Jump to content

Efforts to develop firmware for H96 MAX V56 RK3566 8G/64G

Hqnicolas

By Hqnicolas
in Rockchip CPU Boxes

 Share

Recommended Posts

Hqnicolas

Hqnicolas

Posted
  • Author
Posted (edited)

 

2 hours ago, Vincenzoernst1 said:

question: i see the red EMMC(? its not ethernet.) led blinking all the time. Iotop doesnt show any writes. Is  it a write (access) led?


The RED LED is set on DTS to be HeartBeat: This is the code 

@Vincenzoernst1 if you wanna change it: 

sudo apt update
sudo apt install armbian-config

  

sudo armbian-config


Edit Device tree with armbian config. 

		led_status: led-status {
			label = "led-status";
			gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>;
			linux,default-trigger = "heartbeat";
			pinctrl-names = "default";
			pinctrl-0 = <&led_status_enable_h>;
		};


@Vincenzoernst1 I noticed that you care a lot about the look of the box 
I invite you to participate in the development of This project with @pocosparc

The objective is here

Edited by Hqnicolas
0
Link to comment
Share on other sites

Armbian & Khadas are rewarding contributors

Hqnicolas

Hqnicolas

Posted
  • Author
Posted (edited)

Today I Test the DXVK Wine against wined3d wrapper  
wined3d wrapper by default translate directx calls to the openGL api
and it got Slower on Vulkan
WTF! 

winetricks renderer=vulkan

 

Edited by Hqnicolas
0
Link to comment
Share on other sites
Hqnicolas

Hqnicolas

Posted
  • Author
Posted

Testing "AetherSX2-v1.5-3606.AppImage"
Playstation 2 emulation Isn't compatible at all
it requires OpenGL 3.3 but RK3566 only got 3.1:

glxinfo | grep "OpenGL version"
OpenGL version string: 3.1 Mesa 23.2.1-1ubuntu3.1~22.04.2

AetherSX2 works with Vulkan at 15fps on Guitar Hero II "unplayable"

PS1 emulation works fine with 3x resolution on Retroarch from Snap Store.
all olders emulators works fine

aarch64-retroarch-cores.tar.xz

0
Link to comment
Share on other sites
Hqnicolas

Hqnicolas

Posted
  • Author
Posted (edited)

################# FULL DESKTOP EXAMPLE ################
For the users who bought the device hoping to create a cheap desktop,
here is an image that exemplifies this experience:

 

32gb: Example Desktop Image

64gb: Example Desktop Image

Unzip Method

 

About:
Status: Unsafe (test only)
User: user
Passwd: user
Version: 22.04 (pop)
Language: PT-BR
Device: H96-MAX RK3566

Flash Method: v1.1
After Install:
Resize disc
Change Language

Edited by Hqnicolas
0
Link to comment
Share on other sites
Hqnicolas

Hqnicolas

Posted
  • Author
Posted
40 minutes ago, pessimism said:

card slot part just arrived.  fingers crossed i dont destroy the board trying to solder the TINY pins

 

pre-heat the board before soldering
apply flux

0
Link to comment
Share on other sites
loi xin

loi xin

Posted
Posted

Hqnicolas,

Please help me,
I just bought android TV box X96 X6 (rk3566 8/64G) to use as a server for Home Assistant, but can't install armbian/debian, can you help me? I haven't found a suitable ".img" file to install. Actually I don't know much about armbian.
Thank you very much!

0
Link to comment
Share on other sites
Hqnicolas

Hqnicolas

Posted
  • Author
Posted
On 7/10/2024 at 1:55 AM, loi xin said:

I just bought android TV box X96 X6 (rk3566 8/64G) to use as a server for Home Assistant, but can't install armbian/debian, can you help me? I haven't found a suitable ".img" file to install. Actually I don't know much about armbian.


hello @loi xin

unfortunately the laws in my country have changed for international shopping, we are now living in the North Korea format.
I no longer have access to international products like last year,
I believe you can perform all the methods that were exemplified in this topic
Just create another topic to find people that have the same board as you
Name it "Efforts to develop firmware for X96 X6 k3566 8/64G"

1
Link to comment
Share on other sites
Vincenzoernst1

Vincenzoernst1

Posted
Posted (edited)

oh. sorry didnt notice that it was a X6 version he was asking for.

 

@loi xin

this thing is 135€ in germany and imho not worth it. the v56 is much cheaper with the same functionallity (but "only" having single WIFI). so imho if u have the chance to send it back, replace it with the v56 unit if u can. then u have a ready to go unit.

 

@Hqnicolas opened a topic for the H96 MAX M9 RK3576 TV Box 8G/128G which i find the much more interesting unit, with much more power. but the pricing of this unit (top notch) is holding me back right now.

 

Edited by Vincenzoernst1
1
Link to comment
Share on other sites
pessimism

pessimism

Posted
Posted
[mention=211404]pessimism[/mention]

have u something else connected to get the sdcard reader running? i only get "cant read partiontion table" errors.

No, just soldered the socket. There are seven unpopulated passive components behind it but it didn’t matter for me…


Sent from my iPad using Tapatalk
0
Link to comment
Share on other sites
Vincenzoernst1

Vincenzoernst1

Posted
Posted

@pessimism  hmm....i got i beautuifull soldert on there but sill get the error. maybe there is a modul missing?

 

  

[   60.390814] mmc0: error -110 whilst initialising SD card
[   60.422082] mmc_host mmc0: Bus speed (slot 0) = 375000Hz (slot req 375000Hz, actual 375000HZ div = 0)
[   60.487693] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[   60.487855] mmc0: new high speed SDHC card at address b368
[   60.491174] mmcblk0: mmc0:b368 USD00 29.5 GiB
[   60.530849] mmc_host mmc0: Bus speed (slot 0) = 375000Hz (slot req 375000Hz, actual 375000HZ div = 0)
[   60.580493] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[   60.581278] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[   60.581666] I/O error, dev mmcblk0, sector 1 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[   60.582044] I/O error, dev mmcblk0, sector 2 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[   60.582424] I/O error, dev mmcblk0, sector 3 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[   60.582816] I/O error, dev mmcblk0, sector 4 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[   60.583207] I/O error, dev mmcblk0, sector 5 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[   60.583591] I/O error, dev mmcblk0, sector 6 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[   60.583970] I/O error, dev mmcblk0, sector 7 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[   60.584019] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[   60.586020] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[   60.586412] I/O error, dev mmcblk0, sector 1 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[   60.588580] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[   60.588714]  mmcblk0: unable to read partition table
[   60.615997] Buffer I/O error on dev mmcblk0, logical block 7743984, async page read
[   72.535157] blk_print_req_error: 22 callbacks suppressed
[   72.535169] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
[   72.535403] I/O error, dev mmcblk0, sector 1 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
[   72.535634] I/O error, dev mmcblk0, sector 2 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
[   72.535865] I/O error, dev mmcblk0, sector 3 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
[   72.536096] I/O error, dev mmcblk0, sector 4 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
[   72.536328] I/O error, dev mmcblk0, sector 5 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
[   72.536559] I/O error, dev mmcblk0, sector 6 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
[   72.536791] I/O error, dev mmcblk0, sector 7 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
[   72.537900] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[   72.538133] I/O error, dev mmcblk0, sector 1 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[   72.539579] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[   72.542910] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[   72.547094] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[   72.665033] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[   72.665085]  mmcblk0: unable to read partition table
[   72.680752] Buffer I/O error on dev mmcblk0, logical block 7743984, async page read

 

SD is esxt4 formated. fat also didnt work.

 

any thoughts?

 

 

 

 

0
Link to comment
Share on other sites
Hqnicolas

Hqnicolas

Posted
  • Author
Posted (edited)
2 hours ago, Vincenzoernst1 said:

hmm....i got i beautuifull soldert on there but sill get the error. maybe there is a modul missing?

 

I/O error = missing pad or bad connection


it's plug and play,
the only thing that you need is the socket.
when I do it I discard 4 units before it works....
be carefull with board cooper pads when change sockets


 

  

2 hours ago, Vincenzoernst1 said:

SD is esxt4 formated. fat also didnt work.




Just flash the armbian image with balena etcher......

you dont need to format the sdcard after flash armbian image....

Edited by Hqnicolas
0
Link to comment
Share on other sites
Vincenzoernst1

Vincenzoernst1

Posted
Posted

i alread have armian running. just want to ad the reader for fun.

 

Zitat

I/O error = missing pad or bad connection

 

hmmm....the soldering was very good, so i guess its maybe the cheap chinese sdcard socket. i have still 9 left to try 😡  now i go with the hot gun....

0
Link to comment
Share on other sites
Hqnicolas

Hqnicolas

Posted
  • Author
Posted (edited)
On 7/22/2024 at 11:55 AM, paradigman said:

8/64 don't boot after flash.


will test it here,
edit: downloaded and Tested with 7zip, it boot's on 8/64gb clear android ROM
 make sure you Unzip it With 7zip

 

 

On 7/22/2024 at 11:55 AM, paradigman said:

but to the 4/32 don't able because too big the image for that eMMC

 

the system Uses 24gb (android emulator) + (kodi Games) +(debian Linux)+(wine Desktop)

Next Week I will rebuild it for 4/32gb

Edited by Hqnicolas
0
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
 Share
Go to topic listing
×
×
  • Create New...

Important Information

Terms of Use - Privacy Policy - Guidelines

  I accept