Jump to content

Pine H64 model A - emmc boot stuck - sunxi-mmc 4022000.mmc: data error, sending stop command


kissste

Recommended Posts

U-Boot SPL 2019.01-armbian (Apr 08 2019 - 01:44:37 +0200)
DRAM: 4096 MiB
Trying to boot from MMC1
NOTICE:  BL31: v2.1(debug):8a08e27
NOTICE:  BL31: Built : 00:11:54, Apr  5 2019
NOTICE:  BL31: Detected Allwinner H6 SoC (1728)
NOTICE:  BL31: Found U-Boot DTB at 0xc06ea70, model: Pine H64
INFO:    ARM GICv2 driver initialized
NOTICE:  PMIC: Probing AXP805
NOTICE:  PMIC: AXP805 detected
INFO:    BL31: Platform setup done
INFO:    BL31: Initializing runtime services
WARNING: BL31: cortex_a53: CPU workaround for 819472 was missing!
WARNING: BL31: cortex_a53: CPU workaround for 824069 was missing!
WARNING: BL31: cortex_a53: CPU workaround for 827319 was missing!
INFO:    BL31: cortex_a53: CPU workaround for 855873 was applied
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x4a000000
INFO:    SPSR = 0x3c9


U-Boot 2019.01-armbian (Apr 08 2019 - 01:44:37 +0200) Allwinner Technology

CPU:   Allwinner H6 (SUN50I)
Model: Pine H64
DRAM:  3 GiB
MMC:   SUNXI SD/MMC: 0, SUNXI SD/MMC: 1
Loading Environment from FAT... Unable to use mmc 1:1... In:    serial@5000000
Out:   serial@5000000
Err:   serial@5000000
Net:   No ethernet found.
starting USB...
No controllers found
Hit any key to stop autoboot:  0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found U-Boot script /boot/boot.scr
3042 bytes read in 27 ms (109.4 KiB/s)
## Executing script at 4fc00000
U-boot loaded from SD
Boot script loaded from mmc
165 bytes read in 23 ms (6.8 KiB/s)
26173 bytes read in 91 ms (280.3 KiB/s)
4161 bytes read in 104 ms (39.1 KiB/s)
Applying kernel provided DT fixup script (sun50i-h6-fixup.scr)
## Executing script at 44000000
8711420 bytes read in 911 ms (9.1 MiB/s)
14436360 bytes read in 1492 ms (9.2 MiB/s)
## Loading init Ramdisk from Legacy Image at 4fe00000 ...
   Image Name:   uInitrd
   Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)
   Data Size:    8711356 Bytes = 8.3 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 4fa00000
   Booting using the fdt blob at 0x4fa00000
   Loading Ramdisk to 497b1000, end 49fffcbc ... OK
   reserving fdt memory region: addr=4fa00000 size=6c000
   Loading Device Tree to 0000000049742000, end 00000000497b0fff ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[    0.000000] Linux version 5.0.7-sunxi64 (root@nightly) (gcc version 7.4.1 20181213 [linaro-7.4-2019.02 revision 56ec6f6b99cc167ff0c2f8e1a2eed33b1edc85d4] (Linaro GCC 7.4-2019.02)) #5.78.190413 SMP Sat Apr 13 01:24:27 CEST 2019
[    0.000000] Machine model: Pine H64
[    0.000000] cma: Reserved 128 MiB at 0x00000000f8000000
[    0.000000] NUMA: No NUMA configuration found
[    0.000000] NUMA: Faking a node at [mem 0x0000000040000000-0x00000000ffffffff]
[    0.000000] NUMA: NODE_DATA [mem 0xf79d9840-0xf79dafff]
[    0.000000] Zone ranges:
[    0.000000]   DMA32    [mem 0x0000000040000000-0x00000000ffffffff]
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000040000000-0x00000000ffffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000ffffffff]
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.1 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.1
[    0.000000] random: get_random_bytes called from start_kernel+0xa8/0x3f0 with crng_init=0
[    0.000000] percpu: Embedded 22 pages/cpu @(____ptrval____) s52952 r8192 d28968 u90112
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: ARM erratum 845719
[    0.000000] Speculative Store Bypass Disable mitigation not required
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 774144
[    0.000000] Policy zone: DMA32
[    0.000000] Kernel command line: root=UUID=ebfa02c2-3f5d-4b27-bb44-1efd898b9c6f rootwait rootfstype=ext4 console=ttyS0,115200 console=tty1 panic=10 consoleblank=0 loglevel=7 ubootpart=3ec23de2-01 usb-storage.quirks=0x2537:0x1066:u,0x2537:0x1068:u   cgroup_enable=memory swapaccount=1
[    0.000000] printk: log_buf_len individual max cpu contribution: 4096 bytes
[    0.000000] printk: log_buf_len total cpu_extra contributions: 12288 bytes
[    0.000000] printk: log_buf_len min size: 16384 bytes
[    0.000000] printk: log_buf_len: 32768 bytes
[    0.000000] printk: early log buf free: 13808(84%)
[    0.000000] Memory: 2935272K/3145728K available (10238K kernel code, 722K rwdata, 2504K rodata, 576K init, 288K bss, 79384K reserved, 131072K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000004] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000217] Console: colour dummy device 80x25
[    0.000553] printk: console [tty1] enabled
[    0.000625] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[    0.000646] pid_max: default: 32768 minimum: 301
[    0.000734] LSM: Security Framework initializing
[    0.000751] AppArmor: AppArmor disabled by boot time parameter
[    0.002318] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.003113] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.003170] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.003222] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.004461] ASID allocator initialised with 32768 entries
[    0.004540] rcu: Hierarchical SRCU implementation.
[    0.005051] smp: Bringing up secondary CPUs ...
[    0.005739] Detected VIPT I-cache on CPU1
[    0.005788] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[    0.006370] Detected VIPT I-cache on CPU2
[    0.006398] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[    0.006960] Detected VIPT I-cache on CPU3
[    0.006987] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[    0.007050] smp: Brought up 1 node, 4 CPUs
[    0.007102] SMP: Total of 4 processors activated.
[    0.007113] CPU features: detected: 32-bit EL0 Support
[    0.007124] CPU features: detected: CRC32 instructions
[    0.007371] CPU: All CPU(s) started at EL2
[    0.007393] alternatives: patching kernel code
[    0.008954] devtmpfs: initialized
[    0.013510] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.013560] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.017717] xor: measuring software checksum speed
[    0.056091]    8regs     :  1750.000 MB/sec
[    0.096130]    32regs    :  2151.000 MB/sec
[    0.136174]    arm64_neon:  1907.000 MB/sec
[    0.136185] xor: using function: 32regs (2151.000 MB/sec)
[    0.136249] pinctrl core: initialized pinctrl subsystem
[    0.136976] NET: Registered protocol family 16
[    0.137437] audit: initializing netlink subsys (disabled)
[    0.137584] audit: type=2000 audit(0.136:1): state=initialized audit_enabled=0 res=1
[    0.138029] cpuidle: using governor menu
[    0.138264] vdso: 2 pages (1 code @ (____ptrval____), 1 data @ (____ptrval____))
[    0.138282] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.139376] DMA: preallocated 256 KiB pool for atomic allocations
[    0.139468] Serial: AMBA PL011 UART driver
[    0.149330] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[    0.149356] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[    0.149369] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.149381] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[    0.149822] cryptd: max_cpu_qlen set to 1000
[    0.216341] raid6: neonx8   gen()  1254 MB/s
[    0.284427] raid6: neonx8   xor()  1169 MB/s
[    0.352541] raid6: neonx4   gen()  1157 MB/s
[    0.420582] raid6: neonx4   xor()  1103 MB/s
[    0.488732] raid6: neonx2   gen()   887 MB/s
[    0.556760] raid6: neonx2   xor()   924 MB/s
[    0.624888] raid6: neonx1   gen()   553 MB/s
[    0.692966] raid6: neonx1   xor()   654 MB/s
[    0.761112] raid6: int64x8  gen()   749 MB/s
[    0.829153] raid6: int64x8  xor()   572 MB/s
[    0.897257] raid6: int64x4  gen()   792 MB/s
[    0.965358] raid6: int64x4  xor()   583 MB/s
[    1.033505] raid6: int64x2  gen()   517 MB/s
[    1.101545] raid6: int64x2  xor()   460 MB/s
[    1.169663] raid6: int64x1  gen()   337 MB/s
[    1.237700] raid6: int64x1  xor()   339 MB/s
[    1.237711] raid6: using algorithm neonx8 gen() 1254 MB/s
[    1.237720] raid6: .... xor() 1169 MB/s, rmw enabled
[    1.237730] raid6: using neon recovery algorithm
[    1.238696] SCSI subsystem initialized
[    1.238860] usbcore: registered new interface driver usbfs
[    1.238904] usbcore: registered new interface driver hub
[    1.238971] usbcore: registered new device driver usb
[    1.239201] pps_core: LinuxPPS API ver. 1 registered
[    1.239213] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    1.239240] PTP clock support registered
[    1.240232] clocksource: Switched to clocksource arch_sys_counter
[    1.240365] VFS: Disk quotas dquot_6.6.0
[    1.240427] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.245916] NET: Registered protocol family 2
[    1.246431] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes)
[    1.246548] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[    1.246906] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    1.247417] TCP: Hash tables configured (established 32768 bind 32768)
[    1.247551] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    1.247666] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    1.247900] NET: Registered protocol family 1
[    1.248327] RPC: Registered named UNIX socket transport module.
[    1.248340] RPC: Registered udp transport module.
[    1.248350] RPC: Registered tcp transport module.
[    1.248359] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.248577] Unpacking initramfs...
[    1.685538] Freeing initrd memory: 8504K
[    1.836446] Initialise system trusted keyrings
[    1.836621] workingset: timestamp_bits=44 max_order=20 bucket_order=0
[    1.841274] zbud: loaded
[    1.842544] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.843194] NFS: Registering the id_resolver key type
[    1.843223] Key type id_resolver registered
[    1.843232] Key type id_legacy registered
[    1.843248] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    1.843260] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    1.844039] 9p: Installing v9fs 9p2000 file system support
[    1.973624] NET: Registered protocol family 38
[    1.976426] Key type asymmetric registered
[    1.976448] Asymmetric key parser 'x509' registered
[    1.976512] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    1.976697] io scheduler mq-deadline registered
[    1.976710] io scheduler kyber registered
[    1.976862] io scheduler bfq registered
[    1.977130] sun50i-de2-bus 1000000.display-engine: Error couldn't map SRAM to device
[    1.977707] sun4i-usb-phy 5100400.phy: Couldn't get regulator usb0_vbus... Deferring probe
[    1.978024] sun50i-usb3-phy 5210000.phy: failed to get phy clock
[    1.981505] sun50i-h6-r-pinctrl 7022000.pinctrl: initialized sunXi PIO driver
[    1.988477] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    1.991290] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    1.995246] loop: module loaded
[    1.996215] libphy: Fixed MDIO Bus: probed
[    1.997736] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.997753] ehci-platform: EHCI generic platform driver
[    1.997902] ehci-platform 5101000.usb: EHCI Host Controller
[    1.997942] ehci-platform 5101000.usb: new USB bus registered, assigned bus number 1
[    1.998235] ehci-platform 5101000.usb: irq 18, io mem 0x05101000
[    2.012241] ehci-platform 5101000.usb: USB 2.0 started, EHCI 1.00
[    2.012438] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.00
[    2.012457] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.012472] usb usb1: Product: EHCI Host Controller
[    2.012484] usb usb1: Manufacturer: Linux 5.0.7-sunxi64 ehci_hcd
[    2.012497] usb usb1: SerialNumber: 5101000.usb
[    2.012939] hub 1-0:1.0: USB hub found
[    2.012977] hub 1-0:1.0: 1 port detected
[    2.013478] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.013506] ohci-platform: OHCI generic platform driver
[    2.013640] ohci-platform 5101400.usb: Generic Platform OHCI controller
[    2.013665] ohci-platform 5101400.usb: new USB bus registered, assigned bus number 2
[    2.013900] ohci-platform 5101400.usb: irq 19, io mem 0x05101400
[    2.076546] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.00
[    2.076565] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.076580] usb usb2: Product: Generic Platform OHCI controller
[    2.076593] usb usb2: Manufacturer: Linux 5.0.7-sunxi64 ohci_hcd
[    2.076606] usb usb2: SerialNumber: 5101400.usb
[    2.076990] hub 2-0:1.0: USB hub found
[    2.077034] hub 2-0:1.0: 1 port detected
[    2.077777] usbcore: registered new interface driver usb-storage
[    2.078187] mousedev: PS/2 mouse device common for all mice
[    2.078613] sun6i-rtc 7000000.rtc: registered as rtc0
[    2.078627] sun6i-rtc 7000000.rtc: RTC enabled
[    2.078690] i2c /dev entries driver
[    2.078874] sun50i-h6-r-pinctrl 7022000.pinctrl: 7022000.pinctrl supply vcc-pl not found, using dummy regulator
[    2.078941] sun50i-h6-r-pinctrl 7022000.pinctrl: Linked as a consumer to regulator.0
[    2.079399] axp20x-i2c 0-0036: AXP20x variant AXP806 found
[    2.084709] input: axp20x-pek as /devices/platform/soc/7081400.i2c/i2c-0/0-0036/axp221-pek/input/input0
[    2.085832] dcdca: supplied by regulator-dummy
[    2.086864] dcdcc: supplied by regulator-dummy
[    2.087453] dcdcd: supplied by regulator-dummy
[    2.087925] vdd-sys: Bringing 900000uV into 960000-960000uV
[    2.088386] dcdce: supplied by regulator-dummy
[    2.088965] aldo1: supplied by regulator-dummy
[    2.089542] aldo2: supplied by regulator-dummy
[    2.090013] vcc-ac200: Bringing 700000uV into 3300000-3300000uV
[    2.090457] aldo3: supplied by regulator-dummy
[    2.090907] vcc-3v3-1: Bringing 700000uV into 3300000-3300000uV
[    2.091658] bldo1: supplied by regulator-dummy
[    2.092650] bldo2: supplied by regulator-dummy
[    2.093250] bldo3: supplied by regulator-dummy
[    2.093697] vcc-wifi-io: Bringing 700000uV into 1800000-1800000uV
[    2.094445] bldo4: supplied by regulator-dummy
[    2.095046] cldo1: supplied by regulator-dummy
[    2.095648] cldo2: supplied by regulator-dummy
[    2.096099] vcc-wifi-1: Bringing 700000uV into 3300000-3300000uV
[    2.096864] cldo3: supplied by regulator-dummy
[    2.097315] vcc-wifi-2: Bringing 700000uV into 3300000-3300000uV
[    2.098072] sw: supplied by regulator-dummy
[    2.098237] axp20x-i2c 0-0036: AXP20X driver loaded
[    2.098956] sun50i-h6-r-pinctrl 7022000.pinctrl: 7022000.pinctrl supply vcc-pm not found, using dummy regulator
[    2.099179] sdhci: Secure Digital Host Controller Interface driver
[    2.099190] sdhci: Copyright(c) Pierre Ossman
[    2.099221] Synopsys Designware Multimedia Card Interface Driver
[    2.099715] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.100332] ledtrig-cpu: registered to indicate activity on CPUs
[    2.100612] hidraw: raw HID events driver (C) Jiri Kosina
[    2.100709] usbcore: registered new interface driver usbhid
[    2.100720] usbhid: USB HID core driver
[    2.101896] NET: Registered protocol family 10
[    2.122205] Segment Routing with IPv6
[    2.122311] NET: Registered protocol family 17
[    2.122485] 8021q: 802.1Q VLAN Support v1.8
[    2.122645] 9pnet: Installing 9P2000 support
[    2.122708] Key type dns_resolver registered
[    2.123319] registered taskstats version 1
[    2.123330] Loading compiled-in X.509 certificates
[    2.123414] zswap: loaded using pool lzo/zbud
[    2.124468] Btrfs loaded, crc32c=crc32c-generic
[    2.132812] Key type encrypted registered
[    2.141659] sun4i-usb-phy 5100400.phy: Linked as a consumer to regulator.18
[    2.142065] phy phy-5210000.phy.2: Linked as a consumer to regulator.18
[    2.146273] sun50i-h6-pinctrl 300b000.pinctrl: initialized sunXi PIO driver
[    2.146547] sun50i-h6-pinctrl 300b000.pinctrl: 300b000.pinctrl supply vcc-ph not found, using dummy regulator
[    2.146622] sun50i-h6-pinctrl 300b000.pinctrl: Linked as a consumer to regulator.0
[    2.146978] printk: console [ttyS0] disabled
[    2.167755] 5000000.serial: ttyS0 at MMIO 0x5000000 (irq = 15, base_baud = 1500000) is a 16550A
[    3.523441] printk: console [ttyS0] enabled
[    3.529347] sun4i-drm display-engine: bound 1100000.mixer (ops 0xffff000010b27968)
[    3.537053] sun4i-drm display-engine: bound 6510000.tcon-top (ops 0xffff000010b2bb50)
[    3.545126] sun4i-drm display-engine: bound 6515000.lcd-controller (ops 0xffff000010b24450)
[    3.553550] sun8i-dw-hdmi 6000000.hdmi: 6000000.hdmi supply hvcc not found, using dummy regulator
[    3.562468] sun8i-dw-hdmi 6000000.hdmi: Linked as a consumer to regulator.0
[    3.569623] sun8i-dw-hdmi 6000000.hdmi: Detected HDMI TX controller v2.12a with HDCP (DWC HDMI 2.0 TX PHY)
[    3.579698] sun8i-dw-hdmi 6000000.hdmi: registered DesignWare HDMI I2C bus driver
[    3.587432] sun4i-drm display-engine: bound 6000000.hdmi (ops 0xffff000010b26d20)
[    3.594923] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    3.601539] [drm] No driver support for vblank timestamp query.
[    3.607712] [drm] Initialized sun4i-drm 1.0.0 20150629 for display-engine on minor 0
[    3.615499] [drm] Cannot find any crtc or sizes
[    3.620514] [drm] Cannot find any crtc or sizes
[    3.732493] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
[    3.738005] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3
[    3.746122] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220f064 hci version 0x100 quirks 0x0000000002010010
[    3.755562] xhci-hcd xhci-hcd.2.auto: irq 20, io mem 0x05200000
[    3.761778] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.00
[    3.770052] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.777280] usb usb3: Product: xHCI Host Controller
[    3.782165] usb usb3: Manufacturer: Linux 5.0.7-sunxi64 xhci-hcd
[    3.788176] usb usb3: SerialNumber: xhci-hcd.2.auto
[    3.793456] hub 3-0:1.0: USB hub found
[    3.797243] hub 3-0:1.0: 1 port detected
[    3.801418] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
[    3.806921] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4
[    3.814591] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0  SuperSpeed
[    3.821269] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    3.829481] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.00
[    3.837755] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.844983] usb usb4: Product: xHCI Host Controller
[    3.849868] usb usb4: Manufacturer: Linux 5.0.7-sunxi64 xhci-hcd
[    3.855880] usb usb4: SerialNumber: xhci-hcd.2.auto
[    3.861084] hub 4-0:1.0: USB hub found
[    3.864866] hub 4-0:1.0: 1 port detected
[    3.869483] ehci-platform 5311000.usb: EHCI Host Controller
[    3.875081] ehci-platform 5311000.usb: new USB bus registered, assigned bus number 5
[    3.883152] ehci-platform 5311000.usb: irq 21, io mem 0x05311000
[    3.904247] ehci-platform 5311000.usb: USB 2.0 started, EHCI 1.00
[    3.910494] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.00
[    3.918769] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.925999] usb usb5: Product: EHCI Host Controller
[    3.930884] usb usb5: Manufacturer: Linux 5.0.7-sunxi64 ehci_hcd
[    3.936897] usb usb5: SerialNumber: 5311000.usb
[    3.941785] hub 5-0:1.0: USB hub found
[    3.945569] hub 5-0:1.0: 1 port detected
[    3.950068] ohci-platform 5311400.usb: Generic Platform OHCI controller
[    3.956707] ohci-platform 5311400.usb: new USB bus registered, assigned bus number 6
[    3.964662] ohci-platform 5311400.usb: irq 22, io mem 0x05311400
[    4.032502] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.00
[    4.040777] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.048006] usb usb6: Product: Generic Platform OHCI controller
[    4.053933] usb usb6: Manufacturer: Linux 5.0.7-sunxi64 ohci_hcd
[    4.059944] usb usb6: SerialNumber: 5311400.usb
[    4.064842] hub 6-0:1.0: USB hub found
[    4.068691] hub 6-0:1.0: 1 port detected
[    4.073372] usb_phy_generic usb_phy_generic.3.auto: usb_phy_generic.3.auto supply vcc not found, using dummy regulator
[    4.084148] usb_phy_generic usb_phy_generic.3.auto: Linked as a consumer to regulator.0
[    4.092422] musb-hdrc musb-hdrc.4.auto: MUSB HDRC host driver
[    4.098181] musb-hdrc musb-hdrc.4.auto: new USB bus registered, assigned bus number 7
[    4.106177] usb usb7: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.00
[    4.114455] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.121685] usb usb7: Product: MUSB HDRC host driver
[    4.126657] usb usb7: Manufacturer: Linux 5.0.7-sunxi64 musb-hcd
[    4.132669] usb usb7: SerialNumber: musb-hdrc.4.auto
[    4.138302] hub 7-0:1.0: USB hub found
[    4.142094] hub 7-0:1.0: 1 port detected
[    4.146906] sun50i-h6-pinctrl 300b000.pinctrl: 300b000.pinctrl supply vcc-pf not found, using dummy regulator
[    4.157036] sunxi-mmc 4020000.mmc: Linked as a consumer to regulator.14
[    4.164240] sunxi-mmc 4020000.mmc: Got CD GPIO
[    4.194041] sunxi-mmc 4020000.mmc: initialized, max. request size: 16384 KB, uses new timings mode
[    4.203554] sun50i-h6-pinctrl 300b000.pinctrl: 300b000.pinctrl supply vcc-pg not found, using dummy regulator
[    4.213654] sunxi-mmc 4021000.mmc: Linked as a consumer to regulator.15
[    4.220336] sunxi-mmc 4021000.mmc: Linked as a consumer to regulator.11
[    4.227513] sunxi-mmc 4021000.mmc: allocated mmc-pwrseq
[    4.266788] mmc0: host does not support reading read-only switch, assuming write-enable
[    4.276590] mmc0: Problem switching card into high-speed mode!
[    4.282516] mmc0: new SDHC card at address 0001
[    4.287236] usb 3-1: new high-speed USB device number 2 using xhci-hcd
[    4.294557] mmcblk0: mmc0:0001 SD 29.1 GiB
[    4.298922] usb 5-1: new high-speed USB device number 2 using ehci-platform
[    4.307381]  mmcblk0: p1
[    4.312427] random: fast init done
[    4.460245] sunxi-mmc 4021000.mmc: initialized, max. request size: 16384 KB, uses new timings mode
[    4.469819] sun50i-h6-pinctrl 300b000.pinctrl: 300b000.pinctrl supply vcc-pc not found, using dummy regulator
[    4.479943] sunxi-mmc 4022000.mmc: Linked as a consumer to regulator.14
[    4.486608] sunxi-mmc 4022000.mmc: Linked as a consumer to regulator.11
[    4.500271] usb 3-1: New USB device found, idVendor=148f, idProduct=3070, bcdDevice= 1.01
[    4.508471] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    4.515615] usb 3-1: Product: 802.11 n WLAN
[    4.519810] usb 3-1: Manufacturer: Ralink
[    4.523828] usb 3-1: SerialNumber: 1.0
[    4.540270] sunxi-mmc 4022000.mmc: initialized, max. request size: 2048 KB, uses new timings mode
[    4.549450] sun6i-rtc 7000000.rtc: setting system clock to 1970-01-01T00:00:09 UTC (9)
[    4.557507] of_cfs_init
[    4.560034] of_cfs_init: OK
[    4.563017] vcc3v3: disabling
[    4.565996] vcc1v8: disabling
[    4.568978] vdd-gpu: disabling
[    4.572697] Freeing unused kernel memory: 576K
[    4.588281] Run /init as init process
[    4.664320] mmc2: new DDR MMC card at address 0001
[    4.670421] mmcblk2: mmc2:0001 NCard  14.5 GiB
[    4.675813] mmcblk2boot0: mmc2:0001 NCard  partition 1 4.00 MiB
[    4.682544] mmcblk2boot1: mmc2:0001 NCard  partition 2 4.00 MiB
[    4.689552]  mmcblk2: p1
[    4.720051] sunxi-mmc 4022000.mmc: data error, sending stop command
[    4.726460] sunxi-mmc 4022000.mmc: send stop command failed
[    4.732785] sunxi-mmc 4022000.mmc: data error, sending stop command
[    5.736234] sunxi-mmc 4022000.mmc: send stop command failed

 

Link to comment
Share on other sites

On 8/23/2019 at 8:48 PM, hexdump said:

@kissste - there is a good chance, that this patch will fix your problem too - for me it fixed the emmc problems - see

 

tx6 i can not boot or reboot, this solution to fix it, but i know to do this, pls guide me to patch for eMMC from this comment below
 

On 8/23/2019 at 1:25 AM, jernej said:

@hexdump Can you test this patch for eMMC? https://pastebin.com/XeUbuWGG (kindly provided by Alexis3D from #linux-sunxi).


thx.

Edited by tongexhispeed@gmail.com
edit link
Link to comment
Share on other sites

On 8/23/2019 at 9:48 PM, hexdump said:

@kissste - there is a good chance, that this patch will fix your problem too - for me it fixed the emmc problems - see

 

can you tell me step by step how you use the patch to solve error mmc tx6,,because i have same froblem with you

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...

Important Information

Terms of Use - Privacy Policy - Guidelines