Jump to content

MattWestB

  • Posts

    34
  • Joined

  • Last visited

 Content Type 

Forums

Member Map

Store

Crowdfunding

Applications

Everything posted by MattWestB

  1. @DmitryS The MCC is U2300 and on the underside of the PCB you have 2 test points TP2300 and TP2301 (GND). You can trying shutting them with one high ohm resistor for being safe (or only some metal if not playing safe and can damage the board) and putting in one USB cable from your PC in the OTG port and see if the SOC is booting in masc rom more. Some of the hardware specialist here is knowing more but im 95% sure its the masc rom TPs on your board but no one can grantee it before have testing it and its all on your own risk !! Its also looks you is having one unpopulated pin row for console that can being good if need doing more debug (after getting your board booting OK).
  2. Great thanks @jock and CO !! | _ \| |/ /___ /___ // |( _ ) | __ ) _____ __ | |_) | ' / |_ \ |_ \| |/ _ \ | _ \ / _ \ \/ / | _ <| . \ ___) |__) | | (_) | | |_) | (_) > < |_| \_\_|\_\____/____/|_|\___/ |____/ \___/_/\_\ Welcome to Armbian 22.08.0-trunk Jammy with Linux 5.18.6-rockchip64 HA is up and ruing with ZHA and one Open Thread border router and looks working OK 😘 (upgraded production Ubuntu 22.04 with new kernel on eMMC without testing on SD-Card)
  3. @Bandar Is it one comport on the opposite side of the PCB from the HDMI connection ? One is GND and 2 "small" lanes plus one more that is likely power supply (3.3 or 5 volt and no need to using). By the way its looks you is having one pad for getting the device is masc ROM on the left side from the likely comport connection. @jockCan the "[ OK ] Found device /dev/ttyS2" indicating that the the SD-card is not OK configured and the system is trying using it for ttyS2 and is locking the SD-card liens and crashing ?? Trying disabling the ttyS2 in the config and the SD-card its working ?
  4. @Revsearcher Also look under the green quality test sticker on the under side if some pads is being hidden there. You have 2 pads on the upper side hear the unpopulated ram / MMC pads that very likely is forcing mask rom mode but cant being 100% sure if not tested with high impedance resistor shutting them or oscilloscope. I think its one RL3318 box that is super stripped like my and many other RK3228A boxes and the HDMI is not working with armbian then have doing no standard layout of the PCB and need patching the RK chip for getting it working that we dont knowing for the moment. If its so you shall getting the Ethernet requesting one IP-address if waiting some minute with multi too and can connecting with SSH to it but then is normally the LED looking OK. Some PB is using the SD-card pins for UART if no SD-card is inserted but i think its not supported for all PCBs (its using 2 pin serial = UART if not card is in and 4 pin serial then card is inserted and loading the MMC module for the SD-card).
  5. @jockYour kernel with extra settings looks working OK with docker and i have not have any problems running some (13) containers with it for some weeks ! But Home assistant is needing APPARMOR being enabled in the kernel (i can installing the packages but its not working then the kernel is not supporting it) and i think it shall not being any problems with other programs doing it then its more or less standard in all Linux "modern" distributions. Also the "standard" armbian is having it enabled (in the Nanopi neo core its enabled and HA is working OK and dont complaining about missing it and is using it). Pleas cooking one updated kernel with apparmor enable for testing then you have time doing one fast patching. Great thanks for your work on our Boxes for getting real OS working great on them !!!
  6. @fedex My test script is showing the same and i can installing portainer and / or docker agent and its working OK. What is HA complaining then you is trying installing it ? Also the CPU is 32 bits so need using installing the "armv7l" version by selecting "raspberrypi2" or its failing. @jock I think we shall not hijacking the thread with no Armbian things and you must saying if we shall stop spamming it with HA problems.
  7. @fedex Try running the check script and see if you have al installed and working for docker. https://docs.docker.com/engine/install/linux-postinstall/#kernel-compatibility What is not working with the install of HA ? Complaining on brub or somthing else ?
  8. @fedex Install HA as raspberry pi 2 (= 32 bits) and its not working. Then do this: And puls audio is using 200% CPU so set CPU usage to minimum for the HA container and its only using 25% CPU. Need do the CPU patching after every restart of docker / the system. Its one addon that fixing the sound problem but its not working in me new Armbian (perhaps its the missing appamor that is doing it).
  9. @jock Docker looks working OK buzt i have problem with the sound in HA container that is eating 200% of all CPUs. Its one fix for it by loading one addon that is tricking the system but its cant being loaded. My theory is that is appamor that is missing and cant forcing the security for doing the patching. May i request adding appamor module being added in the kernel and in the normal armbian kernels (if the module its compiled armbian is having it disabled by default and need being activated in the kernel comandline for getting it loaded so it shall being safe) ? Thanks in advance !!
  10. @jock I was trying installing the updated kernel but it was not working on my RK3228 box then i have focal installed on one USB stick and Jermy on the EMMC but after removing the USB stick and updating the system docker is staring OK and i can installing HA and it running but the fix for audio lock that is burning 400% CPU is not working but i thing its not problem in the host OS more that i is reusing the SC-card for docker data and its some bad written in it then being mounted with other versions. Shall doing one clean install and reformatting the "internal" SD-card so its no getting old junk in the system and reporting back. So for docker is your test kernel very OK then i have 8 container inclusive portainer and portainer agent running on it :-)) Great thanks for fixing the problems and hope more users can getting docker it working on there boxes !!! Mvh Mattias
  11. @fedex I was only running the test script and providing the information wot kernel modules that is not configurated in the kernel. I have one RK3318 and one Nanopi Neo up and running that is having all in place and looks working good with HA with ZHA and OTBR up and running :-)) To getting it working you must compiling your own kernel or waiting and hoping @jock is fixing one upgraded kernel for us that is having all modules compelled OK. Link to the docker test script you can finding here: https://docs.docker.com/engine/install/linux-postinstall/#kernel-compatibility
  12. Ubuntu 22.04 LTS rk3318-box is up and running nicely with working Docker and HA supervised looks working OK. Up time is only some hours after install but the prereleases was also working stable so hopefully it shall doing the same. Great thank devs for making it happening !!!
  13. Very true fedex !! Also it can being more sub modules BPF that must being enabled if reading post made in some forums. The Focal was working well also docker was running stable and the 22.04 betas was not stable at all but docker was running on them but its looks like 22.04 GA is up and running for around 2 days and its not crashing so looks great :-)). Have comparing with armbian focal running on one NanoPi with docker running stable and this modules is missing in 22.04 from the docker script is: - CONFIG_CGROUP_BPF: missing - CONFIG_CGROUP_HUGETLB: missing - CONFIG_SECURITY_SELINUX: missing - CONFIG_SECURITY_APPARMOR: missing - CONFIG_EXT3_FS_XATTR: missing - Storage Drivers: - "aufs": - CONFIG_AUFS_FS: missing I think APPARMOR is on must for running Home assistant and many other systems / programs. The EXT3 can being good for some user but not for my systems. Also the zfs is in both install not configured but i think (= not knowing) it can being good for not burning the flash so fast so if you think it good enabling it: - Storage Drivers: - "zfs": - /dev/zfs: missing - zfs command: missing - zpool command: missing Edit: zfs is normally not supported in Linux kernel and very likely not needed for our devices. Great thanks in for bringing Ubuntu 22.04 for our boxes !!!
  14. Running dockers install testing script bash ./check-config.sh and getting: root@rk322x-box:~# bash ./check-config.sh warning: /proc/config.gz does not exist, searching other paths for kernel config ... info: reading kernel config from /boot/config-5.15.25-rk322x ... Generally Necessary: - cgroup hierarchy: cgroupv2 Controllers: - cpu: available - cpuset: available - io: available - memory: available - pids: available - CONFIG_NAMESPACES: enabled - CONFIG_NET_NS: enabled - CONFIG_PID_NS: enabled - CONFIG_IPC_NS: enabled - CONFIG_UTS_NS: enabled - CONFIG_CGROUPS: enabled - CONFIG_CGROUP_CPUACCT: enabled - CONFIG_CGROUP_DEVICE: enabled - CONFIG_CGROUP_FREEZER: enabled - CONFIG_CGROUP_SCHED: enabled - CONFIG_CPUSETS: enabled - CONFIG_MEMCG: enabled - CONFIG_KEYS: enabled - CONFIG_VETH: enabled (as module) - CONFIG_BRIDGE: enabled - CONFIG_BRIDGE_NETFILTER: enabled (as module) - CONFIG_IP_NF_FILTER: enabled (as module) - CONFIG_IP_NF_TARGET_MASQUERADE: enabled (as module) - CONFIG_NETFILTER_XT_MATCH_ADDRTYPE: enabled (as module) - CONFIG_NETFILTER_XT_MATCH_CONNTRACK: enabled (as module) - CONFIG_NETFILTER_XT_MATCH_IPVS: enabled (as module) - CONFIG_NETFILTER_XT_MARK: enabled (as module) - CONFIG_IP_NF_NAT: enabled (as module) - CONFIG_NF_NAT: enabled (as module) - CONFIG_POSIX_MQUEUE: enabled - CONFIG_CGROUP_BPF: missing Optional Features: - CONFIG_USER_NS: enabled - CONFIG_SECCOMP: enabled - CONFIG_SECCOMP_FILTER: enabled - CONFIG_CGROUP_PIDS: enabled - CONFIG_MEMCG_SWAP: enabled (cgroup swap accounting is currently enabled) - CONFIG_BLK_CGROUP: enabled - CONFIG_BLK_DEV_THROTTLING: enabled - CONFIG_CGROUP_PERF: enabled - CONFIG_CGROUP_HUGETLB: missing - CONFIG_NET_CLS_CGROUP: enabled (as module) - CONFIG_CGROUP_NET_PRIO: enabled - CONFIG_CFS_BANDWIDTH: enabled - CONFIG_FAIR_GROUP_SCHED: enabled - CONFIG_RT_GROUP_SCHED: enabled - CONFIG_IP_NF_TARGET_REDIRECT: enabled (as module) - CONFIG_IP_VS: enabled (as module) - CONFIG_IP_VS_NFCT: enabled - CONFIG_IP_VS_PROTO_TCP: enabled - CONFIG_IP_VS_PROTO_UDP: enabled - CONFIG_IP_VS_RR: enabled (as module) - CONFIG_SECURITY_SELINUX: missing - CONFIG_SECURITY_APPARMOR: missing - CONFIG_EXT3_FS: enabled - CONFIG_EXT3_FS_XATTR: missing - CONFIG_EXT3_FS_POSIX_ACL: enabled - CONFIG_EXT3_FS_SECURITY: enabled (enable these ext3 configs if you are using ext3 as backing filesystem) - CONFIG_EXT4_FS: enabled - CONFIG_EXT4_FS_POSIX_ACL: enabled - CONFIG_EXT4_FS_SECURITY: enabled - Network Drivers: - "overlay": - CONFIG_VXLAN: enabled (as module) - CONFIG_BRIDGE_VLAN_FILTERING: enabled Optional (for encrypted networks): - CONFIG_CRYPTO: enabled - CONFIG_CRYPTO_AEAD: enabled - CONFIG_CRYPTO_GCM: enabled - CONFIG_CRYPTO_SEQIV: enabled - CONFIG_CRYPTO_GHASH: enabled - CONFIG_XFRM: enabled - CONFIG_XFRM_USER: enabled (as module) - CONFIG_XFRM_ALGO: enabled (as module) - CONFIG_INET_ESP: enabled (as module) - "ipvlan": - CONFIG_IPVLAN: enabled (as module) - "macvlan": - CONFIG_MACVLAN: enabled (as module) - CONFIG_DUMMY: enabled - "ftp,tftp client in container": - CONFIG_NF_NAT_FTP: enabled (as module) - CONFIG_NF_CONNTRACK_FTP: enabled (as module) - CONFIG_NF_NAT_TFTP: enabled (as module) - CONFIG_NF_CONNTRACK_TFTP: enabled (as module) - Storage Drivers: - "aufs": - CONFIG_AUFS_FS: missing - "btrfs": - CONFIG_BTRFS_FS: enabled - CONFIG_BTRFS_FS_POSIX_ACL: enabled - "devicemapper": - CONFIG_BLK_DEV_DM: enabled - CONFIG_DM_THIN_PROVISIONING: enabled - "overlay": - CONFIG_OVERLAY_FS: enabled (as module) - "zfs": - /dev/zfs: missing - zfs command: missing - zpool command: missing Limits: - /proc/sys/kernel/keys/root_maxkeys: 1000000 The "zfs" looks not being used in the proviso version but was working OK without it. But is still little more modules that is missing in the kernel for making docker working OK:-((
  15. In Ubuntu 22.04 is Docker / Portiner broken then missing handles is disabled in the kernel # CONFIG_BPF_SYSCALL is not set. docker: Error response from daemon: failed to create shim: OCI runtime create failed: container_linux.go:380: starting container process caused: process_linux.go:545: container init caused: process_linux.go:508: setting cgroup config for procHooks process caused: bpf_prog_query(BPF_CGROUP_DEVICE) failed: function not implemented: unknown. Edit: It can also being problems with docker is using CGroupsV2 and that is not supported in all installations and need patching the system for using V1.
  16. Great thanks for the Ubuntu 22.04 LTS rk322x-box that is installed and waiting to see if its production stable !! Great work done !!!
  17. @javaxsousa I was posting on link of my R29-MXQ-LP3-V2.3-00908 that have the same pads on the underside and it more then likely the same on your board and is the local system console. You can taking on look on my gti-hub that i have posting photos and also working new loader for my board. https://github.com/MattWestb/R29-MXQ-LP3-V2.3-00908
  18. @javaxsousa look on this post: Its looks the same layout under the CPU and the 2 pads was the system console on my board.
  19. @javaxsousa look on the under side of the PCB and if its 2 pads near the CPU. My version was having it and it was the RX and TX for the system console. Is the LED blinking then booting multitool ? If not you are still in brick mode.
  20. @Antoxic i was having similar problem with one RK3228A box and it was working then i was finding the right loader for the box it was possible using RK tools in Linux and also Windows utility's.
  21. Hi @karkow and thanks for your inspiration that was making my testing this box !!! I think its working with all current ARMbian images (i was trying legacy deb and all ubuntos and its was working OK) only first you need burning one copy off mutlitool on one SD-card and your selected ARMbian one one other sd-card or USB-stick. If you running Linux you can using DD bu if windows i think Mintools is the easiest way (MiniTool Partition Wizard Free). Then you is having empty space in the beginning of the multitool SD and after that more partitions. I was copy the ARMbian ext4 partition from the USB dick to the multitool but after the partitions that is normally used (i think around 52 or 61 Mb from the start of the dick if to less space its not booting and start from the beginning) and setting the partition acting is important. One way can being using "USB Duplicator Image Creator.exe" then you can copy the beginning of the multitool disk to one image and dont need re flashing all and starting from zero every time its not working. Then getting it working is the u-boot from multitool booting OK and searching for one working system on USB and SD-card (then it was not finding and multiol partition) and if finding one its trying booting it so with the first part (52-61 Mb i think it was) of multitool you can kick starting from SD-card to one USB-disk the the last part is not there and starting multitool. I have asking if i can posting my patched "boot part" of multitools buut part but i have not getting one yes = no in my world but i can sending it to you pf you is PM my. If you is good on Linux its better using DD but im not being so good on it and is morally running my laptop on Windows. If getting problem pleas ask so you is getting your bot up and running.
  22. Sorry @jock i was replaying (but not good done) of @Petroz posted dmesg files that was looking little strange but realistic. I hope my new box is coming in some days from Spain.
  23. From the log: MMC0 = SD-Card MMC1 = is the WiFi card but i think its not finding the firmware for it. MMC2 = eMMC but its being probed with very strange clock speed. MMC3 = not used or its the eMMC. With RK-3228 boxes its not working good at the first boot then the system is loading NAND and eMMC support. If first config no eMMC and only NAND and rebooting and the config only eMMC support and booting and updating the system its being detected in full speed and working OK. For the WiFi have you loading the full firmware pack ? The problematic files is in the git https://github.com/armbian/firmware/blob/master/brcm/brcmfmac4330-sdio.rockchip,rk3318-box.txt.
  24. Thanks for the updated RK3188 system @balbes150 its look running OK but i dont knowing if its being stable (the version before was crashing some time every 24H) but looks good after some hours. The only large problem is missing modules that is exuded in the kernel that is making docker not working. Then looking in the kernel config is most network modules disabled in the kernel. Can you compiling one updated kernel with modules with enough function for running docker with bridged network ? I dont have enough knowledge and hardware (only one converterebal with 4G RAM) for compiling all from your source code. Thanks in advance !! Mvh Mattias
  25. Thanks @jock for comments. The problem is that user like my with boxes that the HDMI is not working and then cant getting mulltitool working at all also from serial console so being complete blind and if copy your first part of mulltitool and copy one armbian to on partitation after the boot part is possible installing armbian without problem in EMMC with SSH. Is it OK posing part of your mulltitool with added system partition on git-hub if some user is requesting it ? I have only found focal with desktop and installing it i only have little more than 2G free flash and HA is needing that or more so i need mounting the SD-card in docker storage directory then i have 64G for containers and still can installing things and doing updates. The LEDs is right configuration and changing is not helping (the LED is power off mode) so i must trying your trigger if google can giving my the right guldens. @fabiobassa you are more then welcome PM my or you can open issue in one of my git-hubs repros like https://github.com/MattWestb/R29-MXQ-LP3-V2.3-00908. Im not one expert on HA but have much knowledge with ZHA part and the Zigbee system and device. If i can help with some problem or sharing some good or bad experience is very OK for my and you looks have much knowledge in other interesting technical things. PS the soldering is not so good that it can being but working and it can being better done but with the age its more Shaking Stevens have doing it ;-)) Mvh Mattias
×
×
  • Create New...