inos

yes it works - thank you very much!!!

Thank's for the quick reply! I'll try the nightly build but it's not time-critical so don't rush!

it seems that the kernel-header version is not updated to the actual kernel version: $ uname -a Linux cubietruck 4.14.65-sunxi #11 SMP Tue Aug 21 10:02:12 CEST 2018 armv7l GNU/Linux install header using armbian-config tool doesn't work - no error message thereafter: installed header manually: linux-headers-next-sunxi dpkg: warning: version '4.14.18-sunxi 4.14.65' has bad syntax: invalid character in revision number Building for 4.14.65-sunxi Module build for kernel 4.14.65-sunxi was skipped since the kernel headers for this kernel does not seem to be installed.

I have built a rock64 stretch image and found in syslog: localhost cron[757]: (*system*armbian-updates) INSECURE MODE (group/other writable) (/etc/cron.d/armbian-updates) could be fixed with: sudo chmod 644 /etc/cron.d/armbian-updates

Thank you for the quick reply. I will try to compile a image on my own and report... EDIT: I built the image (stretch/legacy kernel) on my own it works without any problems until now.

Thank's for supporting Rock64! Is there a chance for a debian server image (beta) within the near future? All my boards are running a armbian debian OS and I would like to stay consistent here... Best regards Martin

I own an Odroid u3 board as well and I would highly appreciate, if there would be an image available. I am using armbian on cubietruck and I am very happy with this distribution. Thank's very much to the team! Martin

First of all, thank you very much for the great work! On cubietruck after upgrade to 5.20, I have some trouble with network bonding. /etc/network/interfaces: auto eth0 iface eth0 inet manual bond-master bond0 bond-primary eth0 bond-mode active-backup auto wlan0 iface wlan0 inet manual wpa-ssid xxxx.xxx wpa-psk xxxxxxxxx bond-master bond0 bond-primary eth0 bond-mode active-backup # Define master auto bond0 iface bond0 inet static address xxx.xxx.xxx.xxx netmask xxx.xxx.xxx.xxx gateway xxx.xxx.xxx.xxx hwaddress ether xx:xx:xx:xx:xx bond-slaves none bond-primary eth0 bond-mode active-backup bond-miimon 100 After booting, the device is not reachable via the LAN unless the wlan0 is down the corresponding log: <6>bonding: bond0: setting mode to active-backup (1). <6>ADDRCONF(NETDEV_UP): bond0: link is not ready <6>bonding: bond0: Adding slave eth0. <6>sunxi_gmac: probed <6>eth0: PHY ID 001cc915 at 0 IRQ 0 (sunxi_gmac-0:00) active <6>eth0: PHY ID 001cc915 at 1 IRQ 0 (sunxi_gmac-0:01) <6>bonding: bond0: making interface eth0 the new active one. <6>bonding: bond0: first active interface up! <6>bonding: bond0: enslaving eth0 as an active interface with an up link. <6>ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready <6>bonding: bond0: Setting eth0 as primary slave. <3>bonding: unable to update mode of bond0 because interface is up. <6>bonding: bond0: Adding slave wlan0. <3>[ap6210] Dongle Host Driver, version 1.28.23.3 (r). <3>[ap6210] Compiled in drivers/net/wireless/ap6210 on Sep 14 2016 at 19:40:55. <3>[ap6210] WLAN going back to live sdio_reset_comm(): <3>[ap6210] dhd_bus_devreset: WLAN ON <3>[ap6210] Final fw_path=/lib/firmware/ap6210/fw_bcm40181a2.bin <3>[ap6210] Final nv_path=/lib/firmware/ap6210/nvram_ap6210.txt <3>[ap6210] download firmware /lib/firmware/ap6210/fw_bcm40181a2.bin <3>[ap6210] Dongle ready, protocol version 4 <3>[ap6210] Dongle ready, protocol version 4 <3>[ap6210] Firmware up: op_mode=0x0005, Broadcom Dongle Host Driver mac=6c:fa:a7:16:12:19 <3>[ap6210] Firmware version = wl0: Mar 10 2014 14:59:50 version 5.90.195.89.18 FWID 01-b13c09c7 <3>[ap6210] Chip: a962 Rev 1 Pkg 9<3>[ap6210] p2p0: p2p_dev_addr=6e:fa:a7:16:12:19 <6>bonding: bond0: enslaving wlan0 as a backup interface with an up link. <6>bonding: bond0: Setting eth0 as primary slave. <6>bonding: bond0: Setting MII monitoring interval to 100. <3>bonding: unable to update mode of bond0 because interface is up. <6>bonding: bond0: Setting eth0 as primary slave. <6>bonding: bond0: link status definitely down for interface eth0, disabling it <6>bonding: bond0: making interface wlan0 the new active one. <6>Installing knfsd (copyright (C) 1996 okir@monad.swb.de). <6>PHY: sunxi_gmac-0:00 - Link is Up<c> - 1000/Full<c> <6>bonding: bond0: link status definitely up for interface eth0, 1000 Mbps full duplex. <6>bonding: bond0: making interface eth0 the new active one. Forgot to mention the WLAN itself (without bonding) works fine. On shutdown or reboot, the device hangs with the following message: <3>[ap6210] wl_event_handler was terminated <6>bonding: bond0: Removing slave wlan0. <6>bonding: bond0: releasing backup interface wlan0 <3>[ap6210] Reason 3 <3>[ap6210] error (-5) <3>[ap6210] dhd_check_hang: Event HANG send up due to re=2 te=0 e=-110 s=2 <3>[ap6210] 'wl bss -C 0' failed: -110 <3>[ap6210] NOTE: this ioctl error is normal when the BSS has not been created yet. <3>[ap6210] dhd_prot_ioctl : bus is down. we have nothing to do <3>[ap6210] wlan0:error(-1) <3>[ap6210] Reason 3 <3>[ap6210] dhd_prot_ioctl : bus is down. we have nothing to do <3>[ap6210] bcmsdh_set_irq Flag = 0 <3>[ap6210] dhd_bus_devreset: WLAN OFF DONE <3>[ap6210] WLAN placed in RESET <3>[ap6210] In : chip crash eventing So shutdown or reboot is possible only after ifconfig wlan0 down Thanks for your help! Martin