wdtz

Members
  • Content Count

    46
  • Joined

  • Last visited

Everything posted by wdtz

  1. >I'm willing to try any builds, configs, and pretty much anything else anyone can think of, short of soldering, Do some dtb hacking? All the memory timing is in this, maybe the mem is pushed too far, too hard? But, it is plenty complicated, looking at 5x, much of the detail is gone, so applies to 4x mostly
  2. wdtz

    Pinebook Pro

    OK, a bit more update, I did try a nightly, mostly works OK one boot(early) needed a vt, black screen and oddly, caps,num were not active so I didn't think it had booted, well, give it a try,, whoa!! whats this! One did a hard lock, the first IIRR Since it has been booting without problem (This is using its own uboot) Sleep, so far is only s2idle, deep fails to wake Despite ACPI and a change to legacy uboot, have not gotten S3 sleep S3 on manjaro, elementary, fedora,, sleep is 7%/d, fast too,, so makes running off SD feasible (if you're not a reboo
  3. @TDCroPower I have to wonder if you have a uboot (&equally important, idbloader) on your emmc If you run fdisk on emmc is there room,,1st part start at 32768 (or >)? What the boot rom is looking for is idblaoder, well, a raw read for the signature bytes 3B 8C DC FC BE 9F 9D 51 (so far, all idbloaders are same here) I guess it is assumed that if idbloader is there (on that media), then so will uboot So, something like..... dd if=/dev/emmc of=test skip=64 count=1 then,,,,, hexedit test
  4. wdtz

    Pinebook Pro

    No, this is a perhaps week old download, updated Armbian_20.08.4_Pinebook-pro_focal_current_5.8.11_desktop.img.xz
  5. wdtz

    Pinebook Pro

    https://forum.pine64.org/showthread.php?tid=10694&page=6 ,, post 58 & on Oddly I had a great deal of trouble getting anything but black screen, probably booted 'cause capslock toggle worked (leds) The bsp uboots gave 'hard locks' (mrfix, pcm), now using samueldr, 1 in 5 boots My pbp is a bit unusual, emmc uboot area blanked, so forced to use SD uboot If sleep to mem works, doesn't matter if SD is slow, resume to desktop is 10-12 s, another 10 for wifi But I have not found how to resume armbian, so no idea how well it does
  6. Well, if you have serial terminal.... >the device loads first the uboot from the emmc I doubt that there is one (on the emmc) So then it looks at SD, loads 1st idbloader, then uboot, then ATF (arm trusted firmware),, all from uSD I would say that either your emmc/controller are bad or dtb is not right copy boot.* as backup, try other dtbs,, since it is a H96+ also write image to a usb stick,, many dtb have a wrong regulator setting for SD power, uboot is OK, then SD is dead with kernel usb stick will still work, see if fdisk works with different dtb (
  7. >Buffer I/O error on dev mmcblk1, logical block 0, lost async page write >/dev/mmcblk1: close device failed: Input/output error I think something is wrong with hardware, perhaps try a different (but compatible) dtb OR try dd if=/dev/zero of=emmc bs=1M count=20 (change emmc as appropriate) Do be sure to run fdisk again, command p ,, q,, just to see if error msg was correct And, PLEASE start first partition at 32768 sectors (16M). Most distros expect unpartitioned space for idbloader(start 64 sec), uboot (8M, 32384) and ATF (not sure). sometimes
  8. Why would you not use fdisk on the emmc to define and format partitions? Do start at 16M, 32768 sectors for the first, 2-300M,, fat, type c and the rest linux, type 83,, mkdosfs -F32 /dev/mmcblk1p1,, mkfs.ext4 .......p2 All as root (16M = 16*1024*2 sectors,,, space for idbloader, uboot, tfm) If the emmc is bad, you will get lots of errors
  9. That's the error for a misconfigured dtb, the voltage supply to mmc, @500000 and 5100000 A non-standard regulator setup, like t9 or h96max+
  10. OK, i'll make an attempt, please correct me where wrong dtc is kind of stupid, and device trees could definitely be improved I'll bet you don't have a compiler environment and that's the problem an example line, still symbolic,,, gpios = <&gpio2 RK_PA2 GPIO_ACTIVE_HIGH>; The <&something,,> is an internal (only?) pointer in the dtb The next 2 elements are probably populated from an appropriate .h (header) file (specific to that hardware) So it becomes,,, gpios = < 0x3e 0x02 0x01 >; ( a random example) The dtc compiler can only
  11. So, Digit97 , you never 'got back' to us to say how it worked out and what you found
  12. understand, uboot and kernel have different dtb, that is why h96max+ starts, with uboot as seen by serial cable, but then when hands over to kernel dtb does not power uSD slot, something non-standard with regulators. So, it can't find its root filesystem, because slot is dead, no power You see no hdmi display until quite late in the boot, so it seems dead, just can't read uSD slot It there is a usb stick ALSO plugged in, will find root fs on usb stick.. uSD slot continues dead, unpowered easyb and hexdump have made dtb for h96max+/T9 that make regulators work.
  13. I hope you don't expect me to do it for you? I am going to assume that you have broken that image up into the partition images I don't know if you are using win or linux, no matter There are hexeditors for both, a gui vesion is my recommendation, wxHex or okteta or ghex, I tend to use okteta load kernel.img into hexeditor, control f , make sure the hex button is selected, enter the signature above. It will be a good sign if it is found at the begining of the line, make a note of the address, keep searching. Then, in calculator, set decimal , address/1024, s
  14. Are you saying that there is no resource.img? You do know that the dtb is 2K into resource.img (IIRR)? use dd to strip Sometimes the dtb is appended to the kernel,,, anyway search, with a hexeditor for D0 0D FE ED 00, at an even K boundry d00dfeed00 it the "signature" for dtb's. Most dtbs are about 60-65K in size Most of the resource.img is an (graphic) image file (or 2) for the splash screen I haven't found android dtbs to be very useful And, BTW how well does easyb's dtb work for you,, does everything work, both usb, ethernet? I have 46d uptime, I seldom reboo
  15. Digit: with a working and non-working situation,, compare lsusb ,,, lsusb | wc -l ,,, dmesg | tail -15 (just after dongle inserted,, ie unplug, replug) as root/sudo,,, lsmod | grep ath ,,, ifconfig If it doesn't show with lsusb, check the other port, for me, hexdump's dtb conflicts usb2 and debug, doesn't work,, and usb3 locks hub on a daily basis, needs a replug, 3 different hubs Haven't tried easyb's dtb yet
  16. I am wondering what version of linux is this running under? I am not familiar with libre-elect
  17. >I have tried the conversion from dts to dtb but i not have success. Try again,,, dtc -h,, must be dtb,,, dts is only for editing/altering,,, kernel wants dtb Let us know how it goes Because of the symbolic names, if you don't have a compile environment it probably won't work
  18. I guess you have not read much of this thread, last5-6 pages would be good t9.dtb for 4.4.x kernel seems OK, I have not tried any 5.x, slightly different dtb (guess) Not on ups, 10d uptime,, H96max+, wifi dongle a bit unstable, needs powered hub, x11vnc Oh, and if hub back-feeds (many do) must unplug for reboot or power off For example, a 2 second power "blink", you will think box is dead, until you unplug hub power too
  19. @hexdump Thanks for your t9.dtb,, works fine with H96 max+ for me I could never figure out how the regulators worked, somehow you did Only thing lacking is module for SSV6051 I guess I should try to put patch in right place and make a kernel
  20. Board is labeled RK3328_8D4_V1.1, same as yours, wifi chip is indeed different, SV6051P Serial connection as shown in your photo I think the problem with sd card is power to socket, if you read this thread I have a few posts previous
  21. I have H96 max+,32gb, board is same, wifi is sv6051, no bluetooth Like you, most of the dtb give root fs not found, no /dev/block/mmc.... ,, or for the android versions a black screen, serial shows only a few lines of kernel load (<5) --edit-- you can make it work by writing image to both a uSD card and a usb stick, it will probably find the stick and run from it. The uSd can be small and slow Not so good with only 2 usb sockets
  22. Can you quote some specific models? My H96max+, android8.1 seemed OK,, SuperSU installed OK, root checker said all was well
  23. Err,, adb is not "android",, android is the graphical shell,, hypothetical example,, if you had firefox installed,, typing firefox in adb would NOT startup firefox But, for sure , adb is very powerful, despite being a considerable pain More on point, adb uses the su in /sbin,, android uses the su in /system/xbin,, it is no good
  24. Clearly,, you have not read whole thread,, about 5 pages back, but differently in adb# ,, ls -l /sbin/su; ls -l /system/xbin/su ,, notice that they are not the same? (google) verity off; mount -o remount,rw /system; cd /system/xbin; mv su su.bak; cp /sbin/su . and then root will work in android FWIW
  25. I have one of these, in the simple shell ls -l /dev/block will show at best mmcblk1 (the emmc), (almost) never the sd card I think it's something to do with the regulator,, pwm does not seem to work,, the android dtb seem to use simpleReg vrs rk805-regulator I did a "hack" bypassing gpio, barely works, lots of errors in dmesg (regulator errors,, boots and runs from sd) The other method is to copy rootfs to a usb stick, rename the partitions (e2label)