oolonthegreat Posted August 15, 2022 Posted August 15, 2022 hiya folks! I have a no-brand (MK - 918?) RK3188 Android TV box that I'm trying to install Armbian, but I can't get it to boot Multiboot nor the Armbian image from the SD card. I have tried different SD cards and USB sticks, I am burning the Multitool image with balenaEtcher, but no luck, it boots straight to Android. I have also tried the solution posted by fabiobassa but the program gets stuck on "Downloading bootloader...". here's some more info: ➜ lsusb Bus 001 Device 009: ID 2207:310b Fuzhou Rockchip Electronics Company RK3188 in Mask ROM mode ➜ sudo ./rkdeveloptool ld DevNo=1 Vid=0x2207,Pid=0x310b,LocationID=102 Loader ➜ sudo ./rkdeveloptool rd 3 Reset Device OK. ➜ sudo ./rkdeveloptool ld DevNo=1 Vid=0x2207,Pid=0x310b,LocationID=102 Maskrom ➜ sudo ./rkdeveloptool db MiniLoaderAll.bin Downloading bootloader... it gets stuck there no matter how long I wait. also, I have soldered the UART debug connections and here is the output I get when it boots to its default Android: Spoiler DDR Version 1.04 20140217 In DDR3 300MHz Bus Width=32 Col=10 Bank=8 Row=16 CS=1 Die Bus-Width=8 Size=2048MB Memory OK OUT BUILD=====2 No.1 FLASH ID:2c 64 44 4b a9 0 OK! 214381 unsigned! SecureBootEn = 0 0 Boot ver: 2014-03-03#2.13 start_linux=====219791 729482 Starting kernel...@0x60408000 Uncompressing Linux... done, booting the kernel. [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.0.36+ (wasser19641@gmail.com) (gcc version 4.7 (GCC) ) #306 SMP PREEMPT Sun Oct 12 11:26:31 CEST 2014 [ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: RK30board [ 0.000000] ddr size = 2048 M, set ion_reserve_size size to 125829120 [ 0.000000] memory reserve: Memory(base:0x98800000 size:120M) reserved for <ion> [ 0.000000] memory reserve: Memory(base:0x97000000 size:24M) reserved for <fb0 buf> [ 0.000000] memory reserve: Total reserved 144M [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] CPU SRAM: copied sram code from c0f19000 to fef00100 - fef020c0 [ 0.000000] CPU SRAM: copied sram data from c0f1afc0 to fef020c0 - fef029e4 [ 0.000000] sram_log: @ 0q @ P 1 / ! aB@ 2 `" 2q : 4q [ 0.000000] CLKDATA_MSG: pll_flag = 0x03 [ 0.000000] cpll auto set rate error [ 0.000000] L310 cache controller enabled [ 0.000000] l2x0: 16 ways, CACHE_ID 0x4100c0c8, AUX_CTRL 0x76050001, Cache size: 524288 B [ 0.000000] DDR DEBUG: version 1.00 20131106 [ 0.000000] DDR DEBUG: DDR3 Device [ 0.000000] DDR DEBUG: Bus Width=32 Col=10 Bank=8 Row=16 CS=1 Total Capability=2048MB [ 0.000000] DDR DEBUG: init success!!! freq=300MHz [ 0.000000] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=0x4, DGSL=1 extra clock, DGPS=90 [ 0.000000] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=0x4, DGSL=1 extra clock, DGPS=90 [ 0.000000] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=0x4, DGSL=1 extra clock, DGPS=90 [ 0.000000] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=0x4, DGSL=1 extra clock, DGPS=90 [ 0.000000] DDR DEBUG: ZERR=0, ZDONE=0, ZPD=0x0, ZPU=0x0, OPD=0x0, OPU=0x0 [ 0.000000] DDR DEBUG: DRV Pull-Up=0xb, DRV Pull-Dwn=0xb [ 0.000000] DDR DEBUG: ODT Pull-Up=0x2, ODT Pull-Dwn=0x2 [ 0.000000] PERCPU: Embedded 7 pages/cpu @c315d000 s6976 r8192 d13504 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 483328 [ 0.000000] Kernel command line: console=ttyFIQ0 androidboot.console=ttyFIQ0 init=/init initrd=0x62000000,0x00150000 mtdparts=rk29xxnand:0x00002000@0x00002000(misc),0x00006000@0x00004000( kernel),0x00006000@0x0000a000(boot),0x00010000@0x00010000(recovery),0x00020000@0x00020000(backup),0x00040000@0x00040000(cache),0x00002000@0x00080000(metadata),0x00002000@0x00082000(kpanic),0 x00272000@0x00084000(system),-@0x002F6000(userdata) bootver=2014-03-03#2.13 firmware_ver=4.4.2 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] allocated 8388608 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 880MB 1024MB = 1904MB total [ 0.000000] Memory: 1901376k/1901376k available, 195776k reserved, 1449984K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] DMA : 0xff600000 - 0xffe00000 ( 8 MB) [ 0.000000] vmalloc : 0xdf000000 - 0xfe800000 ( 504 MB) [ 0.000000] lowmem : 0xc0000000 - 0xde800000 ( 488 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .init : 0xc0408000 - 0xc062f000 (2204 kB) [ 0.000000] .text : 0xc062f000 - 0xc0e840a4 (8533 kB) [ 0.000000] .data : 0xc0e86000 - 0xc0f18b28 ( 587 kB) [ 0.000000] .bss : 0xc0f1c024 - 0xc194e328 (10441 kB) [ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:352 [ 0.000000] rk30_gpio_init: 128 gpio irqs in 4 banks [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms [ 0.000000] rk_timer: version 1.3 [ 0.003739] Calibrating delay loop (skipped) preset value.. 1583.48 BogoMIPS (lpj=7917420) [ 0.012874] pid_max: default: 32768 minimum: 301 [ 0.018146] Security Framework initialized [ 0.022778] Mount-cache hash table entries: 512 [ 0.028362] Initializing cgroup subsys debug [ 0.033124] Initializing cgroup subsys cpuacct [ 0.038099] Initializing cgroup subsys memory [ 0.042972] Initializing cgroup subsys freezer [ 0.047945] CPU: Testing write buffer coherency: ok [ 0.134208] CPU1: Booted secondary processor [ 0.174205] CPU2: Booted secondary processor [ 0.214201] CPU3: Booted secondary processor [ 0.214239] Brought up 4 CPUs [ 0.231840] SMP: Total of 4 processors activated (6333.93 BogoMIPS). [ 0.239190] devtmpfs: initialized [ 0.249141] NET: Registered protocol family 16 [ 0.254488] DVFS MSG: AVS Value(index=0): 128 128 128 128 128 128 127 127 127 128 [ 0.273374] lcdc0 is used as external display device contoller! [ 0.279957] lcdc1 is used as primary display device controller! [ 0.386728] rk29sdk_wifi_bt_gpio_control_init: init finished <hit enter to activate fiq debugger> 0.394297] console [ttyFIQ0] enabled, bootconsole disabled [ 0.394297] console [ttyFIQ0] enabled, bootconsole disabled [ 0.403307] Registered FIQ tty driver de0adc00 [ 0.403891] Loaded driver for PL330 DMAC-1 rk29-pl330 [ 0.403906] DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12 [ 0.404054] Loaded driver for PL330 DMAC-2 rk29-pl330 [ 0.404068] DBUFF-64x8bytes Num_Chans-7 Num_Peri-20 Num_Events-14 [ 0.435947] bio: create slab <bio-0> at 0 [ 0.440353] SCSI subsystem initialized [ 0.440538] usbcore: registered new interface driver usbfs [ 0.440629] usbcore: registered new interface driver hub [ 0.454906] usbcore: registered new device driver usb [ 0.455280] rk30_i2c rk30_i2c.0: i2c-0: RK30 I2C adapter [ 0.455500] rk30_i2c rk30_i2c.1: i2c-1: RK30 I2C adapter [ 0.455666] rk30_i2c rk30_i2c.2: i2c-2: RK30 I2C adapter [ 0.455769] rk30_i2c rk30_i2c.3: i2c-3: RK30 I2C adapter [ 0.455871] rk30_i2c rk30_i2c.4: i2c-4: RK30 I2C adapter [ 0.486460] rk30-adc rk30-adc: rk30 adc: driver initialized [ 0.486529] RK29 Watchdog Timer, (c) 2011 Rockchip Electronics [ 0.486695] rk29-wdt rk29-wdt.0: starting watchdog timer [ 0.486933] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 0.487339] Bluetooth: Core ver 2.16 [ 0.487390] NET: Registered protocol family 31 [ 0.487401] Bluetooth: HCI device and connection manager initialized [ 0.487416] Bluetooth: HCI socket layer initialized [ 0.487428] Bluetooth: L2CAP socket layer initialized [ 0.487452] Bluetooth: SCO socket layer initialized [ 0.488489] rk fb probe ok! [ 0.493184] act8846_set_init,line=17 [ 0.493196] act8846_set_init:g_pmic_type=3 [ 0.494867] act8846_set_init act_dcdc1 =1200000mV end [ 0.496622] act8846_set_init vdd_core =1000000mV end [ 0.498373] act8846_set_init vdd_cpu =1000000mV end [ 0.500123] act8846_set_init act_dcdc4 =3300000mV end [ 0.501277] act8846_set_init act_ldo1 =1000000mV end [ 0.502928] act8846_set_init act_ldo2 =1200000mV end [ 0.504580] act8846_set_init act_ldo3 =1800000mV end [ 0.506231] act8846_set_init act_ldo4 =3300000mV end [ 0.507881] act8846_set_init act_ldo5 =3300000mV end [ 0.509530] act8846_set_init act_ldo6 =3300000mV end [ 0.510581] act8846_set_init act_ldo7 =1800000mV end [ 0.512230] act8846_set_init act_ldo8 =2800000mV end [ 0.512248] act8846_set_init,line=78 END [ 0.512293] i2c-core: driver [act8846] using legacy suspend method [ 0.512305] i2c-core: driver [act8846] using legacy resume method [ 0.512345] rk1000_control_probe [ 0.537236] rk1000_control_probe ok [ 0.537296] Switching to clocksource rk_timer [ 0.543569] Switched to NOHz mode on CPU #0 [ 0.544242] Switched to NOHz mode on CPU #3 [ 0.544249] Switched to NOHz mode on CPU #1 [ 0.544257] Switched to NOHz mode on CPU #2 [ 0.544596] lcdc1:reg_phy_base = 0x1010e000,reg_vir_base:0xdf02c000 [ 0.544638] fb0:win0 [ 0.544641] fb1:win1 [ 0.544644] fb2:win2 [ 0.544702] rk3188 lcdc1 clk enable... [ 0.569778] rk3188 lcdc1 clk disable... [ 0.628074] fb0:phy:97000000>>vir:e0000000>>len:0x1800000 [ 0.628315] rk_fb_register>>>>>fb0 [ 0.628609] rk_fb_register>>>>>fb1 [ 0.661086] rk3188 lcdc1 probe ok! [ 0.661161] lcdc0:reg_phy_base = 0x1010c000,reg_vir_base:0xdf040000 [ 0.661212] fb0:win0 [ 0.661215] fb1:win1 [ 0.661218] fb2:win2 [ 0.661282] rk3188 lcdc0 clk enable... [ 0.686354] rk3188 lcdc0 clk disable... [ 0.686370] fb2:phy:97000000>>vir:e0000000>>len:0x1800000 [ 0.686599] rk_fb_register>>>>>fb2 [ 0.686890] rk_fb_register>>>>>fb3 [ 0.686902] rk3188 lcdc0 probe ok! [ 0.724681] cfg80211: Calling CRDA to update world regulatory domain [ 0.747766] IT66121 probe success. [ 0.751140] NET: Registered protocol family 2 [ 0.751258] IP route cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.751566] TCP established hash table entries: 65536 (order: 7, 524288 bytes) [ 0.752541] TCP bind hash table entries: 65536 (order: 7, 786432 bytes) [ 0.753961] TCP: Hash tables configured (established 65536 bind 65536) [ 0.753974] TCP reno registered [ 0.753986] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.754011] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.754284] NET: Registered protocol family 1 [ 0.802608] RPC: Registered named UNIX socket transport module. [ 0.802625] RPC: Registered udp transport module. [ 0.802634] RPC: Registered tcp transport module. [ 0.802644] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.802808] Unpacking initramfs... [ 0.868861] Freeing initrd memory: 1344K [ 0.868953] PMU: registered new PMU device of type 0 [ 0.869065] efuse_version_val: efuse version = 51 [ 0.869080] DVFS MSG: core: dvfs_adjust_table_lmtvolt get leakage_level = 17000 [ 0.869094] adjust table freq=1608000 KHz, index=1350000 mV to index=1250000 mV [ 0.869109] efuse_version_val: efuse version = 51 [ 0.869120] DVFS MSG: aclk_gpu: dvfs_adjust_table_lmtvolt get leakage_level = 17000 [ 0.869942] cpufreq: delete arm freq(1608000) [ 0.913975] rk3188 cpufreq version 2.2, suspend freq 816 MHz [ 0.914192] vpu: power on [ 0.914240] VPU_SERVICE: checking hw id 4831 [ 0.926842] vpu: power off...done [ 0.926878] VPU_SERVICE: init success [ 0.927132] audit: initializing netlink socket (disabled) [ 0.927169] type=2000 audit(0.860:1): initialized [ 0.944065] highmem bounce pool size: 64 pages [ 0.944244] ashmem: initialized [ 0.954959] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.955209] NTFS driver 2.1.30 [Flags: R/W]. [ 0.955369] fuse init (API version 7.16) [ 0.970386] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.970398] io scheduler noop registered [ 0.970404] io scheduler deadline registered [ 0.970448] io scheduler cfq registered (default) [ 0.990722] rga: Driver loaded succesfully [ 0.990848] rk_serial.c v1.6 2013-12-23 [ 0.990907] rk_serial.0: ttyS0 at MMIO 0x10124000 (irq = 66) is a rk29_serial.0 [ 0.990993] rk_serial rk_serial.0: membase 0xdf048000 [ 0.991038] rk_serial.3: ttyS3 at MMIO 0x20068000 (irq = 69) is a rk29_serial.3 [ 0.991124] rk_serial rk_serial.3: membase 0xdf050000 [ 0.991276] Rockchip ion module(version: 1.0) is successfully loaded [ 0.992798] loop: module loaded [ 0.992827] Android kernel panic handler initialized (bind=kpanic) [ 0.993272] PPP generic driver version 2.4.2 [ 0.993361] PPP Deflate Compression module registered [ 0.993368] PPP BSD Compression module registered [ 1.053173] PPP MPPE Compression module registered [ 1.053184] NET: Registered protocol family 24 [ 1.053193] tun: Universal TUN/TAP device driver, 1.6 [ 1.053198] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 1.053354] usbcore: registered new interface driver sr9700_android [ 1.053372] Rockchip WiFi SYS interface (V1.00) ... [ 1.053403] Initializing USB Mass Storage driver... [ 1.053445] usbcore: registered new interface driver usb-storage [ 1.053452] USB Mass Storage support registered. [ 1.053528] usbcore: registered new interface driver usbserial [ 1.053553] USB Serial support registered for generic [ 1.053581] usbcore: registered new interface driver usbserial_generic [ 1.053588] usbserial: USB Serial Driver core [ 1.053609] USB Serial support registered for GSM modem (1-port) [ 1.053640] usbcore: registered new interface driver option [ 1.053646] option: v0.7.2:USB Driver for GSM modems [ 1.053668] USB Serial support registered for usi-modem [ 1.053701] usbcore: registered new interface driver usi-modem [ 1.275256] DWC_OTG: ^^^^^^^^^^^^^^^^^^Host Mode [ 1.275274] usb20_otg usb20_otg: DWC OTG Controller [ 1.275362] usb20_otg usb20_otg: new USB bus registered, assigned bus number 1 [ 1.275389] usb20_otg usb20_otg: irq 48, io mem 0x00000000 [ 1.275418] DWC_OTG: Init: Port Power? op_state=1 [ 1.275424] DWC_OTG: Init: Power Port (0) [ 1.275467] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.275476] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.275484] usb usb1: Product: DWC OTG Controller [ 1.275491] usb usb1: Manufacturer: Linux 3.0.36+ dwc_otg_hcd [ 1.275497] usb usb1: SerialNumber: usb20_otg [ 1.275749] hub 1-0:1.0: USB hub found [ 1.275763] hub 1-0:1.0: 1 port detected [ 1.278310] DWC_OTG: host20_driver_probe host2.0 reg addr: 0x101c0000 remap:0xdf100000 [ 1.488642] DWC_OTG: ^^^^^^^^^^^^^^^^^^Host Mode [ 1.488663] usb20_host usb20_host: DWC OTG Controller [ 1.488690] usb20_host usb20_host: new USB bus registered, assigned bus number 2 [ 1.488718] usb20_host usb20_host: irq 49, io mem 0x00000000 [ 1.488758] DWC_OTG: Init: Port Power? op_state=1 [ 1.488764] DWC_OTG: Init: Power Port (0) [ 1.488797] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.488806] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.488814] usb usb2: Product: DWC OTG Controller [ 1.488820] usb usb2: Manufacturer: Linux 3.0.36+ host20_hcd [ 1.488826] usb usb2: SerialNumber: usb20_host [ 1.489059] hub 2-0:1.0: USB hub found [ 1.489071] hub 2-0:1.0: 1 port detected [ 1.489398] DWC_OTG: Mode Mismatch Interrupt: currently in Host mode [ 1.562864] android_usb gadget: Mass Storage Function, version: 2009/09/11 [ 1.562874] android_usb gadget: Number of LUNs=2 [ 1.562883] lun0: LUN: removable file: (no medium) [ 1.562889] lun1: LUN: removable file: (no medium) [ 1.563082] android_usb gadget: android_usb ready [ 1.563245] input: rk29-keypad as /devices/platform/rk29-keypad/input/input0 [ 1.563402] usbcore: registered new interface driver xpad [ 1.563566] remotectl probe j=0x0 [ 1.563574] remotectl probe j=0x1 [ 1.563579] remotectl probe j=0x2 [ 1.563583] remotectl probe j=0x3 [ 1.563588] remotectl probe j=0x4 [ 1.563592] remotectl probe j=0x5 [ 1.563597] remotectl probe j=0x6 [ 1.563602] remotectl probe j=0x7 [ 1.563691] input: rkxx-remotectl as /devices/platform/rkxx-remotectl/input/input1 [ 1.565772] rtc_hym8563 1-0051: clock/calendar information is no longer guaranteed [ 1.568421] using rtc device, rtc_hym8563, for alarms [ 1.568445] rtc_hym8563 1-0051: rtc core: registered rtc_hym8563 as rtc0 [ 1.568476] i2c /dev entries driver [ 1.568901] lirc_dev: IR Remote Control driver registered, major 250 [ 1.568910] IR NEC protocol handler initialized [ 1.568916] IR RC5(x) protocol handler initialized [ 1.568921] IR RC6 protocol handler initialized [ 1.568926] IR JVC protocol handler initialized [ 1.568932] IR Sony protocol handler initialized [ 1.568937] IR RC5 (streamzap) protocol handler initialized [ 1.568942] IR LIRC bridge handler initialized [ 1.568947] Linux video capture interface: v2.00 [ 1.569003] usbcore: registered new interface driver uvcvideo [ 1.569010] USB Video Class driver (v1.1.0) [ 1.569042] def_ref_volt: 1800mV, curr_ref_volt: 1800mV [ 1.569563] device-mapper: uevent: version 1.0.3 [ 1.569757] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com [ 1.569898] Bluetooth: HCI UART driver ver 2.2 [ 1.569906] Bluetooth: HCI H4 protocol initialized [ 1.569913] Bluetooth: HCI Realtek H5 protocol initialized [ 1.569920] Bluetooth: Generic Bluetooth SDIO driver ver 0.1 [ 1.569979] cpuidle: using governor ladder [ 1.569985] cpuidle: using governor menu [ 1.615329] [ 1.615331] drivers/mmc/core/core.c...2019.. ===== mmc_rescan Begin....[mmc0] [ 1.620398] rk29_sdmmc_change_clk_div..1684.. newDiv=62, newCLK=299Khz [sd_mmc] [ 1.620433] .Line4018..The End of SDMMC-probe Ver.6.07 The last modify date is 2013-12-20. [sd_mmc] [ 1.620567] .Line4018..The End of SDMMC-probe Ver.6.07 The last modify date is 2013-12-20. [sdio] [ 1.621915] usbcore: registered new interface driver usbhid [ 1.621923] usbhid: USB HID core driver [ 1.622178] logger: created 256K log 'log_main' [ 1.622234] logger: created 256K log 'log_events' [ 1.622292] logger: created 256K log 'log_radio' [ 1.622344] logger: created 256K log 'log_system' [ 1.622621] zram: Created 1 device(s) ... [ 1.623026] i2c-core: driver [RK1000_CODEC] using legacy suspend method [ 1.623034] i2c-core: driver [RK1000_CODEC] using legacy resume method [ 1.667150] [ 1.667152] mmc_attach_sd..1230.. ===== Begin to identify card as SD-card. [mmc0] [ 1.778346] rk29_sdmmc_change_clk_div..1684.. newDiv=0, newCLK=37125Khz [sd_mmc] [ 1.778393] mmc0: new high speed SDHC card at address 0001 [ 1.778613] mmcblk0: mmc0:0001 SD32G 29.1 GiB [ 1.780023] [ 1.780025] msdos_partition..466... ==== Begin to parse sdcard-partition. [mmcblk0] [ 1.780036] msdos_partition..535... ==== The sdcard has MBR. [mmcblk0] [ 1.780044] msdos_partition..548... ==== partition-1, size=1981MB. [mmcblk0] [ 1.780052] msdos_partition..576... ==== main partition-1....[mmcblk0] [ 1.780061] msdos_partition..548... ==== partition-2, size=51MB. [mmcblk0] [ 1.780069] msdos_partition..576... ==== main partition-2....[mmcblk0] [ 1.780076] mmcblk0: p1 p2 [ 1.780427] sdmmc_rescan_try_freq..1913.. ===== Initialize SD-card successfully. [mmc0] [ 1.780445] [ 1.780446] drivers/mmc/core/core.c...2019.. ===== mmc_rescan Begin....[mmc1] [ 1.781749] register rk1000 codec earlysuspend ok [ 1.781763] RK1000_CODEC 0-0060: Failed to add route Left DAC->Left Mixer [ 1.788208] asoc: rk1000_codec <-> rk29_i2s.1 mapping ok [ 1.788491] ALSA device list: [ 1.788498] #0: RK29_RK1000 [ 1.788593] GACT probability NOT on [ 1.788603] Mirror/redirect action on [ 1.788610] u32 classifier [ 1.788614] Actions configured [ 1.788620] Netfilter messages via NETLINK v0.30. [ 1.788664] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 1.788925] ctnetlink v0.93: registering with nfnetlink. [ 1.788955] NF_TPROXY: Transparent proxy support initialized, version 4.1.0 [ 1.788962] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd. [ 1.789198] xt_time: kernel timezone is -0000 [ 1.789318] ip_tables: (C) 2000-2006 Netfilter Core Team [ 1.789441] arp_tables: (C) 2002 David S. Miller [ 1.789479] TCP cubic registered [ 1.789485] Initializing XFRM netlink socket [ 1.789837] NET: Registered protocol family 10 [ 1.790375] Mobile IPv6 [ 1.790400] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 1.790507] IPv6 over IPv4 tunneling driver [ 1.791071] NET: Registered protocol family 17 [ 1.791095] NET: Registered protocol family 15 [ 1.791275] Bluetooth: RFCOMM TTY layer initialized [ 1.791290] Bluetooth: RFCOMM socket layer initialized [ 1.791297] Bluetooth: RFCOMM ver 1.11 [ 1.791303] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 1.791311] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 1.791435] NET: Registered protocol family 35 [ 1.791511] [BT_RFKILL]: Enter rfkill_rk_init [ 1.791587] [BT_RFKILL]: Request irq for bt wakeup host [ 1.791607] [BT_RFKILL]: ** disable irq [ 1.791679] [BT_RFKILL]: bt shut off power [ 1.797375] rk29_sdmmc_change_clk_div..1684.. newDiv=42, newCLK=294Khz [sdio] [ 1.820413] [BT_RFKILL]: bt_default device registered. [ 1.820459] Registering the dns_resolver key type [ 1.820490] pmic set pm_suspend_volt: [ 1.820502] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 1.820524] Registering SWP/SWPB emulation handler [ 1.820929] ddrfreq: verion 3.2 20131126 [ 1.820937] ddrfreq: fix cpu pause bug [ 1.820944] ddrfreq: normal 456MHz video 0MHz video_low 0MHz dualview 0MHz idle 0MHz suspend 0MHz reboot 300MHz [ 1.821254] rk3188 lcdc0 clk enable... [ 1.821269] lcdc0: dclk:148500000>>fps:60 [ 1.821279] rk30-lcdc rk30-lcdc.0: rk3188_load_screen for lcdc0 ok! [ 1.821769] ddrfreq: change freq to 445 MHz when normal [ 1.821917] lcdc0: dclk:27000000>>fps:60 [ 1.824077] rk30-lcdc rk30-lcdc.0: rk3188_load_screen for lcdc0 ok! [ 1.824086] lcdc0 wakeup from standby! [ 1.824092] lcdc0 win0 open,atv layer:1 [ 1.824103] lcdc0 win1 closed,atv layer:1 [ 1.824110] rk1000_tv ver 2.0 probe ok [ 1.824915] rtc_hym8563 1-0051: setting system clock to 2011-01-01 12:00:00 UTC (1293883200) [ 1.827599] asoc: dit-hifi <-> rk-spdif mapping ok [ 1.828013] usbcore: registered new interface driver snd-usb-audio [ 1.828306] Freeing init memory: 2204K [ 1.877422] usb 2-1: new high speed USB device number 2 using usb20_host [ 2.087923] usb 2-1: New USB device found, idVendor=1a40, idProduct=0101 [ 2.087935] usb 2-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 2.087943] usb 2-1: Product: USB 2.0 Hub [ 2.088278] hub 2-1:1.0: USB hub found [ 2.088417] hub 2-1:1.0: 4 ports detected [ 2.197836] init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_score_adj instead. [ 2.387409] usb 2-1.4: new full speed USB device number 3 using usb20_host [ 2.508029] usb 2-1.4: New USB device found, idVendor=0fe6, idProduct=9700 [ 2.508040] usb 2-1.4: New USB device strings: Mfr=0, Product=2, SerialNumber=0 [ 2.508049] usb 2-1.4: Product: USB 2.0 10/100M Ethernet Adaptor [ 2.547625] sr9700_android 2-1.4:1.0: eth0: register 'sr9700_android' at usb-usb20_host-1.4, SR9700_ANDROID USB Ethernet, 00:e0:4c:53:44:58 [ 2.662466] init: /dev/hw_random not found [ 2.662539] keychord: using input dev rk29-keypad for fevent [ 2.662549] keychord: using input dev rkxx-remotectl for fevent [ 3.141834] gp_rknand_info = : 0xde248400 [ 3.141913] rk30_chip_set:1 [ 3.141968] FtlInit! [ 3.141987] No.1 FLASH ID:2c 64 44 4b a9 0 [ 3.141997] No.2 FLASH ID:f0 ff ff ff ff ff [ 3.143548] FTL version: 5.0.12 20140214 [ 3.264695] gBootMedia = 1 gSdmmcFwPartOffset =0! [ 3.264706] rknand_buffer.c version: 4.40 20130830! [ 3.274330] 10 cmdlinepart partitions found on MTD device rk29xxnand [ 3.274340] Creating 10 MTD partitions on "rk29xxnand": [ 3.274351] 0x000000400000-0x000000800000 : "misc" [ 3.291096] 0x000000800000-0x000001400000 : "kernel" [ 3.296462] 0x000001400000-0x000002000000 : "boot" [ 3.301635] 0x000002000000-0x000004000000 : "recovery" [ 3.307154] 0x000004000000-0x000008000000 : "backup" [ 3.312514] 0x000008000000-0x000010000000 : "cache" [ 3.317789] 0x000010000000-0x000010400000 : "metadata" [ 3.323336] 0x000010400000-0x000010800000 : "kpanic" [ 3.329066] apanic: Bound to mtd partition 'kpanic' [ 3.329076] apanic: No panic data available [ 3.329087] 0x000010800000-0x00005ec00000 : "system" [ 3.343468] 0x00005ec00000-0x0001df400000 : "userdata" [ 3.350774] fs_mgr: parse_link_device : path = NULL [ 3.355514] fs_mgr: parse_link_device : path = NULL [ 3.360411] fs_mgr: parse_link_device : path = NULL [ 3.365303] fs_mgr: parse_link_device : path = NULL [ 3.370195] fs_mgr: parse_link_device : path = NULL [ 3.375087] fs_mgr: parse_link_device : path = NULL [ 3.379983] fs_mgr: parse_link_device : path = NULL [ 3.384875] fs_mgr: parse_link_device : path = NULL [ 3.389785] fs_mgr: ---------------resize_fs blk_dev /dev/block/mtd/by-name/system, type ext4 [ 3.398308] fs_mgr: Running /sbin/resize2fs on /dev/block/mtd/by-name/system [ 3.406809] resize2fs: resize2fs 1.41.14 (22-Dec-2010) [ 3.414696] resize2fs: The filesystem is already 320512 blocks long. Nothing to do! [ 3.414712] resize2fs: [ 3.427850] EXT4-fs (mtdblock8): mounted filesystem with ordered data mode. Opts: noauto_da_alloc,discard [ 3.446810] EXT4-fs (mtdblock5): recovery complete [ 3.446927] EXT4-fs (mtdblock5): mounted filesystem with ordered data mode. Opts: noauto_da_alloc,discard [ 3.463029] EXT4-fs (mtdblock6): warning: mounting unchecked fs, running e2fsck is recommended [ 3.463187] EXT4-fs (mtdblock6): mounted filesystem without journal. Opts: noauto_da_alloc,discard [ 3.618620] EXT4-fs (mtdblock9): recovery complete [ 3.618734] EXT4-fs (mtdblock9): mounted filesystem with ordered data mode. Opts: noauto_da_alloc,discard [ 3.639752] UMP: Using OS memory backend, allocation limit: 1073741824 [ 3.639767] UMP: UMP device driver -0d88e3e loaded [ 3.664424] Mali: Mali400 inside of rk3188! [ 3.664436] Mali: mali freq table num : 6 [ 3.664444] Mali: mali freq table :Mali: 132,Mali: 179,Mali: 223,Mali: 297,Mali: 297,Mali: 446,Mali: [ 3.664477] Mali: init mali clock success [ 3.665799] Mali: Mali device driver loaded [ 3.668974] rk30_mirroring: Unknown symbol video_data_to_mirroring (err 0) [ 3.669014] rk30_mirroring: Unknown symbol audio_data_to_mirroring (err 0) [ 3.680458] rk29_ipp: module is from the staging directory, the quality is unknown, you have been warned. [ 3.681315] ipp irq 47 [ 3.681612] IPP init, version rk30-ipp 1.003 [ 3.754700] init: /dev/hw_random not found [ 3.775184] binder: 97:97 transaction failed 29189, size 0-0 [ 3.781220] init: cannot find '/system/vendor/bin/pvrsrvctl', disabling 'pvrsrvctl' [ 3.788235] init: cannot find '/system/bin/rild3', disabling 'ril-daemon3' [ 3.790696] init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery' [ 4.000775] init: cannot find '/system/bin/bplus_helper', disabling 'bplus_helper' [ 4.001668] init: property 'ro.serialno' doesn't exist while expanding '${ro.serialno}' [ 4.001684] init: cannot expand '${ro.serialno}' while writing to '/sys/class/android_usb/android0/iSerial' [ 4.001873] init: using deprecated syntax for specifying property 'ro.product.usbfactory', use ${name} instead [ 4.055276] warning: `su' uses 32-bit capabilities (legacy support in use) [ 4.067910] init: property 'sys.powerctl' doesn't exist while expanding '${sys.powerctl}' [ 4.076129] init: powerctl: cannot expand '${sys.powerctl}' [ 4.081991] init: property 'sys.sysctl.extra_free_kbytes' doesn't exist while expanding '${sys.sysctl.extra_free_kbytes}' [ 4.082122] RKNAND_GET_DRM_KEY [ 4.082131] return ret = 0 [ 4.098701] init: cannot expand '${sys.sysctl.extra_free_kbytes}' while writing to '/proc/sys/vm/extra_free_kbytes' [ 4.109579] android_usb: already disabled [ 4.113962] mtp_bind_config [ 4.206611] EXT4-fs (mtdblock8): re-mounted. Opts: (null) [ 4.301795] fs_mgr: parse_link_device : path = NULL [ 4.306540] fs_mgr: parse_link_device : path = NULL [ 4.311459] fs_mgr: parse_link_device : path = NULL [ 4.316361] fs_mgr: parse_link_device : path = NULL [ 4.318929] fs_mgr: parse_link_device : path = NULL [ 4.318956] fs_mgr: parse_link_device : path = NULL [ 4.318982] fs_mgr: parse_link_device : path = NULL [ 4.319011] fs_mgr: parse_link_device : path = NULL [ 4.319384] .204.. MMC0 receive the message sd-No-Media from VOLD.[sd_mmc] [ 4.319394] .235.. MMC0 receive the message No-Media from VOLD. waitTimes=0 [sd_mmc] [ 4.474879] EXT4-fs (mtdblock8): re-mounted. Opts: (null) [ 4.479978] .204.. MMC0 receive the message sd-Pending from VOLD.[sd_mmc] [ 4.480145] .204.. MMC0 receive the message sd-Idle-Unmounted from VOLD.[sd_mmc] [ 4.568852] EXT4-fs (mtdblock8): re-mounted. Opts: (null) [ 4.889076] rk fb use 3 buffers [ 6.181084] init: sys_prop: permission denied uid:1000 name:sys_graphic.cam_hal.ver there's also a "recovery" button, when I push it while powering it boots to a different recovery image, and gives me a simple sh shell with busybox installed. the setup there looks pretty limited, with no Wi-Fi connectivity etc: Spoiler DDR Version 1.04 20140217 In DDR3 300MHz Bus Width=32 Col=10 Bank=8 Row=16 CS=1 Die Bus-Width=8 Size=2048MB Memory OK OUT BUILD=====2 No.1 FLASH ID:2c 64 44 4b a9 0 OK! 742309 unsigned! SecureBootEn = 0 0 Boot ver: 2014-03-03#2.13 RECOVERY key is pressed UsbBoot 747700 UsbHook ...1401967 powerOn 1401992 1401990 11402270 12138882 Starting kernel...@0x60408000 Uncompressing Linux... done, booting the kernel. [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.0.36+ (wasser19641@gmail.com) (gcc version 4.7 (GCC) ) #306 SMP PREEMPT Sun Oct 12 11:26:31 CEST 2014 [ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: RK30board [ 0.000000] ddr size = 2048 M, set ion_reserve_size size to 125829120 [ 0.000000] memory reserve: Memory(base:0x98800000 size:120M) reserved for <ion> [ 0.000000] memory reserve: Memory(base:0x97000000 size:24M) reserved for <fb0 buf> [ 0.000000] memory reserve: Total reserved 144M [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] CPU SRAM: copied sram code from c0f19000 to fef00100 - fef020c0 [ 0.000000] CPU SRAM: copied sram data from c0f1afc0 to fef020c0 - fef029e4 [ 0.000000] sram_log: @ 0q @ P 1 / ! aB@ 2 `" 2q : 4q [ 0.000000] CLKDATA_MSG: pll_flag = 0x03 [ 0.000000] cpll auto set rate error [ 0.000000] L310 cache controller enabled [ 0.000000] l2x0: 16 ways, CACHE_ID 0x4100c0c8, AUX_CTRL 0x76050001, Cache size: 524288 B [ 0.000000] DDR DEBUG: version 1.00 20131106 [ 0.000000] DDR DEBUG: DDR3 Device [ 0.000000] DDR DEBUG: Bus Width=32 Col=10 Bank=8 Row=16 CS=1 Total Capability=2048MB [ 0.000000] DDR DEBUG: init success!!! freq=300MHz [ 0.000000] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=0x4, DGSL=1 extra clock, DGPS=90 [ 0.000000] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=0x4, DGSL=1 extra clock, DGPS=90 [ 0.000000] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=0x4, DGSL=1 extra clock, DGPS=90 [ 0.000000] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=0x4, DGSL=1 extra clock, DGPS=90 [ 0.000000] DDR DEBUG: ZERR=0, ZDONE=0, ZPD=0x0, ZPU=0x0, OPD=0x0, OPU=0x0 [ 0.000000] DDR DEBUG: DRV Pull-Up=0xb, DRV Pull-Dwn=0xb [ 0.000000] DDR DEBUG: ODT Pull-Up=0x2, ODT Pull-Dwn=0x2 [ 0.000000] Boot mode: RECOVERY (2) flag: RECOVER (0xc3524203) [ 0.000000] PERCPU: Embedded 7 pages/cpu @c343d000 s6976 r8192 d13504 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 483328 [ 0.000000] Kernel command line: console=ttyFIQ0 androidboot.console=ttyFIQ0 init=/init initrd=0x62000000,0x00430000 mtdparts=rk29xxnand:0x00002000@0x00000000(parameter),0x00002000@0x0000 2000(misc),0x00006000@0x00004000(kernel),0x00006000@0x0000a000(boot),0x00010000@0x00010000(recovery),0x00020000@0x00020000(backup),0x00040000@0x00040000(cache),0x00002000@0x00080000(metadata ),0x00002000@0x00082000(kpanic),0x00272000@0x00084000(system),-@0x002F6000(userdata) bootver=2014-03-03#2.13 firmware_ver=4.4.2 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] allocated 8388608 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 880MB 1024MB = 1904MB total [ 0.000000] Memory: 1898432k/1898432k available, 198720k reserved, 1449984K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] DMA : 0xff600000 - 0xffe00000 ( 8 MB) [ 0.000000] vmalloc : 0xdf000000 - 0xfe800000 ( 504 MB) [ 0.000000] lowmem : 0xc0000000 - 0xde800000 ( 488 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .init : 0xc0408000 - 0xc062f000 (2204 kB) [ 0.000000] .text : 0xc062f000 - 0xc0e840a4 (8533 kB) [ 0.000000] .data : 0xc0e86000 - 0xc0f18b28 ( 587 kB) [ 0.000000] .bss : 0xc0f1c024 - 0xc194e328 (10441 kB) [ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:352 [ 0.000000] rk30_gpio_init: 128 gpio irqs in 4 banks [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms [ 0.000000] rk_timer: version 1.3 [ 0.003740] Calibrating delay loop (skipped) preset value.. 1583.48 BogoMIPS (lpj=7917420) [ 0.012874] pid_max: default: 32768 minimum: 301 [ 0.018136] Security Framework initialized [ 0.022768] Mount-cache hash table entries: 512 [ 0.028338] Initializing cgroup subsys debug [ 0.033101] Initializing cgroup subsys cpuacct [ 0.038076] Initializing cgroup subsys memory [ 0.042949] Initializing cgroup subsys freezer [ 0.047922] CPU: Testing write buffer coherency: ok [ 0.134186] CPU1: Booted secondary processor [ 0.174184] CPU2: Booted secondary processor [ 0.214180] CPU3: Booted secondary processor [ 0.214217] Brought up 4 CPUs [ 0.231820] SMP: Total of 4 processors activated (6333.93 BogoMIPS). [ 0.239184] devtmpfs: initialized [ 0.249127] NET: Registered protocol family 16 [ 0.254477] DVFS MSG: AVS Value(index=0): 129 129 128 127 128 128 129 129 129 129 [ 0.273372] lcdc0 is used as external display device contoller! [ 0.279956] lcdc1 is used as primary display device controller! [ 0.386731] rk29sdk_wifi_bt_gpio_control_init: init finished <hit enter to activate fiq debugger> 0.394287] console [ttyFIQ0] enabled, bootconsole disabled [ 0.394287] console [ttyFIQ0] enabled, bootconsole disabled [ 0.403289] Registered FIQ tty driver de0adc00 [ 0.403872] Loaded driver for PL330 DMAC-1 rk29-pl330 [ 0.403888] DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12 [ 0.404038] Loaded driver for PL330 DMAC-2 rk29-pl330 [ 0.404051] DBUFF-64x8bytes Num_Chans-7 Num_Peri-20 Num_Events-14 [ 0.435923] bio: create slab <bio-0> at 0 [ 0.440329] SCSI subsystem initialized [ 0.440513] usbcore: registered new interface driver usbfs [ 0.440605] usbcore: registered new interface driver hub [ 0.454879] usbcore: registered new device driver usb [ 0.455258] rk30_i2c rk30_i2c.0: i2c-0: RK30 I2C adapter [ 0.455479] rk30_i2c rk30_i2c.1: i2c-1: RK30 I2C adapter [ 0.455646] rk30_i2c rk30_i2c.2: i2c-2: RK30 I2C adapter [ 0.455750] rk30_i2c rk30_i2c.3: i2c-3: RK30 I2C adapter [ 0.455854] rk30_i2c rk30_i2c.4: i2c-4: RK30 I2C adapter [ 0.486434] rk30-adc rk30-adc: rk30 adc: driver initialized [ 0.486501] RK29 Watchdog Timer, (c) 2011 Rockchip Electronics [ 0.486677] rk29-wdt rk29-wdt.0: starting watchdog timer [ 0.486913] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 0.487319] Bluetooth: Core ver 2.16 [ 0.487367] NET: Registered protocol family 31 [ 0.487379] Bluetooth: HCI device and connection manager initialized [ 0.487393] Bluetooth: HCI socket layer initialized [ 0.487405] Bluetooth: L2CAP socket layer initialized [ 0.487430] Bluetooth: SCO socket layer initialized [ 0.488466] rk fb probe ok! [ 0.493150] act8846_set_init,line=17 [ 0.493163] act8846_set_init:g_pmic_type=3 [ 0.494836] act8846_set_init act_dcdc1 =1200000mV end [ 0.496592] act8846_set_init vdd_core =1000000mV end [ 0.498341] act8846_set_init vdd_cpu =1000000mV end [ 0.500094] act8846_set_init act_dcdc4 =3300000mV end [ 0.501248] act8846_set_init act_ldo1 =1000000mV end [ 0.502898] act8846_set_init act_ldo2 =1200000mV end [ 0.504558] act8846_set_init act_ldo3 =1800000mV end [ 0.506210] act8846_set_init act_ldo4 =3300000mV end [ 0.507859] act8846_set_init act_ldo5 =3300000mV end [ 0.509508] act8846_set_init act_ldo6 =3300000mV end [ 0.510559] act8846_set_init act_ldo7 =1800000mV end [ 0.512207] act8846_set_init act_ldo8 =2800000mV end [ 0.512225] act8846_set_init,line=78 END [ 0.512269] i2c-core: driver [act8846] using legacy suspend method [ 0.512281] i2c-core: driver [act8846] using legacy resume method [ 0.512322] rk1000_control_probe [ 0.537211] rk1000_control_probe ok [ 0.537273] Switching to clocksource rk_timer [ 0.543547] Switched to NOHz mode on CPU #0 [ 0.544222] Switched to NOHz mode on CPU #2 [ 0.544230] Switched to NOHz mode on CPU #3 [ 0.544239] Switched to NOHz mode on CPU #1 [ 0.544574] lcdc1:reg_phy_base = 0x1010e000,reg_vir_base:0xdf02c000 [ 0.544618] fb0:win0 [ 0.544621] fb1:win1 [ 0.544624] fb2:win2 [ 0.544682] rk3188 lcdc1 clk enable... [ 0.569762] rk3188 lcdc1 clk disable... [ 0.628030] fb0:phy:97000000>>vir:e0000000>>len:0x1800000 [ 0.628272] rk_fb_register>>>>>fb0 [ 0.628566] rk_fb_register>>>>>fb1 [ 0.661052] rk3188 lcdc1 probe ok! [ 0.661129] lcdc0:reg_phy_base = 0x1010c000,reg_vir_base:0xdf040000 [ 0.661181] fb0:win0 [ 0.661185] fb1:win1 [ 0.661187] fb2:win2 [ 0.661251] rk3188 lcdc0 clk enable... [ 0.686323] rk3188 lcdc0 clk disable... [ 0.686340] fb2:phy:97000000>>vir:e0000000>>len:0x1800000 [ 0.686568] rk_fb_register>>>>>fb2 [ 0.686861] rk_fb_register>>>>>fb3 [ 0.686874] rk3188 lcdc0 probe ok! [ 0.724657] cfg80211: Calling CRDA to update world regulatory domain [ 0.747743] IT66121 probe success. [ 0.751118] NET: Registered protocol family 2 [ 0.751237] IP route cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.751543] TCP established hash table entries: 65536 (order: 7, 524288 bytes) [ 0.752516] TCP bind hash table entries: 65536 (order: 7, 786432 bytes) [ 0.753937] TCP: Hash tables configured (established 65536 bind 65536) [ 0.753949] TCP reno registered [ 0.753961] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.753987] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.754263] NET: Registered protocol family 1 [ 0.802587] RPC: Registered named UNIX socket transport module. [ 0.802602] RPC: Registered udp transport module. [ 0.802612] RPC: Registered tcp transport module. [ 0.802622] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.802789] Unpacking initramfs... [ 1.002882] Freeing initrd memory: 4288K [ 1.002976] PMU: registered new PMU device of type 0 [ 1.003091] efuse_version_val: efuse version = 51 [ 1.003105] DVFS MSG: core: dvfs_adjust_table_lmtvolt get leakage_level = 17000 [ 1.003119] adjust table freq=1608000 KHz, index=1350000 mV to index=1250000 mV [ 1.003134] efuse_version_val: efuse version = 51 [ 1.003145] DVFS MSG: aclk_gpu: dvfs_adjust_table_lmtvolt get leakage_level = 17000 [ 1.003967] cpufreq: delete arm freq(1608000) [ 1.047994] rk3188 cpufreq version 2.2, suspend freq 816 MHz [ 1.048215] vpu: power on [ 1.048265] VPU_SERVICE: checking hw id 4831 [ 1.060860] vpu: power off...done [ 1.060899] VPU_SERVICE: init success [ 1.061152] audit: initializing netlink socket (disabled) [ 1.061190] type=2000 audit(1.000:1): initialized [ 1.078087] highmem bounce pool size: 64 pages [ 1.078262] ashmem: initialized [ 1.089043] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.089291] NTFS driver 2.1.30 [Flags: R/W]. [ 1.089450] fuse init (API version 7.16) [ 1.104467] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 1.104480] io scheduler noop registered [ 1.104486] io scheduler deadline registered [ 1.104526] io scheduler cfq registered (default) [ 1.124809] rga: Driver loaded succesfully [ 1.124938] rk_serial.c v1.6 2013-12-23 [ 1.124996] rk_serial.0: ttyS0 at MMIO 0x10124000 (irq = 66) is a rk29_serial.0 [ 1.125085] rk_serial rk_serial.0: membase 0xdf048000 [ 1.125131] rk_serial.3: ttyS3 at MMIO 0x20068000 (irq = 69) is a rk29_serial.3 [ 1.125216] rk_serial rk_serial.3: membase 0xdf050000 [ 1.125368] Rockchip ion module(version: 1.0) is successfully loaded [ 1.126888] loop: module loaded [ 1.126918] Android kernel panic handler initialized (bind=kpanic) [ 1.127420] PPP generic driver version 2.4.2 [ 1.127517] PPP Deflate Compression module registered [ 1.127525] PPP BSD Compression module registered [ 1.187263] PPP MPPE Compression module registered [ 1.187275] NET: Registered protocol family 24 [ 1.187283] tun: Universal TUN/TAP device driver, 1.6 [ 1.187290] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 1.187462] usbcore: registered new interface driver sr9700_android [ 1.187480] Rockchip WiFi SYS interface (V1.00) ... [ 1.187512] Initializing USB Mass Storage driver... [ 1.187555] usbcore: registered new interface driver usb-storage [ 1.187562] USB Mass Storage support registered. [ 1.187637] usbcore: registered new interface driver usbserial [ 1.187663] USB Serial support registered for generic [ 1.187692] usbcore: registered new interface driver usbserial_generic [ 1.187698] usbserial: USB Serial Driver core [ 1.187720] USB Serial support registered for GSM modem (1-port) [ 1.187750] usbcore: registered new interface driver option [ 1.187756] option: v0.7.2:USB Driver for GSM modems [ 1.187778] USB Serial support registered for usi-modem [ 1.187810] usbcore: registered new interface driver usi-modem [ 1.409297] DWC_OTG: ^^^^^^^^^^^^^^^^^^Host Mode [ 1.409314] usb20_otg usb20_otg: DWC OTG Controller [ 1.409381] usb20_otg usb20_otg: new USB bus registered, assigned bus number 1 [ 1.409407] usb20_otg usb20_otg: irq 48, io mem 0x00000000 [ 1.409435] DWC_OTG: Init: Port Power? op_state=1 [ 1.409440] DWC_OTG: Init: Power Port (0) [ 1.409481] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.409490] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.409498] usb usb1: Product: DWC OTG Controller [ 1.409504] usb usb1: Manufacturer: Linux 3.0.36+ dwc_otg_hcd [ 1.409510] usb usb1: SerialNumber: usb20_otg [ 1.409768] hub 1-0:1.0: USB hub found [ 1.409783] hub 1-0:1.0: 1 port detected [ 1.412314] DWC_OTG: host20_driver_probe host2.0 reg addr: 0x101c0000 remap:0xdf100000 [ 1.622668] DWC_OTG: ^^^^^^^^^^^^^^^^^^Host Mode [ 1.622697] usb20_host usb20_host: DWC OTG Controller [ 1.622724] usb20_host usb20_host: new USB bus registered, assigned bus number 2 [ 1.622751] usb20_host usb20_host: irq 49, io mem 0x00000000 [ 1.622791] DWC_OTG: Init: Port Power? op_state=1 [ 1.622796] DWC_OTG: Init: Power Port (0) [ 1.622828] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.622837] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.622845] usb usb2: Product: DWC OTG Controller [ 1.622851] usb usb2: Manufacturer: Linux 3.0.36+ host20_hcd [ 1.622858] usb usb2: SerialNumber: usb20_host [ 1.623096] hub 2-0:1.0: USB hub found [ 1.623107] hub 2-0:1.0: 1 port detected [ 1.623432] DWC_OTG: Mode Mismatch Interrupt: currently in Host mode [ 1.696903] android_usb gadget: Mass Storage Function, version: 2009/09/11 [ 1.696914] android_usb gadget: Number of LUNs=2 [ 1.696921] lun0: LUN: removable file: (no medium) [ 1.696928] lun1: LUN: removable file: (no medium) [ 1.697112] android_usb gadget: android_usb ready [ 1.697283] input: rk29-keypad as /devices/platform/rk29-keypad/input/input0 [ 1.697509] usbcore: registered new interface driver xpad [ 1.697677] remotectl probe j=0x0 [ 1.697684] remotectl probe j=0x1 [ 1.697689] remotectl probe j=0x2 [ 1.697694] remotectl probe j=0x3 [ 1.697698] remotectl probe j=0x4 [ 1.697703] remotectl probe j=0x5 [ 1.697707] remotectl probe j=0x6 [ 1.697713] remotectl probe j=0x7 [ 1.697829] input: rkxx-remotectl as /devices/platform/rkxx-remotectl/input/input1 [ 1.699929] rtc_hym8563 1-0051: clock/calendar information is no longer guaranteed [ 1.702570] using rtc device, rtc_hym8563, for alarms [ 1.702594] rtc_hym8563 1-0051: rtc core: registered rtc_hym8563 as rtc0 [ 1.702624] i2c /dev entries driver [ 1.703052] lirc_dev: IR Remote Control driver registered, major 250 [ 1.703061] IR NEC protocol handler initialized [ 1.703066] IR RC5(x) protocol handler initialized [ 1.703072] IR RC6 protocol handler initialized [ 1.703077] IR JVC protocol handler initialized [ 1.703082] IR Sony protocol handler initialized [ 1.703087] IR RC5 (streamzap) protocol handler initialized [ 1.703093] IR LIRC bridge handler initialized [ 1.703098] Linux video capture interface: v2.00 [ 1.703154] usbcore: registered new interface driver uvcvideo [ 1.703161] USB Video Class driver (v1.1.0) [ 1.703192] def_ref_volt: 1800mV, curr_ref_volt: 1800mV [ 1.703712] device-mapper: uevent: version 1.0.3 [ 1.703904] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com [ 1.704045] Bluetooth: HCI UART driver ver 2.2 [ 1.704054] Bluetooth: HCI H4 protocol initialized [ 1.704060] Bluetooth: HCI Realtek H5 protocol initialized [ 1.704066] Bluetooth: Generic Bluetooth SDIO driver ver 0.1 [ 1.704125] cpuidle: using governor ladder [ 1.704130] cpuidle: using governor menu [ 1.749511] [ 1.749514] drivers/mmc/core/core.c...2019.. ===== mmc_rescan Begin....[mmc0] [ 1.754568] rk29_sdmmc_change_clk_div..1684.. newDiv=62, newCLK=299Khz [sd_mmc] [ 1.754594] .Line4018..The End of SDMMC-probe Ver.6.07 The last modify date is 2013-12-20. [sd_mmc] [ 1.754722] .Line4018..The End of SDMMC-probe Ver.6.07 The last modify date is 2013-12-20. [sdio] [ 1.756052] usbcore: registered new interface driver usbhid [ 1.756060] usbhid: USB HID core driver [ 1.756312] logger: created 256K log 'log_main' [ 1.756365] logger: created 256K log 'log_events' [ 1.756418] logger: created 256K log 'log_radio' [ 1.756470] logger: created 256K log 'log_system' [ 1.756766] zram: Created 1 device(s) ... [ 1.757156] i2c-core: driver [RK1000_CODEC] using legacy suspend method [ 1.757166] i2c-core: driver [RK1000_CODEC] using legacy resume method [ 1.807097] [ 1.807099] mmc_attach_sd..1230.. ===== Begin to identify card as SD-card. [mmc0] [ 1.914576] register rk1000 codec earlysuspend ok [ 1.914590] RK1000_CODEC 0-0060: Failed to add route Left DAC->Left Mixer [ 1.918332] rk29_sdmmc_change_clk_div..1684.. newDiv=0, newCLK=37125Khz [sd_mmc] [ 1.918383] mmc0: new high speed SDHC card at address 0001 [ 1.918578] mmcblk0: mmc0:0001 SD32G 29.1 GiB [ 1.919959] [ 1.919961] msdos_partition..466... ==== Begin to parse sdcard-partition. [mmcblk0] [ 1.919976] msdos_partition..535... ==== The sdcard has MBR. [mmcblk0] [ 1.919985] msdos_partition..548... ==== partition-1, size=1981MB. [mmcblk0] [ 1.919993] msdos_partition..576... ==== main partition-1....[mmcblk0] [ 1.920001] msdos_partition..548... ==== partition-2, size=51MB. [mmcblk0] [ 1.920009] msdos_partition..576... ==== main partition-2....[mmcblk0] [ 1.920016] mmcblk0: p1 p2 [ 1.920379] sdmmc_rescan_try_freq..1913.. ===== Initialize SD-card successfully. [mmc0] [ 1.920396] [ 1.920398] drivers/mmc/core/core.c...2019.. ===== mmc_rescan Begin....[mmc1] [ 1.923888] asoc: rk1000_codec <-> rk29_i2s.1 mapping ok [ 1.924170] ALSA device list: [ 1.924176] #0: RK29_RK1000 [ 1.924273] GACT probability NOT on [ 1.924283] Mirror/redirect action on [ 1.924289] u32 classifier [ 1.924292] Actions configured [ 1.924299] Netfilter messages via NETLINK v0.30. [ 1.924338] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 1.924601] ctnetlink v0.93: registering with nfnetlink. [ 1.924632] NF_TPROXY: Transparent proxy support initialized, version 4.1.0 [ 1.924639] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd. [ 1.924876] xt_time: kernel timezone is -0000 [ 1.924994] ip_tables: (C) 2000-2006 Netfilter Core Team [ 1.925115] arp_tables: (C) 2002 David S. Miller [ 1.925153] TCP cubic registered [ 1.925159] Initializing XFRM netlink socket [ 1.925509] NET: Registered protocol family 10 [ 1.926045] Mobile IPv6 [ 1.926071] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 1.926179] IPv6 over IPv4 tunneling driver [ 1.926741] NET: Registered protocol family 17 [ 1.926766] NET: Registered protocol family 15 [ 1.926948] Bluetooth: RFCOMM TTY layer initialized [ 1.926964] Bluetooth: RFCOMM socket layer initialized [ 1.926971] Bluetooth: RFCOMM ver 1.11 [ 1.926978] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 1.926986] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 1.927114] NET: Registered protocol family 35 [ 1.927190] [BT_RFKILL]: Enter rfkill_rk_init [ 1.927265] [BT_RFKILL]: Request irq for bt wakeup host [ 1.927285] [BT_RFKILL]: ** disable irq [ 1.927397] [BT_RFKILL]: bt shut off power [ 1.937333] rk29_sdmmc_change_clk_div..1684.. newDiv=42, newCLK=294Khz [sdio] [ 1.960410] [BT_RFKILL]: bt_default device registered. [ 1.960458] Registering the dns_resolver key type [ 1.960481] pmic set pm_suspend_volt: [ 1.960493] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 1.960515] Registering SWP/SWPB emulation handler [ 1.960929] ddrfreq: verion 3.2 20131126 [ 1.960936] ddrfreq: fix cpu pause bug [ 1.960943] ddrfreq: normal 456MHz video 0MHz video_low 0MHz dualview 0MHz idle 0MHz suspend 0MHz reboot 300MHz [ 1.961259] rk3188 lcdc0 clk enable... [ 1.961273] lcdc0: dclk:148500000>>fps:60 [ 1.961282] rk30-lcdc rk30-lcdc.0: rk3188_load_screen for lcdc0 ok! [ 1.961768] ddrfreq: change freq to 445 MHz when normal [ 1.961914] lcdc0: dclk:27000000>>fps:60 [ 1.964072] rk30-lcdc rk30-lcdc.0: rk3188_load_screen for lcdc0 ok! [ 1.964082] lcdc0 wakeup from standby! [ 1.964087] lcdc0 win0 open,atv layer:1 [ 1.964098] lcdc0 win1 closed,atv layer:1 [ 1.964106] rk1000_tv ver 2.0 probe ok [ 1.964911] rtc_hym8563 1-0051: setting system clock to 2011-01-01 12:00:00 UTC (1293883200) [ 1.967592] asoc: dit-hifi <-> rk-spdif mapping ok [ 1.967991] usbcore: registered new interface driver snd-usb-audio [ 1.968285] Freeing init memory: 2204K [ 2.007403] usb 2-1: new high speed USB device number 2 using usb20_host [ 2.217975] usb 2-1: New USB device found, idVendor=1a40, idProduct=0101 [ 2.217987] usb 2-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 2.217996] usb 2-1: Product: USB 2.0 Hub [ 2.218402] hub 2-1:1.0: USB hub found [ 2.218467] hub 2-1:1.0: 4 ports detected [ 2.517464] usb 2-1.4: new full speed USB device number 3 using usb20_host [ 2.638071] usb 2-1.4: New USB device found, idVendor=0fe6, idProduct=9700 [ 2.638083] usb 2-1.4: New USB device strings: Mfr=0, Product=2, SerialNumber=0 [ 2.638092] usb 2-1.4: Product: USB 2.0 10/100M Ethernet Adaptor [ 2.678056] sr9700_android 2-1.4:1.0: eth0: register 'sr9700_android' at usb-usb20_host-1.4, SR9700_ANDROID USB Ethernet, 00:e0:4c:53:44:58 [ 2.868585] init: /dev/hw_random not found [ 2.868849] android_usb: already disabled [ 2.869005] init: property 'ro.serialno' doesn't exist while expanding '${ro.serialno}' [ 2.869017] init: cannot expand '${ro.serialno}' while writing to '/sys/class/android_usb/android0/iSerial' [ 2.877895] gp_rknand_info = : 0xde248400 [ 2.877961] rk30_chip_set:1 [ 2.878016] FtlInit! [ 2.878035] No.1 FLASH ID:2c 64 44 4b a9 0 [ 2.879596] FTL version: 5.0.12 20140214 [ 2.994673] gBootMedia = 1 gSdmmcFwPartOffset =0! [ 2.994683] rknand_buffer.c version: 4.40 20130830! [ 3.004330] 11 cmdlinepart partitions found on MTD device rk29xxnand [ 3.004340] Creating 11 MTD partitions on "rk29xxnand": [ 3.004350] 0x000000000000-0x000000400000 : "parameter" [ 3.021374] 0x000000400000-0x000000800000 : "misc" [ 3.026427] 0x000000800000-0x000001400000 : "kernel" [ 3.031647] 0x000001400000-0x000002000000 : "boot" [ 3.036672] 0x000002000000-0x000004000000 : "recovery" [ 3.042045] 0x000004000000-0x000008000000 : "backup" [ 3.047253] 0x000008000000-0x000010000000 : "cache" [ 3.052376] 0x000010000000-0x000010400000 : "metadata" [ 3.057774] 0x000010400000-0x000010800000 : "kpanic" [ 3.063432] apanic: Bound to mtd partition 'kpanic' [ 3.063441] apanic: No panic data available [ 3.063454] 0x000010800000-0x00005ec00000 : "system" [ 3.077651] 0x00005ec00000-0x0001df400000 : "userdata" [ 3.111943] EXT4-fs (mtdblock6): mounted filesystem with ordered data mode. Opts: discard rty__irectocyopeana/pdape: yoerrnot find any tzdata when looking for GMT! __bionic_open_tzdata: couldn't find any tzdata when looking for posixrules! Starting recovery on Sat Jan 1 12:00:01 2011 bootmode = unknown recovery filesystem table ========================= 0 /mnt/internal_sd vfat /dev/block/mtd/by-name/user 0 1 /mnt/external_sd vfat /dev/block/mmcblk0 0 2 /system ext4 /dev/block/mtd/by-name/system 0 3 /cache ext4 /dev/block/mtd/by-name/cache 0 4 /metadata ext4 /dev/block/mtd/by-name/metadata 0 5 /data ext4 /dev/block/mtd/by-name/userdata 0 6 /cust ext4 /dev/block/mtd/by-name/cust 0 7 /custom ext4 /dev/block/mtd/by-name/custom 0 8 /misc mtd misc 0 9 /uboot mtd uboot 0 10 /charge mtd charge 0 11 /parameter mtd parameter 0 12 /boot mtd boot 0 13 /recovery mtd recovery 0 14 /backup mtd backup 0 15 /tmp ramdisk ramdisk 0 I:InternalSD_ROOT: /mnt/internal_sd I:ExternalSD_ROOT: /mnt/external_sd I:Set boot command "boot-recovery" locale is [(null)] stage is [] failed to read font: res=-1 can't open /dev/tty0: No such file or directory framebuffer: fd 3 (1920 x 1080) [ 3.234131] rk30-lcdc rk30-lcdc.0: blank mode:4 [ 3.234143] rk30-lcdc rk30-lcdc.0: blank mode:0 installing_text: (1 x 1 @ 1896) erasing_text: (1 x 1 @ 1599) no_command_text: (1 x 1 @ 1599) error_text: (1 x 1 @ 1599) Recovery system v4.4.0 Recovery system v4.4.0 [ 3.354441] EXT4-fs (mtdblock7): warning: mounting unchecked fs, running e2fsck is recommended [ 3.354611] EXT4-fs (mtdblock7): mounted filesystem without journal. Opts: [ 3.355352] FAT-fs (mmcblk0): invalid media value (0x00) [ 3.355361] FAT-fs (mmcblk0): Can't find a valid FAT filesystem W:trying mount /dev/block/mmcblk0 to ntfs [ 3.468709] NTFS-fs error (device mmcblk0): read_ntfs_boot_sector(): Primary boot sector is invalid. [ 3.468723] NTFS-fs error (device mmcblk0): read_ntfs_boot_sector(): Mount option errors=recover not used. Aborting without trying to recover. [ 3.468734] NTFS-fs error (device mmcblk0): ntfs_fill_super(): Not an NTFS volume. read cmdline Not enter sdboot! auto sdcard update path: /mnt/external_sd/FirmwareUpdate/auto_sd_update.tag bootmode = unknown Command: "/sbin/recovery" ro.rk.cpu=rk3188 ro.rk.soc=rk3188+ ro.rk.wifi_on=false ro.rk.bt_enable=true ro.rk.systembar.tabletUI=false ro.rk.systembar.voiceicon=true ro.rk.MassStorage=false ro.rk.changescreen=false ro.rk.homepage_base=http://pikotv.com ro.rk.def_brightness=200 ro.rk.screenoff_time=-1 ro.rk.screenshot_enable=true ro.rk.install_non_market_apps=truerue ro.sf.hwrotation=0 ro.sf.lcd_density=160 ro.sf.fakerotation=false ro.sf.lcdc_composer=0 ro.adb.secure=0 ro.com.android.dateformat=MM-dd-yyyy ro.com.android.dataroaming=true ro.ril.ecclist=112,911 ro.sms.capable=false ro.boot.console=ttyFIQ0 ro.dlna.devicename=eHomeCenter ro.wifi.channels= ro.allow.mock.location=0 ro.audio.monitorOrientation=true ro.board.platform=rk3188 ro.build.id=KOT49H ro.build.date=Sun Oct 12 14:41:31 CEST 2014 ro.build.date.utc=1413117691 ro.build.host=pfullingen.str.redhat.com ro.build.tags=test-keys ro.build.type=user ro.build.user=wasser ro.build.display.id=KOT49H test-keys ro.build.product=rk3188 ro.build.version.sdk=19 ro.build.version.release=4.4.2 ro.build.version.codename=REL ro.build.version.incremental=eng.wasser.20141012.143755 ro.build.description=rk3188-user 4.4.2 KOT49H eng.wasser.20141012.143755 test-keys ro.build.fingerprint=rockchip/rk3188/rk3188:4.4.2/KOT49H/eng.wasser.20141012.143755:user/test-keys ro.build.characteristics=tablet ro.rksdk.version=RK30_ANDROID$(PLATFORM_VERSION)-SDK-v1.00.00 \ ro.voice.capable=false ro.ap_mdm=-1 ro.config.ringtone=Ring_Synth_04.ogg ro.config.alarm_alert=Alarm_Classic.ogg ro.config.notification_sound=pixiedust.ogg ro.kernel.android.checkjni=0 ro.secure=0 ro.tether.denied=false ro.vendor.sw.version=1.0.5 ro.carrier=unknown ro.default.size=100 ro.factory.tool=0 ro.factory.hasGPS=false ro.factory.hasUMS=false ro.factory.without_battery=true ro.factory.storage_suppntfs=true ro.product.cpu.abi=armeabi-v7a ro.product.cpu.abi2=armeabi ro.product.name=rk3188 ro.product.board=manta ro.product.brand=google ro.product.model=Nexus 10 ro.product.device=manta ro.product.locale.region=US ro.product.locale.language=en ro.product.version=1.0.0 ro.product.usbfactory=rockchip_usb ro.product.manufacturer=samsung ro.baseband=unknown ro.bootmode=unknown ro.hardware=rk30board ro.opengles.version=131072 ro.revision=0 ro.bootloader=unknown ro.debuggable=0 ro.ap_has_alsa=-1 ro.factorytest=0 ro.ap_data_only=-1 ro.ap_has_earphone=-1 sf.power.control=2073600 net.bt.name=Android net.change=net.bt.name ril.function.dataonly=1 sys.hwc.compose_policy=6 sys.rkadb.wasser=0 sys.wallpaper.rgb565=0 sys.resolution.changed=false init.svc.console=running init.svc.ueventd=running init.svc.recovery=running rild.libargs=-d /dev/ttyACM0 rild.libpath=/system/lib/libril-rk29-dataonly.so rild.libpath1=/system/lib/libreference-ril-mt6229.so rild.libpath2=/system/lib/libreference-ril-mu509.so rild.libpath4=/system/lib/libreference-ril-mw100.so rild.libpath6=/system/lib/libreference-ril-sc6610.so rild.libpath7=/system/lib/libreference-ril-m51.so rild.libpath8=/system/lib/libreference-ril-mt6250.so rild.libpath9=/system/lib/libreference-ril-c66a.so rild.libpath10=/system/lib/libreference-ril-sew290.so rild.libpath11=/system/lib/libreference-ril-u5501.so rild.libpath12=/system/lib/libreference-ril-u7501.so rild.libpath13=/system/lib/libreference-ril-aw706.so rild.libpath14=/system/lib/libreference-ril-a85xx.so rild.libpath15=/system/lib/libreference-ril-e1230s.so wifi.interface=wlan0 wifi.supplicant_scan_interval=15 debug.nfc.se=false debug.nfc.fw_download=false debug.hwui.render_dirty_regions=false media.rmvb.support=1 rild1.libpath=/system/lib/libreference-ril-sc6610-1.so rild3.libpath=/system/lib/libril-rk29-dataonly.so video.use.overlay=0 video.bluray.render=gpu video.bluray.navigationMenu=hide dalvik.vm.jniopts=warnonly dalvik.vm.heapsize=384m dalvik.vm.heapmaxfree=8m dalvik.vm.heapminfree=512k dalvik.vm.dexopt-flags=m=y dalvik.vm.heapstartsize=8m dalvik.vm.heapgrowthlimit=64m dalvik.vm.stack-trace-file=/data/anr/traces.txt dalvik.vm.heaptargetutilization=0.75 persist.sys.usb.config=mtp,adb persist.sys.dalvik.vm.lib=libdvm.so persist.sys.timezone=Europe/Berlin persist.sys.strictmode.visual=false persist.audio.currentplayback=9 persist.audio.lastsocplayback=9 persist.tegra.nvmmlite=1 keyguard.no_require_sim=true ExternalSD_ROOT=/mnt/external_sd InternalSD_ROOT=/mnt/internal_sd UserVolumeLabel=RockChips I:Set boot command "" heres the busybox output: # busybox BusyBox v1.11.1 (2009-03-11 09:17:49 CST) multi-call binary Copyright (C) 1998-2008 Erik Andersen, Rob Landley, Denys Vlasenko and others. Licensed under GPLv2. See source distribution for full notice. Usage: busybox [function] [arguments]... or: function [arguments]... BusyBox is a multi-call binary that combines many common Unix utilities into a single executable. Most people will create a link to busybox for each function they wish to use and BusyBox will act like whatever it was invoked as! Currently defined functions: [, [[, addgroup, adduser, adjtimex, ar, arp, arping, ash, awk, basename, brctl, bunzip2, bzcat, bzip2, cal, cat, catv, chat, chattr, chgrp, chmod, chown, chpasswd, chpst, chroot, chrt, chvt, cksum, clear, cmp, comm, cp, cpio, crond, crontab, cryptpw, cttyhack, cut, date, dc, dd, deallocvt, delgroup, deluser, depmod, df, dhcprelay, diff, dirname, dmesg, dnsd, dos2unix, du, dumpkmap, dumpleases, echo, ed, egrep, eject, env, envdir, envuidgid, ether-wake, expand, expr, fakeidentd, false, fbset, fbsplash, fdflush, fdformat, fdisk, fetchmail, fgrep, find, fold, free, freeramdisk, fsck, fsck.minix, ftpget, ftpput, fuser, getopt, getty, grep, gunzip, gzip, halt, hdparm, head, hexdump, hostid, hostname, httpd, hush, hwclock, id, ifconfig, ifdown, ifenslave, ifup, inetd, init, inotifyd, insmod, install, ip, ipaddr, ipcalc, ipcrm, ipcs, iplink, iproute, iprule, iptunnel, kbd_mode, kill, killall, killall5, klogd, lash, last, length, less, linux32, linux64, linuxrc, ln, loadfont, loadkmap, logger, login, logname, logread, losetup, lpd, lpq, lpr, ls, lsattr, lsmod, lzmacat, makedevs, man, md5sum, mdev, mesg, microcom, mkdir, mkfifo, mkfs.minix, mknod, mkswap, mktemp, modprobe, more, mount, mountpoint, msh, mt, mv, nameif, nc, netstat, nice, nmeter, nohup, nslookup, od, openvt, passwd, patch, pgrep, pidof, ping, ping6, pipe_progress, pivot_root, pkill, poweroff, printenv, printf, ps, pscan, pwd, raidautorun, rdate, readahead, readlink, readprofile, realpath, reboot, renice, reset, resize, rm, rmdir, rmmod, route, rpm, rpm2cpio, rtcwake, run-parts, runlevel, runsv, runsvdir, rx, script, sed, sendmail, seq, setarch, setconsole, setkeycodes, setlogcons, setsid, setuidgid, sh, sha1sum, slattach, sleep, softlimit, sort, split, start-stop-daemon, stat, strings, stty, su, sulogin, sum, sv, svlogd, swapoff, swapon, switch_root, sync, sysctl, syslogd, tac, tail, tar, taskset, tcpsvd, tee, telnet, telnetd, test, tftp, tftpd, time, top, touch, tr, traceroute, true, tty, ttysize, udhcpc, udhcpd, udpsvd, umount, uname, uncompress, unexpand, uniq, unix2dos, unlzma, unzip, uptime, usleep, uudecode, uuencode, vconfig, vi, vlock, watch, watchdog, wc, wget, which, who, whoami, xargs, yes, zcat, zcip let me know if there is any more info I can give, or anything else I can try!
fabiobassa Posted August 16, 2022 Posted August 16, 2022 No worries @oolonthegreat Just to explain that we haven't any experience on 3188 so we cannot help you .
Recommended Posts