Jump to content

Orange Pi +2E: USB devices cannot be detected


dmitryp

Recommended Posts

Armbianmonitor:

I recently updated from very old Armbian image. The update was not smooth so I had to re-image my device with the newest version. After that USB devices cannot be detected at all. I tried USB keyboard and 3D printer (is should looks like generic serial device). Keyboard works perfectly during u-boot but stops working as soon as kernel starts. lsusb doesn't show any devices:

$ lsusb -t
/:  Bus 09.Port 1: Dev 1, Class=root_hub, Driver=musb-hdrc/1p, 480M
/:  Bus 08.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M
/:  Bus 07.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M
/:  Bus 06.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M
/:  Bus 05.Port 1: Dev 1, Class=root_hub, Driver=ehci-platform/1p, 480M
/:  Bus 04.Port 1: Dev 1, Class=root_hub, Driver=ehci-platform/1p, 480M
/:  Bus 03.Port 1: Dev 1, Class=root_hub, Driver=ehci-platform/1p, 480M
/:  Bus 02.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M
/:  Bus 01.Port 1: Dev 1, Class=root_hub, Driver=ehci-platform/1p, 480M

So it seems like some generic issue with USB support. Now I'm using kernel 5.4.20-sunxi, also tried 4.19.104-sunxi and some other available in armbian-config - all give the same result.

 

Any help with making it work again is very appreciated.

Link to comment
Share on other sites

12 minutes ago, dmitryp said:

Any help with making it work again is very appreciated.


When updating from legacy kernels, you need to manually (from armbian-config) update boot loader. If this doesn't help ... no idea. Is USB on clean image working well?

Link to comment
Share on other sites

14 minutes ago, Igor said:


When updating from legacy kernels, you need to manually (from armbian-config) update boot loader. If this doesn't help ... no idea. Is USB on clean image working well?

I did boot loader update several times when I tried to fix problems after OS update. Now I did it one more time and rebooted the device - still no USB devices detected.

When I boot from SD card with current Armbian image there is the same issue with non-functional USB keyboard. With Orange Pi OS image from Orange Pi site there is no problem with USB devices but it is very old :(

Link to comment
Share on other sites

1 minute ago, dmitryp said:

When I boot from SD card with current Armbian image there is the same issue with non-functional USB keyboard.

 

Just your USB keyboard (low priority problem which you can also solve) is not working or not a single USB device (higher priority problem)? Did you tried all ports? Did you try to enable all USB ports in armbian-config -> system -> hardware ? Perhaps there was a change in upstream DT configuration that slipped by without notice.

I am sure USB ports were working  on this board last time I tried but can't double check for this particular build since I have no access to hardware until next week. I hope some other Opi 2e owner will be able to do that.

Link to comment
Share on other sites

2 minutes ago, Igor said:

 

Just your USB keyboard (low priority problem which you can also solve) is not working or not a single USB device (higher priority problem)? Did you tried all ports? Did you try to enable all USB ports in armbian-config -> system -> hardware ? Perhaps there was a change in upstream DT configuration that slipped by without notice.

I am sure USB ports were working  on this board last time I tried but can't double check for this particular build since I have no access to hardware until next week. I hope some other Opi 2e owner will be able to do that.

It is not only keyboard, it seems that no USB devices can be detected. I tried all 4 ports and following devices: keyboard, mouse, SD card reader and 3D printer - lsusb shows no devices at all, only root hub as in my first message.

 

When I try to "armbian-config -> system -> hardware", I see lots of errors from grep like:

Usage: grep [OPTION]... PATTERN [FILE]...
Try 'grep --help' for more information.
Usage: grep [OPTION]... PATTERN [FILE]...
Try 'grep --help' for more information.  
...

After that I see full screen of empty "[]", see picture attached.

 

9 minutes ago, martinayotte said:

I've just tested with USB Storage on my OPi2E running DEV 5.5.0, it is working.

BTW, on the OPi2E, all USBs are enabled by default directly in Main DT ...

I don't understand why I see so different picture with Bionic current image fresh install :(

conf.png

Link to comment
Share on other sites

My bad I found what was wrong in my case. I was using image for "Orange Pi +2E" but my board is "Orange Pi+ 2". Just tried correct image and now I see USB devices and problem with "armbian-config -> system -> hardware" has gone also.

 

I'm so sorry for the false alarm :(

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.
×
×
  • Create New...

Important Information

Terms of Use - Privacy Policy - Guidelines