Jump to content

U-Boot Verifying Checksum ... Bad Data CRC


piknew

Recommended Posts

  

I had to reapply u-boot image. So, I did it by armbian-config and later by "dd" command. In both situations this is failing (please see u-boot messages printed by serial). I was restoring the image (I have backup images of my SD card) and trying again. What may be the problem? I had linux-u-boot-orangepi*-current 22.08.6 installed.

 

As below - please note Verifying Checksum ... Bad Data CRC

 

BTW. I tried the same on Orange Pi PC and Orange Pi Zero - the same result (fail to boot).


 

=> version
U-Boot 2022.07-armbian (Oct 18 2022 - 07:35:20 +0000) Allwinner Technology

arm-none-linux-gnueabihf-gcc (GNU Toolchain for the A-profile Architecture 9.2-2019.12 (arm-9.10)) 9.2.1 20191025
GNU ld (GNU Toolchain for the A-profile Architecture 9.2-2019.12 (arm-9.10)) 2.33.1.20191209
=> reset
resetting ...

U-Boot SPL 2022.07-armbian (Oct 18 2022 - 07:35:20 +0000)
DRAM: 1024 MiB
Trying to boot from MMC1


U-Boot 2022.07-armbian (Oct 18 2022 - 07:35:20 +0000) Allwinner Technology

CPU:   Allwinner H3 (SUN8I 1680)
Model: Xunlong Orange Pi PC
DRAM:  1 GiB
Core:  65 devices, 18 uclasses, devicetree: separate
WDT:   Not starting watchdog@1c20ca0
MMC:   mmc@1c0f000: 0
Loading Environment from FAT... Unable to use mmc 0:1...
In:    serial@1c28000
Out:   serial@1c28000
Err:   serial@1c28000
Net:   phy interface1
eth0: ethernet@1c30000
starting USB...
Bus usb@1c1a000: USB EHCI 1.00
Bus usb@1c1a400: USB OHCI 1.0
Bus usb@1c1b000: USB EHCI 1.00
Bus usb@1c1b400: USB OHCI 1.0
Bus usb@1c1c000: USB EHCI 1.00
Bus usb@1c1c400: USB OHCI 1.0
Bus usb@1c1d000: USB EHCI 1.00
Bus usb@1c1d400: USB OHCI 1.0
scanning bus usb@1c1a000 for devices... 1 USB Device(s) found
scanning bus usb@1c1a400 for devices... 1 USB Device(s) found
scanning bus usb@1c1b000 for devices... 1 USB Device(s) found
scanning bus usb@1c1b400 for devices... 1 USB Device(s) found
scanning bus usb@1c1c000 for devices... 1 USB Device(s) found
scanning bus usb@1c1c400 for devices... 1 USB Device(s) found
scanning bus usb@1c1d000 for devices... 1 USB Device(s) found
scanning bus usb@1c1d400 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot:  0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found U-Boot script /boot/boot.scr
3708 bytes read in 5 ms (723.6 KiB/s)
## Executing script at 43100000
U-boot loaded from SD
Boot script loaded from mmc
212 bytes read in 4 ms (51.8 KiB/s)
13021622 bytes read in 549 ms (22.6 MiB/s)
8387760 bytes read in 356 ms (22.5 MiB/s)
Found mainline kernel configuration
32077 bytes read in 13 ms (2.4 MiB/s)
374 bytes read in 10 ms (36.1 KiB/s)
Applying kernel provided DT overlay sun8i-h3-i2c0.dtbo
393 bytes read in 5 ms (76.2 KiB/s)
Applying user provided DT overlay ds1307.dtbo
4185 bytes read in 9 ms (454.1 KiB/s)
Applying kernel provided DT fixup script (sun8i-h3-fixup.scr)
## Executing script at 44000000
Kernel image @ 0x42000000 [ 0x000000 - 0x7ffcb0 ]
## Loading init Ramdisk from Legacy Image at 43400000 ...
   Image Name:   uInitrd
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    13021558 Bytes = 12.4 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... Bad Data CRC
Ramdisk image is corrupt or invalid
SCRIPT FAILED: continuing...
No EFI system partition
BootOrder not defined
EFI boot manager: Cannot load any image

Device 0: unknown device
ethernet@1c30000 Waiting for PHY auto negotiation to complete. done
BOOTP broadcast 1
DHCP client bound to address 192.168.10.136 (3 ms)
*** ERROR: `serverip' not set
Cannot autoload with TFTPGET
missing environment variable: pxeuuid
Retrieving file: pxelinux.cfg/01-02-81-a9-fc-f7-d9
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/C0A80A88
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/C0A80A8
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/C0A80A
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/C0A80
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/C0A8
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/C0A
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/C0
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/C
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/default-arm-sunxi-sunxi
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/default-arm-sunxi
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/default-arm
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/default
*** ERROR: `serverip' not set
Config file not found
BOOTP broadcast 1
DHCP client bound to address 192.168.10.136 (3 ms)
*** ERROR: `serverip' not set
Cannot autoload with TFTPGET
BOOTP broadcast 1
DHCP client bound to address 192.168.10.136 (2 ms)
*** ERROR: `serverip' not set
Cannot autoload with TFTPGET
=>

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...

Important Information

Terms of Use - Privacy Policy - Guidelines