MoA 0 Posted April 5 Share Posted April 5 Hello all, I need some help. I have a Beelink GT1 Mini TV Box 64GB Gigabit Lan 4 GB Ram. I use this stock firmware: v007P0 stock firmware LPDDR4 version (SN: 95X2) for Beelink GT1 Mini TV Box from here. https://beelink-my.sharepoint.com/:u:/g/personal/firmwareservice_beelink_onmicrosoft_com/EQ8GFfRPJopFoKLfJt71qyMB7ZuofgTb_L3_VW3CHO2g2g?e=Hq70yf https://chinagadgetsreviews.com/download-android-pie-9-v007p0-stock-firmware-for-beelink-gt1-mini-tv-box.html I am trying to flash Armbian_20.10_Arm-64_buster_current_5.9.0.img.xz using the meson-g12a-gt1-mini-a but I get the error here-below: I have tried all other meson-g12a with same result Is it because it has LPDDR4 instead of DDR4 ? Anything I can do to make it work?? Supported API: 3 charge_status 2, charged 1, status SUCCAESS, capacity 100 Finding update package Opening update package E: Block map file too short: 3 E: Map of '@/cache/recovery/block.map' failed E: failed to map file Installation aborted Thanks a lot in advance for your help, MoA, Cheers, Link to post Share on other sites More sharing options...
SteeMan 108 Posted April 9 Share Posted April 9 When you say you are trying to flash Armbian_20.10_Arm-64_buster_current_5.9.0.img.xz what do you mean by that? Specifically what steps are you doing? Are you following the instructions in fhe FAQ: https://forum.armbian.com/topic/17106-installation-instructions-for-tv-boxes-with-amlogic-cpus Link to post Share on other sites More sharing options...
MoA 0 Posted April 11 Author Share Posted April 11 Thanks! I followed a different guide which told me to use the "update software" to load the autoscript.sh (this method actually works for my Vorke S912 Z6 Plus). For the S905x2 Beelink GT1 Mini --> It seems that we have to use the toothpick method! Cheers and thanks again. Link to post Share on other sites More sharing options...
RicardoSA 0 Posted August 3 Share Posted August 3 Hi, I'm trying to flash a GT1 Ultimate and i seam to be getting stuck at a flashing beelink logo. Changed the extlinux.conf to use the gt1 instead and copyed the gt1 file to the root and renamed it. But the only thing i keep getting is the logo as i plug the power on and then goes away and then some times shows up again in the screen. But that's mainly it... Any tips? Using Armbian_20.10_Arm-64_bullseye_current_5.9.0.img.xz Link to post Share on other sites More sharing options...
SteeMan 108 Posted August 3 Share Posted August 3 @RicardoSA What instructions are you following? No current instructions have a step that requires you to copy any file to root. Look at the instructions in the FAQ section of the TV box forum. Link to post Share on other sites More sharing options...
RicardoSA 0 Posted August 4 Share Posted August 4 On 8/3/2021 at 7:54 PM, SteeMan said: @RicardoSA What instructions are you following? No current instructions have a step that requires you to copy any file to root. Look at the instructions in the FAQ section of the TV box forum. Was doing a mix of the old way and the way of that method you mentioned read properly and it worked just fine thank you Link to post Share on other sites More sharing options...
Recommended Posts