1 1
Wu Min

espressobin install to eMMC

Recommended Posts

when I used the command "nand-sata-install" ,then i  select The first one, install Armbian from the SD card to the Built in emmc, After step-by-step execution, I will prompt poweroff. Then I remove the SD card and prepare to start from EMMC. However, the following error prompt appears. I cannot enter the system from EMMC normally,Please help me, thank you

 

micro sd install.JPG


TIM-1.0
WTMI-devel-18.12.1-e6bb176
WTMI: system early-init
CPU VDD voltage default value: 1.155V
NOTICE: Booting Trusted Firmware
NOTICE: BL1: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
NOTICE: BL1: Built : 16:23:10, May 21 2019
NOTICE: BL1: Booting BL2
NOTICE: BL2: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
NOTICE: BL2: Built : 16:23:11, May 21 2019
NOTICE: BL1: Booting BL31
NOTICE: BL31: v1.5(release):1f8ca7e (Marvell-devel-18.12.2)
NOTICE: BL31: Built : 16:2

U-Boot 2018.03-devel-18.12.3-gc9aa92c-armbian (Feb 20 2019 - 09:45:04 +0100)

Model: Marvell Armada 3720 Community Board ESPRESSOBin
CPU 1000 [MHz]
L2 800 [MHz]
TClock 200 [MHz]
DDR 800 [MHz]
DRAM: 1 GiB
Comphy chip #0:
Comphy-0: USB3 5 Gbps
Comphy-1: PEX0 2.5 Gbps
Comphy-2: SATA0 6 Gbps
SATA link 0 timeout.
AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
flags: ncq led only pmp fbss pio slum part sxs
PCIE-0: Link down
MMC: sdhci@d0000: 0, sdhci@d8000: 1
Loading Environment from SPI Flash... SF: Detected w25q32dw with page size 256 Bytes, erase size 4 KiB, total 4 MiB
OK
Model: Marvell Armada 3720 Community Board ESPRESSOBin
Net: eth0: neta@30000 [PRIME]
Hit any key to stop autoboot: 0
starting USB...
USB0: Register 2000104 NbrPorts 2
Starting the controller
USB XHCI 1.00
USB1: USB EHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
scanning bus 1 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
/
** Bad device usb 0 **
## Executing script at 06d00000
Wrong image format for "source" command
/boot/
** Bad device usb 0 **
## Executing script at 06d00000
Wrong image format for "source" command
scanning bus for devices...

Device 0: unknown device
/
** Bad device scsi 0 **
## Executing script at 06d00000
Wrong image format for "source" command
/boot/
** Bad device scsi 0 **
## Executing script at 06d00000
Wrong image format for "source" command
/
** File not found /boot.scr **
## Executing script at 06d00000
Wrong image format for "source" command
/boot/
1119 bytes read in 15 ms (72.3 KiB/s)
## Executing script at 06d00000
240 bytes read in 4 ms (58.6 KiB/s)
Card did not respond to voltage select!
** Bad device mmc 0 **
Card did not respond to voltage select!
** Bad device mmc 0 **
Card did not respond to voltage select!
** Bad device mmc 0 **
Card did not respond to voltage select!
** Bad device mmc 0 **
Bad Linux ARM64 Image magic!
/
Card did not respond to voltage select!
** Bad device mmc 0 **
## Executing script at 06d00000
Wrong image format for "source" command
/boot/
Card did not respond to voltage select!
** Bad device mmc 0 **
## Executing script at 06d00000
Wrong image format for "source" command
Marvell>>

 

Share this post


Link to post
Share on other sites
Armbian is a community driven open source project. Do you like to contribute your code?

Well, take a close look at your hardware - is the emmc installed?? Just because you bought it doesn't mean you got what you paid for. emmc is an OPTION on the espressobin v5 and v7.

 

I have a v5 without emmc and it gives an error if I try to install to emmc.

 

Look under the board - on a v5 with the ethernet ports oriented toward you there should be four chips to the right of center. Is there a place for a fourth one with an outline and no chip? No emmc ...

 

Espressobin v5 bottom

 

 

Share this post


Link to post
Share on other sites

Thank‘s for your reply. My version is V5, which confirms that EMMC has been installed on the backplane.

Share this post


Link to post
Share on other sites

You should edit the /boot/boot.cmd, change mmc device to 1:1 (eMMC) then:

mkimage -C none -A arm -T script -d /boot/boot.cmd /boot/boot.scr

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
1 1