TarasBY Posted May 12, 2020 Posted May 12, 2020 (edited) I can not raise the Access Point. Already my head is spinning on the number of tried recipes from the Internet. Service information here. Help me please. Configuration files:/etc/hostapd.conf ssid=BananaPI-WiFi interface=wlan0 hw_mode=g channel=5 bridge=br0 driver=nl80211 logger_syslog=1 logger_syslog_level=2 wmm_enabled=1 wpa=2 preamble=1 wpa_psk=c86e997b3dceff9bd7ffaf3f7353099a301c2**********d10a892c33cafcb5db wpa_passphrase=10********IV wpa_key_mgmt=WPA-PSK wpa_pairwise=TKIP rsn_pairwise=CCMP auth_algs=1 macaddr_acl=1 noscan=0 ### IEEE 802.11n #ieee80211n=1 #ht_capab= #country_code=US #ieee80211d=1 ### IEEE 802.11n ### IEEE 802.11a #hw_mode=a ### IEEE 802.11a ### IEEE 802.11ac #ieee80211ac=1 #vht_capab=[MAX-MPDU-11454][SHORT-GI-80][TX-STBC-2BY1][RX-STBC-1][MAX-A-MPDU-LEN-EXP3] #vht_oper_chwidth=1 #vht_oper_centr_freq_seg0_idx=42 ### IEEE 802.11ac # controlling enabled ctrl_interface=/var/run/hostapd ctrl_interface_group=0 /etc/dnsmasq.conf interface=wlan0 # Use interface wlan0 listen-address=192.168.42.1 # Explicitly specify the address to listen on bind-interfaces # Bind to the interface to make sure we aren't sending things elsewhere server=8.8.8.8;192.168.1.101; # Forward DNS requests to Google DNS domain-needed # Don't forward short names bogus-priv # Never forward addresses in the non-routed address spaces dhcp-range=192.168.42.10,192.168.42.100,24h # Assign IP addresses between 172.24.1.50 and 172.24.1.150 with a 12 hour lease time /etc/resolv.conf nameserver 127.0.0.1 /etc/dhcp/dhcpd.conf ddns-update-style none; authoritative; subnet 192.168.42.1 netmask 255.255.255.0 { range 192.168.42.10 192.168.42.100; option broadcast-address 192.168.42.255; option routers 192.168.42.1; default-lease-time 600; max-lease-time 7200; option domain-name "local"; option domain-name-servers 8.8.8.8, 8.8.4.4; } /etc/default/isc-dhcp-server INTERFACESv4="wlan0" INTERFACESv6="wlan0" /etc/network/interfaces source /etc/network/interfaces.d/* # Network is managed by Network manager auto lo iface lo inet loopback #auto eth0 # iface eth0 inet dhcp allow-hotplug eth0 iface eth0 inet static #alow-hotplug eth0 address 192.168.1.102 netmask 255.255.255.0 gateway 192.168.1.101 dns-nameservers 192.168.1.101 #auto wlan0 #iface wlan0 inet dhcp allow-hotplug wlan0 iface wlan0 inet static address 192.168.42.1 netmask 255.255.255.0 auto wlx000da31d4105 iface wlx000da31d4105 inet dhcp wpa_ssid STP_NET wpa_psk 10********63 #wpa-conf /etc/network/wpa_supp.conf #wpa-conf /etc/wpa_supplicant/wpa_supplicant.conf /etc/network/interfaces.d/armbian.ap.nat allow-hotplug wlan0 iface wlan0 inet static address 192.168.42.1 netmask 255.255.255.0 network 192.168.42.0 broadcast 192.168.42.255 /etc/network/wpa_supp.conf network={ #proto=WPA2 #pairwise=CCMP TKIP key_mgmt=WPA-PSK #priority=5 scan_ssid=1 ssid="STP_NET" #bssid=30:0c:23:bf:8c:1a #psk=97dbbf104f1f1e4e4ec61ab84b2adc40af*************e3161a6fa4b56da911 psk=10********63 } /etc/wpa_supplicant/wpa_supplicant.conf #network={ # ssid="STP_NET" # psk="***********" # psk=97dbbf104f1f1e4e4ec61ab*******************38ae3161a6fa4b56da911 #} /etc/NetworkManager/system-connections/Armbian ethernet.nmconnection [connection] id=Armbian ethernet uuid=722668d8-a507-423c-9d76-3a009a652da2 type=ethernet interface-name=eth0 permissions= timestamp=1589196940 [ethernet] mac-address-blacklist= [ipv4] address1=192.168.1.102/24,192.168.1.101 dns=8.8.8.8;192.168.1.101; dns-search= method=manual route-metric=78 [ipv6] addr-gen-mode=stable-privacy dns-search= method=auto /etc/NetworkManager/conf.d/armbian-default-metric.conf [connection-ethernet-gateway] match-device=interface-name:eth0 ipv4.route-metric=50 [connection-wifi-other] match-device=type:wifi # add row match-device=interface-name:wlan0 ipv4.route-metric=88 [connection-ethernet-other] match-device=type:ethernet ipv4.route-metric=77 Edited May 12, 2020 by TarasBY
TarasBY Posted May 18, 2020 Author Posted May 18, 2020 Thank you very much, gentlemen, for helping! And so quickly! I’m still tormented by the question: "Why did I buy Banana Pi?"
Igor Posted May 19, 2020 Posted May 19, 2020 21 hours ago, TarasBY said: Thank you very much, gentlemen, for helping! And so quickly! By downloading free software you didn't get free premium support or any rights to complain about. This is best effort support forum: https://github.com/armbian/build#support Ask, if no answer, research more -> if you need a solution, pay for help / DIY. Technical questions can't be solved without focusing into it. For that someone needs to be up to date and have to find time to pick up "clients" problem. There are about 1000x more people that seek help, then give. Have you used search before to help making this ratio more pleasant for those who give help? There are many similar ideas on this forum. I am sure you could get some clues if not a solution. Since we don't (pay for) support this hardware, there is a great chance nobody is listening ... sorry. You should be aware of that. 21 hours ago, TarasBY said: I’m still tormented by the question: "Why did I buy Banana Pi?" Rather support software development which is the only way you will get some rights to complain - cheap hardware without is a paperweight. Currently you - users - are not covering download costs, which means demanding help - 100% on our expense - is at least rude if nothing worse. Demanding free 1000 USD valued help is ... no words for that. Doing something for the project or community first, then asking for help .... can perhaps change things.
TarasBY Posted May 19, 2020 Author Posted May 19, 2020 3 hours ago, Igor said: My sincere sympathy for you - you did not have to spend so many useless words. I rarely ask for help - only as a last resort. I’ve been working with a computer for 30 years, but in this case, after an almost week-long battle with this board, I had to ask for outside help. But as always - saving a drowning man is the problem of the drowning man himself. No problems!
Igor Posted May 19, 2020 Posted May 19, 2020 7 minutes ago, TarasBY said: saving a drowning man is the problem of the drowning man himself ... as we are drowning in the flow of (mainly unrelated to our work) questions that are coming up every day. 12 minutes ago, TarasBY said: after an almost week-long battle with this board Welcome to the battleground If you would asked before whether is it worth fighting it, I would save you a week ... I have that kind of experiences which I am glad to share with you. This know-how is manifested in our labels: "WIP", "COMMUNITY SUPPORT", "SUPPORT", "EOS". For your own good, you don't want to ignore them, but do ignore sales messages, "review" sites, users hype fueled by impressions and marketing, ... 30 minutes ago, TarasBY said: I’ve been working with a computer for 30 years Use supported hardware. Even that is not a guarantee, but it's a much more solid ground. A place where one person (with 20-30 years of general computer / Linux experience) can do something useful. In this case, its useless since lower level support is fragile, immature and unstable. If you want all this to work, you have to fix many things - if you have seniority in this field and you will need to find some friends. Alone is always hard. You have to lead and be a developer. On our forum you can find useful clues which will save you time ... 26 minutes ago, TarasBY said: so many useless words Perhaps they are useless for your battle, but it might save somebody else's week. 1
TarasBY Posted May 19, 2020 Author Posted May 19, 2020 (edited) 9 hours ago, Igor said: Тёзка, я не понимаю: "Зачем тратить время (своё и других людей) на безполезную переписку?" Вы меня хотите в чём-то убедить? За 30 лет в среде Windows мне приходилось и сервера администрировать на чуть более, чем начальном уровне. А вот с Linux я пока дело не имел. Решил попробовать - ОС поставил, OpeHub поставил, MQTT сервер поставил, а вот точку доступа настроить не удалось, хотя теоретически сложного особо ничего и нет. Но не работает, причём, на этапе аутентификации. Профессионалу такие вещи сразу видны, поэтому и обратился за помощью. Поверьте, нет помощи - значит, нет. Терпенье и труд всё перетрут. Edited May 19, 2020 by TarasBY edit
Igor Posted May 19, 2020 Posted May 19, 2020 1 hour ago, TarasBY said: Вы меня хотите в чём-то убедить? No. Just keep this conversation under the general forum terms - don't bump topics.
TarasBY Posted May 20, 2020 Author Posted May 20, 2020 Thank you very much. Chatted. True, I came for another ...
Tido Posted May 20, 2020 Posted May 20, 2020 On 5/12/2020 at 11:45 AM, TarasBY said: I can not raise the Access Point. Maybe it helps to go back to the begin. Create a plan and leave away what is not needed right away, just to see if it works. Like I did here https://forum.armbian.com/topic/3476-bpi-r1-with-new-b53-switch-driver-dsa/?do=findComment&comment=26470
TarasBY Posted May 20, 2020 Author Posted May 20, 2020 2 hours ago, Tido said: Maybe it helps to go back to the begin. Create a plan and leave away what is not needed right away, just to see if it works. Like I did here https://forum.armbian.com/topic/3476-bpi-r1-with-new-b53-switch-driver-dsa/?do=findComment&comment=26470 To be honest, I do not understand the meaning of your actions. I plan to clear all the configuration data and create the AP using software tools (without my participation). But thanks anyway!
Recommended Posts