Jump to content

wolf7250

Members
 View Profile  See their activity

  • Posts

    17

  • Joined

  • Last visited

 Content Type 

Posts posted by wolf7250

    OdroidHC4 will not start

    in Odroid N2/N2+/HC4

    Posted

    First off, could someone please help. I did not seem to be able to create this topic without a tag and the only tag it would accept was "solved". Wondering if somebody could remove the "solved" tag and add in "odroidhc4"?

     

    I purchased a brand new odroid hc4 board with the intention of installing armbian and then subsequently OMV. My intention was/is to install Armbian on a MicroSD card.

    On the downloader page I read that in order to clean boot Armbian the incompatible Petit bootloader needs to be removed.

     

    I tried the bootloader bypass (preferred) method and that didn't seem to work for me. The board still seemed to go to the petitboot UI.

    I then tried the Petitboot Console method and ran the following commands as detailed on the download page:
      

    # flash_eraseall /dev/mtd0
# flash_eraseall /dev/mtd1
# flash_eraseall /dev/mtd2
# flash_eraseall /dev/mtd3

    These all seemed to run/complete without issue. I then rebooted the board and now absolutely nothing happens. It doesn't boot to the Petitboot UI/Console and it doesn't boot to Armbian either.... Does anybody have any suggestions or wisdom that can help resolve this?

    Thanks 🙂

    0

    ROCKPro64 as NAS?

    in Pine RockPro64

    Posted

    9 minutes ago, soerenderfor said:

    Just so you know, if you plan to use that NAS case from pine. In that case there is only room for 2x 3.5" and 2x 2.5"

    Yep, thanks. I knew that. It was more a question for down the track if I decided to use an old PC case or something to allow me to have more HDDs.

     

    11 minutes ago, soerenderfor said:

    Use 12V always to ROCKPRO64, and around (8A on the safe side) or so to power it all.

    So the DC out for the SATA drives on the board can power 4x3.5" drives if needed if it has a 12V 8A PSU? You would just need a 4 way splitter to go from the one DC output to the 4 drives correct?

    0

    ROCKPro64 as NAS?

    in Pine RockPro64

    Posted

    11 hours ago, soerenderfor said:

    Hope it was a little help, just ask again if there is something i can help with

    You have been an enormous help! Thank you.

    I'll ask one more question if that's OK?

     

    I notice that you mentioned you have 4 HDDs in the case, and the PCI-e Adapter you helped me with has 4 SATA connections. The power supply on the Pine64 store is 12V 5A. I'm pretty sure this is not powerful enough to power both the RockPro64 and 4 x 3.5" HDDs as the power supply for my Helios4 is 12V 8A. How are you powering your 4 HDDs and the board? How do I know how much and what sort of power supply I would need?

     

    Thanks again :)

    0

    ROCKPro64 as NAS?

    in Pine RockPro64

    Posted

    On 8/7/2020 at 4:53 PM, soerenderfor said:

    With new kernels the fan spins at "255" always

    Ahh I didn't initially understand what you meant when you said this. But doing some research "255" refers to the PWM settings, correct? So with the new kernel if the fan spins always at "255" that means it always spins at it's maximum RPM correct?

     

    On 8/8/2020 at 7:30 AM, soerenderfor said:

    I did cut a bigger hole in the orginal pine nas case, and fitted a 92mm Noctua fan

    OK. So Noctua fans appear to be very well respected and reviewed, and very high quality. The Pine64 case allows for an 80mm fan (which is also what they sell on their website). Did you feel that this was not big enough? I see that I could buy an 80mm Noctua fan and not need to cut a bigger hole in the NAS case.....

    On 8/8/2020 at 7:30 AM, soerenderfor said:

    Complete silent, runs with the valuve "170" but as i say it is not standard fan

    So did you create a new PWM ramp for which the maximum was 170 (i.e 0 to 170)? Would I be correct in understanding that this would set the maximum fan speed at 66.66% of the maximum RPM?

     

    Finally, from what I've found it seems as though all Noctua fans use a 3/4 pin connector. Whereas the RockPro64 header for the PWM fan is only 2-pin. How did you get around that?

    0

    ROCKPro64 as NAS?

    in Pine RockPro64

    Posted

    Thanks very much for your feedback!

    16 minutes ago, soerenderfor said:

    OMV works fine, but there can be some probs with sata cards. 

    Are there known SATA cards that should be avoided? Are you using the one from the Pine64 store?

    Did you need to make any adjustments to the CPU governor?

    0

    ROCKPro64 as NAS?

    in Pine RockPro64

    Posted · Edited by TRS-80
    change title from "Stability of RockPro64"

    Hi,

     

    I am looking at investing in a RockPro64 NAS setup using the Pine64 Desktop casing and other necessary accessories. I'm hoping to run OpenMediaVault on it and have 2 3.5" HDDs attached. The entire setup would be configured to be a backup of my operational NAS (Helios4) in a different location (i.e. different room of the house).

     

    My reading of the forum and the armbian download section has me a bit confused. The download section indicates that the board is supported, but the forum indicates it's a WIP.

    Just trying to understand the status/stability of the board for what I'm planning on using it for and whether it would be a good investment or a waste of money.

     

    Also wondering whether this post regarding updating the CPU governor is related -  and will be a benefit - to the RockPro64 as both the NanoPi M4 and RockPro64 share the same SoC RK3399.

     

    Thanks :)

    0

    Anyone managed to successfully install OMV5 on Helios4?

    in Marvell mvebu

    Posted

    Just wanting to do a fresh install of Armbian Buster to install OMV5 via the armbian-config tool.

    I notice that it has been mentioned that Armbian 20.05 is going to be released soon. In fact I can see here that it has been:

    https://www.armbian.com/helios4/#faq-section

    However, when I go to the Helios4 website and follow the documentation as to where to download the latest image from it tells me only 20.02 is available:
    https://wiki.kobol.io/download/
     

    I'm just a little bit confused and was wondering if someone could tell me if the 20.05 image is good to use? Or whether I should wait until it is put on the Helios4 kobol website?

     

    Thanks :)

    0

    Setting up Email Server on Armbian

    in Beginners

    Posted

    Hi all,

     

    I am wanting to setup a mail server on my Helios4. I went through the armbian-config approach and saw that there is an item under softy called ISPConfig which relates to mail servers etc.

    Are there any instructions/documentation around setting up a mail server in this manner?

    Or is there a better option?

     

    Thanks in advance :)

    0
×
×
  • Create New...

Important Information

Terms of Use - Privacy Policy - Guidelines

  I accept