All Activity

In pavucontrol, which is the Configuration in Volume Control, set the second Audio to off and exit. After playing the audio and opening the Volume Control at the same time, this problem will not occur and can be adjusted normally My understanding is that two Audio may have output conflict?

Hello, excuse me, can you share the images you have about s812 s805?

I'm half way feeling that it may be possibly to use DS18B20 using gpiod / libgpiod https://git.kernel.org/pub/scm/libs/libgpiod/libgpiod.git/tree/ I tried googling around but thare are lots of offers for DS18B20 many of which use w1-gpio as you are doing the timing requires for DS18B20 fig 16 page 16 https://www.analog.com/media/en/technical-documentation/data-sheets/DS18B20.pdf from 15 uS to 60 uS per bit of data isn't after all that impossible to synchronize the hard part about libgpiod is the timing part as sending and receiving data is timing sensitive, if there is a way to do that to read and write data in sync with tight timing it is possibly feasible to do so even in python. i.e. no kernel drivers, the python (or c etc) codes simply use libgpiod and work the signals. I've thus far not (yet) found one based on libgpiod admist the 'noise' returned from the searches, maybe try searching around and you may find an existing implementation that's already done. ether way, you seemed to have *achieved* making w1-gpio work, perhaps try connecting a sensor to see if the dmesg changes. the hint is [ 4.997833] w1-gpio onewire@0: gpio_request (pin) failed [ 4.997841] w1-gpio: probe of onewire@0 failed with error -22 if w1-gpio does a 'probe' it is probably sending the 'reset' signal to the chip and waiting for a response

Thank you for your answer and suggestions. Hmm, the problem is that I have a DS18B20 sensor connected to OZPIv3, which I used in another project on another SBC. PIN DATA DS18B20 is connected to PC10 and through the 4k7 resistor to VCC 3.3V and the third pin DS18B20 to GND I will have to check this sensor again to see if RPI or OZPIv1 works on the 6.1.x kernel or I will take another unit for testing.

I'm trying to enable GPU support for watching youtube on orange pi 2 zero w model. But there is no Mali driver and even kernel package How can I enable this?

good morning everyone, I installed Armbian 23.02.2 on orangepizero about a year ago without ever having a problem . Today it suddenly stopped booting and I can't get it to start again and that's what I'm interested in, also possibly to recover internal docker configurations. The orangepizero is powered by a 3A power supply under UPS and properly cooled, if I use the latest release on a new SD it works perfectly, so I think it is not a hardware problem. The SD with Armbian 23.02.2 is not corrupted and I can read every part of it. Does anyone know any tricks to get it running again?

Hi all, I have some x905 boxes and I'd like to use one (an old TX95 -> x905w IIRC) as a midi sequencer with fluidsynth. I found the hard way that the default kernel has no midi sequencer support (in kernel or module) so there's no way to use aconnect and have it as a midi box. The only solution seems to be rebuild the kernel with the added module support but it's been decades since last time i rebuilt a kernel and S905 kernels (with added balbes150 mods and stuff to have it working on those cheap boxes) seems a bit too complex for me. So the question is: is there a way to get a working kernel with midi support, and how to put it in. If this wasn't really feasable: how could a mere mortal (with some knowledge) rebuild an x905w kernel, pack it and install without breaking the whole thing in the process ? ( I'm not interested in a GUI or similar, it would work as headless with the RCA out for audio )

Sorry, I don't have a device that supports hdmi audio I tried to use mpg123 to play audio, but as long as the Volume Control is turned on, the bug also appeared I'm still new to audio and video, so I don't know how to solve it

I have remove the armbian-firmware #apt remove armbian-firmware just need to restart it once today. I still trying to find the deb package for older version of armbian-firmware couldn't find it on https://mirror.yandex.ru/mirrors/armbian/archive/orangepione/archive/ for info, I run the board for Pi-Hole using the cloudflared. The second service is a smbd server for low throughput usage in LAN the symtomps after armbian-firmware update to 24.2.1 is a hot cpu, so it might be the system cannot cope with the temperature and just hangs (I do not put any cooling / heatsink for 2 years and its working fine because of the low usages) any suggestion to a armbian-firmware.deb file that i can dpkg is appreciated. thanks

@sakesm Yes i came across that also. Can you confirm that it only happens on analog audio and not on HDMI and when using pulseaudio. I also tested with mpg123 and did not have problems using the mpg123 built in volume controls.

Description The vendor config of rk35xx is originally for rk3588 which doesn't need this driver. But rk3568 need it. CONFIG_NET_VENDOR_MOTORCOMM=y is introduced by rewrite-kernel-config, I guess it should be fine. How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. [x] ./compile.sh BOARD=hinlink-hnas BRANCH=vendor BUILD_DESKTOP=yes BUILD_MINIMAL=yes DEB_COMPRESS=xz KERNEL_CONFIGURE=no RELEASE=jammy KERNEL_GIT=shallow [x] Tested on hinlink hnas which has 4 2.5 inch sata. Checklist: Please delete options that are not relevant. [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [ ] I have commented my code, particularly in hard-to-understand areas [x] My changes generate no new warnings [ ] Any dependent changes have been merged and published in downstream modules View the full article

Why can't the CPU frequency be adjusted in the armbian-config settings?

Hello, everyone I used your patch @Stephen Graf https://github.com/stephengraf/armbian_build_sg/blob/main/patch/kernel/archive/sunxi-6.6/patches.armbian/sound-soc-h616.patch I found a bug when using it. If I turned on Volume Control in the middle of playing video or audio, the video or audio would suddenly speed up playing, even if I just turned on Volume Control without doing anything,very crazy😂

Thanks so much for your help!

Did you try to play a video through HDMI? was sound present? You can use a USB flash (pendrive) to try it. As, I understand, the RK3528 is not working with HDMI audio (in my case neither GPU acceleration for videoplayback, it plays but it's choppy).

rcu: INFO: rcu_sched self-detected stall on CPU rcu: 0-....: (5249 ticks this GP) idle=5ec4/1/0x40000002 softirq=471875/471875 fqs=2602 rcu: (t=5250 jiffies g=738401 q=352 ncpus=4) CPU: 0 PID: 14211 Comm: octoprint Tainted: G C 6.6.16-current-sunxi #1 Hardware name: Allwinner sun8i Family PC is at stmmac_get_stats64+0x24/0x128 LR is at 0xc32bb000 pc : [<c078c5cc>] lr : [<c32bb000>] psr: a0010033 sp : e1fed990 ip : c32b8000 fp : 00000001 r10: 00000000 r9 : c95dee40 r8 : 00000000 r7 : 00000000 r6 : 00000001 r5 : 00000000 r4 : 80000000 r3 : 0093d4a3 r2 : c32bae48 r1 : c50ba6b8 r0 : c32b8000 Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA Thumb Segment none Control: 50c5387d Table: 497a006a DAC: 00000051 stmmac_get_stats64 from dev_get_stats+0x27/0xd0 dev_get_stats from rtnl_fill_stats+0x25/0xb0 rtnl_fill_stats from rtnl_fill_ifinfo+0x4cd/0xde0 rtnl_fill_ifinfo from rtnl_dump_ifinfo+0x1ff/0x49c rtnl_dump_ifinfo from netlink_dump+0xcd/0x270 netlink_dump from __netlink_dump_start+0x15b/0x1ec __netlink_dump_start from rtnetlink_rcv_msg+0x177/0x25c rtnetlink_rcv_msg from netlink_rcv_skb+0x75/0xb0 netlink_rcv_skb from netlink_unicast+0x1c1/0x204 netlink_unicast from netlink_sendmsg+0x185/0x354 netlink_sendmsg from __sock_sendmsg+0x27/0x48 __sock_sendmsg from __sys_sendto+0x7f/0xac __sys_sendto from ret_fast_syscall+0x1/0x5c Exception stack(0xe1fedfa8 to 0xe1fedff0) dfa0: aa039794 0000000c 00000029 aa0397b0 00000014 00000000 dfc0: aa039794 0000000c aa03b920 00000122 00000000 00000029 00000014 00000000 dfe0: 00000122 aa038738 b6dd4325 b6d3db06 Same issue here. I am using Orange pi one. Problem afer installing 6.6.16-current-sunxi Huge utylization of CPU / system freze, I also using, mjpg_streamer, I am metionig about this, because I can only make it working/unfreze only after getting feed from camera on that hardware. I know weird, but it is how it is.

Hi. I would like to know if someone can help me. I was successfully able to compile armbian 6.6.30 with all of @Stephen Graf patches for my orangepi zero 3 having Full Audio working even on HDMI. see below for reference. Now I have a 2nd project. It runs the h616 with 2GB DDR3 RAM with AXP313. Can someone help me with a patch for the AXP313 on h616. Or alternatively, could my h618 orangepi zero 3 setup work if I patch it to run with DDR3? If so where can I find such a patch. Thanks in advance.

main-config.sh: workaround: set the default ARCH to arm64 (replacing armhf) main-config.sh: workaround: set the default ARCH to arm64 (replacing armhf) armhf was disabled for some releases and now we get spurious failures building certain artifacts (firmware) Signed-off-by: Ricardo Pardini ricardo@pardini.net View the full article

based on the messages, it seemed you managed to load the overlay for w1-gpio perhaps venture further and connect a device appropriately ? based on the data sheet https://www.analog.com/media/en/technical-documentation/data-sheets/DS18B20.pdf (page 15, fig 15) it seeemed detection works by master (host) pulling down the line for 480 uS then pull that up again. then the chip would respond by first pulling it down, and after some 60-240 uS pull that up to inform the host of presence. it may take using specialized equipment like a scope / logic analyzer to probe those signals. for what is worth, and not trying to disappoint you, I think it is probably easier to connect the sensor to a (simple) microcontroller e.g. using uart and for the microcontroller to interface the sensor. the thing is for things related to timing, it may take going pretty much close to 'bare metal' e.g. work the on chip hardware to synchronize those signals, e.g. using pwm, spi etc. a h616 manual is found here https://linux-sunxi.org/images/2/24/H616_User_Manual_V1.0_cleaned.pdf if you want to venture there. uart on orange pi zero 3 is likely available in the standard configs without dts overlays.

I read again info https://docs.armbian.com/User-Guide_Allwinner_overlays/ and compile overlay by command: armbian-add-overlay w1-gpio.dts I see that in /boot/overlay-user/ is file w1-gpio.dtbo in /boot/armbianEnv.txt user_overlays=w1-gpio param_w1_pin=PC10 param_w1_pin_int_pullup=1 after this I reboot OZPI v3 after restart OZPIv3 I check dmesg info where found [ 4.990724] Driver for 1-wire Dallas network protocol. [ 4.997793] sun50i-h616-pinctrl 300b000.pinctrl: pin PC10 already requested by onewire@0; cannot claim for 300b000.pinctrl:74 [ 4.997833] w1-gpio onewire@0: gpio_request (pin) failed [ 4.997841] w1-gpio: probe of onewire@0 failed with error -22 cat /sys/kernel/debug/gpio gpiochip0: GPIOs 0-287, parent: platform/300b000.pinctrl, 300b000.pinctrl: gpio-76 ( |red:status ) out lo gpio-77 ( |green:power ) out hi gpio-80 ( |regulator-usb1-vbus ) out hi gpio-166 ( |cd ) in lo ACTIVE LOW gpio-210 ( |reset ) out hi ACTIVE LOW Can anyone help?

on debian distro : sudo nautilus This folder and dtb folder is the same folder it's just an short link

So I been doing some testing and audio through headphone jack "Line Out" works. I added a patch to enable line out in my dts. +&codec { + allwinner,audio-routing = + "Line Out", "LINEOUT"; + status = "okay"; +}; + You need to to enable it using the mixer. (thanks to sasa in the orange pie thread) /usr/bin/amixer -c 0 set 'Left Output Mixer DACL' 100% unmute /usr/bin/amixer -c 0 set 'Left Output Mixer DACR' 100% unmute /usr/bin/amixer -c 0 set 'Right Output Mixer DACL' 100% unmute /usr/bin/amixer -c 0 set 'Right Output Mixer DACR' 100% unmute Bluetooth has a bug where you need to enable bluetooth in android first before it can work with armbian.

Hi, I've tried to blacklist the driver, seemed stable but crashed after 2 weeks. At this point I don't know what else to try. For now i set kernel.panic=10 in /etc/sysctl.d/96-panic.conf to see if at least reboots when a panic happens.

Yes, that i did already. but this machine is supposed to work remotely and if I or for any reason, it reboots, it will never turn ON again if the SD card is not bootable.

Highlighting some of the key changes Collabora worked on with Valve to improve the system update tooling on SteamOS, including the move to Desync, making applying system updates significantly faster and more reliable. View the full article