Jump to content

Recommended Posts

Posted

Hi,

 

I installed a fresh Armbian_22.05.4_Rockpi-4a_sid_edge_5.18.0 first on SD-card, then I used nand-sata-install to copy system to emmc. After that I rebooted and set up the nas (rockpi-4a with 4 ssd-drives). I already used ssh remote shell to perform apt dist-upgrade and copying of about 6TB ...

When all setup was finished, I shutdown the system, closed the tower and restarted again.

 

On that restart, the network came up without inet-address. ifconfig showed eth0 and l0, but eth0 had a mac-address (not the one, I configured in armbianEnv.txt) but no ip-address.

Here are some lines from syslog:

Aug 28 15:57:01 mynas NetworkManager[1659]: <info>  [1661695021.5656] device (eth0): state change: disconnected -> unavailable (reason 'carrier-changed', sys-iface-state: 'managed')
Aug 28 15:57:02 mynas NetworkManager[1659]: <info>  [1661695022.7361] device (eth0): carrier: link connected
Aug 28 15:57:02 mynas NetworkManager[1659]: <info>  [1661695022.7370] device (eth0): state change: unavailable -> disconnected (reason 'carrier-changed', sys-iface-state: 'managed')
Aug 28 15:57:02 mynas kernel: [  327.420987] rk_gmac-dwmac fe300000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
Aug 28 15:57:02 mynas kernel: [  327.421037] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Aug 28 15:57:02 mynas NetworkManager[1659]: <info>  [1661695022.7393] policy: auto-activating connection 'Armbian ethernet' (9362e2eb-3533-439f-acd4-3804f33c01a5)
Aug 28 15:57:02 mynas NetworkManager[1659]: <info>  [1661695022.7409] device (eth0): Activation: starting connection 'Armbian ethernet' (9362e2eb-3533-439f-acd4-3804f33c01a5)
Aug 28 15:57:02 mynas NetworkManager[1659]: <info>  [1661695022.7413] device (eth0): state change: disconnected -> prepare (reason 'none', sys-iface-state: 'managed')
Aug 28 15:57:02 mynas NetworkManager[1659]: <info>  [1661695022.7425] manager: NetworkManager state is now CONNECTING
Aug 28 15:57:02 mynas NetworkManager[1659]: <warn>  [1661695022.7434] platform-linux: do-change-link[2]: failure changing link: failure 16 (Device or resource busy)
Aug 28 15:57:02 mynas kernel: [  327.429651] rk_gmac-dwmac fe300000.ethernet eth0: Link is Down
Aug 28 15:57:02 mynas NetworkManager[1659]: <warn>  [1661695022.7460] platform-linux: do-change-link[2]: failure changing link: failure 99 (Cannot assign requested address)
Aug 28 15:57:02 mynas NetworkManager[1659]: <warn>  [1661695022.7461] device (eth0): set-hw-addr: failed to set-cloned MAC address to AB:CD:47:11:FE:D0 (AB:CD:47:11:FE:D0) (NME_UNSPEC)
Aug 28 15:57:02 mynas kernel: [  327.433545] rk_gmac-dwmac fe300000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211E Gigabit Ethernet] (irq=POLL)
Aug 28 15:57:02 mynas kernel: [  327.484253] rk_gmac-dwmac fe300000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
Aug 28 15:57:02 mynas kernel: [  327.495328] rk_gmac-dwmac fe300000.ethernet eth0: No Safety Features support found
Aug 28 15:57:02 mynas kernel: [  327.495354] rk_gmac-dwmac fe300000.ethernet eth0: PTP not supported by HW
Aug 28 15:57:02 mynas kernel: [  327.495370] rk_gmac-dwmac fe300000.ethernet eth0: configuring for phy/rgmii link mode
Aug 28 15:57:02 mynas NetworkManager[1659]: <info>  [1661695022.8109] device (eth0): state change: prepare -> failed (reason 'config-failed', sys-iface-state: 'managed')
Aug 28 15:57:02 mynas NetworkManager[1659]: <info>  [1661695022.8121] manager: NetworkManager state is now DISCONNECTED
Aug 28 15:57:02 mynas NetworkManager[1659]: <warn>  [1661695022.8128] device (eth0): Activation: failed for connection 'Armbian ethernet'
Aug 28 15:57:02 mynas NetworkManager[1659]: <info>  [1661695022.8139] device (eth0): state change: failed -> disconnected (reason 'none', sys-iface-state: 'managed')
Aug 28 15:57:08 mynas NetworkManager[1659]: <info>  [1661695028.8165] device (eth0): state change: disconnected -> unavailable (reason 'carrier-changed', sys-iface-state: 'managed')

 

I see the error, but I have no idea, what to do.

This thread is quite old. Please consider starting a new thread rather than reviving this one.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...

Important Information

Terms of Use - Privacy Policy - Guidelines