octal8 Posted December 31, 2023 Share Posted December 31, 2023 (edited) New OPI5+, unable to finish install because ethernet doesn't work. I haven't been able to figure it out and my searches turned up nothing. journalctl has the following messages: - hpptx phy lane locked! - rk_gmac-dwmac fe1c0000.ethernet error: no phy at addr -1 - stmmac_open: cannot attach to phy (error -19) I've checked power supply, cables, edited the interfaces file, and more , with no success. I have an Orange Pi 5 that I can swap as is in its place and everything works. Coupled with the fact that I couldn't find mention of the errors, I'm hoping that someone can help me before I give up and return the OPI5+. Edited December 31, 2023 by octal8 Spelling error. 0 Quote Link to comment Share on other sites More sharing options...
Tony3 Posted December 31, 2023 Share Posted December 31, 2023 Returning and giving up is indeed a simple solution! (the other solution may consist of giving more information about the type of network used, wired? wifi? what wifi card?.....) 1 Quote Link to comment Share on other sites More sharing options...
Werner Posted December 31, 2023 Share Posted December 31, 2023 Providing logs with armbianmonitor -u helps with troubleshooting and significantly raises chances that issue gets addressed. Armbianmonitor -U pastes to console 1 Quote Link to comment Share on other sites More sharing options...
Efe Çetin Posted December 31, 2023 Share Posted December 31, 2023 @octal8 which image did you download 1 Quote Link to comment Share on other sites More sharing options...
Marco Schirrmeister Posted December 31, 2023 Share Posted December 31, 2023 If you used the 6.7.0-rc7 image, then check what overlay and dt file you have configured. This image defaults to the dt file for the original non-plus version. Check and adjust in /boot/armbianEnv.txt the following 2 lines. overlay_prefix=rockchip-rk3588 fdtfile=rockchip/rk3588-orangepi-5-plus.dtb 1 Quote Link to comment Share on other sites More sharing options...
octal8 Posted January 1 Author Share Posted January 1 (edited) I switched to the official Orange Pi installation and it works fine. So it's not a hardware issue. Since an Orange Pi 5 worked fine in the same setup, I was suspecting that and am glad because I didn't want to return it. Based on the symptoms, it seems like a driver/configuration issue. The problem is I don't want to use the official Orange Pi installation since it is run by Huawei with servers in China. For one, I'd much rather use an organization run by volunteers (Armbian) than one run by a corporation. Also, with the way things are going between the USA and China, who knows what may happen in the future with respect to sanctions, etc... Marco, I tried your suggestion and it didn't work. Still no USB3 and Ethernet. Werner, I'm going to try your suggestion next to see if it narrows down what I need to do to make Armbian work. Edited January 1 by octal8 Spelling error. 0 Quote Link to comment Share on other sites More sharing options...
Efe Çetin Posted January 1 Share Posted January 1 I think you use opi5 image instead of opi5+. You have to read description properly 2 Quote Link to comment Share on other sites More sharing options...
octal8 Posted January 1 Author Share Posted January 1 20 minutes ago, Efe Çetin said: I think you use opi5 image instead of opi5+. You have to read description properly On the Armbian website, they only have one image that combines all three hardware versions Orange Pi 5 / 5B / 5 Plus. https://www.armbian.com/orangepi-5/ 0 Quote Link to comment Share on other sites More sharing options...
Efe Çetin Posted January 1 Share Posted January 1 8 minutes ago, octal8 said: On the Armbian website, they only have one image that combines all three hardware versions Orange Pi 5 / 5B / 5 Plus. Check here 1 Quote Link to comment Share on other sites More sharing options...
octal8 Posted January 1 Author Share Posted January 1 2 minutes ago, Efe Çetin said: Check here Thank you, I will. 0 Quote Link to comment Share on other sites More sharing options...
octal8 Posted January 1 Author Share Posted January 1 (edited) Update: -Still no USB3 - Still no Ethernet - Parted doesn't recognize the nvme M.2 card installed. - Installing the OS to the emmc chip remains a mystery. - No sound Edited January 1 by octal8 Added "No sound" 0 Quote Link to comment Share on other sites More sharing options...
Werner Posted January 1 Share Posted January 1 Which image?` 1 Quote Link to comment Share on other sites More sharing options...
Werner Posted January 1 Share Posted January 1 Ethernet works, USB3 works, HDMI works. Did not bother test further https://paste.armbian.com/ruteyebapu 1 Quote Link to comment Share on other sites More sharing options...
octal8 Posted January 1 Author Share Posted January 1 42 minutes ago, Werner said: Which image?` Sorry, I thought I posted that info: Armbian_23.11.1_Orangepi5_bookworm_legacy_5.10.160.img 0 Quote Link to comment Share on other sites More sharing options...
Solution Werner Posted January 1 Solution Share Posted January 1 10 minutes ago, octal8 said: 1_Orangepi5_bookworm_legacy_5 As Efe stated. You are using the wrong images. Oranhe Pi 5 != Orange Pi 5 Plus 1 Quote Link to comment Share on other sites More sharing options...
octal8 Posted January 1 Author Share Posted January 1 8 minutes ago, Werner said: As Efe stated. You are using the wrong images. Oranhe Pi 5 != Orange Pi 5 Plus On the Armbian website, all three OP5 hardware versions are lumped together on the same page. There are two images available on the page, the cli version that I'm using, and a Gnome version. https://www.armbian.com/orangepi-5/ There is also a link for older versions, but since the OPI5+ is new, something tells me they would not be better. What am I missing? 0 Quote Link to comment Share on other sites More sharing options...
octal8 Posted January 1 Author Share Posted January 1 Since I want to use an official Armbian image, I would say that the problem isn't solved until they make one available that works. 0 Quote Link to comment Share on other sites More sharing options...
Werner Posted January 1 Share Posted January 1 30 minutes ago, octal8 said: What am I missing? https://forum.armbian.com/topic/33008-new-install-ethernet-doesnt-work-no-lights-even-and-usb3-ports-are-dead/?do=findComment&comment=178365 1 Quote Link to comment Share on other sites More sharing options...
ricardo_brz Posted January 1 Share Posted January 1 1 hour ago, octal8 said: Since I want to use an official Armbian image The one posted by Efe here is official, do you mean you want something more official than that? 0 Quote Link to comment Share on other sites More sharing options...
octal8 Posted January 1 Author Share Posted January 1 20 minutes ago, ricardo_brz said: The one posted by Efe here is official, do you mean you want something more official than that? My apologies to all, especially Efe. I missed the obvious. I need some sleep. 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.