Zhexue.

Hey Igor, Can I take the image for RaspBerry PI4 from this website (https://github.com/armbian/community) for the PI3 board or is there another version somewhere? Kind regards Z. Matthias

Hello all, As I have often said, I am very satisfied with this LINUX implementation on the RASPI PI4 board. In the meantime, I noticed one small thing and that was somehow related to the 4GB version of my RASPI. I often had to record a KERNEL crash here; this did not happen under the 8GB version until now. But now to my actual question: How can I activate the CAMERA port under this Linux version so that I can connect a camera there? Best regards Z. Matthias

Thanks @Igor. I would like to check it and give you an feedback.

Hello all, according to the hints on the ARMBIAN homepage the image "Armbian_23.02.0-trunk_Rpi4b_lunar_edge_6.1.5.img" should work with the Raspi 3. Unfortunately it does not work properly, the system does not want to boot with it.... The name of the image says that it was generated for Raspi4, but -as I said- the homepage says that this image would also be compatible for the other Raspberry systems mentioned there. Can anyone tell me what the reason could be, because I would love to use this ingenious image for the Raspi 3. Best regards from Berlin Z. Matthias

Hello all, I have installed the image "Armbian 23.02.0-trunk.0176 Lunar with bleeding edge Linux 6.1.6-bcm2711" on my two Raspi 4 systems. One system runs via cable and the other via WLAN. At the beginning there were some problems with the IPv6 - kernel, if "apt update" was executed. I got this problem under control with "disable ipv6".... Since then, both systems run flawlessly & without problems. With the implementation of GPIO you should fall back on an existing GPIO - version, which works in any case also under this image; also for 64bit. One small thing I would like to know very much, because on the system with the cable the WaveShare PoE - HAT is installed and I would like to monitor via software very much the FAN. Unfortunately, this does not work because the software does not see "I2C". In the Config - File, however, you see this as "enable" - What can I do here? Does anyone have an idea how I can enablen the I2C so that this works? Best regards from Germany..... Z. Matthias

Hey JMCC, thank you so much for your help. But I can't find this file: media-buster-legacy-rk3399 So, what can I do now? IS there any other subjects or ideas? best regards from Berlin Z. Matthias

Hey Werner, this is the NoIR - Camera from Raspberry (original). Best regards Z. Matthias

Hey Werner, thank you very much for this help. And YES, that was it. In first time, I disable the following 2 Services: * armbian-ramlog.service * armbian-zram-config.service With ONLY disabling the service "armbian-zram-config.service", it was not enough. But now, it is work and I am happy, because one of my system has still shutdown this night while the volume "/var/log" is going to 100%.... Thank you very much for your help... Z. Matthias

Hello all, I have a question today regarding ARMBIAN - Linux and the configuration of the ZRAM .... Under the ARMBIAN for RockPI 4 I have a ZRAM for the SWAP and a ZRAM for /var/log. Is it possible that I change this configuration and use the eMMC memory for these two areas? Because the big problem with /var/log is that it is simply too small and thus constantly runs into "ERROR" -> volume full. Thank you very much and I am looking forward to constructive contributions to solve my problem. Kind regards

Hello all, I wanted to start using the camera on my RockPI 4B today, but unfortunately I can't find an entry for it under "armbian-config" and under "boot/config*" I personally can't clearly identify the setting/parameter for it. Can you please help me with this? That would be very helpful for me, thank you. Kind regards Z. Matthias

Hello all, I have a RockPi 4B in use and wanted to connect my 7" display from Raspberry via the display port. According to these instructions, it should also work. https://wiki.radxa.com/Rockpi4/hardware/display#Raspberry_Pi_7_inch_Touch_Display But unfortunately I can't find this file under "boot" because I'm using an ARMBIAN image. How can I address this 7" display? Can anyone help me here? Best regards from Berlin Z. Matthias

Hello together, I have a RockPI 4B board with the extension for M.2 SSD applications. I wanted to install a 120 GB SSD disk, but unfortunately I cannot find it under "fdisk -l". Can anyone help me here with what I can do? Are there any tricks or the like to make this work? Kind regards Z. Matthias

Thanks Igor, I look after the setting for the fans myself, for example, but it could have been that by chance the person knows what he did differently, for example, in the 4 - images, than in the 5 - image. I also wanted to point out with it also only that I noticed there. It should not come across as a reproach and kind of command from me. For it I maich much too long already around in the computer science, in order to know, what that means. I, for example, have always been grateful for such hints. Nevertheless, my extraordinary thanks again to all of you that you deliver a super JOB with the creation of such an image. Thanks for everything & please, if I can help you in any way, feel free to contact me.

...BUT! It's only work with these two images: Armbian_21.08.0-trunk_Jetson-nano_buster_current_5.10.43.img Armbian_21.08.0-trunk_Jetson-nano_buster_legacy_4.9.140.img NOT with the DESKTOP - Images or any other images. I've tested these all of functionality with WLAN. Is there any information about the FAN-Connector? Because on the Image: Armbian_21.08.0-trunk_Jetson-nano_buster_legacy_4.9.140.img it's work directly from startup and on all the other images NOT. Best regards from Berlin Matthias

Hello together, Yes it seems that the firmware "iwlwifi" was not installed. If I install this firmware I saw, that "wlan0" is enable. Please careful about "wpa_supplicant.conf" -> it doesn't need Country or anything else. Only the "network - Setup" is necessary. Thank' s all for your help....

This is a little bit difficult. It is not better to deinstall the software for WIFI (Firmware) and install it again?

Hello together, I'm using this board inclusive PoE - Board with the ARMBIAN - Image. Now I have a question about the FAN on this PoE - Board. Does anyone know, how can I enable the FAN permanently, because the heat from the CPU is to high and I don't want to kill this board with overheating..... Best regards Matthias

With XUBUNTU, NVIDIA it's work very well. It seems, that this image has no driver like ./sys/devices/1003000.pcie/pci0000:00/0000:00:02.0/0000:02:00.0/net/eth0 ./sys/class/net/eth0 I can send you one M2.Wifi - Module for helping and spending. Because for me it is really important. How we can do that? How can I help you here more? in the "/boot" - directory there's a file with extension .example and I saw, that there must be "WLAN" to enable for the first running.... But I can't modify the image.

...additional information: if I want to search for wlan0 with: find . -name wlan0 -print, the system show me nothing if I do the same with eth0, I´ve got this: ....... ./sys/devices/1003000.pcie/pci0000:00/0000:00:02.0/0000:02:00.0/net/eth0 ./sys/class/net/eth0 I think, there are no drivers build for using wlan0, or?

Hey, thank you for your INFO about the releases. Now, I have installed the 4.9 - Kernel on my nano.jetson - Board and I see now the following information: 01:00.0 Network controller: Intel Corporation Wireless 8265 / 8275 (rev 78) Subsystem: Intel Corporation Wireless 8265 / 8275 (Dual Band Wireless-AC 8265) Flags: fast devsel, IRQ 84 Memory at 13000000 (64-bit, non-prefetchable) Capabilities: [c8] Power Management version 3 Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [40] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Device Serial Number 40-1c-83-ff-ff-42-2d-9f Capabilities: [14c] Latency Tolerance Reporting Capabilities: [154] L1 PM Substates Kernel modules: iwlwifi with the command: iwconfig eth0 no wireless extensions. lo no wireless extensions. with the command: wpa_supplicant -i wlan0 -c /etc/wpa_supplicant/wpa_supplicant.conf Successfully initialized wpa_supplicant Could not read interface wlan0 flags: No such device nl80211: Driver does not support authentication/association or connect commands nl80211: deinit ifname=wlan0 disabled_11b_rates=0 Could not read interface wlan0 flags: No such device wlan0: Failed to initialize driver interface or with: wpa_supplicant -i nl80211 -c /etc/wpa_supplicant/wpa_supplicant.conf Successfully initialized wpa_supplicant Could not read interface nl80211 flags: No such device nl80211: Driver does not support authentication/association or connect commands nl80211: deinit ifname=nl80211 disabled_11b_rates=0 Could not read interface nl80211 flags: No such device nl80211: Failed to initialize driver interface the command: nmcli device show GENERAL.DEVICE: eth0 GENERAL.TYPE: ethernet GENERAL.HWADDR: 00:04:4B:E6:6C:C2 GENERAL.MTU: 1500 GENERAL.STATE: 100 (verbunden) GENERAL.CONNECTION: eth0 GENERAL.CON-PATH: /org/freedesktop/NetworkManager/ActiveConnection/1 WIRED-PROPERTIES.CARRIER: an IP4.ADDRESS[1]: 192.168.178.50/24 IP4.GATEWAY: 192.168.178.1 IP4.ROUTE[1]: dst = 192.168.178.0/24, nh = 0.0.0.0, mt = 0 IP4.ROUTE[2]: dst = 0.0.0.0/0, nh = 192.168.178.1, mt = 0 IP4.ROUTE[3]: dst = 169.254.0.0/16, nh = 0.0.0.0, mt = 1000 IP6.GATEWAY: -- GENERAL.DEVICE: lo GENERAL.TYPE: loopback GENERAL.HWADDR: 00:00:00:00:00:00 GENERAL.MTU: 65536 GENERAL.STATE: 10 (nicht verwaltet) GENERAL.CONNECTION: -- GENERAL.CON-PATH: -- IP4.ADDRESS[1]: 127.0.0.1/8 IP4.GATEWAY: -- IP6.GATEWAY: -- Which device-name did you get the WLAN - Module? I can't attach the WLAN - Device with every part of commands..... How can I help you /us for solving this problem? What I find out is, that my FAN works with 4.9 directly and with 5er NOT. Best regards Matthias

Hey, thank you for your INFO about the releases. Now, I have installed: Welcome to Armbian 21.08.0-trunk Buster with Linux 5.10.43-station on my nano.jetson - Board and I see now the following information: lspci -v 01:00.0 Network controller: Intel Corporation Wireless 8265 / 8275 (rev 78) Subsystem: Intel Corporation Wireless 8265 / 8275 (Dual Band Wireless-AC 8265) Flags: fast devsel, IRQ 18 Memory at 13000000 (64-bit, non-prefetchable) Capabilities: [c8] Power Management version 3 Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [40] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Device Serial Number 40-1c-83-ff-ff-42-2d-9f Capabilities: [14c] Latency Tolerance Reporting Capabilities: [154] L1 PM Substates Kernel modules: iwlwifi It seems like good, but I can't match this Controller to an device. It is necessary, that I must change anything on "boot-config" or how can I enable this interface now with this Kernel? Or should I reinstall the other on with 4.9 - Kernel to check that? Best regards Matthias

Okay, Thanks. I will try it till next week and give you some feedbacks....

Yes, that is correct

About this Module: 01:00.0 Network controller: Intel Corporation Wireless 8265 / 8275 (rev 78) Subsystem: Intel Corporation Wireless 8265 / 8275 (Dual Band Wireless-AC 8265) This is an additional board for Jetson Nano 4GB ...

Good Morning all. I am really very enthusiastic about your LINUX package for JetSon Nano. It's very fast and very stable. Since I am using this board in a project for autonomous driving and it is installed on the WaveShare kit, I would also like to activate the WLAN module, but unfortunately it keeps failing. With the command: lspic -k I can see the board, but you can also see that the driver is not installed. lspci -k 00:01.0 PCI bridge: NVIDIA Corporation Device 0fae (rev a1) Kernel driver in use: pcieport 00:02.0 PCI bridge: NVIDIA Corporation Device 0faf (rev a1) Kernel driver in use: pcieport 01:00.0 Network controller: Intel Corporation Wireless 8265 / 8275 (rev 78) Subsystem: Intel Corporation Wireless 8265 / 8275 (Dual Band Wireless-AC 8265) 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 15) Subsystem: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller Kernel driver in use: r8169 Kernel modules: r8169 I also tried to install these drivers using "apt install firmware-iwlwifi". The system does this, but does not create a new kernel and I cannot find anything in the relevant directory .... What else can I do? For me this is really important, because the "overhead" for the NVIDIA package is simply too big for testing and development with far too much BALAST .... I would really be very grateful if you could help me here quickly. Thank you in advance..... Matthias