Bridged AP does not work on BananaPiPro (Armbian_community_26.8.0-trunk.170_Bananapipro_trixie_current_6.18.35_minimal)

[loeriver]

Armbianmonitor:

https://paste.armbian.com/fawolicoki

I tried to build an bridged AP so that I can reach the Internet from a WiFi net spawned from the BananaPiPro. By this I followed the procedure from armbian-config (config.network.sh).

 

After install the AP is shown in the login screen:

 

WiFi AP:      SSID: (BPi), channel 7 (2442 MHz), width: 20 MHz, center1: 2442 MHz

 

When I try to connect from my mobile phone it either says "connecting without Internet".

The output in syslog is then:

 

026-07-06T12:35:02.645970+02:00 bananapipro hostapd: wlan0: STA 22:50:7b:ac:e3:2e IEEE 802.11: associated
2026-07-06T12:35:02.690671+02:00 bananapipro hostapd: wlan0: STA 22:50:7b:ac:e3:2e RADIUS: starting accounting session 500A81EDD1715454
2026-07-06T12:35:02.691497+02:00 bananapipro hostapd: wlan0: STA 22:50:7b:ac:e3:2e WPA: pairwise key handshake completed (RSN)

 

Ort otherwise the phone just says "cannot connect".

 

My netplan file is as follows:

 

network:
  version: 2
  renderer: networkd
  ethernets:
    end0:
      dhcp4: false
      dhcp6: false
      macaddress: "02:cd:08:83:3c:f3"
    wlan0:
      dhcp4: false
      dhcp6: false
  bridges:
    br0:
      addresses:
      - "192.168.178.29/24"
      nameservers:
        addresses:
        - 9.9.9.9
        - 1.1.1.1
      interfaces:
      - wlan0
      - end0
      routes:
      - metric: 200
        to: default
        via: "192.168.178.1"

 

The hostapd.conf is:

 

interface=wlan0
driver=nl80211
ssid=BPi
hw_mode=g
channel=7
wmm_enabled=0
macaddr_acl=0
auth_algs=1
ignore_broadcast_ssid=0
wpa=2
wpa_passphrase=secret
wpa_key_mgmt=WPA-PSK
wpa_pairwise=TKIP
rsn_pairwise=CCMP

ctrl_interface=/var/run/hostapd
ctrl_interface_group=0

ieee80211n=1
ht_capab=[DSSS_CK-40][HT20+]

preamble=1

bridge=br0

 

The output of network list is:

 

root@bananapipro:/etc/hostapd# networkctl list
IDX LINK  TYPE     OPERATIONAL SETUP     
  1 lo    loopback carrier     unmanaged
  2 end0  ether    enslaved    configured
  3 br0   bridge   routable    configured
  4 wlan0 wlan     enslaved    failed   

 

Does anybody have an idea where to look further for a solution? As I have an AP running on my other BananaPiPro (Bookworm CLI / Networkmanager, manual config, not bridged) it cannot be a complete HW limitation, I think.

[eselarm]

I had a quick look at the script, but it is too complex for me to see what could be wrong. Also there is netplan layer in between that I am not familiar with anymore. Maybe you can look at what is generated in terms of systemd-networkd files (e.g. in /etc/systemd/network/ ). And also use commands like ip route etc to see the actual state.

 

Edited 5 hours ago by eselarm

[loeriver]

Well, netplan is the advertised / provided solution for Armbian. So when you look into /etc/systemd/network you find a readme from armbian pointing you to /etc/netplan. I think what netplan does is generating the following files for systemd-networkd under /run/systemd/network:

 

10-netplan-end0.network:

[Match]
Name=end0

[Link]
MACAddress=02:cd:08:83:3c:f3

[Network]
LinkLocalAddressing=no
Bridge=br0

 

10-netplan-wlan0.network

[Match]
Name=wlan0

[Network]
LinkLocalAddressing=no
Bridge=br0

 

10-netplan-br0.network 

[Match]
Name=br0

[Network]
LinkLocalAddressing=ipv6
Address=192.168.178.29/24
DNS=9.9.9.9
DNS=1.1.1.1
ConfigureWithoutCarrier=yes

[Route]
Destination=0.0.0.0/0
Gateway=192.168.178.1
Metric=200

 

10-netplan-br0.netdev 

[NetDev]
Name=br0
Kind=bridge

 

And this is the ip output:

 

ip route:

default via 192.168.178.1 dev br0 proto static metric 200 
192.168.178.0/24 dev br0 proto kernel scope link src 192.168.178.29 

ip link:

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: end0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq master br0 state UP mode DEFAULT group default qlen 1000
    link/ether 02:cd:08:83:3c:f3 brd ff:ff:ff:ff:ff:ff
    altname enx02cd08833cf3
3: br0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT group default qlen 1000
    link/ether a2:67:ed:53:cb:f1 brd ff:ff:ff:ff:ff:ff
4: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master br0 state UP mode DEFAULT group default qlen 1000
    link/ether e0:76:d0:03:53:bc brd ff:ff:ff:ff:ff:ff
    altname wlxe076d00353bc

 

 

[eselarm]

I made a comparable setup on a raspberrypi3b+ and I see in the journal:

Jul 07 17:37:01 raspi7 systemd-networkd[292]: wlan0: Configuring with /etc/systemd/network/10-wlan0.network.
Jul 07 17:37:01 raspi7 systemd-networkd[292]: wlan0: Failed to set master interface: Device does not allow enslaving to a bridge. Operation not supported
Jul 07 17:37:01 raspi7 systemd-networkd[292]: wlan0: Failed

It worked many years ago when it was buster or bullseye and using ifupdown interfaces network setup. Also ported that to NetworkManager before Bookworm and that works, also in Trixie.

 

This is my first manual setup, as it is Debian Trixie based, I can avoid the use of netplan.io. I remember I have seen this issue somewhere, It might be a newer release systemd issue. But have not searched internet now, will see later why this is.

Edited 1 hour ago by eselarm