Cesar Inacio Martins Posted March 27, 2023 Posted March 27, 2023 (edited) Hi! I'm new to armbian and just installed it on my KI PRO , AmLogic s905d . I've compiled my own version using the last build . Use the image to generic tvb for s905 with debian 11. to configure the boot I use the KII PRO dtb : /boot/extlinux/extlinux.conf Quote FDT /dtb/amlogic/meson-gxl-s905d-mecool-kii-pro.dtb The box is running very well , however I have two issue with it. One of them is with eth0 doesn't recognize the cable connected . I saw the answer here about @mrv issue and found no solution until now. I'm not sure where I can try any other module to test my ethernet card... Generated my armbianmonitor : https://paste.armbian.com/vomagohelu any tips? Edited March 27, 2023 by Cesar Inacio Martins better explanation
SteeMan Posted April 8, 2023 Posted April 8, 2023 @Cesar Inacio Martins Have you tried to use armbian-config to configure your networking? From the armbianmonitor output it appears you have valid eth0 and wlan0 interfaces.
Cesar Inacio Martins Posted April 24, 2023 Author Posted April 24, 2023 Hi @Steeman, No , doesn't work. At first, I'm using the nmtui to configure, but even with armbian-config , still not working. If I tried to force an IP to eth0 and start it, the network froze and even my wifi access stop to work, then I need to log on console and put down the eth0. I notice this message "interrupt 34" for the eth0 , however didn't found anything useful to try identify if is related with my problem. Quote eth0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500 ether 56:13:5b:51:7a:8f txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 34 Quote ┌──────────────────────────Select interface─────────────────────────────┐ │ ┌────────────────────────────────────────────────────────────────────┐ │ │ │ wlan0 192.168.5.235 Speed: 540Mbit/s │ │ │ │ docker0 172.17.0.1 │ │ │ │ eth0 Speed: Unknown! │ │ │ │ p2p-dev-wlan0 │ │ │ │ veth4a44d98 │ │ │ └────────────────────────────────────────────────────────────────────┘ │ ├────────────────────────────────────────────────────────────────────────┤ │ < OK > │ └────────────────────────────────────────────────────────────────────────┘ Quote [ +0.374493] meson8b-dwmac c9410000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0 [ +0.066894] meson8b-dwmac c9410000.ethernet eth0: PHY [mdio_mux-0.e40908ff:08] driver [Meson GXL Internal PHY] (irq=44) [ +0.012917] meson8b-dwmac c9410000.ethernet eth0: No Safety Features support found [ +0.000037] meson8b-dwmac c9410000.ethernet eth0: PTP not supported by HW [ +0.007833] meson8b-dwmac c9410000.ethernet eth0: configuring for phy/rmii link mode ... [ +1.560358] eth0: renamed from veth97543c5 Quote root@box:~ # ethtool eth0 Settings for eth0: Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Advertised pause frame use: Symmetric Receive-only Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Speed: Unknown! Duplex: Unknown! (255) Auto-negotiation: on Port: Twisted Pair PHYAD: 8 Transceiver: internal MDI-X: Unknown Supports Wake-on: ug Wake-on: d Current message level: 0x0000003f (63) drv probe link timer ifdown ifup Link detected: no root@box:~ #
Recommended Posts