Никола Ивахнов Posted June 24, 2022 Share Posted June 24, 2022 Hello. I try to install ambian https://www.armbian.com/orange-pi-zero-2/ to orange pi zero 2 and get there on first start: ▒[100]HELLO! BOOT0 is starting May 13 2020 14:10:04! [105]BOOT0 commit : 593cf83 [107]set pll start [110]periph0 has been enabled [113]set pll end [115]unknow PMU [117]PMU: AXP806 [124]vaild para:8 select dram para0 [127]board init ok [129]DRAM BOOT DRIVE INFO: V0.52 [132]the chip id is 0x5000 [135]chip id check OK [137]DRAM_VCC set to 1500 mv [141]read_calibration error [145]read_calibration error [149]read_calibration error [153]read_calibration error [157]read_calibration error [161]read_calibration error [165]read_calibration error [169]read_calibration error [173]read_calibration error [177]read_calibration error [180]retraining final error [184][AUTO DEBUG]32bit,1 ranks training success! [192]DRAM CLK =720 MHZ [194]DRAM Type =3 (3:DDR3,4:DDR4,7:LPDDR3,8:LPDDR4) [200]Actual DRAM SIZE =1024 M [203]DRAM SIZE =1024 MBytes, para1 = 30fa, para2 = 4000000, dram_tpr13 = 6041 [216]DRAM simple test OK. [219]rtc standby flag is 0x0, super standby flag is 0x0 [224]dram size =1024 [226]*****dram handle ok**** [230]card no is 0 [231]sdcard 0 line count 4 [234][mmc]: mmc driver ver 2019-12-19 10:41 [238][mmc]: sdc0 spd mode error, 2 [242][mmc]: set f_max to 50M, set f_max_ddr to 25M [247][mmc]: mmc 0 bias 0 [255][mmc]: Wrong media type 0x0 [258][mmc]: ***Try SD card 0*** [267][mmc]: HSSDR52/SDR25 4 bit [270][mmc]: 50000000 Hz [272][mmc]: 15200 MB [274][mmc]: ***SD/MMC 0 init OK!!!*** [373]Loading boot-pkg Succeed(index=0). [377]Entry_name = u-boot [386]Entry_name = monitor [390]Entry_name = dtbo [393]Entry_name = dtb [397]Jump to second Boot. NOTICE: BL3-1: v1.0(debug):9fecd83 NOTICE: BL3-1: Built : 17:08:29, 2020-05-28 NOTICE: BL3-1 commit: 8 ERROR: Error initializing runtime service tspd_fast NOTICE: BL3-1: Preparing for EL3 exit to normal world NOTICE: BL3-1: Next image address = 0x4a000000 NOTICE: BL3-1: Next image spsr = 0x1d3 U-Boot 2018.05-orangepi (Mar 31 2022 - 11:47:20 +0800) Xunlong Software [00.474]CPU: Allwinner H616 [00.477]Model: Orange Pi Zero 2 I2C: ready [00.482]DRAM: 1 GiB Relocation Offset is: 35ec7000 [00.522]secure enable bit: 0 [00.525]PMU: AXP806 [00.530]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=400Mhz [00.717]sunxi overlay merged okqv [00.720]drv_disp_init [00.748]__clk_enable: clk is null. tv_init()950 fetch tv0 err. [00.753]drv_disp_init finish [00.756]gic: sec monitor mode [00.761]flash init start [00.763]workmode = 0,storage type = 1 [00.767]MMC: 0 [00.768][mmc]: mmc driver ver uboot2018:2021-07-19 14:09:00 [00.774][mmc]: get sdc_type fail and use default host:tm1. [00.785][mmc]: Using default timing para [00.788][mmc]: SUNXI SDMMC Controller Version:0x40200 [00.806][mmc]: card_caps:0x3000000a [00.809][mmc]: host_caps:0x3000003f [00.813]sunxi flash init ok [00.816]Loading Environment from FAT... [00.820][mmc]: mmc driver ver uboot2018:2021-07-19 14:09:00 [00.826][mmc]: get sdc_type fail and use default host:tm1. [00.836][mmc]: Using default timing para [00.840][mmc]: SUNXI SDMMC Controller Version:0x40200 ** Bad device mmc 1 ** Failed (-5) [00.851]usb burn from boot delay time 0 weak:otg_phy_config [00.864]usb prepare ok [01.667]overtime [01.671]do_burn_from_boot usb : no usb exist [01.675]boot_gui_init:start 206 bytes read in 8 ms (24.4 KiB/s) Set HDMI disp_mode to 1080p60 206 bytes read in 8 ms (24.4 KiB/s) Set fb0_width to 1920 Set fb0_height to 1080 [01.976]boot_gui_init:finish [01.978]bmp_name=/boot/boot.bmp 230456 bytes read in 105 ms (2.1 MiB/s) [02.098]update dts Net: [02.101]No ethernet found. Hit any key to stop autoboot: 0 no mmc device at slot 1 [03.128][mmc]: card_caps:0x3000000a [03.131][mmc]: host_caps:0x3000003f switch to partitions #0, OK mmc0 is current device Scanning mmc 0:1... Found U-Boot script /boot/boot.scr 2771 bytes read in 10 ms (270.5 KiB/s) ## Executing script at 43100000 U-boot loaded from SD Boot script loaded from mmc 206 bytes read in 8 ms (24.4 KiB/s) 8484924 bytes read in 3769 ms (2.1 MiB/s) 24129608 bytes read in 4252 ms (5.4 MiB/s) ## Booting kernel from Legacy Image at 41000000 ... Image Name: Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 24129544 Bytes = 23 MiB Load Address: 41000000 Entry Point: 41000000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 43300000 ... Image Name: uInitrd Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 8484860 Bytes = 8.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Ramdisk to 497e8000, end 49fff7fc ... OK reserving fdt memory region: addr=48000000 size=1000000 ## Linux machid: 00000000, FDT addr: 7be86d60 Starting kernel ... ▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒&[100]HELLO! BOOT0 is starting May 13 2020 14:10:04! [105]BOOT0 commit : 593cf83 [107]set pll start [110]periph0 has been enabled [113]set pll end [115]unknow PMU [117]PMU: AXP806 [124]vaild para:8 select dram para0 [127]board init ok [129]DRAM BOOT DRIVE INFO: V0.52 [133]the chip id is 0x5000 [135]chip id check OK [137]DRAM_VCC set to 1500 mv [141]read_calibration error [145]read_calibration error [149]read_calibration error [153]read_calibration error [157]read_calibration error [161]read_calibration error [165]read_calibration error [169]read_calibration error [173]read_calibration error [177]read_calibration error [180]retraining final error [184][AUTO DEBUG]32bit,1 ranks training success! [192]DRAM CLK =720 MHZ [194]DRAM Type =3 (3:DDR3,4:DDR4,7:LPDDR3,8:LPDDR4) [200]Actual DRAM SIZE =1024 M [203]DRAM SIZE =1024 MBytes, para1 = 30fa, para2 = 4000000, dram_tpr13 = 6041 [216]DRAM simple test OK. [219]rtc standby flag is 0x0, super standby flag is 0x0 [224]dram size =1024 [226]*****dram handle ok**** [230]card no is 0 [232]sdcard 0 line count 4 [234][mmc]: mmc driver ver 2019-12-19 10:41 [238][mmc]: sdc0 spd mode error, 2 [242][mmc]: set f_max to 50M, set f_max_ddr to 25M [247][mmc]: mmc 0 bias 0 [255][mmc]: Wrong media type 0x0 [258][mmc]: ***Try SD card 0*** [267][mmc]: HSSDR52/SDR25 4 bit [270][mmc]: 50000000 Hz [272][mmc]: 15200 MB [274][mmc]: ***SD/MMC 0 init OK!!!*** [375]Loading boot-pkg Succeed(index=0). [378]Entry_name = u-boot [387]Entry_name = monitor [391]Entry_name = dtbo [394]Entry_name = dtb [398]Jump to second Boot. NOTICE: BL3-1: v1.0(debug):9fecd83 NOTICE: BL3-1: Built : 17:08:29, 2020-05-28 NOTICE: BL3-1 commit: 8 ERROR: Error initializing runtime service tspd_fast NOTICE: BL3-1: Preparing for EL3 exit to normal world NOTICE: BL3-1: Next image address = 0x4a000000 NOTICE: BL3-1: Next image spsr = 0x1d3 U-Boot 2018.05-orangepi (Mar 31 2022 - 11:47:20 +0800) Xunlong Software [00.475]CPU: Allwinner H616 [00.477]Model: Orange Pi Zero 2 I2C: ready [00.482]DRAM: 1 GiB Relocation Offset is: 35ec7000 [00.523]secure enable bit: 0 [00.525]PMU: AXP806 [00.530]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=400Mhz [00.717]sunxi overlay merged okqv [00.721]drv_disp_init [00.748]__clk_enable: clk is null. tv_init()950 fetch tv0 err. [00.754]drv_disp_init finish [00.756]gic: sec monitor mode [00.762]flash init start [00.764]workmode = 0,storage type = 1 [00.767]MMC: 0 [00.769][mmc]: mmc driver ver uboot2018:2021-07-19 14:09:00 [00.775][mmc]: get sdc_type fail and use default host:tm1. [00.785][mmc]: Using default timing para [00.789][mmc]: SUNXI SDMMC Controller Version:0x40200 [00.807][mmc]: card_caps:0x3000000a [00.810][mmc]: host_caps:0x3000003f [00.813]sunxi flash init ok [00.817]Loading Environment from FAT... [00.820][mmc]: mmc driver ver uboot2018:2021-07-19 14:09:00 [00.826][mmc]: get sdc_type fail and use default host:tm1. [00.837][mmc]: Using default timing para [00.840][mmc]: SUNXI SDMMC Controller Version:0x40200 ** Bad device mmc 1 ** Failed (-5) [00.852]usb burn from boot delay time 0 weak:otg_phy_config [00.865]usb prepare ok [01.668]overtime [01.672]do_burn_from_boot usb : no usb exist [01.676]boot_gui_init:start 206 bytes read in 15 ms (12.7 KiB/s) Set HDMI disp_mode to 1080p60 206 bytes read in 9 ms (21.5 KiB/s) Set fb0_width to 1920 Set fb0_height to 1080 [01.984]boot_gui_init:finish [01.986]bmp_name=/boot/boot.bmp 230456 bytes read in 127 ms (1.7 MiB/s) [02.128]update dts Net: [02.131]No ethernet found. Hit any key to stop autoboot: 0 orangepi# ls -l /dev | grep -E 'sd|hd' syntax error orangep orangepi# fdisk Unknown command 'fdisk' - try 'help' orangepi# help ? - alias for 'help' base - print or set address offset bdinfo - print Board Info structure boot - boot default, i.e., run 'bootcmd' bootd - boot default, i.e., run 'bootcmd' bootm - boot application image from memory bootp - boot image via network using BOOTP/TFTP protocol bootz - boot Linux zImage image from memory cmp - memory compare colorbar- show colorbar coninfo - print console devices and information cp - memory copy crc32 - checksum calculation dhcp - boot image via network using DHCP/TFTP protocol echo - echo args to console editenv - edit environment variable efex - run to efex env - environment handling commands erase - erase FLASH memory exit - exit script ext2load- load binary file from a Ext2 filesystem ext2ls - list files in a directory (default /) ext4load- load binary file from a Ext4 filesystem ext4ls - list files in a directory (default /) ext4size- determine a file's size ext4write- create a file in the root directory false - do nothing, unsuccessfully fastboot- fastboot - enter USB Fastboot protocol fatinfo - print information about filesystem fatload - load binary file from a dos filesystem fatls - list files in a directory (default /) fatsize - determine a file's size fatwrite- write file into a dos filesystem fdt - flattened device tree utility commands flinfo - print FLASH memory information fstype - Look up a filesystem type go - start application at address 'addr' gpt - GUID Partition Table help - print command description/usage i2c - I2C sub-system itest - return true/false on integer compare load - load binary file from a filesystem loadb - load binary file over serial line (kermit mode) loads - load S-Record file over serial line loadx - load binary file over serial line (xmodem mode) loady - load binary file over serial line (ymodem mode) logo - show default logo loop - infinite loop on address range ls - list files in a directory (default /) md - memory display memtester- start application at address 'addr' mii - MII utility commands mm - memory modify (auto-incrementing address) mmc - MMC sub system mmcinfo - display MMC info mw - memory write (fill) nfs - boot image via network using NFS protocol nm - memory modify (constant address) part - disk partition related commands pbread - read data from private data ping - send ICMP ECHO_REQUEST to network host poweroff- Perform POWEROFF of the device printenv- print environment variables protect - enable or disable FLASH write protection pxe - commands to get and boot from pxe files reset - Perform RESET of the CPU run - run commands in an environment variable save - save file to a filesystem saveenv - save environment variables to persistent storage screen_char- show default screen chars setenv - set environment variables setexpr - set environment variable as the result of eval expression showvar - print local hushshell variables size - determine a file's size sleep - delay execution for some time source - run script from memory sprite_test- do a sprite test sunxi_axp- sunxi_axp sub-system sunxi_bmp_info- manipulate BMP image data sunxi_bmp_show- manipulate BMP image data sunxi_card0_probe- probe sunxi card0 device sunxi_flash- sunxi_flash sub-system sunxi_nand_test- sunxi_nand_test sub systerm sysboot - command to get and boot from syslinux files test - minimal test like /bin/sh tftpboot- boot image via network using TFTP protocol timer_test- do a timer and int test timer_test1- do a timer and int test true - do nothing, successfully uburn - do a burn from boot version - print monitor, compiler and linker version orangepi# fsck Unknown command 'fsck' - try 'help' orangepi# ls ls - list files in a directory (default /) Usage: ls <interface> [<dev[:part]> [directory]] - List files in directory 'directory' of partition 'part' on device type 'interface' instance 'dev'. orangepi# cd / Unknown command 'cd' - try 'help' orangepi# ls / ** No device specified ** orangepi# fstab Unknown command 'fstab' - try 'help' orangepi# tune2fs Unknown command 'tune2fs' - try 'help' orangepi# touch /forcefsck Unknown command 'touch' - try 'help' orangepi# help ? - alias for 'help' base - print or set address offset bdinfo - print Board Info structure boot - boot default, i.e., run 'bootcmd' bootd - boot default, i.e., run 'bootcmd' bootm - boot application image from memory bootp - boot image via network using BOOTP/TFTP protocol bootz - boot Linux zImage image from memory cmp - memory compare colorbar- show colorbar coninfo - print console devices and information cp - memory copy crc32 - checksum calculation dhcp - boot image via network using DHCP/TFTP protocol echo - echo args to console editenv - edit environment variable efex - run to efex env - environment handling commands erase - erase FLASH memory exit - exit script ext2load- load binary file from a Ext2 filesystem ext2ls - list files in a directory (default /) ext4load- load binary file from a Ext4 filesystem ext4ls - list files in a directory (default /) ext4size- determine a file's size ext4write- create a file in the root directory false - do nothing, unsuccessfully fastboot- fastboot - enter USB Fastboot protocol fatinfo - print information about filesystem fatload - load binary file from a dos filesystem fatls - list files in a directory (default /) fatsize - determine a file's size fatwrite- write file into a dos filesystem fdt - flattened device tree utility commands flinfo - print FLASH memory information fstype - Look up a filesystem type go - start application at address 'addr' gpt - GUID Partition Table help - print command description/usage i2c - I2C sub-system itest - return true/false on integer compare load - load binary file from a filesystem loadb - load binary file over serial line (kermit mode) loads - load S-Record file over serial line loadx - load binary file over serial line (xmodem mode) loady - load binary file over serial line (ymodem mode) logo - show default logo loop - infinite loop on address range ls - list files in a directory (default /) md - memory display memtester- start application at address 'addr' mii - MII utility commands mm - memory modify (auto-incrementing address) mmc - MMC sub system mmcinfo - display MMC info mw - memory write (fill) nfs - boot image via network using NFS protocol nm - memory modify (constant address) part - disk partition related commands pbread - read data from private data ping - send ICMP ECHO_REQUEST to network host poweroff- Perform POWEROFF of the device printenv- print environment variables protect - enable or disable FLASH write protection pxe - commands to get and boot from pxe files reset - Perform RESET of the CPU run - run commands in an environment variable save - save file to a filesystem saveenv - save environment variables to persistent storage screen_char- show default screen chars setenv - set environment variables setexpr - set environment variable as the result of eval expression showvar - print local hushshell variables size - determine a file's size sleep - delay execution for some time source - run script from memory sprite_test- do a sprite test sunxi_axp- sunxi_axp sub-system sunxi_bmp_info- manipulate BMP image data sunxi_bmp_show- manipulate BMP image data sunxi_card0_probe- probe sunxi card0 device sunxi_flash- sunxi_flash sub-system sunxi_nand_test- sunxi_nand_test sub systerm sysboot - command to get and boot from syslinux files test - minimal test like /bin/sh tftpboot- boot image via network using TFTP protocol timer_test- do a timer and int test timer_test1- do a timer and int test true - do nothing, successfully uburn - do a burn from boot version - print monitor, compiler and linker version orangepi# reboot Unknown command 'reboot' - try 'help' orangepi# ▒▒[100]HELLO! BOOT0 is starting May 13 2020 14:10:04! [105]BOOT0 commit : 593cf83 [107]set pll start [110]periph0 has been enabled [113]set pll end [115]unknow PMU [117]PMU: AXP806 [124]vaild para:8 select dram para0 [127]board init ok [129]DRAM BOOT DRIVE INFO: V0.52 [132]the chip id is 0x5000 [135]chip id check OK [137]DRAM_VCC set to 1500 mv [141]read_calibration error [145]read_calibration error [149]read_calibration error [153]read_calibration error [157]read_calibration error [161]read_calibration error [165]read_calibration error [169]read_calibration error [173]read_calibration error [177]read_calibration error [180]retraining final error [184][AUTO DEBUG]32bit,1 ranks training success! [192]DRAM CLK =720 MHZ [194]DRAM Type =3 (3:DDR3,4:DDR4,7:LPDDR3,8:LPDDR4) [200]Actual DRAM SIZE =1024 M [203]DRAM SIZE =1024 MBytes, para1 = 30fa, para2 = 4000000, dram_tpr13 = 6041 [216]DRAM simple test OK. [219]rtc standby flag is 0x0, super standby flag is 0x0 [224]dram size =1024 [226]*****dram handle ok**** [230]card no is 0 [232]sdcard 0 line count 4 [234][mmc]: mmc driver ver 2019-12-19 10:41 [238][mmc]: sdc0 spd mode error, 2 [242][mmc]: set f_max to 50M, set f_max_ddr to 25M [247][mmc]: mmc 0 bias 0 [255][mmc]: Wrong media type 0x0 [258][mmc]: ***Try SD card 0*** [267][mmc]: HSSDR52/SDR25 4 bit [270][mmc]: 50000000 Hz [272][mmc]: 15200 MB [274][mmc]: ***SD/MMC 0 init OK!!!*** [373]Loading boot-pkg Succeed(index=0). [377]Entry_name = u-boot [386]Entry_name = monitor [390]Entry_name = dtbo [393]Entry_name = dtb [397]Jump to second Boot. NOTICE: BL3-1: v1.0(debug):9fecd83 NOTICE: BL3-1: Built : 17:08:29, 2020-05-28 NOTICE: BL3-1 commit: 8 ERROR: Error initializing runtime service tspd_fast NOTICE: BL3-1: Preparing for EL3 exit to normal world NOTICE: BL3-1: Next image address = 0x4a000000 NOTICE: BL3-1: Next image spsr = 0x1d3 U-Boot 2018.05-orangepi (Mar 31 2022 - 11:47:20 +0800) Xunlong Software [00.474]CPU: Allwinner H616 [00.476]Model: Orange Pi Zero 2 I2C: ready [00.481]DRAM: 1 GiB Relocation Offset is: 35ec7000 [00.522]secure enable bit: 0 [00.524]PMU: AXP806 [00.529]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=400Mhz [00.716]sunxi overlay merged okqv [00.720]drv_disp_init [00.747]__clk_enable: clk is null. tv_init()950 fetch tv0 err. [00.753]drv_disp_init finish [00.755]gic: sec monitor mode [00.761]flash init start [00.763]workmode = 0,storage type = 1 [00.766]MMC: 0 [00.768][mmc]: mmc driver ver uboot2018:2021-07-19 14:09:00 [00.774][mmc]: get sdc_type fail and use default host:tm1. [00.784][mmc]: Using default timing para [00.788][mmc]: SUNXI SDMMC Controller Version:0x40200 [00.806][mmc]: card_caps:0x3000000a [00.809][mmc]: host_caps:0x3000003f [00.812]sunxi flash init ok [00.816]Loading Environment from FAT... [00.819][mmc]: mmc driver ver uboot2018:2021-07-19 14:09:00 [00.825][mmc]: get sdc_type fail and use default host:tm1. [00.836][mmc]: Using default timing para [00.839][mmc]: SUNXI SDMMC Controller Version:0x40200 ** Bad device mmc 1 ** Failed (-5) [00.851]usb burn from boot delay time 0 weak:otg_phy_config [00.864]usb prepare ok [01.667]overtime [01.671]do_burn_from_boot usb : no usb exist [01.675]boot_gui_init:start 206 bytes read in 8 ms (24.4 KiB/s) Set HDMI disp_mode to 1080p60 206 bytes read in 8 ms (24.4 KiB/s) Set fb0_width to 1920 Set fb0_height to 1080 [01.976]boot_gui_init:finish [01.978]bmp_name=/boot/boot.bmp 230456 bytes read in 83 ms (2.6 MiB/s) [02.076]update dts Net: [02.080]No ethernet found. Hit any key to stop autoboot: 0 no mmc device at slot 1 [03.106][mmc]: card_caps:0x3000000a [03.109][mmc]: host_caps:0x3000003f switch to partitions #0, OK mmc0 is current device Scanning mmc 0:1... Found U-Boot script /boot/boot.scr 2771 bytes read in 11 ms (245.1 KiB/s) ## Executing script at 43100000 U-boot loaded from SD Boot script loaded from mmc 206 bytes read in 8 ms (24.4 KiB/s) 8484924 bytes read in 3720 ms (2.2 MiB/s) 24129608 bytes read in 4498 ms (5.1 MiB/s) ## Booting kernel from Legacy Image at 41000000 ... Image Name: Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 24129544 Bytes = 23 MiB Load Address: 41000000 Entry Point: 41000000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 43300000 ... Image Name: uInitrd Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 8484860 Bytes = 8.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Ramdisk to 497e8000, end 49fff7fc ... OK reserving fdt memory region: addr=48000000 size=1000000 ## Linux machid: 00000000, FDT addr: 7be86d60 Starting kernel ... ▒[96]HELLO! BOOT0 is starting May 13 2020 14:10:04! [101]BOOT0 commit : 593cf83 [103]set pll start [106]periph0 has been enabled [109]set pll end [111]unknow PMU [113]PMU: AXP806 [120]vaild para:1 select dram para0 [123]board init ok [125]DRAM BOOT DRIVE INFO: V0.52 [128]the chip id is 0x5000 [131]chip id check OK [133]DRAM_VCC set to 1500 mv [137]read_calibration error [141]read_calibration error [145]read_calibration error [149]read_calibration error [153]read_calibration error [157]read_calibration error [161]read_calibration error [165]read_calibration error [169]read_calibration error [173]read_calibration error [175]retraining final error [180][AUTO DEBUG]32bit,1 ranks training success! [187]DRAM CLK =720 MHZ [190]DRAM Type =3 (3:DDR3,4:DDR4,7:LPDDR3,8:LPDDR4) [196]Actual DRAM SIZE =1024 M [199]DRAM SIZE =1024 MBytes, para1 = 30fa, para2 = 4000000, dram_tpr13 = 6041 [212]DRAM simple test OK. [215]rtc standby flag is 0x0, super standby flag is 0x0 [220]dram size =1024 [222]*****dram handle ok**** [226]card no is 0 [227]sdcard 0 line count 4 [230][mmc]: mmc driver ver 2019-12-19 10:41 [234][mmc]: sdc0 spd mode error, 2 [238][mmc]: set f_max to 50M, set f_max_ddr to 25M [243][mmc]: mmc 0 bias 0 [251][mmc]: Wrong media type 0x0 [254][mmc]: ***Try SD card 0*** [263][mmc]: HSSDR52/SDR25 4 bit [266][mmc]: 50000000 Hz [268][mmc]: 15200 MB [270][mmc]: ***SD/MMC 0 init OK!!!*** [369]Loading boot-pkg Succeed(index=0). [373]Entry_name = u-boot [382]Entry_name = monitor [386]Entry_name = dtbo [389]Entry_name = dtb [393]Jump to second Boot. NOTICE: BL3-1: v1.0(debug):9fecd83 NOTICE: BL3-1: Built : 17:08:29, 2020-05-28 NOTICE: BL3-1 commit: 8 ERROR: Error initializing runtime service tspd_fast NOTICE: BL3-1: Preparing for EL3 exit to normal world NOTICE: BL3-1: Next image address = 0x4a000000 NOTICE: BL3-1: Next image spsr = 0x1d3 U-Boot 2018.05-armbian (Jun 22 2022 - 07:19:38 +0000) Xunlong Software [00.468]CPU: Allwinner H616 [00.471]Model: Orange Pi Zero 2 I2C: ready [00.476]DRAM: 1 GiB Relocation Offset is: 35ec7000 [00.516]secure enable bit: 0 [00.519]PMU: AXP806 [00.524]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=400Mhz [00.706]sunxi overlay merged okqv [00.709]drv_disp_init [00.738]__clk_enable: clk is null. tv_init()950 fetch tv0 err. [00.744]drv_disp_init finish [00.746]gic: sec monitor mode [00.752]flash init start [00.754]workmode = 0,storage type = 1 [00.757]MMC: 0 [00.759][mmc]: mmc driver ver uboot2018:2021-07-19 14:09:00 [00.765][mmc]: get sdc_type fail and use default host:tm1. [00.775][mmc]: Using default timing para [00.779][mmc]: SUNXI SDMMC Controller Version:0x40200 [00.796][mmc]: card_caps:0x3000000a [00.799][mmc]: host_caps:0x3000003f [00.803]sunxi flash init ok [00.806]Loading Environment from FAT... [00.810][mmc]: mmc driver ver uboot2018:2021-07-19 14:09:00 [00.816][mmc]: get sdc_type fail and use default host:tm1. [00.827][mmc]: Using default timing para [00.830][mmc]: SUNXI SDMMC Controller Version:0x40200 ** Bad device mmc 1 ** Failed (-5) [00.841]usb burn from boot delay time 0 weak:otg_phy_config [00.855]usb prepare ok [01.658]overtime [01.662]do_burn_from_boot usb : no usb exist [01.666]boot_gui_init:start 141 bytes read in 9 ms (14.6 KiB/s) Set HDMI disp_mode to 1080p60 141 bytes read in 8 ms (16.6 KiB/s) Set fb0_width to 1280 Set fb0_height to 720 [01.967]boot_gui_init:finish [01.970]bmp_name=/boot/boot.bmp 230454 bytes read in 30 ms (7.3 MiB/s) [02.013]update dts Net: [02.016]No ethernet found. Hit any key to stop autoboot: 0 no mmc device at slot 1 [03.043][mmc]: card_caps:0x3000000a [03.046][mmc]: host_caps:0x3000003f switch to partitions #0, OK mmc0 is current device Scanning mmc 0:1... Found U-Boot script /boot/boot.scr 3202 bytes read in 10 ms (312.5 KiB/s) ## Executing script at 43100000 U-boot loaded from SD Boot script loaded from mmc 141 bytes read in 8 ms (16.6 KiB/s) 262144 bytes read in 35 ms (7.1 MiB/s) ** File not found /boot/dtb/allwinner/overlay/-fixup.scr ** 6995219 bytes read in 595 ms (11.2 MiB/s) ** File not found /boot/Image ** Unknown command 'booti' - try 'help' SCRIPT FAILED: continuing... No ethernet found. missing environment variable: pxeuuid missing environment variable: bootfile Retrieving file: pxelinux.cfg/00000000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/0000000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/000000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/00000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/0000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/00 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/0 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/default-arm-sunxi No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/default-arm No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/default No ethernet found. Config file not found No ethernet found. armbian# ** Bad device mmc 1 ** Unknown command '**' - try 'help' armbian# mmc rescan [63.143][mmc]: card_caps:0x3000000a [63.146][mmc]: host_caps:0x3000003f armbian# fatls mmc 0:0 ** Unrecognized filesystem type ** armbian# fatls mmc 1:0 ** Bad device mmc 1 ** armbian# fatls mmc 1:0 ** Bad device mmc 1 ** armbian# fatls mmc 0:1 ** Unrecognized filesystem type ** armbian# [90]HELLO! BOOT0 is starting May 13 2020 14:10:04! [95]BOOT0 commit : 593cf83 [97]set pll start [100]periph0 has been enabled [103]set pll end [105]unknow PMU [106]PMU: AXP806 [114]vaild para:1 select dram para0 [117]board init ok [119]DRAM BOOT DRIVE INFO: V0.52 [122]the chip id is 0x5000 [125]chip id check OK [127]DRAM_VCC set to 1500 mv [131]read_calibration error [135]read_calibration error [139]read_calibration error [143]read_calibration error [147]read_calibration error [151]read_calibration error [155]read_calibration error [159]read_calibration error [163]read_calibration error [166]read_calibration error [169]retraining final error [174][AUTO DEBUG]32bit,1 ranks training success! [181]DRAM CLK =720 MHZ [183]DRAM Type =3 (3:DDR3,4:DDR4,7:LPDDR3,8:LPDDR4) [190]Actual DRAM SIZE =1024 M [193]DRAM SIZE =1024 MBytes, para1 = 30fa, para2 = 4000000, dram_tpr13 = 6041 [206]DRAM simple test OK. [208]rtc standby flag is 0x0, super standby flag is 0x0 [214]dram size =1024 [216]*****dram handle ok**** [220]card no is 0 [221]sdcard 0 line count 4 [224][mmc]: mmc driver ver 2019-12-19 10:41 [228][mmc]: sdc0 spd mode error, 2 [232][mmc]: set f_max to 50M, set f_max_ddr to 25M [237][mmc]: mmc 0 bias 0 [245][mmc]: Wrong media type 0x0 [248][mmc]: ***Try SD card 0*** [257][mmc]: HSSDR52/SDR25 4 bit [260][mmc]: 50000000 Hz [262][mmc]: 15200 MB [264][mmc]: ***SD/MMC 0 init OK!!!*** [363]Loading boot-pkg Succeed(index=0). [367]Entry_name = u-boot [376]Entry_name = monitor [380]Entry_name = dtbo [383]Entry_name = dtb [386]Jump to second Boot. NOTICE: BL3-1: v1.0(debug):9fecd83 NOTICE: BL3-1: Built : 17:08:29, 2020-05-28 NOTICE: BL3-1 commit: 8 ERROR: Error initializing runtime service tspd_fast NOTICE: BL3-1: Preparing for EL3 exit to normal world NOTICE: BL3-1: Next image address = 0x4a000000 NOTICE: BL3-1: Next image spsr = 0x1d3 U-Boot 2018.05-armbian (Jun 22 2022 - 07:19:38 +0000) Xunlong Software [00.463]CPU: Allwinner H616 [00.466]Model: Orange Pi Zero 2 I2C: ready [00.471]DRAM: 1 GiB Relocation Offset is: 35ec7000 [00.511]secure enable bit: 0 [00.514]PMU: AXP806 [00.519]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=400Mhz [00.701]sunxi overlay merged okqv [00.704]drv_disp_init [00.733]__clk_enable: clk is null. tv_init()950 fetch tv0 err. [00.739]drv_disp_init finish [00.741]gic: sec monitor mode [00.747]flash init start [00.749]workmode = 0,storage type = 1 [00.752]MMC: 0 [00.754][mmc]: mmc driver ver uboot2018:2021-07-19 14:09:00 [00.760][mmc]: get sdc_type fail and use default host:tm1. [00.770][mmc]: Using default timing para [00.774][mmc]: SUNXI SDMMC Controller Version:0x40200 [00.792][mmc]: card_caps:0x3000000a [00.795][mmc]: host_caps:0x3000003f [00.798]sunxi flash init ok [00.802]Loading Environment from FAT... [00.805][mmc]: mmc driver ver uboot2018:2021-07-19 14:09:00 [00.811][mmc]: get sdc_type fail and use default host:tm1. [00.822][mmc]: Using default timing para [00.825][mmc]: SUNXI SDMMC Controller Version:0x40200 ** Bad device mmc 1 ** Failed (-5) [00.837]usb burn from boot delay time 0 weak:otg_phy_config [00.850]usb prepare ok [01.653]overtime [01.657]do_burn_from_boot usb : no usb exist [01.661]boot_gui_init:start 141 bytes read in 9 ms (14.6 KiB/s) Set HDMI disp_mode to 1080p60 141 bytes read in 8 ms (16.6 KiB/s) Set fb0_width to 1280 Set fb0_height to 720 [01.962]boot_gui_init:finish [01.965]bmp_name=/boot/boot.bmp 230454 bytes read in 29 ms (7.6 MiB/s) [02.008]update dts Net: [02.011]No ethernet found. Hit any key to stop autoboot: 0 no mmc device at slot 1 [03.038][mmc]: card_caps:0x3000000a [03.041][mmc]: host_caps:0x3000003f switch to partitions #0, OK mmc0 is current device Scanning mmc 0:1... Found U-Boot script /boot/boot.scr 3202 bytes read in 11 ms (284.2 KiB/s) ## Executing script at 43100000 U-boot loaded from SD Boot script loaded from mmc 141 bytes read in 9 ms (14.6 KiB/s) 262144 bytes read in 35 ms (7.1 MiB/s) ** File not found /boot/dtb/allwinner/overlay/-fixup.scr ** 6995219 bytes read in 594 ms (11.2 MiB/s) ** File not found /boot/Image ** Unknown command 'booti' - try 'help' SCRIPT FAILED: continuing... No ethernet found. missing environment variable: pxeuuid missing environment variable: bootfile Retrieving file: pxelinux.cfg/00000000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/0000000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/000000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/00000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/0000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/00 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/0 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/default-arm-sunxi No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/default-arm No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/default No ethernet found. Config file not found No ethernet found. armbian# File not found /boot/Imageprintenv Unknown command 'File' - try 'help' armbian# printenv arch=arm baudrate=115200 board=sunxi board_name=sunxi boot_a_script=load ${devtype} ${devnum}:${distro_bootpart} ${scriptaddr} ${prefix}${script}; source ${scriptaddr} boot_disp=1034 boot_disp1=0 boot_disp2=0 boot_extlinux=sysboot ${devtype} ${devnum}:${distro_bootpart} any ${scriptaddr} ${prefix}extlinux/extlinux.conf boot_fb0=7bf4fcc0,500,2d0,20,1400,1e0,f0,320,1e0 boot_prefixes=/ /boot/ boot_script_dhcp=boot.scr.uimg boot_scripts=boot.scr.uimg boot.scr boot_targets=fel mmc_auto pxe dhcp bootargs=root=UUID=7af2b6ff-a1ee-4678-af7e-2271601e558c rootwait rootfstype=ext4 console=ttyS0,115200 consoleblank=0 loglevel=1 ubootpart=f9fc421d-01 usb-storage.quirks= cgroup_enable=memory swapaccount=1 bootcmd=run distro_bootcmd bootcmd_dhcp=if dhcp ${scriptaddr} ${boot_script_dhcp}; then source ${scriptaddr}; fi; bootcmd_fel=if test -n ${fel_booted} && test -n ${fel_scriptaddr}; then echo '(FEL boot)'; source ${fel_scriptaddr}; fi bootcmd_mmc0=setenv devnum 0; run mmc_boot bootcmd_mmc1=setenv devnum 1; run mmc_boot bootcmd_mmc_auto=if test ${mmc_bootdev} -eq 1; then run bootcmd_mmc1; run bootcmd_mmc0; elif test ${mmc_bootdev} -eq 0; then run bootcmd_mmc0; run bootcmd_mmc1; fi bootcmd_pxe=dhcp; if pxe get; then pxe boot; fi bootdelay=1 bootfstype=ext4 bootlogo=false bootm_size=0xa000000 bootreason=unknow console=serial consoleargs=console=ttyS0,115200 cpu=armv7 devnum=0 devplist=1 devtype=mmc dfu_alt_info_ram=kernel ram 0x41000000 0x1000000;fdt ram 0x43000000 0x100000;ramdisk ram 0x43300000 0x4000000 disp_mode=1080p60 disp_reserve=3686400,0x7bf4fcc0 distro_bootcmd=for target in ${boot_targets}; do run bootcmd_${target}; done docker_optimizations=on fb0_height=720 fb0_width=1280 fdt_addr_r=0x43000000 fdtaddr=43000000 fdtcontroladdr=7be87560 fdtfile=sunxi/sun50i-h616-orangepi-zero2.dtb fileaddr=43300000 filesize=6abd13 kernel_addr_r=0x41000000 load_addr=0x45000000 mmc_boot=if mmc dev ${devnum}; then setenv devtype mmc; run scan_dev_for_boot_part; fi overlay_error=false partitions=name=loader1,start=8k,size=32k,uuid=${uuid_gpt_loader1};name=loader2,size=984k,uuid=${uuid_gpt_loader2};name=esp,size=128M,bootable,uuid=${uuid_gpt_esp};name=system,size=-,uuid=${uuid_gpt_system}; partuuid=f9fc421d-01 pxefile_addr_r=0x43200000 ramdisk_addr_r=0x43300000 rootdev=UUID=7af2b6ff-a1ee-4678-af7e-2271601e558c rootfstype=ext4 scan_dev_for_boot=echo Scanning ${devtype} ${devnum}:${distro_bootpart}...; for prefix in ${boot_prefixes}; do run scan_dev_for_extlinux; run scan_dev_for_scripts; done; scan_dev_for_boot_part=part list ${devtype} ${devnum} -bootable devplist; env exists devplist || setenv devplist 1; for distro_bootpart in ${devplist}; do if fstype ${devtype} ${devnum}:${distro_bootpart} bootfstype; then run scan_dev_for_boot; fi; done scan_dev_for_extlinux=if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}extlinux/extlinux.conf; then echo Found ${prefix}extlinux/extlinux.conf; run boot_extlinux; echo SCRIPT FAILED: continuing...; fi scan_dev_for_scripts=for script in ${boot_scripts}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${script}; then echo Found U-Boot script ${prefix}${script}; run boot_a_script; echo SCRIPT FAILED: continuing...; fi; done scriptaddr=0x43100000 snum=ac00143c519446f23ce soc=sunxi stderr=serial stdin=serial stdout=serial tv_vdid=2078814848 uuid_gpt_esp=c12a7328-f81f-11d2-ba4b-00a0c93ec93b uuid_gpt_system=69dad710-2ce4-4e3c-b16c-21a1d49abed3 verbosity=1 Environment size: 3588/131068 bytes armbian# clear Unknown command 'clear' - try 'help' armbian# cls Unknown command 'cls' - try 'help' armbian# clsscr Unknown command 'clsscr' - try 'help' armbian# printenv arch=arm baudrate=115200 board=sunxi board_name=sunxi boot_a_script=load ${devtype} ${devnum}:${distro_bootpart} ${scriptaddr} ${prefix}${script}; source ${scriptaddr} boot_disp=1034 boot_disp1=0 boot_disp2=0 boot_extlinux=sysboot ${devtype} ${devnum}:${distro_bootpart} any ${scriptaddr} ${prefix}extlinux/extlinux.conf boot_fb0=7bf4fcc0,500,2d0,20,1400,1e0,f0,320,1e0 boot_prefixes=/ /boot/ boot_script_dhcp=boot.scr.uimg boot_scripts=boot.scr.uimg boot.scr boot_targets=fel mmc_auto pxe dhcp bootargs=root=UUID=7af2b6ff-a1ee-4678-af7e-2271601e558c rootwait rootfstype=ext4 console=ttyS0,115200 consoleblank=0 loglevel=1 ubootpart=f9fc421d-01 usb-storage.quirks= cgroup_enable=memory swapaccount=1 bootcmd=run distro_bootcmd bootcmd_dhcp=if dhcp ${scriptaddr} ${boot_script_dhcp}; then source ${scriptaddr}; fi; bootcmd_fel=if test -n ${fel_booted} && test -n ${fel_scriptaddr}; then echo '(FEL boot)'; source ${fel_scriptaddr}; fi bootcmd_mmc0=setenv devnum 0; run mmc_boot bootcmd_mmc1=setenv devnum 1; run mmc_boot bootcmd_mmc_auto=if test ${mmc_bootdev} -eq 1; then run bootcmd_mmc1; run bootcmd_mmc0; elif test ${mmc_bootdev} -eq 0; then run bootcmd_mmc0; run bootcmd_mmc1; fi bootcmd_pxe=dhcp; if pxe get; then pxe boot; fi bootdelay=1 bootfstype=ext4 bootlogo=false bootm_size=0xa000000 bootreason=unknow console=serial consoleargs=console=ttyS0,115200 cpu=armv7 devnum=0 devplist=1 devtype=mmc dfu_alt_info_ram=kernel ram 0x41000000 0x1000000;fdt ram 0x43000000 0x100000;ramdisk ram 0x43300000 0x4000000 disp_mode=1080p60 disp_reserve=3686400,0x7bf4fcc0 distro_bootcmd=for target in ${boot_targets}; do run bootcmd_${target}; done docker_optimizations=on fb0_height=720 fb0_width=1280 fdt_addr_r=0x43000000 fdtaddr=43000000 fdtcontroladdr=7be87560 fdtfile=sunxi/sun50i-h616-orangepi-zero2.dtb fileaddr=43300000 filesize=6abd13 kernel_addr_r=0x41000000 load_addr=0x45000000 mmc_boot=if mmc dev ${devnum}; then setenv devtype mmc; run scan_dev_for_boot_part; fi overlay_error=false partitions=name=loader1,start=8k,size=32k,uuid=${uuid_gpt_loader1};name=loader2,size=984k,uuid=${uuid_gpt_loader2};name=esp,size=128M,bootable,uuid=${uuid_gpt_esp};name=system,size=-,uuid=${uuid_gpt_system}; partuuid=f9fc421d-01 pxefile_addr_r=0x43200000 ramdisk_addr_r=0x43300000 rootdev=UUID=7af2b6ff-a1ee-4678-af7e-2271601e558c rootfstype=ext4 scan_dev_for_boot=echo Scanning ${devtype} ${devnum}:${distro_bootpart}...; for prefix in ${boot_prefixes}; do run scan_dev_for_extlinux; run scan_dev_for_scripts; done; scan_dev_for_boot_part=part list ${devtype} ${devnum} -bootable devplist; env exists devplist || setenv devplist 1; for distro_bootpart in ${devplist}; do if fstype ${devtype} ${devnum}:${distro_bootpart} bootfstype; then run scan_dev_for_boot; fi; done scan_dev_for_extlinux=if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}extlinux/extlinux.conf; then echo Found ${prefix}extlinux/extlinux.conf; run boot_extlinux; echo SCRIPT FAILED: continuing...; fi scan_dev_for_scripts=for script in ${boot_scripts}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${script}; then echo Found U-Boot script ${prefix}${script}; run boot_a_script; echo SCRIPT FAILED: continuing...; fi; done scriptaddr=0x43100000 snum=ac00143c519446f23ce soc=sunxi stderr=serial stdin=serial stdout=serial tv_vdid=2078814848 uuid_gpt_esp=c12a7328-f81f-11d2-ba4b-00a0c93ec93b uuid_gpt_system=69dad710-2ce4-4e3c-b16c-21a1d49abed3 verbosity=1 Environment size: 3588/131068 bytes armbian# mtest Unknown command 'mtest' - try 'help' armbian# ls ls - list files in a directory (default /) Usage: ls <interface> [<dev[:part]> [directory]] - List files in directory 'directory' of partition 'part' on device type 'interface' instance 'dev'. armbian# 0 Quote Link to comment Share on other sites More sharing options...
Werner Posted July 11, 2022 Share Posted July 11, 2022 Which exact image? 0 Quote Link to comment Share on other sites More sharing options...
ALIGMSTEN Posted July 11, 2022 Share Posted July 11, 2022 Doesn't look Armbian, seems to be Legacy image from Orangepi. [100]HELLO! BOOT0 is starting May 13 2020 14:10:04! [105]BOOT0 commit : 593cf83 U-Boot 2018.05-orangepi (Mar 31 2022 - 11:47:20 +0800) Xunlong Software [00.474]CPU: Allwinner H616 [00.477]Model: Orange Pi Zero 2 0 Quote Link to comment Share on other sites More sharing options...
Werner Posted July 11, 2022 Share Posted July 11, 2022 Or vendor kernel/uboot which is used in legacy images. 0 Quote Link to comment Share on other sites More sharing options...
ALIGMSTEN Posted July 11, 2022 Share Posted July 11, 2022 Oh ok interesting yes could be, do know about vendor source - haven't spent much time with Armbian legacy, still thought its debug was different to above output though. Anyway not helping! Back to @Werner 's question, if OP lets us know the exact image, perhaps some guidance can be given. 0 Quote Link to comment Share on other sites More sharing options...
gyrex Posted August 22, 2022 Share Posted August 22, 2022 (edited) After testing a few images in a bid to try and get a working image where wireless works, I can confirm that this issue happens with the current 'supported' Bullseye image: Armbian_22.05.3_Orangepizero2_bullseye_legacy_4.9.255.img As well as a bunch of other 'current' images in the archive. Edited August 22, 2022 by gyrex 0 Quote Link to comment Share on other sites More sharing options...
gyrex Posted August 22, 2022 Share Posted August 22, 2022 Boot log from Armbian_22.05.3_Orangepizero2_bullseye_legacy_4.9.255.img [64]HELLO! BOOT0 is starting May 13 2020 14:10:04! [69]BOOT0 commit : 593cf83 [72]set pll start [74]periph0 has been enabled [78]set pll end [79]unknow PMU [81]PMU: AXP806 [88]vaild para:1 select dram para0 [91]board init ok [93]DRAM BOOT DRIVE INFO: V0.52 [96]the chip id is 0x5000 [99]chip id check OK [101]DRAM_VCC set to 1500 mv [105]read_calibration error [109]read_calibration error [113]read_calibration error [117]read_calibration error [121]read_calibration error [125]read_calibration error [128]read_calibration error [132]read_calibration error [136]read_calibration error [140]read_calibration error [143]retraining final error [148][AUTO DEBUG]32bit,1 ranks training success! [155]DRAM CLK =720 MHZ [157]DRAM Type =3 (3:DDR3,4:DDR4,7:LPDDR3,8:LPDDR4) [164]Actual DRAM SIZE =1024 M [167]DRAM SIZE =1024 MBytes, para1 = 30fa, para2 = 4000000, dram_tpr13 = 6041 [180]DRAM simple test OK. [182]rtc standby flag is 0x0, super standby flag is 0x0 [188]dram size =1024 [190]*****dram handle ok**** [193]card no is 0 [195]sdcard 0 line count 4 [198][mmc]: mmc driver ver 2019-12-19 10:41 [202][mmc]: sdc0 spd mode error, 2 [205][mmc]: set f_max to 50M, set f_max_ddr to 25M [210][mmc]: mmc 0 bias 0 [218][mmc]: Wrong media type 0x0 [221][mmc]: ***Try SD card 0*** [231][mmc]: HSSDR52/SDR25 4 bit [234][mmc]: 50000000 Hz [236][mmc]: 29818 MB [238][mmc]: ***SD/MMC 0 init OK!!!*** [338]Loading boot-pkg Succeed(index=0). [342]Entry_name = u-boot [351]Entry_name = monitor [355]Entry_name = dtbo [357]Entry_name = dtb [361]Jump to second Boot. NOTICE: BL3-1: v1.0(debug):9fecd83 NOTICE: BL3-1: Built : 17:08:29, 2020-05-28 NOTICE: BL3-1 commit: 8 ERROR: Error initializing runtime service tspd_fast NOTICE: BL3-1: Preparing for EL3 exit to normal world NOTICE: BL3-1: Next image address = 0x4a000000 NOTICE: BL3-1: Next image spsr = 0x1d3 U-Boot 2018.05-armbian (Jun 22 2022 - 07:19:38 +0000) Xunlong Software [00.437]CPU: Allwinner H616 [00.440]Model: Orange Pi Zero 2 I2C: ready [00.445]DRAM: 1 GiB Relocation Offset is: 35ec7000 [00.485]secure enable bit: 0 [00.488]PMU: AXP806 [00.493]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=400Mhz [00.675]sunxi overlay merged okqv [00.678]drv_disp_init [00.707]__clk_enable: clk is null. tv_init()950 fetch tv0 err. [00.713]drv_disp_init finish [00.715]gic: sec monitor mode [00.721]flash init start [00.723]workmode = 0,storage type = 1 [00.726]MMC: 0 [00.728][mmc]: mmc driver ver uboot2018:2021-07-19 14:09:00 [00.734][mmc]: get sdc_type fail and use default host:tm1. [00.744][mmc]: Using default timing para [00.748][mmc]: SUNXI SDMMC Controller Version:0x40200 [00.766][mmc]: card_caps:0x3000000a [00.769][mmc]: host_caps:0x3000003f [00.773]sunxi flash init ok [00.776]Loading Environment from FAT... [00.780][mmc]: mmc driver ver uboot2018:2021-07-19 14:09:00 [00.786][mmc]: get sdc_type fail and use default host:tm1. [00.796][mmc]: Using default timing para [00.800][mmc]: SUNXI SDMMC Controller Version:0x40200 ** Bad device mmc 1 ** Failed (-5) [00.811]usb burn from boot delay time 0 weak:otg_phy_config [00.824]usb prepare ok [01.627]overtime [01.631]do_burn_from_boot usb : no usb exist [01.635]boot_gui_init:start 141 bytes read in 20 ms (6.8 KiB/s) Set HDMI disp_mode to 1080p60 141 bytes read in 20 ms (6.8 KiB/s) Set fb0_width to 1280 Set fb0_height to 720 [01.961]boot_gui_init:finish [01.963]bmp_name=/boot/boot.bmp 230454 bytes read in 44 ms (5 MiB/s) [02.021]update dts Net: [02.024]No ethernet found. Hit any key to stop autoboot: 0 no mmc device at slot 1 [03.051][mmc]: card_caps:0x3000000a [03.054][mmc]: host_caps:0x3000003f switch to partitions #0, OK mmc0 is current device Scanning mmc 0:1... Found U-Boot script /boot/boot.scr 3202 bytes read in 26 ms (120.1 KiB/s) ## Executing script at 43100000 U-boot loaded from SD Boot script loaded from mmc 141 bytes read in 19 ms (6.8 KiB/s) 262144 bytes read in 52 ms (4.8 MiB/s) ** File not found /boot/dtb/allwinner/overlay/-fixup.scr ** 6995219 bytes read in 622 ms (10.7 MiB/s) ** File not found /boot/Image ** Unknown command 'booti' - try 'help' SCRIPT FAILED: continuing... No ethernet found. missing environment variable: pxeuuid missing environment variable: bootfile Retrieving file: pxelinux.cfg/00000000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/0000000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/000000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/00000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/0000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/00 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/0 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/default-arm-sunxi No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/default-arm No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/default No ethernet found. Config file not found No ethernet found. armbian# % 0 Quote Link to comment Share on other sites More sharing options...
ALIGMSTEN Posted August 22, 2022 Share Posted August 22, 2022 Hi @gyrex, I haven't read all your posts, perhaps you have already tried. (EDIT: see you have!) Last working legacy image I booted from: Armbian_22.02.2_Orangepizero2_bullseye_legacy_4.9.255.img Have various images in various states of experimental chaos, but have used this above for legacy where all was working, well, I mainly use headless, and minimal builds and then add what needed for purpose, so stand to be corrected on features. 0 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.