It's not compatibility with latest bootloader?
[cide]
[0000.125] [L4T TegraBoot] (version 00.00.2018.01-l4t-c536fca9)
[0000.131] Processing in cold boot mode Bootloader 2
[0000.135] A02 Bootrom Patch rev = 1023
[0000.139] Power-up reason: pmc por
[0000.142] No Battery Present
[0000.145] pmic max77620 reset reason
[0000.148] pmic max77620 NVERC : 0x40
[0000.151] RamCode = 0
[0000.154] Platform has DDR4 type RAM
[0000.157] max77620 disabling SD1 Remote Sense
[0000.161] Setting DDR voltage to 1125mv
[0000.165] Serial Number of Pmic Max77663: 0xf24c9
[0000.173] Entering ramdump check
[0000.176] Get RamDumpCarveOut = 0x0
[0000.179] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8
[0000.184] Last reboot was clean, booting normally!
[0000.189] Sdram initialization is successful
[0000.193] SecureOs Carveout Base=0x00000000ff800000 Size=0x00800000
[0000.199] Lp0 Carveout Base=0x00000000ff780000 Size=0x00001000
[0000.205] BpmpFw Carveout Base=0x00000000ff700000 Size=0x00080000
[0000.211] GSC1 Carveout Base=0x00000000ff600000 Size=0x00100000
[0000.216] GSC2 Carveout Base=0x00000000ff500000 Size=0x00100000
[0000.222] GSC4 Carveout Base=0x00000000ff400000 Size=0x00100000
[0000.228] GSC5 Carveout Base=0x00000000ff300000 Size=0x00100000
[0000.234] GSC3 Carveout Base=0x000000017f300000 Size=0x00d00000
[0000.250] RamDump Carveout Base=0x00000000ff280000 Size=0x00080000
[0000.256] Platform-DebugCarveout: 0
[0000.259] Nck Carveout Base=0x00000000ff080000 Size=0x00200000
[0000.265] Non secure mode, and RB not enabled.
[0000.269] Read GPT from (4:0)
[0000.442] Csd NumOfBlocks=124735488
[0000.447] Set High speed to 1
[0000.450] Error mask set in wait for cmd complete with error 0x3 in HwSdmmcWai
[0000.460] Command complete wait failed with error 0x3 Interrupt 0x18001
[0000.467] Number of retries left 4
[0000.476] Using GPT Primary to query partitions
[0000.480] Read PT from (2:0)
[0000.496] Using BFS PT to query partitions
[0000.501] Loading Tboot-CPU binary
[0000.530] Verifying TBC in OdmNonSecureSBK mode
[0000.540] Bootloader load address is 0xa0000000, entry address is 0xa0000258
[0000.547] Bootloader downloaded successfully.
[0000.551] Downloaded Tboot-CPU binary to 0xa0000258
[0000.556] MAX77620_GPIO5 configured
[0000.559] CPU power rail is up
[0000.562] CPU clock enabled
[0000.566] Performing RAM repair
[0000.569] Updating A64 Warmreset Address to 0xa00002e9
[0000.574] PT: Partition RP1 NOT found !
[0000.578] Warning: Find Partition via PT Failed
[0000.582] Bootloader DTB invalid, fallback to kernel DTB.
[0000.588] PT: Partition DTB NOT found !
[0000.592] Warning: Find Partition via PT Failed
[0000.596] Error is 1
[/code]
Not created DTB partition and partition RP1 not found huh?
