gondim Posted January 28, 2017 Share Posted January 28, 2017 Hi all, I need a help. I installed the armbian Debian Jessie 4.9.5 in my cubietruck. It is connected via HDMI. How do I set the output of sound to be HDMI? Thanks and best regards Link to comment Share on other sites More sharing options...
Igor Posted January 28, 2017 Share Posted January 28, 2017 https://forum.armbian.com/index.php/topic/397-mainline-a10a20-audio-driver/?p=24186 Link to comment Share on other sites More sharing options...
gondim Posted January 28, 2017 Author Share Posted January 28, 2017 Hi Igor, If I used armbian legacy 3.4.113. Would it be easier to change audio output to HDMI? Link to comment Share on other sites More sharing options...
Igor Posted January 28, 2017 Share Posted January 28, 2017 Yes, HDMI audio works out of the box on legacy / 3.4.113 Link to comment Share on other sites More sharing options...
gondim Posted January 28, 2017 Author Share Posted January 28, 2017 Hi Igor, With armbian Debian 3.4.113 the cubietruck wifi not work but with mainline 4.9.5 it´s works. Is there any configuration for it to work in 3.4.113? # iwconfig wlan0 wlan0 IEEE 802.11 Acess Point: Not-Associated Link Quality:0 Signal level:0 Noise level:0 RX invalid nwid:0 invalid crypt:0 invalid misc:0 Do I need to load any modules? I tried: # modprobe bcmhd Modprobe FATAL: Module bcmhd not found. Thanks Link to comment Share on other sites More sharing options...
Igor Posted January 29, 2017 Share Posted January 29, 2017 We don't use that module since some time ... ap6211 and check if firmware is in place and loaded. In any case, logs would drastically help to see what's wrong armbianmonitor -u Link to comment Share on other sites More sharing options...
gondim Posted January 29, 2017 Author Share Posted January 29, 2017 Hi Igor, Thanks for your help! http://sprunge.us/DPeQ Ah! Reboot and shutdown cause kernel panic in 3.4.113. I remember that with the 3.4.112 kernel this did not happen. Link to comment Share on other sites More sharing options...
Igor Posted January 29, 2017 Share Posted January 29, 2017 Driver should be ap6210 ... sorry. Check my bootlog. Wifi is working fine http://sprunge.us/Beed root@cubietruck:~# iwconfig wlan0 wlan0 IEEE 802.11 ESSID:"XXXXX" Mode:Master Frequency:2.427 GHz Access Point: XX:XX:XX:XX:XX:XX Bit Rate=65 Mb/s Tx-Power:32 dBm Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link to comment Share on other sites More sharing options...
gondim Posted January 29, 2017 Author Share Posted January 29, 2017 Driver should be ap6210 ... sorry. Check my bootlog. Wifi is working fine http://sprunge.us/Beed root@cubietruck:~# iwconfig wlan0 wlan0 IEEE 802.11 ESSID:"XXXXX" Mode:Master Frequency:2.427 GHz Access Point: XX:XX:XX:XX:XX:XX Bit Rate=65 Mb/s Tx-Power:32 dBm Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Very strange. Can it be the cubietruck review? I can not see the review of my cubietruck because it already came with the heatsink on the processor. When I use mainline version 4.9.5, the wifi works correctly. I am trying to connect cubietruck as a client of my routerboard. I'll try some more tests here. Anyway thanks for the help Igor. Link to comment Share on other sites More sharing options...
Recommended Posts