Unable to make it to work: RTC module ds3231, BPI M2Z and ARMBIAN Bookworm

[Ed van den Enden]

I'm unable to make an RTC module to work:
RTC module ds3231, BPI M2Z and ARMBIAN Bookworm
i2c pins 3 and 5
Driver RTC-ds1307 loaded, because RTC-ds3231 is not available.

 

Why do I need a RTC-module?

Often in the field I'm not online but I do need the right time on my observation camera's.

My application does not allow me for having a monitor.

My system does the recordings by motion detection, and the recordings do need the right time on it. 

 

armbian-config
i2c0 set

 

Tools installed:

apt install python3-smbus i2c-tools

 

i2cdetect -y 0
Detects address 068 and not UU as proof of driver been loaded

 

File "hwclock-set" adapted

#if [ -e /run/systemd/system ] ; then

# exit 0

#fi

 

Fake hwclock removed

sudo apt -y remove fake-hwclock

sudo update-rc.d -f fake-hwclock remove

 

armbianEnv.txt
overlay and dtoverlay correctly set

 

modules.conf added:
rtc-ds1307

 

Still, after a power down, the hardware clock shows 1970 as the date

The same module tested on my RPi Zero 2W, and all is working perfect.

 

If somebody can help me, that would be wonderful.

 

 

[IBV]

Hi,

 

is the hardware clock set before power off ?

What does "sudo hwclock" say ?

Why did you modify the hwclock-set script ?

[Ed van den Enden]

Indeed, the hardware clock has been set and checked before power off.

1) date -s "April 22, 2024 11:54:00"

2) hwclock -w

3) hwclock -r

4) battery hwclock 3.6V

5) works flawless with RPi Zero 2W

6) i2cdetect -y 0 shows address 068

 

Why did you modify the hwclock-set script ?
Suggested by many, but without modifying this script, it does not change mallfunction of the hwclock.

 

When connected to WiFi

hwclock --verbose tells me following:

hwclock from util-linux 2.38.1
System Time: 1745389217.903091
Trying to open: /dev/rtc0
Using the rtc interface to the clock.
Last drift adjustment done at 1745317708 seconds after 1969
Last calibration done at 1745317708 seconds after 1969
Hardware clock is on UTC time
Assuming hardware clock is kept in UTC time.
Waiting for clock tick...
...got clock tick
Time read from Hardware Clock: 2025/04/23 06:20:20
Hw clock time : 2025/04/23 06:20:20 = 1745389220 seconds since 1969
Time since last adjustment is 71512 seconds
Calculated Hardware Clock drift is 0.000000 seconds
2025-04-23 08:20:18.895813+02:00

 

After power down and When disconnected from WiFi (my application and so the reason why I need a hwclock to work)

hwclock --verbose tells me following:

hwclock from util-linux 2.38.1
System Time: 1745389772.399976
Trying to open: /dev/rtc0
Using the rtc interface to the clock.
Last drift adjustment done at 1745317708 seconds after 1969
Last calibration done at 1745317708 seconds after 1969
Hardware clock is on UTC time
Assuming hardware clock is kept in UTC time.
Waiting for clock tick...
...got clock tick
Time read from Hardware Clock: 1970/01/01 00:04:02
Hw clock time : 1970/01/01 00:04:02 = 242 seconds since 1969
Time since last adjustment is 1745317466 seconds
Calculated Hardware Clock drift is 0.000000 seconds
1970/01/01 01:04:00.760027+01:00

[IBV]

This would suggest that the battery of the rtc is dead, but it is confusing because you say it works with RPI zero.

Could you provide logs with
 

sudo armbianmonitor -u

 

[Ed van den Enden]

See link

https://paste.armbian.com/alehuretiw
Now connected to WiFi

Edited 9 hours ago by Ed van den Enden

[Ed van den Enden]

Just measured again the battery on the battery pins of the RTC-ds3231, and it shows me 3.6 volt (not the BPI 3.3 volt pins (1 + 9)

[IBV]

After boot, can you show the output of "timedatectl status" ?

[Ed van den Enden]

When connected to WiFi

 

root@clearview:~# timedatectl status
               Local time: Wed 2025-04-23 09:56:59 CEST
           Universal time: Wed 2025-04-23 07:56:59 UTC
                 RTC time: Wed 2025-04-23 07:56:58
                Time zone: Europe/Brussels (CEST, +0200)
System clock synchronized: no
              NTP service: active
          RTC in local TZ: no

 

After power down and disconnected from WiFi

 

root@clearview:~# timedatectl status
               Local time: Wed 2025-04-23 10:04:43 CEST
           Universal time: Wed 2025-04-23 08:04:43 UTC
                 RTC time: Wed 1970-01-01 00:02:45
                Time zone: Europe/Brussels (CEST, +0200)
System clock synchronized: no
              NTP service: active
          RTC in local TZ: no

[Ed van den Enden]

To my understanding and the documentation I found, by investigating the RTC address, with the outcome 068, it indicates that the RTC driver is not loaded, otherwise the address request would show UU as outcome.

[IBV]

There seems to be a RTC detected on boot

 

[    1.018029] sun6i-rtc 1f00000.rtc: registered as rtc0
[    1.018081] sun6i-rtc 1f00000.rtc: setting system clock to 1970-01-01T00:00:04 UTC (4)

 

Just to confirm, you could disconnect your RTC and boot again. Then check the boot log if the system says anything about rtc.

[Ed van den Enden]

Another remark/question:
The latest Armbian does not show a driver RTC-ds3231, just the RTC-ds1307 driver.

Therefore I used fo my ds3231 RTC module the available driver RTC-ds1307.
Could that be the reason for the malfunction of the hwclock?

 

Edited 7 hours ago by Ed van den Enden

[Ed van den Enden]

The below output with the RTC module taken off the BPI M2Z

Further below I saw that there were some pin errors. (most probably nothing to do with this topic)

 

https://paste.armbian.com/axoduwanuq
 

[ 1.020506] usbcore: registered new interface driver usb-storage

[ 1.022284] sun6i-rtc 1f00000.rtc: registered as rtc0

[ 1.022371] sun6i-rtc 1f00000.rtc: setting system clock to 1970-01-01T00:00:04 UTC (4)

[ 1.023147] i2c_dev: i2c /dev entries driver

[ 1.025025] sunxi-wdt 1c20ca0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)

 

 

 

[ 7.721526] sun8i-h3-pinctrl 1c20800.pinctrl: pin PD14 already requested by onewire@0; cannot claim for pps@0

[ 7.721577] sun8i-h3-pinctrl 1c20800.pinctrl: pin-110 (pps@0) status -22

[ 7.721597] sun8i-h3-pinctrl 1c20800.pinctrl: could not request pin 110 (PD14) from group PD14 on device 1c20800.pinctrl

[ 7.721613] pps-gpio pps@0: Error applying setting, reverse things back

[Ed van den Enden]

I notice that there is a linux driver available at GITHUB for the ds3231, but I have no clue how to compile/install this driver.

https://github.com/AxelElRojo/ds3231-linux

 

[IBV]

I believe the rtc_ds1307 is compatible with the ds3231.

You can check that with "modinfo rtc_ds1307"

 

1 hour ago, Ed van den Enden said:

[ 7.721526] sun8i-h3-pinctrl 1c20800.pinctrl: pin PD14 already requested by onewire@0; cannot claim for pps@0

[ 7.721577] sun8i-h3-pinctrl 1c20800.pinctrl: pin-110 (pps@0) status -22

[ 7.721597] sun8i-h3-pinctrl 1c20800.pinctrl: could not request pin 110 (PD14) from group PD14 on device 1c20800.pinctrl

[ 7.721613] pps-gpio pps@0: Error applying setting, reverse things back

I don't know the hardware, can you check that you don't have pin conflicts?

Do you need these overlays : "pps-gpio w1-gpio" ? If not, you might remove them from armbianEnv.txt, boot and check again.

[Ed van den Enden]

Indeed, the rtc_ds1307 is compatible with the ds3231 and removing pps-gpio w1-gpio did the errors disappear.

 

The RTC module still doesn't work.

😭

 

 

 

[IBV]

Try to enable i2c1 also (just a stupid suggestion) in armbianEnv.txt and scan the bus with i2cdetect. Who knows, maybe there's a weird mapping of the bus interfaces.

[IBV]

 

6 hours ago, Ed van den Enden said:

i2cdetect -y 0 shows address 068

This should mean that the rtc is there.

Take a look at https://wiki.banana-pi.org/BPI_RTC_real_time_Module

 

You could try:

echo ds3231 0x68 > /sys/class/i2c-adapter/i2c-0/new_device

 

Then a dmesg to see if there's something new about rtc.

[Ed van den Enden]

Nop, that didn't work

had also both i2c0 and i2c1 activated

 

root@clearview:~# i2cdetect -y 0
     0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
00:                         -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: 30 -- 32 33 34 35 36 -- -- -- -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
50: 50 51 52 53 54 55 56 57 58 59 5a 5b 5c 5d 5e 5f
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --
root@clearview:~# i2cdetect -y 1
Error: Could not open file `/dev/i2c-1' or `/dev/i2c/1': No such file or directory
root@clearview:~# ls /dev/i2c-*
/dev/i2c-0
 

[Ed van den Enden]

I will leave it for what it is for now.

I will move back to RPi zero 2W, solder an antenna, and I'm good to go.

Would have loved to go to the BPI m2z and later to the BPI m4z, but for now not an option.

By the way, with the latest Armbian upgrade an hour ago, my USB camera is also not working anymore.

Thank you very much for the support.

Kind regards,

Ed👏

Edited 3 hours ago by Ed van den Enden