VictoriaOnSnow Posted April 16, 2016 Share Posted April 16, 2016 Hello, using newest Legacy Image Armbian_5.04_Cubietruck_Debian_jessie_3.4.110 there is still a wifi problem while booting. Correct? For more than one minute the boot process hangs showing following error message: "A Start Job is running for LSB: Raise network interfaces" After one minute the boot process continues. The wlan0 connection gets somehow established. But it is slowly und not really stable. root@cubietruck:~$ cat /etc/network/interfaces auto eth0 iface eth0 inet dhcp auto wlan0 iface wlan0 inet dhcp wpa-ssid My-SSID wpa-psk My-Password auto lo iface lo inet loopback root@cubietruck:~$ lsmod Module Size Used by cpufreq_userspace 3524 0 sg 23765 0 ap6210 625672 0 sunxi_ir 4037 0 hidp 17640 0 rfcomm 58686 0 hci_uart 25000 0 bluetooth 264185 5 hidp,hci_uart,rfcomm dmesg: [ 5.651519] systemd[1]: Starting Syslog Socket. [ 5.656508] systemd[1]: Listening on Syslog Socket. [ 5.660963] systemd[1]: Starting Journal Service... [ 5.692171] systemd[1]: Started Journal Service. [ 5.702433] input: sunxi-ir as /devices/virtual/input/input4 [ 5.704280] IR Initial OK [ 5.804250] [ap6210] select wifi ap6210 [ 5.815858] [ap6210] Initializing ap6210. [ 5.822280] [ap6210] platform device registered successfully. [ 5.826606] [ap6210] Using ap6210 configuration. [ 5.944254] [mmc-msg] sdc3 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 5.958970] [mmc-msg] sdc3 power on [ 5.984883] [mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 5.989811] [mmc-msg] sdc3 set round clock 400000, src 24000000 [ 6.070155] [ap6210] WLAN placed in POWER ON [ 6.082203] [mmc-err] smc 3 err, cmd 52, RTO [ 6.086349] [mmc-err] smc 3 err, cmd 52, RTO [ 6.094725] [mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 6.106362] [mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 6.114847] [mmc-err] smc 3 err, cmd 8, RTO [ 6.123881] [mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 6.127901] systemd-udevd[105]: starting version 215 [ 6.147256] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) [ 6.160363] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 6.172289] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 6.179640] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) [ 6.209152] [mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B [ 6.221414] [mmc-msg] sdc3 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B [ 6.226696] [mmc-msg] sdc3 set round clock 42857143, src 600000000 [ 6.290586] [mmc-msg] sdc3 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 6.300506] mmc1: new high speed SDIO card at address 0001 [ 6.304969] [ap6210] Linux Kernel SDIO/MMC Driver [ 6.324122] [ap6210] Broadcom Dongle Host Driver: register interface [wlan0] MAC: 00:90:4c:11:22:33 [ 6.816813] [ap6210] WLAN placed in RESET [ 7.217988] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 7.628632] EXT4-fs (mmcblk0p1): re-mounted. Opts: data=writeback,commit=600,errors=remount-ro [ 8.135661] Adding 131068k swap on /var/swap. Priority:-1 extents:1 across:131068k SS [ 8.219590] [ap6210] Using ap6210 configuration. [ 8.682494] systemd-journald[101]: Received request to flush runtime journal from PID 1 [ 9.186599] sunxi_gmac: probed [ 9.192082] eth0: PHY ID 001cc915 at 0 IRQ 0 (sunxi_gmac-0:00) active [ 9.196875] eth0: PHY ID 001cc915 at 1 IRQ 0 (sunxi_gmac-0:01) [ 11.199742] PHY: sunxi_gmac-0:00 - Link is Up - 100/Full [ 19.799483] eth0: no IPv6 routers present [ 62.638592] usb 5-1: USB disconnect, device number 2 [ 63.895608] ehci_irq: port change detect [ 63.939154] ehci_irq: port change detect [ 64.281851] usb 5-1: new low-speed USB device number 3 using sw-ohci [ 64.514315] input: Logitech USB Optical Mouse as /devices/platform/sw-ohci.2/usb5/5-1/5-1:1.0/input/input5 [ 64.526236] generic-usb 0003:046D:C05A.0004: input,hidraw2: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-sw-ohci-1/input0 [ 70.160329] [ap6210] Dongle Host Driver, version 1.28.23.3 (r). [ 70.167432] [ap6210] Compiled in drivers/net/wireless/ap6210 on Feb 28 2016 at 17:13:38. [ 70.371036] [ap6210] WLAN going back to live [ 70.372797] sdio_reset_comm(): [ 70.381236] [mmc-msg] sdc3 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 70.391740] [mmc-msg] sdc3 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 70.401051] [mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 70.405984] [mmc-msg] sdc3 set round clock 400000, src 24000000 [ 70.469641] [mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 70.483433] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) [ 70.489429] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 70.495419] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 70.502650] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) [ 70.524561] [mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 70.533018] [mmc-msg] sdc3 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 70.538189] [mmc-msg] sdc3 set round clock 42857143, src 600000000 [ 70.601725] [mmc-msg] sdc3 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 70.605556] [ap6210] dhd_bus_devreset: WLAN ON [ 70.611595] [ap6210] Final fw_path=/lib/firmware/ap6210/fw_bcm40181a2.bin [ 70.622316] [ap6210] Final nv_path=/lib/firmware/ap6210/nvram_ap6210.txt [ 70.628912] [ap6210] download firmware /lib/firmware/ap6210/fw_bcm40181a2.bin [ 70.919909] [ap6210] Dongle ready, protocol version 4 [ 70.926526] [ap6210] Dongle ready, protocol version 4 [ 70.938148] [ap6210] Firmware up: op_mode=0x0005, Broadcom Dongle Host Driver mac=98:3b:16:81:07:59 [ 70.956258] [ap6210] Firmware version = wl0: Apr 22 2013 14:50:00 version 5.90.195.89.6 FWID 01-b30a427d [ 70.959244] [ap6210] Chip: a962 Rev 1 Pkg 9 [ 70.965738] [ap6210] p2p0: p2p_dev_addr=9a:3b:16:81:07:59 [ 81.139641] wlan0: no IPv6 routers present [ 86.517656] [ap6210] Couldn't find P2PIE in probe response/beacon [ 86.528817] [ap6210] Couldn't find P2PIE in probe response/beacon [ 86.538836] [ap6210] Couldn't find P2PIE in probe response/beacon [ 86.544727] [ap6210] Couldn't find P2PIE in probe response/beacon [ 86.604441] [ap6210] Couldn't find P2PIE in probe response/beacon [ 92.110103] [ap6210] wl_cfgp2p_do_ioctl: IOCTL req 0x8b03 on p2p0 I/F. Ignoring. [ 92.117048] [ap6210] wl_cfgp2p_do_ioctl: IOCTL req 0x8b1d on p2p0 I/F. Ignoring. [ 92.124434] [ap6210] wl_cfgp2p_do_ioctl: IOCTL req 0x8b09 on p2p0 I/F. Ignoring. [ 93.691415] sunxi_gmac: probed [ 93.696989] eth0: PHY ID 001cc915 at 0 IRQ 0 (sunxi_gmac-0:00) active [ 93.701965] eth0: PHY ID 001cc915 at 1 IRQ 0 (sunxi_gmac-0:01) [ 93.718579] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 94.249248] sunxi_gmac: probed [ 94.254660] eth0: PHY ID 001cc915 at 0 IRQ 0 (sunxi_gmac-0:00) active [ 94.259513] eth0: PHY ID 001cc915 at 1 IRQ 0 (sunxi_gmac-0:01) [ 94.279591] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 96.259989] PHY: sunxi_gmac-0:00 - Link is Up - 100/Full [ 96.267265] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 103.009724] p2p0: no IPv6 routers present [ 106.819706] eth0: no IPv6 routers present [ 159.413080] [ap6210] Couldn't find P2PIE in probe response/beacon [ 159.418491] [ap6210] Couldn't find P2PIE in probe response/beacon [ 159.433247] [ap6210] Couldn't find P2PIE in probe response/beacon [ 159.438638] [ap6210] Couldn't find P2PIE in probe response/beacon [ 159.444145] [ap6210] Couldn't find P2PIE in probe response/beacon [ 159.449463] [ap6210] Couldn't find P2PIE in probe response/beacon [ 159.792900] [ap6210] Couldn't find P2PIE in probe response/beacon [ 159.798485] [ap6210] Couldn't find P2PIE in probe response/beacon [ 159.810808] [ap6210] Couldn't find P2PIE in probe response/beacon [ 159.816694] [ap6210] Couldn't find P2PIE in probe response/beacon [ 161.108750] [ap6210] wl_cfgp2p_do_ioctl: IOCTL req 0x8b03 on p2p0 I/F. Ignoring. [ 161.115986] [ap6210] wl_cfgp2p_do_ioctl: IOCTL req 0x8b1d on p2p0 I/F. Ignoring. [ 161.123417] [ap6210] wl_cfgp2p_do_ioctl: IOCTL req 0x8b09 on p2p0 I/F. Ignoring. [ 162.865714] sunxi_gmac: probed [ 162.871125] eth0: PHY ID 001cc915 at 0 IRQ 0 (sunxi_gmac-0:00) active [ 162.876087] eth0: PHY ID 001cc915 at 1 IRQ 0 (sunxi_gmac-0:01) [ 162.892353] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 164.870859] PHY: sunxi_gmac-0:00 - Link is Up - 100/Full [ 164.878790] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 172.870632] p2p0: no IPv6 routers present Thanks in advance! Link to comment Share on other sites More sharing options...
Igor Posted April 16, 2016 Share Posted April 16, 2016 If you don't have your eth0 connected and it's enabled in config, boot delay is normal. http://linux-sunxi.org/Cubietruck/AP6210 Wifi driver is unchanged but it should somehow work. Try Vanilla / mainline, it's different driver there. Link to comment Share on other sites More sharing options...
Recommended Posts