Search the Community

Hello, I just installed the incredible Armbian on my OrangePiPlus. I can't find the EMMC Boot script nan-sata-install. Has something changed in the past I didn't noticed? with regards

Hi, I'm using the very latest armbian build fpr orangepi+, and i'm trying to nat the network from a wireless interface to another wireless interface. My own LAN works, dns server works too, so i can connect to the orangepi+ but i can't make nat working. Is there some known issue about it, or a custom tutorial for nat with this build? thanks for help

Hello, Can i use a 8TB hdd with orange pi plus 2? Is there any hardware / sotfware limitation, or i do something wrong? Armbian sees only 1.40 TB of 8 TB. I started from: https://www.armbian.com/orange-pi-plus-2and downloaded the jessie server. root@orangepiplus:~# uname -a Linux orangepiplus 3.4.112-sun8i #10 SMP PREEMPT Sun Oct 23 16:06:55 CEST 2016 armv7l GNU/Linux root@orangepiplus:~# dmesg |grep "sda\|scsi" [ 1.293990] scsi0 : usb-storage 3-1:1.0 [ 2.293196] scsi 0:0:0:0: Direct-Access ST8000AS 0002-1NA17Z 0009 PQ: 0 ANSI: 0 [ 2.295330] sd 0:0:0:0: [sda] 2743151276 512-byte logical blocks: (1.40 TB/1.27 TiB) [ 2.296410] sd 0:0:0:0: [sda] Write Protect is off [ 2.296427] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00 [ 2.297386] sd 0:0:0:0: [sda] No Caching mode page found [ 2.297398] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 2.300507] sd 0:0:0:0: [sda] No Caching mode page found [ 2.300522] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 2.313140] sda: unknown partition table [ 2.316414] sd 0:0:0:0: [sda] No Caching mode page found [ 2.316430] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 2.316443] sd 0:0:0:0: [sda] Attached SCSI disk root@orangepiplus:~# smartctl -i /dev/sda smartctl 6.4 2014-10-07 r4002 [armv7l-linux-3.4.112-sun8i] (local build) Copyright © 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: ST8000AS0002-1NA17Z Serial Number: Z840L0M7 LU WWN Device Id: 5 000c50 0916fb2a1 Firmware Version: AR17 User Capacity: 8,001,563,222,016 bytes [8.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5980 rpm Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 1.5 Gb/s) Local Time is: Tue Dec 6 14:25:04 2016 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled root@orangepiplus:~# cat /proc/partitions major minor #blocks name 8 0 1371575638 sda 179 0 15267840 mmcblk0 179 1 15114128 mmcblk0p1 179 32 4096 mmcblk0boot1 179 16 4096 mmcblk0boot0 root@orangepiplus:~# lsusb Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 05e3:0718 Genesys Logic, Inc. IDE/SATA Adapter Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 002: ID 1a40:0101 Terminus Technology Inc. 4-Port HUB Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub root@orangepiplus:~# cat /boot/config-3.4.112-sun8i |grep LBD CONFIG_LBDAF=y root@orangepiplus:~# lsmod Module Size Used by sunxi_cir 1601 0 pcf8591 3363 0 bmp085 3487 0 8189es 1076034 0 Hello, Can i use a 8TB hdd with orange pi plus 2? Is there any hardware / sotfware limitation, or do i something wrong? Armbian sees 1.40 TB hdd. I started from: https://www.armbian.com/orange-pi-plus-2and downloaded the jessie server. root@orangepiplus:~# uname -a Linux orangepiplus 3.4.112-sun8i #10 SMP PREEMPT Sun Oct 23 16:06:55 CEST 2016 armv7l GNU/Linux root@orangepiplus:~# dmesg |grep "sda\|scsi" [ 1.293990] scsi0 : usb-storage 3-1:1.0 [ 2.293196] scsi 0:0:0:0: Direct-Access ST8000AS 0002-1NA17Z 0009 PQ: 0 ANSI: 0 [ 2.295330] sd 0:0:0:0: [sda] 2743151276 512-byte logical blocks: (1.40 TB/1.27 TiB) [ 2.296410] sd 0:0:0:0: [sda] Write Protect is off [ 2.296427] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00 [ 2.297386] sd 0:0:0:0: [sda] No Caching mode page found [ 2.297398] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 2.300507] sd 0:0:0:0: [sda] No Caching mode page found [ 2.300522] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 2.313140] sda: unknown partition table [ 2.316414] sd 0:0:0:0: [sda] No Caching mode page found [ 2.316430] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 2.316443] sd 0:0:0:0: [sda] Attached SCSI disk root@orangepiplus:~# smartctl -i /dev/sda smartctl 6.4 2014-10-07 r4002 [armv7l-linux-3.4.112-sun8i] (local build) Copyright © 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: ST8000AS0002-1NA17Z Serial Number: Z840L0M7 LU WWN Device Id: 5 000c50 0916fb2a1 Firmware Version: AR17 User Capacity: 8,001,563,222,016 bytes [8.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5980 rpm Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 1.5 Gb/s) Local Time is: Tue Dec 6 14:25:04 2016 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled root@orangepiplus:~# cat /proc/partitions major minor #blocks name 8 0 1371575638 sda 179 0 15267840 mmcblk0 179 1 15114128 mmcblk0p1 179 32 4096 mmcblk0boot1 179 16 4096 mmcblk0boot0 root@orangepiplus:~# lsusb Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 05e3:0718 Genesys Logic, Inc. IDE/SATA Adapter Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 002: ID 1a40:0101 Terminus Technology Inc. 4-Port HUB Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub root@orangepiplus:~# cat /boot/config-3.4.112-sun8i |grep LBD CONFIG_LBDAF=y root@orangepiplus:~# lsmod Module Size Used by sunxi_cir 1601 0 pcf8591 3363 0 bmp085 3487 0 8189es 1076034 0 root@orangepiplus:~# parted -l Error: /dev/sda: unrecognised disk label Model: ST8000AS 0002-1NA17Z (scsi) Disk /dev/sda: 1404GB Sector size (logical/physical): 512B/512B Partition Table: unknown Disk Flags: root@orangepiplus:~# hdparm -g /dev/sda /dev/sda: geometry = 170753/255/63, sectors = 2743151276, start = 0

hi, I made a program on Orange pi minus (kernel 3.X)using wpa_supplicant for wifi direct. That worked fine (basically). But i have been asked to do it on Orange pi plus with Kernel 4.9. The wifi works when i using nmtui, but when i made a iw list i couldn't find my material and i am not able to configure P2P. I think the problem is the kernel version and not the Hardware because my card with kernel 3.X works on orange pi pc plus. So i am a bit lost, what can i do ? My guest is to modify the realtek module ? I am not sure if i am on the right direction... Thanks, Ps: Sorry for my english.

Hello, I installed Armbian/(debian jessie) on my Orange Pi Plus (EMMC). Works good, but i can't find the temp of the processor. (lm-sensors don't work/can't detect sensors) What should i do?

Hi I'm going use the terminal armbian and send AT commands to the gsm SIM800L, but I am uable to write these commands. I used screen and minicom like this : screen /dev/ttyS0 115200 & minicom -b 115200 -o -D /dev/ttyAMA0 I use to connect to ttyS3 but nothing happen i think the uart3 or pins 8 and 10 is not working or not enable of course i have ttyS3 in ls /dev list but not working. I've connected according to the following guidelines: i use : orange pi plus 2 board armbian for orange pi plus 2 SIM800L v2.0 image of my connection and board :

Hi. I tried to search the forum but it seems I put wrong search words... How should I install the display so I can run Geany (IDE)? Here is my data http://sprunge.us/WWGg

Hi, I am using orangepi+ with armbin debian jessie 5.20. I want to use softAp. orangepi+ have rtl8189etv, but when i am using Hostapd with isc-dhcp-server,if i enter to command line "iwlist wlan0 scan " , i can see kernel panic on screen. when i use bluetooth dongle (rtl8192cus), i can use hostapd and get scanlist.. rtl8189etv is not supported softAP?... or other problem? thanks...

Hi, I tryied a few times to run a RT kernel I built from https://github.com/igorpecovnik/lib as discribed in Armbian documentation and as in https://forum.armbian.com/index.php/topic/1950-orange-pi-pc-plus-armbian-guitarix-guitar-effectprocessor/page-2#entry16460. When executing compile.sh script it patch nice and good, then asks for Preemption Model and I chose 5 for Full Realtime. But when running the kernel into OrangePi it stucks in Starting Kernel. U-boot output: I am not choosing 1-4 for preemption model because I don't know if it will end up as an realtime kernel. The update from the older kernel to the rt one was done by dpkg -i on the deb files from the output/deb folder generated by Igor Pecovnik's scripts.

Hi everyone, i've been building a new distirbution based on armbian 5.2 server, on it has been compilled freepbx 13 and asterisk 13, i've added a webmin frontend for server management. It's my first apportation, i'm not a pro, but i wanted to share it with the community. The password for root is: "Armbian" The password for the user admin on freepbx is: "admin" In order to mount the image you need at least a 8gb sd card Here is the link to the download: https://mega.nz/#!eZ1gCKKY!UguIUAi-xa6K6iXXj37EZPFedgzCPdnSEQDBuoT3xRo (remember this image is for orange pi plus)* Finally, if you want to resize the partition toget all the space available on your disk, use this command: update.rc firstrun defaults Well, thanks for reading, and i hope it can be of some use to all of us.

Hi, I have some problem about softAp mode. I am using orangepi+ and, Armbian debian jessie server 5.20version. I want to connect web page using SmartPhone. and connect other AP(Client ap mode). so i set dhcpd server. and hostapd. But, If i use "sudo iwlist wlan scan" command , kernel is rebooting with panic.. how can i set hostapd.? It's my setting. /etc/hostapd.conf ctrl_interface=/var/run/hostapd ctrl_interface_group=0 macaddr_acl=0 auth_algs=1 ignore_broadcast_ssid=0 wpa=2 wpa_pairwise=TKIP rsn_pairwise=CCMP wpa_passphrase=12345678 driver=nl80211 wme_enabled=1 wpa_group_rekey=86400 interface=wlan0 hw_mode=g channel=6 ssid=TEST_AP /etc/network/interfaces allow-hotplug eth0 iface eth0 inet dhcp auto lo iface lo inet loopback allow-hotplug wlan0 iface wlan0 inet static address 192.168.150.1 netmask 255.255.255.0 /etc/dhcp/dhcpd.conf the last line add this contents subnet 192.168.150.0 netmask 255.255.255.0 { range 192.168.150.100 192.168. 150.199; option broadcast-address 192.168. 150.255; option routers 192.168.150.1; default-lease-time 600; max-lease-time 7200; option domain-name "local"; option domain-name-servers 8.8.8.8, 168.126.63.1; } thanks..

Hi i am using Orangepiplus and armbian 5.20 debian jessise. but i have problem. somtime it's stopped Point is => started LSB: set CPUFreq kernel parameters or => starting LSB: set CPUFreq kernel parameters, so i adjust boot clock using /boot/script.fex => boot_clock : 1080 -> 1180 and => boot_clock : 1080 -> 980 but it's failed. help me please. (i try to reboot command, 100sec (repeat))

Hello, my Orange PI Plus is no Wifi. when i give lsusb is it no wifi modul. Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 05e3:0718 Genesys Logic, Inc. IDE/SATA Adapter Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 003: ID 05ac:0256 Apple, Inc. Bus 002 Device 002: ID 1a40:0101 Terminus Technology Inc. 4-Port HUB Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Armbian and Lubuntu the same. any idea?

Hi, I am using orangepi+, i have a problem. My os version is Armbian_5.20_Orangepiplus_Debian_jessie_3.4.112_server. but, when i use reboot command, somtimes it's stopped, it's stop point is -> Starting LSB: set CPUFreq Kernel parameters... I don't know why it's stoped.. plz reply. Thanks.

Good afternoon dear experts. I have a problem on my Orange pi plus 2. My hard drive(WD Red WD10JFCX, 1Тб, HDD, SATA III, 2.5") is periodically switched-off (/dev/sda1). in ravines I have: Sep 28 10:48:37 PM dvr kernel: [1678371.474389] ehci_irq: highspeed device disconnect Sep 28 10:48:37 PM dvr kernel: [1678371.474593] usb 3-1: USB disconnect, device number 2 Sep 28 10:48:37 PM dvr kernel: [1678371.479539] Buffer I/O error on device sda1, logical block 76682192 Sep 28 10:48:37 PM dvr kernel: [1678371.479581] Buffer I/O error on device sda1, logical block 76682193 Sep 28 10:48:37 PM dvr kernel: [1678371.479609] Buffer I/O error on device sda1, logical block 76682194 Sep 28 10:48:37 PM dvr kernel: [1678371.479636] Buffer I/O error on device sda1, logical block 76682195 Sep 28 10:48:37 PM dvr kernel: [1678371.479663] Buffer I/O error on device sda1, logical block 76682196 Sep 28 10:48:37 PM dvr kernel: [1678371.479690] Buffer I/O error on device sda1, logical block 76682197 Sep 28 10:48:37 PM dvr kernel: [1678371.479716] Buffer I/O error on device sda1, logical block 76682198 and Sep 28 22:48:37 dvr kernel: [1678371.474593] usb 3-1: USB disconnect, device number 2 Sep 28 22:48:37 dvr kernel: [1678371.480406] EXT4-fs warning (device sda1): ext4_end_bio:249: I/O error writing to inode 55368747 (offset 1900544 size 126976 starting block 76682478) Sep 28 22:48:37 dvr kernel: [1678371.481086] EXT4-fs warning (device sda1): ext4_end_bio:249: I/O error writing to inode 55368747 (offset 2023424 size 73728 starting block 76682496) Sep 28 22:48:37 dvr kernel: [1678371.482205] EXT4-fs warning (device sda1): ext4_end_bio:249: I/O error writing to inode 55368747 (offset 2097152 size 126976 starting block 76683038) Sep 28 22:48:37 dvr kernel: [1678371.483168] EXT4-fs warning (device sda1): ext4_end_bio:249: I/O error writing to inode 55368747 (offset 2220032 size 126976 starting block 76683068) Sep 28 22:48:37 dvr kernel: [1678371.484271] EXT4-fs warning (device sda1): ext4_end_bio:249: I/O error writing to inode 55368747 (offset 2342912 size 126976 starting block 76683098) Sep 28 22:48:37 dvr kernel: [1678371.485228] EXT4-fs warning (device sda1): ext4_end_bio:249: I/O error writing to inode 55368747 (offset 2465792 size 126976 starting block 76683128) Sep 28 22:48:37 dvr kernel: [1678371.485968] EXT4-fs warning (device sda1): ext4_end_bio:249: I/O error writing to inode 55368747 (offset 2588672 size 126976 starting block 76683158) Sep 28 22:48:37 dvr kernel: [1678371.485968] EXT4-fs warning (device sda1): ext4_end_bio:249: I/O error writing to inode 55368747 (offset 2711552 size 126976 starting block 76683188) Sep 28 22:48:37 dvr kernel: [1678371.485968] EXT4-fs warning (device sda1): ext4_end_bio:249: I/O error writing to inode 55368747 (offset 2834432 size 126976 starting block 76683218) Sep 28 22:48:37 dvr kernel: [1678371.485968] EXT4-fs warning (device sda1): ext4_end_bio:249: I/O error writing to inode 55368747 (offset 2957312 size 61440 starting block 76683233) Sep 28 22:48:37 dvr kernel: [1678371.492144] EXT4-fs warning (device sda1): ext4_end_bio:249: I/O error writing to inode 55368748 (offset 860160 size 110592 starting block 76681453) Sep 28 22:48:37 dvr kernel: [1678371.493059] EXT4-fs warning (device sda1): ext4_end_bio:249: I/O error writing to inode 55368748 (offset 737280 size 126976 starting block 76681426) Sep 28 22:48:37 dvr kernel: [1678371.493944] EXT4-fs warning (device sda1): ext4_end_bio:249: I/O error writing to inode 55368748 (offset 614400 size 126976 starting block 76681396) Sep 28 22:48:37 dvr kernel: [1678371.494826] EXT4-fs warning (device sda1): ext4_end_bio:249: I/O error writing to inode 55368748 (offset 491520 size 126976 starting block 76681366) Sep 28 22:48:37 dvr kernel: [1678371.495733] EXT4-fs warning (device sda1): ext4_end_bio:249: I/O error writing to inode 55368748 (offset 368640 size 126976 starting block 76681336) Sep 28 22:48:37 dvr kernel: [1678371.496700] EXT4-fs warning (device sda1): ext4_end_bio:249: I/O error writing to inode 55368748 (offset 245760 size 126976 starting block 76681306) Sep 28 22:48:37 dvr kernel: [1678371.497596] EXT4-fs warning (device sda1): ext4_end_bio:249: I/O error writing to inode 55368748 (offset 122880 size 126976 starting block 76681276) Sep 28 22:48:37 dvr kernel: [1678371.498622] EXT4-fs warning (device sda1): ext4_end_bio:249: I/O error writing to inode 55368748 (offset 0 size 126976 starting block 76681246) Sep 28 22:48:37 dvr kernel: [1678371.499036] JBD2: Detected IO errors while flushing file data on sda1-8 Sep 28 22:48:40 dvr kernel: [1678373.960205] usb 3-1: new high-speed USB device number 3 using sunxi-ehci Sep 28 22:48:40 dvr kernel: [1678374.114545] scsi1 : usb-storage 3-1:1.0 Sep 28 22:48:40 dvr mtp-probe: checking bus 3, device 3: "/sys/devices/platform/sunxi-ehci.4/usb3/3-1" Sep 28 22:48:40 dvr mtp-probe: bus: 3, device: 3 was not an MTP device Sep 28 22:48:41 dvr kernel: [1678375.112846] scsi 1:0:0:0: Direct-Access WDC WD10 JFCX-68N6GN0 0009 PQ: 0 ANSI: 0 Sep 28 22:48:41 dvr kernel: [1678375.115159] sd 1:0:0:0: [sdb] 1953525164 512-byte logical blocks: (1.00 TB/931 GiB) Sep 28 22:48:41 dvr kernel: [1678375.116283] sd 1:0:0:0: [sdb] Write Protect is off Sep 28 22:48:41 dvr kernel: [1678375.155871] sdb: sdb1 Sep 28 22:48:41 dvr kernel: [1678375.160752] sd 1:0:0:0: [sdb] Attached SCSI disk Sep 29 06:42:28 dvr rsyslogd: [origin software="rsyslogd" swVersion="8.4.2" x-pid="1415" x-info="http://www.rsyslog.com"] rsyslogd was HUPed Sep 29 06:42:29 dvr rsyslogd: [origin software="rsyslogd" swVersion="8.4.2" x-pid="1415" x-info="http://www.rsyslog.com"] rsyslogd was HUPed Sep 29 22:50:02 dvr kernel: [1764856.800097] EXT4-fs (sda1): error count since last fsck: 5 Sep 29 22:50:02 dvr kernel: [1764856.800132] EXT4-fs (sda1): initial error at time 1475092117: ext4_journal_start_sb:328 Sep 29 22:50:02 dvr kernel: [1764856.800164] EXT4-fs (sda1): last error at time 1475125069: ext4_find_entry:941: inode 55312385 Orange pi plus 2 works 24 hours a day, 7 days a week, on the hard drive constant record of small videos of files has to be made. Help to solve a problem please.

Hi, I am using Armbian_5.20_Orangepiplus_Debian_jessie_3.4.112.img with emmc nand flash. I want to make .img file for emmc nand flash. because i am plan to use Phoenixsuit tool.. how can i make emmc nand flash image file? please help me.. thanks.

Hi, I'm Olivier, french engineer, and i have bought an orangepi plus card in april. I use linux (x86) since 1994 Sorry for my bad english ... I was happy to find Armbian because linux images provided by xunlong have many security problems (example / and all system directory aren't owned by root but by orangepi user). Thank for your work on Armbian. My Orangepi + has been installed with a 5.10 armbian image (Armbian_5.10_Orangepiplus_Debian_jessie_3.4.112) and run perfectly. I wanted upgrade to 5.20 and since the card doesn't boot anymore. I can boot with the native android on NAND memory but I can't boot on SDcard. When I boot on sdcard, only green led is on (not red led) and I don't have any display on my HDMI screen. I can restore my sdcard image back up with v5.10 and boot again, the card is OK for me. I followed the upgrade documentation to pass from v5.10 to v5.20 : apt-get update apt-get upgrade apt-get install -f apt-get upgrade apt-get autoremove -y and i had an error message during first apt-get upgrade : /boot/initrd.img-3.4.112-sun8i does not exist. Cannot update. I can mount the sdcard on my linux box (an archlinux) and list directories without problem : on my sdcard image backup (v5.10), in /boot I have : Any idea ? here is the all message of upgrade process :

Hi. My platform is Orange Pi Plus. I connected SATA HDD and installed Armbian. Using nand-sata-install I created the following scenario: boot from SD, system on SATA. I also installed lighttpd. Several days everything works fine and than: ...file system on the root filesystem failed … rebooting automatically due to panic= boot argument... After that the PC just reboots constantly and I can do anything. The only solution I found is to repeat the process of boot SD creation. But after that I need to install everything again. All this I already did for several times... What maybe the reason of this error? Can I exclude the SD card and use eMMC instead? Is there anything I can try in this situation? Thanks.

Hi dear. I have some question about orangepi plus. I am using orangepi+ and The latest Armbian Debian Version was installed in emmc. and i have some BLE Module. but, when i add my module to gpio pin, i can see I/O Error..but it's not always, somtimes there is no error. and when i boot orangepi-plus, it is PULL-UP state. i don't know this reason, how can change default gpio pull-up or pull-down state? or you have some idea? thanks

Hello, I'm trying to boot an Orange Pi Plus with Armbian 5.20, and it does not work. I've already check that both OPi and my sdcard work fine, because I can flash and boot the images on orangepi.org site. Besides, I checked how u-boot starts with both Armbian and "debian server" orangepi.org image (both attached)

Hello, I have an Orange Pi+ 2 and Orange Pi+ 2e. I use Armbian, updated to 5.20 with these commands: sudo apt-get update sudo apt-get upgrade so I rebooted and can't start. What can I do? Thanks

First of all ('Boring' alert!): outstanding job with the new updates. It must be lonely at the top. Kudos! Then (just curious!): is there any particular reason known that the amount of memory is an issue for GLshim? Then secondly: I do have an orange pi + (H3, 1 GB memory, Mali400)... according to the changelog GLShim is not in... For me it does not make sense... Regards, Makama80

Hi, I'm Rosario and I'm a new Armbian follower. I liked it. After months using my OPI Plus2 with Ubuntu Jessie Loboris image (and installed it also on emmc) I decided to install Armbian. I need to say last time I installed OS on emmc I received an error. Erase was fine but copy of last jessie Image no. After that I Installed Armbian Image with no problem and after some reboot OS run up fine. I downloaded last Armbian Image (3.4.112 kernel version). Now, when I try to use emmc I receive some error. First of all seems it's missing. I see only mmcblko (my SD card). emmc doesn't exists: root@orangepiplus:~# cat /proc/partitions major minor #blocks name 179 0 60530688 mmcblk0 179 1 60529664 mmcblk0p1 Running nand-sata-install.sh I receive error saying No emmc found. I connected UART cable to see if POST log error. Seems emmc is OK but I don't know why kernel doesn't use it. Attached Some UART log. Can someone help to understand if emmc is broken or I'm wrong in some point. Thanks in advance OrangePIPlus2-UART.txt

Hi Harness the Board Orange Pi + 2. I propose to add the configuration for it. sasha@ubuntu:~/orange/sdk/lib$ git diff master..add-orangepiplus2 diff --git a/config/boards/orangepiplus2.conf b/config/boards/orangepiplus2.conf new file mode 100644 index 0000000..5d37e8c --- /dev/null +++ b/config/boards/orangepiplus2.conf @@ -0,0 +1,11 @@ +# H3 quad core 2GB RAM WiFi eMMC +BOARD_NAME="Orange Pi+ 2" +LINUXFAMILY=sun8i +BOOTCONFIG=orangepi_plus_defconfig +MODULES="8189es #gpio_sunxi #w1-sunxi #w1-gpio #w1-therm #gc2035 #vfe_v4l2 #sunxi-cir" +MODULES_NEXT="8189es" +CPUMIN=480000 +CPUMAX=1296000 +CLI_TARGET="jessie:default" +DESKTOP_TARGET="jessie:default" +KERNEL_TARGET="default,dev" diff --git a/scripts/armbianmonitor/armbianmonitor-daemon b/scripts/armbianmonitor/armbianmonitor-daemon index 0dfaa6b..813bafa 100644 --- a/scripts/armbianmonitor/armbianmonitor-daemon +++ b/scripts/armbianmonitor/armbianmonitor-daemon @@ -100,7 +100,7 @@ Main() { DealWithNewBoard # DealWithiMX6 ;; - "Orange Pi PC"|"Orange Pi Plus"|"Orange Pi 2"|"Orange Pi One"|"Orange Pi Lite") + "Orange Pi PC"|"Orange Pi+"|"Orange Pi+ 2"|"Orange Pi 2"|"Orange Pi One"|"Orange Pi Lite") DealWithNewBoard # DealWithH3 ;;

Hi everybody, I have an OPI+ and gc2035 camera module, i try camera with "motion" according to this tutorial and getting one picture on localhost:8081, after this page display "problem loading page". however, This is not the main issue. i try to get picture with gstreamer and i see following errors: libv4l2: error setting pixformat: operation not permitted ERROR: from element /GstPipeline:pipeline0/GstV4l2Src:v4l2src: Device '/dev/video0' cannot capture at 1600x1200 Call to S_FMT failed for YU12 @ 1600x1200: Operation not permitted. My gstreamer pipeline is: gst-launch v4l2src always-copy=false ! 'video/x-raw-yuv, format=(fourcc)I420, width=1600, height=1200' ! ffmpegcolorspace ! ximagesink I try other resolution but get the same error. vlc player display correct stream with following command: cvlc v4l2:///dev/video0 if problem is v4l2 so why vlc display camera stream? #uname -a Linux orangepiplus 3.4.112-sun8i #14 SMP PREEMPT Tue Jul 5 16:28:14 CEST 2016 armv7l GNU/Linux thanks in advance best regards