Nikolai Asparuhov

  • Content Count

    22
  • Joined

  • Last visited

About Nikolai Asparuhov

  • Rank
    Member

Recent Profile Visitors

755 profile views
  1. Sorry my bad. ifconfig: wlan1 Link encap:Ethernet HWaddr 00:e0:5d:00:01:a7 inet addr:192.168.100.10 Bcast:192.168.100.255 Mask:255.255.255.0 inet6 addr: fe80::2e0:5dff:fe00:1a7/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:50531 errors:0 dropped:26831 overruns:0 frame:0 TX packets:248 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:13014020 (12 MiB) TX bytes:31587 (30.8 KiB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00
  2. Hello, I'm using armbian 5.25 on OPI Lite and wifi dongle 8192cu, after instaling these drivers: https://github.com/pvaret/rtl8192cu-fixes I saw that the interface drop half of the packages.... Can someone provide better drivers or tell me how to fix that? wlan1 Link encap:Ethernet HWaddr 00:13:ef:6b:24:e2 inet addr:192.168.100.7 Bcast:192.168.100.255 Mask:255.255.255.0 inet6 addr: fe80::213:efff:fe6b:24e2/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 -------->>>>>&g
  3. Hello I have a little problem with the usb devices, i use usb camera and if u plug the power supply to the OPI Lite board (5.25) it recognize the camera but it doesn't work well (stream with like 8-10 fps), after a software reboot, the device go to other Bus and the camera work fine with 15-30 fps stream. Before reboot, exact on first power of the board: Bus 006 Device 002: ID 058f:3822 Alcor Micro Corp. Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
  4. Could you give some more information, run: lsusb dmesg | grep usb sudo apt-get install v4l-utils, after that run v4l2-ctl --all
  5. It was about the mode, I'm so stupid, its regular libjpeg, not turbo, I'll try it on npm because there was the same problem, thanks a lot, and the same files compile without this mode problems on 5.23, is there any new changes on this direction in 5.25?
  6. Hello, I'm using OPI Lite with 5.25 armbian and there is a little problem with the permissions: root@orangepilite:~/Raws/libjpeg/jpeg-8c# ./configure -bash: ./configure: Permission denied root@orangepilite:~/Raws/libjpeg/jpeg-8c# sudo ./configure sudo: ./configure: command not found root@orangepilite:~/Raws/libjpeg/jpeg-8c# ls | grep configure configure configure.ac That appeared to me twice, first time i compile and install nodejs and npm was not recognized like a command (ask for permissions after use sudo just said command not found), this is my second hit to that problem, trying to
  7. Hmmm i guess ill need other type of charger because this one is from Orange Pi factory and its without removable cable.... But some other news are on 5.25 clean distro with 8192cu-fixed driver from git hub the dongle work fine, may be the problem was during the upgrade from 5.23 to 5.25. But the problem with the camera is the same. Boot time is low because of hostap services (around 25 sec to load them all) and the camera just don't wanna
  8. 2000mA standard power supply, if it was the problem why after the reboot make changes. And the interesting here is on first use the camera is on bus 006 and the dongle is no 002 after the reboot camera goes to bus 002 and the dongle go to 003...
  9. The second problem is the usb camera. It require reboot to be ok, if i disconnect the power supply and plug it in, it doesn't recognize the usb camera properly (almost in 70-80% of the test cases) dmesg output: [ 1.230073] usb 3-1: new high-speed USB device number 2 using sunxi-ehci [ 5.198897] usbcore: registered new interface driver rtl8192cu [ 5.211860] usbcore: registered new interface driver uvcvideo lsusb output: Bus 003 Device 002: ID 0bda:8176 Realtek Semiconductor Corp. RTL8188CUS 802.11n WLAN Adapter Bus 006 Device 002: ID 058f:3822 Alcor Micro Corp. lsmod outp
  10. I have dongle rtl8192cu it is so big garbage, until now i have some drivers for it but it crushes some times and have unstable connection. Try these drivers from git hub: https://github.com/pvaret/rtl8192cu-fixes and no improvement. Any suggestions?
  11. systemd-analyze blame output: 5.171s networking.service 5.171s networking.service 5.171s networking.service 5.171s networking.service 2.736s armhwinfo.service 2.422s isc-dhcp-server.service 1.782s systemd-logind.service 1.482s alsa-restore.service 1.193s rsyslog.service 1.159s systemd-user-sessions.service 1.156s rc-local.service 1.046s systemd-journal-flush.service 899ms loadcpufreq.service 809ms keyboard-setup.service 76
  12. Hello, greetings from Bulgaria and thanks for the OS. We use Orange Pi Lite and something may be is problem. Full boot time is around 1 min and 15 sec, how can we degree this time because it's so slow? When we was with 5.23 distro it was around 45 sec with same SD card and power supply.
  13. That's why i use esp-7 and it's work fine for now. Thanks for the japanese page, i'll take a look on it and will send you feedback about what i do. Thanks a lot for the solutions guys.
  14. Guys you do a great work with these distros, i get my respect and i admire you. Some little problem - i wanna to do automatic smart home and for my old devices that use Infra red signal i don't know how to transmit IR signal with Opi PC. I use ESP like middle-ware (send command to opi pc, that the opi pc send the command to esp which transmit it). Do someone know appropriate solution, because this one is sooo hard working and slow? Thanks in advance, for the time, support and the work you do!!!!!