javaxsousa

@buratino sorry my delay of answer this question, but above i put my config, i used "u-boot-2021.07" version IK316-EMCP_defconfig.txt @Matheus Gomes the chip Ik316 is the same H616/H313

Do you have an dtb file of your box tv??

do you have any pictures of board of your box tv??

@andre2b From what I could see, your TV box does not have the EMC chip, so I suggest testing with other images, because despite showing Ik316, the chip is actually an H313/H616. Test is below too https://github.com/warpme/miniarch

@andre2b sorry my delay of answer this question , but I used image from armbian but I compile u-boot-sunxi-with-spl.bin and make this command: dd if=u-boot-sunxi-with-spl.bin of=/dev/yourcard bs=1k seek=8 conv=fsync on sd card with armbian installed. I attached a copy of u-boot-sunxi-with-spl.bin here, try it and see if it works I didn't send the complete image because I still haven't been able to recompile it with the complete Armbian. u-boot-sunxi-with-spl.bin

i used kernel: Linux version 5.19.16-sunxi64 with Armbian_22.08.7_Orangepizero2_jammy_edge_5.19.16.img, this version works but HDMI ,network and audio not work

well, after many attempts I managed to boot Armbian on the TVbox with emcp chip, you really have to change the parameters in defconfig and recompile to generate ou-boot-sunxi-with-spl.bin,but the internal network card still doesn't work from the ik316 which is the same h616 used network usb and the HDMI output doesn't work. The latest version of Armbian: Armbian_23.8.3_Orangepizero2_b gives error after u-boot: starting systemd-udevd version 252.12-1~deb12u1 [ 2.600465] thermal thermal_zone0: gpu-thermal: critical temperature reached, shutting down [ 2.608985] reboot: HARDWARE PROTECTION shutdown (Temperature too high) I used the version Armbian 22.08.6 Jammy with bleeding edge Linux 5.19.16-sunxi64 and with modified spl.bin

I would like to know how to recompile with the image, I'm using the orangepi build, but every time I change u-boot.cfg in the compilation it returns the original settings. I have the problem that in addition to the emcp memory, I also change the axp which is the 305 and not the 806

https://forum.armbian.com/topic/29824-tvbox-m4xq-with-ik316-emcp-10/

I have this tvbox model as per the attached photos. I tried to run the image: Armbian_23.5.2_Orangepizero2_bookworm_current_6.1.30 but the error appeared: U-Boot SPL 2021.04 (May 25 2023 - 13:06:08 +0200) DRAM:This DRAM setup is currently not supported. I was able to extract the dtb files along with the boot.img and bootloader.img. but I'm sending the files that I dumped. The link is below because I couldn't attach it here.from this tvbox. can anybody help me? dumped dtb and boot.img and bootloader.img: https://we.tl/t-xp8WGoP80f bootik316.txt

i used this image: Armbian_23.5.2_Orangepizero2_bookworm_current_6.1.30

my tv box uses the same chip,Ik316=h313, but when I use the h616 image it gives the following error U-Boot SPL 2021.04 (May 25 2023 - 13:06:08 +0200) DRAM:This DRAM setup is currently not supported. Attached I send the boot log and the images of my tvbox bootik316.txt

After a while i finally got my tvbox H96max with h616 working, with version Armbian 21.08.1 Bullseye, but only one usb port works and the ethernet does not work, I am using a usb hub with the keyboard and an external usb ethernet

After reading the comments here from the group, I decided to open my h96max tvbox, and I realized that it had a serial connector, when plugging into a usb serial interface, I got these results when loading armbian. 515][AUTO DEBUG]16 bit,1 ranks training success! [522]DRAM CLK =720 MHZ [525]DRAM Type =3 (3:DDR3,4:DDR4,7:LPDDR3,8:LPDDR4) [531]Actual DRAM SIZE =1024 M [534]DRAM SIZE =1024 MBytes, para1 = 30fb, para2 = 4000001, dram_tpr13 = 6041 [547]DRAM simple test OK. [549]rtc standby flag is 0x0, super standby flag is 0x0 [555]dram size =1024 [557]*****dram handle ok**** [560]card no is 0 [562]sdcard 0 line count 4 [565][mmc]: mmc driver ver 2019-12-19 10:41 [569][mmc]: sdc0 spd mode error, 2 [573][mmc]: set f_max to 50M, set f_max_ddr to 25M [577][mmc]: mmc 0 bias 0 [585][mmc]: Wrong media type 0x0 [589][mmc]: ***Try SD card 0*** [599][mmc]: HSSDR52/SDR25 4 bit [602][mmc]: 50000000 Hz [604][mmc]: 15084 MB [606][mmc]: ***SD/MMC 0 init OK!!!*** [707]Loading boot-pkg Succeed(index=0). [711]Entry_name = u-boot [720]Entry_name = monitor [724]Entry_name = dtbo [727]Entry_name = dtb [730]Jump to second Boot. NOTICE: BL3-1: v1.0(debug):9fecd83 NOTICE: BL3-1: Built : 17:08:29, 2020-05-28 NOTICE: BL3-1 commit: 8 ERROR: Error initializing runtime service tspd_fast NOTICE: BL3-1: Preparing for EL3 exit to normal world NOTICE: BL3-1: Next image address = 0x4a000000 NOTICE: BL3-1: Next image spsr = 0x1d3 U-Boot 2018.05-armbian (Aug 28 2021 - 20:00:15 +0200) Xunlong Software [00.807]CPU: Allwinner H616 [00.810]Model: Orange Pi Zero 2 I2C: ready [00.815]DRAM: 1 GiB Relocation Offset is: 35ec9000 [00.855]secure enable bit: 0 [00.858]PMU: AXP806 [00.862]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=400Mhz [01.044]sunxi overlay merged okqv [01.047]drv_disp_init [01.076]__clk_enable: clk is null. tv_init()950 fetch tv0 err. [01.082]drv_disp_init finish [01.085]gic: sec monitor mode [01.090]flash init start [01.092]workmode = 0,storage type = 1 [01.095]MMC: 0 [01.097]get mem for descripter OK ! card_caps:0x30000002 host_caps:0x3000003f [01.125]sunxi flash init ok [01.128]Loading Environment from FAT... [01.131]get mem for descripter OK ! ** Bad device mmc 1 ** Failed (-5) [01.147]usb burn from boot delay time 0 weak:otg_phy_config [01.160]usb prepare ok [01.963]overtime [01.967]do_burn_from_boot usb : no usb exist [01.971]boot_gui_init:start card_caps:0x30000002 host_caps:0x3000003f 177 bytes read in 21 ms (7.8 KiB/s) Set HDMI disp_mode to 1080p60 177 bytes read in 21 ms (7.8 KiB/s) Set fb0_width to 1280 Set fb0_height to 720 [02.317]boot_gui_init:finish [02.320]bmp_name=/boot/boot.bmp 230454 bytes read in 43 ms (5.1 MiB/s) [02.377]update dts Net: [02.380]No ethernet found. Hit any key to stop autoboot: 1 0 no mmc device at slot 1 card_caps:0x30000002 host_caps:0x3000003f switch to partitions #0, OK mmc0 is current device Scanning mmc 0:1... Found U-Boot script /boot/boot.scr 2612 bytes read in 25 ms (101.6 KiB/s) ## Executing script at 43100000 U-boot loaded from SD Boot script loaded from mmc 177 bytes read in 21 ms (7.8 KiB/s) 6695987 bytes read in 594 ms (10.7 MiB/s) 24127560 bytes read in 2044 ms (11.3 MiB/s) ## Booting kernel from Legacy Image at 41000000 ... Image Name: Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 24127496 Bytes = 23 MiB Load Address: 41000000 Entry Point: 41000000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 43300000 ... Image Name: uInitrd Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 6695923 Bytes = 6.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Ramdisk to 4999d000, end 49fffbf3 ... OK reserving fdt memory region: addr=48000000 size=1000000 ## Linux machid: 00000000, FDT addr: 7be89580 Starting kernel ... Loading, please wait... Starting version 247.3-6 Loading, please wait... Starting version 247.3-6 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... Scanning for Btrfs filesystems done. Begin: Will now check root file system ... fsck from util-linux 2.36.1 [/sbin/fsck.ext4 (1) -- /dev/mmcblk0p1] fsck.ext4 -a -C0 /dev/mmcblk0p1 /dev/mmcblk0p1: recovering journal /dev/mmcblk0p1: clean, 40682/131264 files, 373396/436224 blocks done. done. Begin: Running /scripts/local-bottom ... done. Begin: Running /scripts/init-bottom ... done.

sorry for the post above, I had understood that the colleague had achieved it with tvboc tanix6s

I buy a h96max tv box with h616 processor with 2gb ram and 16gb of emmc, however, i downloaded and loaded the armbian version Armbian_21.08.1_Orangepizero2_bullseye_legacy_4.9.280.img.xz, as said above it would work on tv box, but it until the armbian logo appears, loading, but it hangs there. Does anyone have any ideas on how to modify the boot?