AZ8

Thanks Unfortunately, when I am trying to switch kernel, I got an exception every time cat /tmp/switch_kernel.log linux-image-dev-sunxi64=20.02.12.114 linux-dtb-dev-sunxi64=20.02.12.114 linux-u-boot-orangepi3-dev

Thanks Igor I have found topic with advice to apply patches Had a bit of a success with HDMI audio and also video acceleration on OrangePi 3. What was needed was to apply some patches from LibreELEC, namely ones from projects/Allwinner/patches/linux/ . For video acceleration you need 0005-cedrus-improvements.patch and compile Cedrus driver. When done right you should see in dmesg: cedrus 1c0e000.video-codec: Device registered as /dev/video0 Do you know if this patches already included into Armbian? With latest available armbian for orange pi 3 hw acceleration is not available, so I am trying to build kernel and kodi for Armbian with full mmedia support

Hi guys, I am going to apply some LibeELEC multimedia patches to Armbian kernel Please advise, what is the proper way for this? I have found folder build/userpatches/kernel/sunxi-current. Should I put files here?

I have another issue. I can setup WiFi using nmtui. But it requires connect using ethernet or TTL. If I just set wpa_supplicant.conf, WiFi not works. Do we have any tutorial for Armbian how to setup wifi by editing config on sd card?

Hi guys! Is it possible to include this patch into Armbian tree? patch: https://lists.freedesktop.org/archives/pulseaudio-discuss/2019-June/031168.html explanation: https://habr.com/ru/post/456476/

I have 2 questions: 1. how far Armbian on Opi3 from stable point? 2. did someone compare performance Kodi on Armbian over LibreELEC? Is LibreELEC significantly faster?

Because I dont want to erase mmc If this is not possible, I will backup partition with dd, install using nand-sata-install and restore partition from backup

Wrote latest image to SD Boot from SD mounted /dev/mmcblk2p1, copied armbianEnv.txt formated /dev/mmcblk2p1 rsync /boot to /dev/mmcblk2p1 copy armbianEnv.txt to /dev/mmcblk2p1 removed sd and reboot system starts to boot, but can not find root Is this a proper way to install boot? I do not want to tun nand-sata-install and erase mmc.

Is it possible to boot from sd and recover /boot on mmc?

Maybe I am wrong, but uBoot has version with timestamp like 201904, therefore I assume it was not change during last upgrade.

=> boot switch to partitions #0, OK mmc1(part 0) is current device Scanning mmc 1:1... Found U-Boot script /boot/boot.scr 3042 bytes read in 1 ms (2.9 MiB/s) ## Executing script at 4fc00000 U-boot loaded from SD Boot script loaded from mmc 165 bytes read in 1 ms (161.1 KiB/s) Card did not respond to voltage select! libfdt fdt_check_header(): FDT_ERR_BADMAGIC No FDT memory address configured. Please configure the FDT address via "fdt addr <address>" command. Aborting! Bad Linux ARM64 Image magic! SCRIPT FAILED: continuing... Card did not respond to voltage select! starting USB... No controllers found USB is stopped. Please issue 'usb start' first. starting USB... No controllers found No ethernet found. missing environment variable: pxeuuid missing environment variable: bootfile Retrieving file: pxelinux.cfg/00000000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/0000000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/000000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/00000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/0000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/00 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/0 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/default-arm-sunxi No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/default-arm No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/default No ethernet found. Config file not found starting USB... No controllers found No ethernet found. No ethernet found.

No boot after today upgrade and reboot U-boot wroks fine. Is it possible to recover system without reflash?

Great, thanks. And last question^ when are you going to switch to 5.3? HW watchdog is must have thing for such unstable system like OPi3

Yeah, it is possible to build Armbian_5.93_Orangepi3_Debian_buster_dev_5.2.5.img I have a qustion: do you have a tutorial to set up apt server to update kernel/dtb instead of reflashing?

I have built an image for OPi3. Is it possible to upgrade just kernel without re-flashing whole system?

As per http://linux-sunxi.org/Linux_mainlining_effort Watchdog support for H6 merged into 5.3 Is it possible to use hw watchdog now? Maybe, compile some kernel module?

After updating to new firmware the board not booting and wait on u-boot state => version U-Boot 2019.04-armbian (May 08 2019 - 10:38:01 +0200) Allwinner Technology aarch64-linux-gnu-gcc (Linaro GCC 7.4-2019.02) 7.4.1 20181213 [linaro-7.4-2019.02 revision 56ec6f6b99cc167ff0c2f8e1a2eed33b1edc85d4] GNU ld (Linaro_Binutils-2019.02) 2.28.2.20170706 Please advice, is it possible to upload new image somehow? I mean, without flashing sd card, just in u-boot console

Please advice, how to restore old dtb files? After upgrade to 5.1.7 (debian), OPi3 system became unstable and hang in maximum 50 minutes (sometimes immediately after reboot) Tried to rollback dpkg: warning: downgrading linux-dtb-dev-sunxi64 from 5.89.190614 to 5.89.190612 but still same issue.

apt upgrade returned following Setting up linux-image-dev-sunxi64 (5.88.190529) ... Error! Your kernel headers for kernel 5.1.5-sunxi64 cannot be found. Please install the linux-headers-5.1.5-sunxi64 package, or use the --kernelsourcedir option to tell DKMS where it's located Unfortunately, there is no linux-headers-5.1.5-sunxi64 package

I have a local OpenVPN server on Banan Pi M1, with latest armbian. I tried to replace with OrangePi3 but current results is disappointing iperf3 results on Banana Pi M1 OpenVPN server Connecting to host bouygues.iperf.fr, port 5201 [ 4] local 10.8.0.4 port 46250 connected to 89.84.1.222 port 5201 [ ID] Interval Transfer Bandwidth [ 4] 0.00-1.00 sec 1.69 MBytes 14.1 Mbits/sec [ 4] 1.00-2.00 sec 1.81 MBytes 15.1 Mbits/sec [ 4] 2.00-3.00 sec 2.43 MBytes 20.4 Mbits/sec [ 4] 3.00-4.00 sec 681 KBytes 5.58 Mbits/sec [ 4] 4.00-5.00 sec 1.99 MBytes 16.7 Mbits/sec [ 4] 5.00-6.00 sec 1.33 MBytes 11.2 Mbits/sec [ 4] 6.00-7.00 sec 1.55 MBytes 13.0 Mbits/sec [ 4] 7.00-8.00 sec 1.62 MBytes 13.6 Mbits/sec [ 4] 8.00-9.00 sec 1.33 MBytes 11.2 Mbits/sec [ 4] 9.00-10.00 sec 1.76 MBytes 14.8 Mbits/sec - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bandwidth [ 4] 0.00-10.00 sec 16.2 MBytes 13.6 Mbits/sec sender [ 4] 0.00-10.00 sec 15.7 MBytes 13.2 Mbits/sec receiver iperf3 results on Orange Pi 3 OpenVPN server Connecting to host bouygues.iperf.fr, port 5201 [ 4] local 10.8.1.4 port 41583 connected to 89.84.1.222 port 5201 [ ID] Interval Transfer Bandwidth [ 4] 0.00-1.00 sec 621 KBytes 5.09 Mbits/sec [ 4] 1.00-2.00 sec 868 KBytes 7.11 Mbits/sec [ 4] 2.00-3.00 sec 1.18 MBytes 9.89 Mbits/sec [ 4] 3.00-4.00 sec 1.16 MBytes 9.75 Mbits/sec [ 4] 4.00-5.00 sec 1.02 MBytes 8.53 Mbits/sec [ 4] 5.00-6.00 sec 966 KBytes 7.92 Mbits/sec [ 4] 6.00-7.00 sec 726 KBytes 5.95 Mbits/sec [ 4] 7.00-8.00 sec 676 KBytes 5.54 Mbits/sec [ 4] 8.00-9.00 sec 2.58 MBytes 21.7 Mbits/sec [ 4] 9.00-10.00 sec 4.78 MBytes 40.1 Mbits/sec - - - - - - - - - - - - - - - - - - - - - - - - - [ ID] Interval Transfer Bandwidth [ 4] 0.00-10.00 sec 14.5 MBytes 12.2 Mbits/sec sender [ 4] 0.00-10.00 sec 14.0 MBytes 11.7 Mbits/sec receiver As you can see, connection via OPi3 is slower, but more than that, it is unstabe and fluctuating from 5-8 MBit/s to 40 MBit/s What can I tune to improve openvpn connectivity?

After installation, /etc/apt/apt.conf.d/50unattended-upgrades is empty. What is the proper origins to automatically install at least security patches?

As I understand from https://github.com/armbian/build/commit/69c231dbc0f6a67adea9c487b52b0482ebac3511 currently WireGuard is disabled. So, should I build image on my box with patch to enable it?

Is it possible to integrate wireguard into armbian for opi3, as for banana pi? Currently, lsmod | grep -i wireguard returns empty

1. How to update opi3 with new builds? apt dist-upgrade? 2. How to turn off red light on op3 board?

Time to time i got following notification on Banana Pi M1. Only after reboot Banana starts working properly. How to tune zram to avoid such kind of issue? No tuning made till now Linux bananapi 4.19.17-sunxi #5.73 SMP Mon Jan 28 21:06:40 CET 2019 armv7l GNU/Linux error: Compressing program wrote following message to stderr when compressing log /var/log/letsencrypt/letsencrypt.log.1: gzip: stdout: No space left on device error: failed to compress log /var/log/letsencrypt/letsencrypt.log.1 error: Compressing program wrote following message to stderr when compressing log /var/log/wtmp.1: gzip: stdout: No space left on device error: failed to compress log /var/log/wtmp.1 error: Compressing program wrote following message to stderr when compressing log /var/log/btmp.1: gzip: stdout: No space left on device error: failed to compress log /var/log/btmp.1