I found that seems to work for me, was to boot from the latest release from an SD card, and update the bootloader. It seemed to let me back in and stopped giving me the login loop i was experiencing. I am running Buster.
  18. I set my Helios64 up last week, and placed it at it's final home/location. My unit had been running perfectly fine for 2 days then sometime this morning before I woke up it crashed and auto rebooted. System has been up for 2 hours now. Following the guide above, I have changed my cpufreq to 400mhz-1.4Ghz and I set the governor to OnDemand and will see if stability will last beyond two days . Hopefully whatever the culprit is, will be fully ironed out by or before the Armbian becomes fully supported I was just on the site and it now says supported lol. Thanks again to all!
  19. Thank you! I canceled delivery of the psu I ordered and then ordered the one you linked, It has arrived today and the issue is now resolved! Thank you for saving me from making a grave mistake!
  20. I Have ordered a New Power Supply and will test the system with it when it comes in. It was kinda hard to find a 4pin with 12v 8 amps, I'm still searching for my multimeter but can't seem to find it. I do appreciate your guidance and support! If the new Power Supply has the same issue which (which I doubt), I will then order a new Multimeter and do some testing when I get back home on Sunday. Thanks Again!
  21. Seems like my Helios4 may have the same issue, I've at least diagnosed it to the point that I know it's a power issue, If I mess with the cables, I can get 2 drives to boot, but the other 2 either wont show or if i get it going it seems like the system itself wont boot up. I am currently looking for my multimeter to test this part out. I don't currently own a soldering iron but can quickly get one, Any particular Solder that you recommend for the Dirty Solder?
×
×
  • Create New...

Important Information

Terms of Use - Privacy Policy - Guidelines