Jump to content

Search the Community

Showing results for tags 'nanopct3plus'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Community
    • Announcements
    • Feature Requests
  • Using Armbian
    • Beginners
    • Software, Applications, Userspace
    • Advanced users - Development
  • Upcoming Hardware (WIP)
    • News
    • Odroid M1
    • ROCK 5B
  • Maintained Hardware
    • Board does not start
    • Amlogic meson
    • Allwinner sunxi
    • Marvell mvebu
    • Rockchip
    • Other families
  • Unmaintained (CSC/EOL/TVB) / Other
    • TV boxes
    • Off-topic
    • Amlogic meson
    • Allwinner sunxi
    • Marvell mvebu
    • Rockchip
    • Other families

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


Matrix


Mastodon


IRC


Website URL


XMPP/Jabber


Skype


Github


Discord


Location


Interests

Found 5 results

  1. To Igor Bit not understand why new 5.44 for nanoPC T3 plus not run. I see only first boot screen and then black always ???
  2. I need help please, I am working on NanoPCt3 board based on Armbian_5.83_Nanopct3plus_Ubuntu_bionic_next_4.14.115_desktop I put static ip to eth0 and when i try to ping the output in not stable: 64 bytes from 104.27.115.15 (104.27.115.15): icmp_seq=1 ttl=58 time=580 ms 64 bytes from 104.27.115.15 (104.27.115.15): icmp_seq=2 ttl=58 time=120 ms 64 bytes from 104.27.115.15 (104.27.115.15): icmp_seq=3 ttl=58 time=350 ms and then the output: Destination host unreachable. Destination host unreachable. Destination host unreachable. and i think there are some issues in kernel drivers related on Ethernet or ipv4 so could you please help me to fix Ethernet issue ??
  3. Hello I have a nanoPc t3 plus board and I cannot boot it. I searched and I found a related topic that has the same problem but there is no answer. I believe the problem is because of different mem chip but the same revision (1709) Can boot armbian whit compiled friendlyArm Uboot? topic URL my memory chip picture and logs (from the topic) \
  4. In the nanopcT3+ board I need to enable the I2S1 (14 pin header) in Desktop version. I need to have the I2S1 peripheal as SLAVE and a MCLK of 48kHz and 192kHz (better if other clock speed are supported). The "aplay -l" and "arecord -l" commands must show the I2S1 as a sound card with input ad output device. I've tried to do the job but I'm a newbbie on linux and embedded linux. Following the official FriendlyArm wiki, on a host PC I've downloaded the kernel source, modified the dtsi file to enable i2s, recompiled the kernel and U-boot and all steps seem work fine. Now I don't know how to do a final steps to have a SD bootable image with eflasher to load and test my distro in the NanoPC T3+ emmc. Anyone can explain step by step (from download the source code up to flash the bootable image (also with emmcflasher inside) to SDcard) how to do to enable this feature in Desktop version of Armbian. Thanks in advance!
  5. Hi guys. I can't get the headphone jack to work on the NanoPC T3+ on Armbian 5.44 Bionic. HDMI sound works. There's a second Built-in Audio, but nothing seems to work. Also the on-board microphone doesn't work. I've tested it on the friendlyArm Lubuntu and there it both works. Additional. Can somebody point me into the right direction where to add a higher cpufreq in available frequencies? At 1400Mhz it only reaches 55°C maxed(with fan). Single core performance is bad. So some overclock would be helpful. Otherwise Armbian works great. Thank you. NicoD
×
×
  • Create New...