tom_i

Members
  • Content count

    42
  • Joined

  • Last visited

About tom_i

  • Rank
    Advanced Member

Recent Profile Visitors

290 profile views
  1. I've seen that 4.17.X kernel has more features for EspressoBin so I wanted to switch to the NEXT. Ddebian Stretch has 4.4. right?
  2. Same for me man. My ip addr show: nashome@espressobin:/etc/systemd/network$ ip addr show 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: bond0: <BROADCAST,MULTICAST,MASTER> mtu 1500 qdisc noop state DOWN group default qlen 1000 link/ether XX:XX:XX:XX:XX:XX brd ff:ff:ff:ff:ff:ff 3: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN group default qlen 1000 link/ether XX:XX:XX:XX:XX:XX brd ff:ff:ff:ff:ff:ff 4: eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 532 link/ether XX:XX:XX:XX:XX:XX brd ff:ff:ff:ff:ff:ff 5: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 532 link/ether XX:XX:XX:XX:XX:XX brd ff:ff:ff:ff:ff:ff 6: br0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN group default qlen 1000 link/ether XX:XX:XX:XX:XX:XX brd ff:ff So no lan0, lan1 are up, so maybe that's the reason it doesn't work.
  3. Hi @ebin-dev I'm on Debian too: Linux version 4.17.5-mvebu64 (root@nightly) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #87 SMP PREEMPT Sun Jul 8 19:16:19 UTC 2018 lsb_release -a No LSB modules are available. Distributor ID: Debian Description: Debian GNU/Linux testing (buster) Release: testing Codename: buster It shows me some messages about eth0: [ 2868.894331] mvneta d0030000.ethernet eth0: could not attach PHY: -19 [ 2868.898077] mvneta d0030000.ethernet eth0: cannot probe MDIO bus Is there any way, how to debug this? I've tried to define eth0 with DHCP in "/etc/network/interfaces", or run "sudo dhclient eth0". Both with no luck
  4. Ok thx, fortunatelly my board works pretty well Anyway, my network manager doesn't work as I switched from 4.4. kernel to the next 4.17.5. It shows me just: sudo journalctl -u systemd-networkd-wait-online.service - [sudo] password for nashome: -- Logs begin at Sat 2018-07-21 09:50:37 UTC, end at Sat 2018-07-21 09:57:12 UTC Jul 21 09:50:40 espressobin systemd[1]: Starting Wait for Network to be Configur Jul 21 09:52:40 espressobin systemd-networkd-wait-online[566]: Event loop failed Jul 21 09:52:40 espressobin systemd[1]: systemd-networkd-wait-online.service: Ma Jul 21 09:52:40 espressobin systemd[1]: systemd-networkd-wait-online.service: Fa Jul 21 09:52:40 espressobin systemd[1]: Failed to start Wait for Network to be C Because I'm connected it through "screen" so it looks that it break lines of that log :-/
  5. Hi, still no support for booting from SATA?
  6. Fine for me, I thought, that it's some of the weirdness after update Thx @Igor
  7. $ sudo apt-get install armbian-config [sudo] password for XXX: Reading package lists... Done Building dependency tree Reading state information... Done Package armbian-config is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source E: Package 'armbian-config' has no installation candidate Hmm... no way :-/ Looks like, mine Armbian is deeper and deeper in huge mess :-/
  8. Wierd: $ sudo armbian-config sudo: armbian-config: command not found How is it possible? Just firmware update and ```sudo apt update && sudo apt upgrade``` commands were running there.
  9. Mine looks shorter :-O
  10. http://ix.io/1avl
  11. Nn, I'm using ssh over `tilda` linux terminal manager, but if I've tried `konsole`, result is same. I see whole menu there, so no gaps or hidden menu for me :-/ Maybe just one solution should be to install completely new image on my SSD :-/
  12. You meant 'spacebar' key? It doesn't help, it normal enter to ther `Stable` menu. Maybe I have it somehow "broken" or so.. :-/
  13. Strange, I don't have it. Or `armbian-config` has been updated today for me, but there is no change for me. Or maybe I need to reboot it, because, it should be only reason, why I not see that `next` kernel in `armbian-config` - `Systtem` menu
  14. @Igor so you suggest to reinstall whole system if I want dev kernel? Or can I change repo list manually? And I'm not sure that I froze that kernel upgrades. Armbian-config provides me option to freeze it, so I think that it's turned off, or is it some way how to check it different way?
  15. Do you have same problem like mine? https://github.com/armbian/config/issues/21