Jump to content

Bananapi M2 and Gigabit Ethernet


domoticity

Recommended Posts

31 minutes ago, chrisf said:

If the A31s is anything like the gigabit on the A20, it's limited to around 400mbit due to internal bus limitations

 

Nope, for A20 (BananaPi M1) performance see here and for the M2 just search for 'iperf' in this thread there: 

 

'Funny': By searching for M2 iperf results I stumbled accross this here again: https://groups.google.com/d/msg/linux-sunxi/sMMqCjUfoLE/RXYJwz0U_C4J

 

Link to comment
Share on other sites

I just ran iperf3 as server on an XU4

All boards are running at max speed via cpu-freq

Cubietruck

[  4] local 10.0.0.10 port 47340 connected to 10.0.0.17 port 5201
[ ID] Interval           Transfer     Bandwidth       Retr  Cwnd
[  4]   0.00-1.01   sec  64.1 MBytes   534 Mbits/sec    0    264 KBytes
[  4]   1.01-2.00   sec  63.2 MBytes   532 Mbits/sec    0    362 KBytes
[  4]   2.00-3.00   sec  64.0 MBytes   538 Mbits/sec    0    516 KBytes
[  4]   3.00-4.03   sec  62.2 MBytes   508 Mbits/sec    0    690 KBytes
[  4]   4.03-5.02   sec  62.5 MBytes   530 Mbits/sec    0    690 KBytes
[  4]   5.02-6.01   sec  63.6 MBytes   537 Mbits/sec    0    887 KBytes
[  4]   6.01-7.01   sec  52.5 MBytes   442 Mbits/sec    0    990 KBytes
[  4]   7.01-8.02   sec  48.8 MBytes   404 Mbits/sec    0    990 KBytes
[  4]   8.02-9.01   sec  47.5 MBytes   401 Mbits/sec    0    990 KBytes
[  4]   9.01-10.03  sec  48.8 MBytes   404 Mbits/sec    0    990 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bandwidth       Retr
[  4]   0.00-10.03  sec   577 MBytes   483 Mbits/sec    0             sender
[  4]   0.00-10.03  sec   577 MBytes   483 Mbits/sec                  receiver

HC1

[  4] local 10.0.0.18 port 53228 connected to 10.0.0.17 port 5201
[ ID] Interval           Transfer     Bandwidth       Retr  Cwnd
[  4]   0.00-1.00   sec   111 MBytes   935 Mbits/sec    0    417 KBytes
[  4]   1.00-2.00   sec   113 MBytes   944 Mbits/sec    0    417 KBytes
[  4]   2.00-3.00   sec   112 MBytes   941 Mbits/sec    0    417 KBytes
[  4]   3.00-4.00   sec   112 MBytes   941 Mbits/sec    0    437 KBytes
[  4]   4.00-5.00   sec   112 MBytes   943 Mbits/sec    0    437 KBytes
[  4]   5.00-6.00   sec   112 MBytes   941 Mbits/sec    0    437 KBytes
[  4]   6.00-7.00   sec   112 MBytes   940 Mbits/sec    0    437 KBytes
[  4]   7.00-8.00   sec   112 MBytes   940 Mbits/sec    0    437 KBytes
[  4]   8.00-9.00   sec   112 MBytes   940 Mbits/sec    0    437 KBytes
[  4]   9.00-10.00  sec   112 MBytes   942 Mbits/sec    0    437 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bandwidth       Retr
[  4]   0.00-10.00  sec  1.10 GBytes   941 Mbits/sec    0             sender
[  4]   0.00-10.00  sec  1.09 GBytes   940 Mbits/sec                  receiver

What's wrong with my A20 based Cubietruck? It's running Armbian 5.32 with 4.8.4 kernel

 

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.
×
×
  • Create New...

Important Information

Terms of Use - Privacy Policy - Guidelines