Jump to content

Banana Pi M3 crashes if ETH plugged


bahtiyar57
Go to solution Solved by bahtiyar57,

Recommended Posts

I've no problem using my Banana Pi with a wifi connection.

But if I plug it on my router with a ethernet cable it crashs after a short time.

Should I upload the output of armbianmonitor when ETH is plugged?
Because it will take me a few tries, to do that.

Link to comment
Share on other sites

4 часа назад, bahtiyar57 сказал:

I've no problem using my Banana Pi with a wifi connection.

But if I plug it on my router with a ethernet cable it crashs after a short time.

Boot the system in the case when it is stable, i.e. with wi-fi.
Look at the system logs and post the one when the Ethernet connection failed.

Link to comment
Share on other sites

16 часов назад, bahtiyar57 сказал:

I've no problem using my Banana Pi with a wifi connection.

I have a question. If it works well, why switch to another interface (Ethernet)?

 

This device does not have a battery-powered clock and it requires the Internet

to get an accurate time stamp from the time server and set the SOC's internal clock in real time.

 

You have disabled WI-FI and connected Ethernet.
Do the settings in the connection management system look correct now?
Is the network cable working?
Does the banana receive the DHCP settings from the router?

Did the router have Internet access at the time of banana connection?


You didn't write anything about it.

Just for reference.

There has been a strong magnetic storm on our planet for the last two days.

My Internet went down several times for one hour or more.

Link to comment
Share on other sites

33 минуты назад, bahtiyar57 сказал:

But after a short time the Board shuts down.

If you downloaded a banana from the SD card and a failure occurred,

simply turn off the device, take out the SD card and connect it to a Linux computer via the adapter.

Find the latest system logs and review them.

Link to comment
Share on other sites

@bahtiyar57

18 часов назад, bahtiyar57 сказал:

Or can you help me to use it without destroying anything?

 

22 часа назад, Werner сказал:

Better method would probably be using debug serial console to grab the output while the crash happens.

https://debug.armbian.de

 



_________________                     FTDI232
  BPI            |               _________________
                 |               |        3.3v    |_____ ____
  UART      GND o|---------------|o GND  o|       |    ||    |                | Linux
            TX  o|---------------|o RX   o|       | USB||    |====USB cable===| console
            RX  o|---------------|o TX   o        |____||____|                | "minicom"
_________________|               |________5v______|

o| 3.3v

o|

This is the jumper on the device.
I use this scheme. Everyone uses this scheme. It's safe.

Link to comment
Share on other sites

Thank you. I undestand that. What I have to do after I plugged the serial console in.
I know I have to use Putty in Windows and configure the seria line to 115200.

And then?

 

EDIT:
Maybe I'm wrong, but I think it's a voltage problem.

Edited by bahtiyar57
Link to comment
Share on other sites

This is very complicated for me. Because I don't know how I have to do it exactly?
I used a time a very old Easy-Box 802. And with this it didn't crashed.

With my FritzBox 7490 and 7520 it will crash.

Know I will try to disable EEE (Energy Efficient Ethernet) on my Router.

I read that some peolpe had problems with this. But they diabled it with adding:

dtparam=eee=off

to /boot/config.txt

Or by running this command:

ethtool --set-eee eth0 eee off

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
×
  • Create New...

Important Information

Terms of Use - Privacy Policy - Guidelines