Jump to content

Search the Community

Showing results for tags 'visionfive2'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


  • Armbian
    • Armbian project administration
  • Community
    • Announcements
    • SBC News
    • Framework and userspace feature requests
    • Off-topic
  • Using Armbian
    • Beginners
    • Software, Applications, Userspace
    • Advanced users - Development
  • Standard support
    • Amlogic meson
    • Allwinner sunxi
    • Rockchip
    • Other families
  • Community maintained / Staging
    • TV boxes
    • Amlogic meson
    • Allwinner sunxi
    • Marvell mvebu
    • Rockchip
    • Other families
  • Support

Find results in...

Find results that contain...

Date Created

  • Start


Last Updated

  • Start


Filter by number of...


  • Start






Website URL







Found 7 results

  1. I wanted to ask you why the RISC-V images are missing and in particular in one case the previous ones are also missing, e.g. https://imola.armbian.com/archive/mangopi-mq/archive
  2. Images for Visionfive-2. https://disk.yandex.ru/d/YDBZD53WnCk1Ig Important. For the system to work correctly, you need to update the bootloader in SPI\flash once (the switch for selecting the device to run should be set to “qspi” 0,0 , this is the default state when delivered from the factory). To do this, download the image from the link https://disk.yandex.ru/d/zsqznfa1ySI2gw burn it to the SD card, connect it to VF2 and turn on the power, wait 2 minutes and turn off the power. After that, you can write an ArmbianTV image to the SD card, connect it to VF2 and the system will start automatically. The next steps are usually the initial setup of Armbian. In versions with DE (IceWM XFCE). even video playback in the window works (fullscreen mode does not work) through the Parole player. Analog audio output is enabled by default, to switch to HDMI audio, use the settings via Volume Control as usual.
  3. The RNNoise code and instructions for compiling it are located at https://gitlab.xiph.org/xiph/rnnoise and highlight the latest addition of Jean-Marc Valin, a developer who I can never thank enough for the work he has done. Two years have passed since the highlighted addition and therefore updated instructions on how to complete the compilation would be useful in general and not just for the hardware we have. This is the sequence of commands: sudo atp update sudo apt install autogen sudo apt install configure-debian sudo apt install dh-autoreconf ./autogen.sh ./configure make -j36 sudo make install -j36 You will now have the RNNoise libraries installed on your system and the demo program to try them in the examples folder. RNNoise is an audio noise suppression library based on a recurrent neural network and it cannot be missing on the hardware used to record the human voice. Those who don’t know it yet can find the documentation on Archiv website and further information on the Mozilla and Jean-Marc Valin's website. I’m sure someone will appreciate it.
  4. Hi, I'm testing a visionfive2 board with 8GB ram and I can only see 4GB in the armbian installed system. As far as I understand, the official image by StarFive has a extra u-boot partition on SD that tricks something to make the ram fully visible to the system. In fact I can see 8GB when using the official debian image but only 4 under armbian. Is there any way to fix this? I'd like to use the armbian environment while using the full ram available. I'm trying to mashup the two partition schemas but I'm probably doing someting wrong... Thank you in advance for any (very appreciated) help! -psi
  5. On Armbian_23.5.0-trunk.140_Visionfive2_lunar_edge_5.15.0.img.xz chrony fails to start: May 02 23:24:48 visionfive2 systemd[1]: Starting chrony.service - chrony, an NTP client/server... May 02 23:24:48 visionfive2 chronyd[1874]: chronyd version 4.3 starting (+CMDMON +NTP +REFCLOCK +RTC +PRIVDROP +SCFILTER +SIGN> May 02 23:24:48 visionfive2 chronyd[1874]: Using right/UTC timezone to obtain leap second data May 02 23:24:48 visionfive2 chronyd[1874]: Fatal error : Failed to load seccomp rules May 02 23:24:48 visionfive2 chronyd-starter.sh[1872]: Failed to load seccomp rules May 02 23:24:48 visionfive2 systemd[1]: chrony.service: Control process exited, code=exited, status=1/FAILURE May 02 23:24:48 visionfive2 systemd[1]: chrony.service: Failed with result 'exit-code'. May 02 23:24:48 visionfive2 systemd[1]: Failed to start chrony.service - chrony, an NTP client/server. So I am using ntpdate (from ntpsec-ntpdate) at boot.
  6. I tried setting SKIP_BOOTSPLASH=yes from Hidden options for advanced users of the Build Options page, but the Armbian splash screen still appears. Since I have to ask here, I am obviously not an advanced user. 🙃 How do I eliminate the boot splash screen as I am building/testing images? ./compile.sh \ BOARD=visionfive2 \ BRANCH=edge \ RELEASE=lunar \ BUILD_MINIMAL=no \ BUILD_DESKTOP=no \ KERNEL_CONFIGURE=no \ SKIP_BOOTSPLASH=yes \ CARD_DEVICE="/dev/sdb"
  7. Works with flash boot select, switches 00 Flash won't boot directly from microSD, switches 01 SD
  • Create New...

Important Information

Terms of Use - Privacy Policy - Guidelines