U-Boot 2018.11-armbian (May 06 2021 - 19:47:58 +0000)
Model: Tinker-RK3288
DRAM: 2 GiB
MMC: dwmmc@ff0c0000: 1, dwmmc@ff0f0000: 0
Loading Environment from EXT4... Card did not respond to voltage select!
In: serial
Out: serial
Err: serial
Model: Tinker-RK3288
Net: eth0: ethernet@ff290000
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found U-Boot script /boot/boot.scr
3395 bytes read in 1 ms (3.2 MiB/s)
## Executing script at 00000000
Boot script loaded from mmc 1
161 bytes read in 1 ms (157.2 KiB/s)
5829234 bytes read in 2450 ms (2.3 MiB/s)
8580280 bytes read in 3588 ms (2.3 MiB/s)
** File not found /boot/dtb/rk3288-tinker-s.dtb **
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
No FDT memory address configured. Please configure
the FDT address via "fdt addr <address>" command.
Aborting!
286 bytes read in 1 ms (279.3 KiB/s)
Applying kernel provided DT overlay rockchip-i2c1.dtbo
No FDT memory address configured. Please configure
the FDT address via "fdt addr <address>" command.
Aborting!
286 bytes read in 1 ms (279.3 KiB/s)
Applying kernel provided DT overlay rockchip-i2c4.dtbo
No FDT memory address configured. Please configure
the FDT address via "fdt addr <address>" command.
Aborting!
311 bytes read in 1 ms (303.7 KiB/s)
Applying kernel provided DT overlay rockchip-spi2.dtbo
No FDT memory address configured. Please configure
the FDT address via "fdt addr <address>" command.
Aborting!
537 bytes read in 2 ms (261.7 KiB/s)
Applying kernel provided DT overlay rockchip-spidev2.dtbo
No FDT memory address configured. Please configure
the FDT address via "fdt addr <address>" command.
Aborting!
287 bytes read in 1 ms (280.3 KiB/s)
Applying kernel provided DT overlay rockchip-uart1.dtbo
No FDT memory address configured. Please configure
the FDT address via "fdt addr <address>" command.
Aborting!
287 bytes read in 1 ms (280.3 KiB/s)
Applying kernel provided DT overlay rockchip-uart2.dtbo
No FDT memory address configured. Please configure
the FDT address via "fdt addr <address>" command.
Aborting!
Error applying DT overlays, restoring original DT
** File not found /boot/dtb/rk3288-tinker-s.dtb **
## Loading init Ramdisk from Legacy Image at 21000000 ...
Image Name: uInitrd
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 5829170 Bytes = 5.6 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
ERROR: Did not find a cmdline Flattened Device Tree
Could not find a valid device tree
SCRIPT FAILED: continuing...
starting USB...
USB0: USB1: scanning bus 0 for devices... cannot reset port 1!?
cannot reset port 3!?
5 USB Device(s) found
scanning bus 1 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Device 0: unknown device
ethernet@ff290000 Waiting for PHY auto negotiation to complete....... done
Speed: 1000, full duplex
BOOTP broadcast 1
BOOTP broadcast 2
*** Unhandled DHCP Option in OFFER/ACK: 125
*** Unhandled DHCP Option in OFFER/ACK: 125
DHCP client bound to address 192.168.1.113 (457 ms)
*** Warning: no boot file name; using 'C0A80171.img'
Using ethernet@ff290000 device
TFTP from server 192.168.1.1; our IP address is 192.168.1.113
Filename 'C0A80171.img'.
Load address: 0x800800
Loading: T T T T T T T T T T
Retry count exceeded; starting again
missing environment variable: pxeuuid
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/01-2c-4d-54-42-b1-16
Speed: 1000, full duplex
Using ethernet@ff290000 device
TFTP from server 192.168.1.1; our IP address is 192.168.1.113
Filename 'pxelinux.cfg/01-2c-4d-54-42-b1-16'.
Load address: 0x100000
Loading: T T T