cam2019 Posted June 8, 2019 Share Posted June 8, 2019 hi guys, literally i'm new to orange pi and as well as here on armbian. like days old. I managed to run and use the usb device in rpi3b+ but was unable to on orange pi. now i know that this is a driver issue. can someone show me how to download and install the driver on my opi pc? TIA Cam Link to comment Share on other sites More sharing options...
Igor Posted June 8, 2019 Share Posted June 8, 2019 1 hour ago, cam2019 said: literally i'm new to orange pi Without logs (armbianmonitor -u) we have absolutely no idea what to tell you. Drivers are usually not just installed but has to be ported to or enabled in the kernel. If you use old kernel 3.4.y forget about ... switch to new one and it will most likely just work. If not ... logs logs logs Link to comment Share on other sites More sharing options...
cam2019 Posted June 8, 2019 Author Share Posted June 8, 2019 pi@orangepipc:~$ sudo ifconfig eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.2.119 netmask 255.255.255.0 broadcast 192.168.2.255 inet6 fe80::e9f5:f619:21ee:d30d prefixlen 64 scopeid 0x20<link> ether 02:81:41:c6:e0:a6 txqueuelen 1000 (Ethernet) RX packets 1790 bytes 157475 (153.7 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 833 bytes 71647 (69.9 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 38 lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 inet6 ::1 prefixlen 128 scopeid 0x10<host> loop txqueuelen 1000 (Local Loopback) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 pi@orangepipc:~$ Spoiler pi@orangepipc:~$ sudo armbianmonitor -U 1 2 ### Activated 1 lzo zram swap devices with 499 MB each 3 4 ### Activated Armbian ramlog partition with zstd compression 5 6 Sat May 4 00:06:23 UTC 2019 | Orange Pi PC | 5.83 | armhf | armv7l | 4.19.38-sunxi 7 8 ### dmesg: 9 10 [ 0.000000] Booting Linux on physical CPU 0x0 11 [ 0.000000] Linux version 4.19.38-sunxi (root@nightly) (gcc version 7.4.1 20181213 [linaro-7.4-2019.02 revision 56ec6f6b99cc167ff0c2f8e1a2eed33 b1edc85d4] (Linaro GCC 7.4-2019.02)) #5.83 SMP Fri May 3 23:33:25 CEST 2019 12 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=50c5387d 13 [ 0.000000] CPU: div instructions available: patching division code 14 [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache 15 [ 0.000000] OF: fdt: Machine model: Xunlong Orange Pi PC 16 [ 0.000000] Memory policy: Data cache writealloc 17 [ 0.000000] cma: Reserved 128 MiB at 0x75c00000 18 [ 0.000000] On node 0 totalpages: 262144 19 [ 0.000000] Normal zone: 1728 pages used for memmap 20 [ 0.000000] Normal zone: 0 pages reserved 21 [ 0.000000] Normal zone: 196608 pages, LIFO batch:63 22 [ 0.000000] HighMem zone: 65536 pages, LIFO batch:15 23 [ 0.000000] psci: probing for conduit method from DT. 24 [ 0.000000] psci: Using PSCI v0.1 Function IDs from DT 25 [ 0.000000] random: get_random_bytes called from start_kernel+0x8d/0x3c6 with crng_init=0 26 [ 0.000000] percpu: Embedded 18 pages/cpu s41548 r8192 d23988 u73728 27 [ 0.000000] pcpu-alloc: s41548 r8192 d23988 u73728 alloc=18*4096 28 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 29 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260416 30 [ 0.000000] Kernel command line: root=UUID=1b49372a-ea5b-42f6-9e60-036606066891 rootwait rootfstype=ext4 console=ttyS0,115200 console=tty1 hdmi .audio=EDID:0 disp.screen0_output_mode=1920x1080p60 panic=10 consoleblank=0 loglevel=1 ubootpart=5ae5405d-01 ubootsource=mmc usb-storage.quirks= sunxi_v e_mem_reserve=0 sunxi_g2d_mem_reserve=0 sunxi_fb_mem_reserve=16 cgroup_enable=memory swapaccount=1 31 [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) 32 [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) 33 [ 0.000000] allocated 1048576 bytes of page_ext 34 [ 0.000000] Memory: 886136K/1048576K available (9216K kernel code, 1004K rwdata, 2576K rodata, 1024K init, 331K bss, 31368K reserved, 131072K c ma-reserved, 131060K highmem) 35 [ 0.000000] Virtual kernel memory layout: 36 vector : 0xffff0000 - 0xffff1000 ( 4 kB) 37 fixmap : 0xffc00000 - 0xfff00000 (3072 kB) 38 vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) 39 lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) 40 pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) 41 modules : 0xbf800000 - 0xbfe00000 ( 6 MB) 42 .text : 0x(ptrval) - 0x(ptrval) (10208 kB) 43 .init : 0x(ptrval) - 0x(ptrval) (1024 kB) 44 .data : 0x(ptrval) - 0x(ptrval) (1005 kB) 45 .bss : 0x(ptrval) - 0x(ptrval) ( 332 kB) 46 [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 47 [ 0.000000] ftrace: allocating 39959 entries in 79 pages 48 [ 0.000000] rcu: Hierarchical RCU implementation. 49 [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. 50 [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 51 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 52 [ 0.000000] GIC: Using split EOI/Deactivate mode 53 [ 0.000000] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns 54 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). 55 [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns 56 [ 0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns 57 [ 0.000013] Switching to timer-based delay loop, resolution 41ns 58 [ 0.000169] Console: colour dummy device 80x30 59 [ 0.000181] console [tty1] enabled 60 [ 0.000229] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) 61 [ 0.000239] pid_max: default: 32768 minimum: 301 62 [ 0.000432] Security Framework initialized 63 [ 0.000442] AppArmor: AppArmor disabled by boot time parameter 64 [ 0.000513] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) 65 [ 0.000523] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) 66 [ 0.001348] CPU: Testing write buffer coherency: ok 67 [ 0.001761] CPU0: update cpu_capacity 1024 68 [ 0.001768] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 69 [ 0.002245] Setting up static identity map for 0x40100000 - 0x40100054 70 [ 0.002385] rcu: Hierarchical SRCU implementation. 71 [ 0.003095] smp: Bringing up secondary CPUs ... 72 [ 0.013784] CPU1: update cpu_capacity 1024 73 [ 0.013789] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 74 [ 0.024567] CPU2: update cpu_capacity 1024 75 [ 0.024573] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 76 [ 0.035283] CPU3: update cpu_capacity 1024 77 [ 0.035289] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 78 [ 0.035381] smp: Brought up 1 node, 4 CPUs 79 [ 0.035388] SMP: Total of 4 processors activated (192.00 BogoMIPS). 80 [ 0.035392] CPU: All CPU(s) started in HYP mode. 81 [ 0.035394] CPU: Virtualization extensions available. 82 [ 0.036535] devtmpfs: initialized 83 [ 0.043004] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 84 [ 0.043255] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns 85 [ 0.043271] futex hash table entries: 1024 (order: 4, 65536 bytes) 86 [ 0.047939] xor: measuring software checksum speed 87 [ 0.087243] arm4regs : 1255.000 MB/sec 88 [ 0.127299] 8regs : 748.000 MB/sec 89 [ 0.167359] 32regs : 766.000 MB/sec 90 [ 0.207420] neon : 1270.000 MB/sec 91 [ 0.207424] xor: using function: neon (1270.000 MB/sec) 92 [ 0.207489] pinctrl core: initialized pinctrl subsystem 93 [ 0.208390] NET: Registered protocol family 16 94 [ 0.210766] DMA: preallocated 2048 KiB pool for atomic coherent allocations 95 [ 0.211237] audit: initializing netlink subsys (disabled) 96 [ 0.211401] audit: type=2000 audit(0.184:1): state=initialized audit_enabled=0 res=1 97 [ 0.211925] cpuidle: using governor ladder 98 [ 0.211954] cpuidle: using governor menu 99 [ 0.212466] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. 100 [ 0.212471] hw-breakpoint: maximum watchpoint size is 8 bytes. 101 [ 0.295938] raid6: int32x1 gen() 189 MB/s 102 [ 0.363856] raid6: int32x1 xor() 160 MB/s 103 [ 0.431884] raid6: int32x2 gen() 255 MB/s 104 [ 0.499955] raid6: int32x2 xor() 194 MB/s 105 [ 0.568096] raid6: int32x4 gen() 258 MB/s 106 [ 0.636214] raid6: int32x4 xor() 193 MB/s 107 [ 0.704224] raid6: int32x8 gen() 247 MB/s 108 [ 0.772453] raid6: int32x8 xor() 172 MB/s 109 [ 0.840488] raid6: neonx1 gen() 495 MB/s 110 [ 0.908535] raid6: neonx1 xor() 460 MB/s 111 [ 0.976677] raid6: neonx2 gen() 664 MB/s 112 [ 1.044741] raid6: neonx2 xor() 594 MB/s 113 [ 1.112874] raid6: neonx4 gen() 798 MB/s 114 [ 1.180931] raid6: neonx4 xor() 669 MB/s 115 [ 1.249026] raid6: neonx8 gen() 716 MB/s 116 [ 1.317138] raid6: neonx8 xor() 606 MB/s 117 [ 1.317142] raid6: using algorithm neonx4 gen() 798 MB/s 118 [ 1.317145] raid6: .... xor() 669 MB/s, rmw enabled 119 [ 1.317148] raid6: using neon recovery algorithm 120 [ 1.318505] SCSI subsystem initialized 121 [ 1.318692] libata version 3.00 loaded. 122 [ 1.318884] usbcore: registered new interface driver usbfs 123 [ 1.318922] usbcore: registered new interface driver hub 124 [ 1.318992] usbcore: registered new device driver usb 125 [ 1.319161] media: Linux media interface: v0.10 126 [ 1.319189] videodev: Linux video capture interface: v2.00 127 [ 1.319301] pps_core: LinuxPPS API ver. 1 registered 128 [ 1.319305] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> 129 [ 1.319320] PTP clock support registered 130 [ 1.320892] clocksource: Switched to clocksource arch_sys_counter 131 [ 1.423959] VFS: Disk quotas dquot_6.6.0 132 [ 1.424035] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) 133 [ 1.431586] NET: Registered protocol family 2 134 [ 1.432234] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) 135 [ 1.432260] TCP established hash table entries: 8192 (order: 3, 32768 bytes) 136 [ 1.432344] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) 137 [ 1.432455] TCP: Hash tables configured (established 8192 bind 8192) 138 [ 1.432562] UDP hash table entries: 512 (order: 2, 16384 bytes) 139 [ 1.432618] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) 140 [ 1.432816] NET: Registered protocol family 1 141 [ 1.433363] RPC: Registered named UNIX socket transport module. 142 [ 1.433367] RPC: Registered udp transport module. 143 [ 1.433370] RPC: Registered tcp transport module. 144 [ 1.433373] RPC: Registered tcp NFSv4.1 backchannel transport module. 145 [ 1.433625] Trying to unpack rootfs image as initramfs... 146 [ 1.732552] Freeing initrd memory: 4816K 147 [ 1.734337] Initialise system trusted keyrings 148 [ 1.734537] workingset: timestamp_bits=14 max_order=18 bucket_order=4 149 [ 1.740137] zbud: loaded 150 [ 1.742296] NFS: Registering the id_resolver key type 151 [ 1.742331] Key type id_resolver registered 152 [ 1.742335] Key type id_legacy registered 153 [ 1.742346] nfs4filelayout_init: NFSv4 File Layout Driver Registering... 154 [ 1.742351] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). 155 [ 1.743421] JFS: nTxBlock = 7984, nTxLock = 63876 156 [ 1.752167] SGI XFS with ACLs, security attributes, realtime, no debug enabled 157 [ 1.759829] Key type asymmetric registered 158 [ 1.759838] Asymmetric key parser 'x509' registered 159 [ 1.759910] bounce: pool size: 64 pages 160 [ 1.759984] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) 161 [ 1.760137] io scheduler noop registered 162 [ 1.760142] io scheduler deadline registered 163 [ 1.760337] io scheduler cfq registered (default) 164 [ 1.760342] io scheduler mq-deadline registered 165 [ 1.760346] io scheduler kyber registered 166 [ 1.760474] io scheduler bfq registered 167 [ 1.761630] sun4i-usb-phy 1c19400.phy: Couldn't request ID GPIO 168 [ 1.765612] sun8i-h3-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver 169 [ 1.767127] sun8i-h3-r-pinctrl 1f02c00.pinctrl: initialized sunXi PIO driver 170 [ 1.815538] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled 171 [ 1.817761] console [ttyS0] disabled 172 [ 1.837922] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 42, base_baud = 1500000) is a U6_16550A 173 [ 1.837976] console [ttyS0] enabled 174 [ 1.861323] sun4i-drm display-engine: bound 1100000.mixer (ops 0xc0a85d08) 175 [ 1.861572] sun4i-drm display-engine: bound 1c0c000.lcd-controller (ops 0xc0a83454) 176 [ 1.861625] sun8i-dw-hdmi 1ee0000.hdmi: 1ee0000.hdmi supply hvcc not found, using dummy regulator 177 [ 1.861681] sun8i-dw-hdmi 1ee0000.hdmi: Linked as a consumer to regulator.0 178 [ 1.862482] sun8i-dw-hdmi 1ee0000.hdmi: Detected HDMI TX controller v1.32a with HDCP (sun8i_dw_hdmi_phy) 179 [ 1.862826] sun8i-dw-hdmi 1ee0000.hdmi: registered DesignWare HDMI I2C bus driver 180 [ 1.863068] sun4i-drm display-engine: bound 1ee0000.hdmi (ops 0xc0a8578c) 181 [ 1.863074] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). 182 [ 1.863077] [drm] No driver support for vblank timestamp query. 183 [ 1.863129] [drm] Cannot find any crtc or sizes 184 [ 1.863554] [drm] Initialized sun4i-drm 1.0.0 20150629 for display-engine on minor 0 185 [ 1.866397] brd: module loaded 186 [ 1.871727] loop: module loaded 187 [ 1.873978] libphy: Fixed MDIO Bus: probed 188 [ 1.874506] dwmac-sun8i 1c30000.ethernet: PTP uses main clock 189 [ 1.874556] dwmac-sun8i 1c30000.ethernet: No regulator found 190 [ 1.874861] dwmac-sun8i 1c30000.ethernet: Current syscon value is not the default 148000 (expect 58000) 191 [ 1.874878] dwmac-sun8i 1c30000.ethernet: No HW DMA feature register supported 192 [ 1.874884] dwmac-sun8i 1c30000.ethernet: RX Checksum Offload Engine supported 193 [ 1.874890] dwmac-sun8i 1c30000.ethernet: COE Type 2 194 [ 1.874896] dwmac-sun8i 1c30000.ethernet: TX Checksum insertion supported 195 [ 1.874901] dwmac-sun8i 1c30000.ethernet: Normal descriptors 196 [ 1.874906] dwmac-sun8i 1c30000.ethernet: Chain mode enabled 197 [ 1.875039] libphy: stmmac: probed 198 [ 1.875474] dwmac-sun8i 1c30000.ethernet: Found internal PHY node 199 [ 1.875570] libphy: mdio_mux: probed 200 [ 1.875588] dwmac-sun8i 1c30000.ethernet: Switch mux to internal PHY 201 [ 1.875594] dwmac-sun8i 1c30000.ethernet: Powering internal PHY 202 [ 1.880329] libphy: mdio_mux: probed 203 [ 1.881288] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver 204 [ 1.881293] ehci-platform: EHCI generic platform driver 205 [ 1.881466] ehci-platform 1c1a000.usb: EHCI Host Controller 206 [ 1.881492] ehci-platform 1c1a000.usb: new USB bus registered, assigned bus number 1 207 [ 1.882237] ehci-platform 1c1a000.usb: irq 26, io mem 0x01c1a000 208 [ 1.896906] ehci-platform 1c1a000.usb: USB 2.0 started, EHCI 1.00 209 [ 1.897175] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 210 [ 1.897183] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 211 [ 1.897189] usb usb1: Product: EHCI Host Controller 212 [ 1.897194] usb usb1: Manufacturer: Linux 4.19.38-sunxi ehci_hcd 213 [ 1.897199] usb usb1: SerialNumber: 1c1a000.usb 214 [ 1.897756] hub 1-0:1.0: USB hub found 215 [ 1.897807] hub 1-0:1.0: 1 port detected 216 [ 1.898646] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver 217 [ 1.898671] ohci-platform: OHCI generic platform driver 218 [ 1.898820] ohci-platform 1c1a400.usb: Generic Platform OHCI controller 219 [ 1.898840] ohci-platform 1c1a400.usb: new USB bus registered, assigned bus number 2 220 [ 1.898999] ohci-platform 1c1a400.usb: irq 27, io mem 0x01c1a400 221 [ 1.961130] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19 222 [ 1.961137] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 223 [ 1.961143] usb usb2: Product: Generic Platform OHCI controller 224 [ 1.961148] usb usb2: Manufacturer: Linux 4.19.38-sunxi ohci_hcd 225 [ 1.961153] usb usb2: SerialNumber: 1c1a400.usb 226 [ 1.961601] hub 2-0:1.0: USB hub found 227 [ 1.961643] hub 2-0:1.0: 1 port detected 228 [ 1.962794] usbcore: registered new interface driver usb-storage 229 [ 1.963502] sun6i-rtc 1f00000.rtc: rtc core: registered rtc-sun6i as rtc0 230 [ 1.963508] sun6i-rtc 1f00000.rtc: RTC enabled 231 [ 1.963707] i2c /dev entries driver 232 [ 1.965681] sunxi-wdt 1c20ca0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) 233 [ 1.966399] sunxi-mmc 1c0f000.mmc: Linked as a consumer to regulator.2 234 [ 1.966866] sunxi-mmc 1c0f000.mmc: Got CD GPIO 235 [ 1.967052] ledtrig-cpu: registered to indicate activity on CPUs 236 [ 1.967131] hidraw: raw HID events driver (C) Jiri Kosina 237 [ 1.967245] usbcore: registered new interface driver usbhid 238 [ 1.967248] usbhid: USB HID core driver 239 [ 1.973470] Initializing XFRM netlink socket 240 [ 1.974103] NET: Registered protocol family 10 241 [ 1.988831] Segment Routing with IPv6 242 [ 1.988966] NET: Registered protocol family 17 243 [ 1.988992] NET: Registered protocol family 15 244 [ 1.989051] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this . 245 [ 1.989096] 8021q: 802.1Q VLAN Support v1.8 246 [ 1.989378] Key type dns_resolver registered 247 [ 1.989813] Registering SWP/SWPB emulation handler 248 [ 1.990411] registered taskstats version 1 249 [ 1.990416] Loading compiled-in X.509 certificates 250 [ 1.990499] zswap: loaded using pool lzo/zbud 251 [ 1.992200] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB 252 [ 1.992289] Btrfs loaded, crc32c=crc32c-generic 253 [ 1.999248] Key type encrypted registered 254 [ 2.008032] sun4i-usb-phy 1c19400.phy: Linked as a consumer to regulator.4 255 [ 2.009007] ehci-platform 1c1b000.usb: EHCI Host Controller 256 [ 2.009035] ehci-platform 1c1b000.usb: new USB bus registered, assigned bus number 3 257 [ 2.009561] ehci-platform 1c1b000.usb: irq 28, io mem 0x01c1b000 258 [ 2.024931] ehci-platform 1c1b000.usb: USB 2.0 started, EHCI 1.00 259 [ 2.025152] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 260 [ 2.025160] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 261 [ 2.025166] usb usb3: Product: EHCI Host Controller 262 [ 2.025171] usb usb3: Manufacturer: Linux 4.19.38-sunxi ehci_hcd 263 [ 2.025177] usb usb3: SerialNumber: 1c1b000.usb 264 [ 2.025687] hub 3-0:1.0: USB hub found 265 [ 2.025724] hub 3-0:1.0: 1 port detected 266 [ 2.026478] ehci-platform 1c1c000.usb: EHCI Host Controller 267 [ 2.026499] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 4 268 [ 2.026717] ehci-platform 1c1c000.usb: irq 30, io mem 0x01c1c000 269 [ 2.028934] mmc0: host does not support reading read-only switch, assuming write-enable 270 [ 2.031932] mmc0: new high speed SDHC card at address aaaa 271 [ 2.033191] mmcblk0: mmc0:aaaa SL16G 14.8 GiB 272 [ 2.035705] mmcblk0: p1 273 [ 2.040907] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 274 [ 2.041121] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 275 [ 2.041129] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 276 [ 2.041134] usb usb4: Product: EHCI Host Controller 277 [ 2.041140] usb usb4: Manufacturer: Linux 4.19.38-sunxi ehci_hcd 278 [ 2.041145] usb usb4: SerialNumber: 1c1c000.usb 279 [ 2.041610] hub 4-0:1.0: USB hub found 280 [ 2.041649] hub 4-0:1.0: 1 port detected 281 [ 2.042496] ehci-platform 1c1d000.usb: EHCI Host Controller 282 [ 2.042521] ehci-platform 1c1d000.usb: new USB bus registered, assigned bus number 5 283 [ 2.042851] ehci-platform 1c1d000.usb: irq 32, io mem 0x01c1d000 284 [ 2.056895] ehci-platform 1c1d000.usb: USB 2.0 started, EHCI 1.00 285 [ 2.057078] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 286 [ 2.057085] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 287 [ 2.057091] usb usb5: Product: EHCI Host Controller 288 [ 2.057096] usb usb5: Manufacturer: Linux 4.19.38-sunxi ehci_hcd 289 [ 2.057101] usb usb5: SerialNumber: 1c1d000.usb 290 [ 2.057555] hub 5-0:1.0: USB hub found 291 [ 2.057591] hub 5-0:1.0: 1 port detected 292 [ 2.058305] ohci-platform 1c1b400.usb: Generic Platform OHCI controller 293 [ 2.058326] ohci-platform 1c1b400.usb: new USB bus registered, assigned bus number 6 294 [ 2.058496] ohci-platform 1c1b400.usb: irq 29, io mem 0x01c1b400 295 [ 2.121076] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19 296 [ 2.121084] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 297 [ 2.121089] usb usb6: Product: Generic Platform OHCI controller 298 [ 2.121095] usb usb6: Manufacturer: Linux 4.19.38-sunxi ohci_hcd 299 [ 2.121100] usb usb6: SerialNumber: 1c1b400.usb 300 [ 2.121558] hub 6-0:1.0: USB hub found 301 [ 2.121591] hub 6-0:1.0: 1 port detected 302 [ 2.122279] ohci-platform 1c1c400.usb: Generic Platform OHCI controller 303 [ 2.122301] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 7 304 [ 2.122452] ohci-platform 1c1c400.usb: irq 31, io mem 0x01c1c400 305 [ 2.185077] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19 306 [ 2.185085] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 307 [ 2.185090] usb usb7: Product: Generic Platform OHCI controller 308 [ 2.185096] usb usb7: Manufacturer: Linux 4.19.38-sunxi ohci_hcd 309 [ 2.185101] usb usb7: SerialNumber: 1c1c400.usb 310 [ 2.185532] hub 7-0:1.0: USB hub found 311 [ 2.185566] hub 7-0:1.0: 1 port detected 312 [ 2.186228] ohci-platform 1c1d400.usb: Generic Platform OHCI controller 313 [ 2.186260] ohci-platform 1c1d400.usb: new USB bus registered, assigned bus number 8 314 [ 2.186417] ohci-platform 1c1d400.usb: irq 33, io mem 0x01c1d400 315 [ 2.249097] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19 316 [ 2.249105] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1 317 [ 2.249110] usb usb8: Product: Generic Platform OHCI controller 318 [ 2.249116] usb usb8: Manufacturer: Linux 4.19.38-sunxi ohci_hcd 319 [ 2.249121] usb usb8: SerialNumber: 1c1d400.usb 320 [ 2.249657] hub 8-0:1.0: USB hub found 321 [ 2.249692] hub 8-0:1.0: 1 port detected 322 [ 2.250431] usb_phy_generic usb_phy_generic.2.auto: usb_phy_generic.2.auto supply vcc not found, using dummy regulator 323 [ 2.250531] usb_phy_generic usb_phy_generic.2.auto: Linked as a consumer to regulator.0 324 [ 2.250820] musb-hdrc musb-hdrc.3.auto: MUSB HDRC host driver 325 [ 2.250830] musb-hdrc musb-hdrc.3.auto: new USB bus registered, assigned bus number 9 326 [ 2.251057] usb usb9: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 327 [ 2.251065] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1 328 [ 2.251071] usb usb9: Product: MUSB HDRC host driver 329 [ 2.251076] usb usb9: Manufacturer: Linux 4.19.38-sunxi musb-hcd 330 [ 2.251081] usb usb9: SerialNumber: musb-hdrc.3.auto 331 [ 2.251529] hub 9-0:1.0: USB hub found 332 [ 2.251569] hub 9-0:1.0: 1 port detected 333 [ 2.252474] sun6i-rtc 1f00000.rtc: setting system clock to 1970-01-01 00:00:13 UTC (13) 334 [ 2.252661] of_cfs_init 335 [ 2.252744] of_cfs_init: OK 336 [ 2.252930] vcc3v0: disabling 337 [ 2.252938] vcc5v0: disabling 338 [ 2.252942] usb0-vbus: disabling 339 [ 2.256208] Freeing unused kernel memory: 1024K 340 [ 2.273085] Run /init as init process 341 [ 2.318941] random: systemd-udevd: uninitialized urandom read (16 bytes read) 342 [ 2.319462] random: systemd-udevd: uninitialized urandom read (16 bytes read) 343 [ 2.319562] random: systemd-udevd: uninitialized urandom read (16 bytes read) 344 [ 2.376930] usb 4-1: new high-speed USB device number 2 using ehci-platform 345 [ 2.534395] usb 4-1: New USB device found, idVendor=0bda, idProduct=8153, bcdDevice=30.00 346 [ 2.534406] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=6 347 [ 2.534412] usb 4-1: Product: USB 10/100/1000 LAN 348 [ 2.534417] usb 4-1: Manufacturer: Realtek 349 [ 2.534423] usb 4-1: SerialNumber: 000001 350 [ 2.688958] usb 6-1: new full-speed USB device number 2 using ohci-platform 351 [ 2.877180] [drm] Cannot find any crtc or sizes 352 [ 2.916010] usb 6-1: New USB device found, idVendor=25a7, idProduct=fa61, bcdDevice= 6.17 353 [ 2.916021] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 354 [ 2.916027] usb 6-1: Product: 2.4G Receiver 355 [ 2.916032] usb 6-1: Manufacturer: Compx 356 [ 2.924030] input: Compx 2.4G Receiver as /devices/platform/soc/1c1b400.usb/usb6/6-1/6-1:1.0/0003:25A7:FA61.0001/input/input0 357 [ 2.981190] hid-generic 0003:25A7:FA61.0001: input,hidraw0: USB HID v1.10 Keyboard [Compx 2.4G Receiver] on usb-1c1b400.usb-1/input0 358 [ 2.989799] input: Compx 2.4G Receiver Mouse as /devices/platform/soc/1c1b400.usb/usb6/6-1/6-1:1.1/0003:25A7:FA61.0002/input/input1 359 [ 2.989945] input: Compx 2.4G Receiver as /devices/platform/soc/1c1b400.usb/usb6/6-1/6-1:1.1/0003:25A7:FA61.0002/input/input2 360 [ 2.990158] input: Compx 2.4G Receiver Consumer Control as /devices/platform/soc/1c1b400.usb/usb6/6-1/6-1:1.1/0003:25A7:FA61.0002/input/input3 361 [ 3.049147] input: Compx 2.4G Receiver System Control as /devices/platform/soc/1c1b400.usb/usb6/6-1/6-1:1.1/0003:25A7:FA61.0002/input/input4 362 [ 3.049598] hid-generic 0003:25A7:FA61.0002: input,hiddev96,hidraw1: USB HID v1.10 Mouse [Compx 2.4G Receiver] on usb-1c1b400.usb-1/input1 363 [ 3.511363] random: fast init done 364 [ 3.615934] EXT4-fs (mmcblk0p1): mounted filesystem with writeback data mode. Opts: (null) 365 [ 4.078727] systemd[1]: System time before build time, advancing clock. 366 [ 4.125041] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN) 367 [ 4.125529] systemd[1]: Detected architecture arm. 368 [ 4.130016] systemd[1]: Set hostname to <orangepipc>. 369 [ 4.478021] systemd[1]: Listening on udev Control Socket. 370 [ 4.478848] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. 371 [ 4.479894] systemd[1]: Created slice User and Session Slice. 372 [ 4.480225] systemd[1]: Reached target Remote File Systems. 373 [ 4.480572] systemd[1]: Listening on udev Kernel Socket. 374 [ 4.481122] systemd[1]: Listening on Journal Socket. 375 [ 4.481733] systemd[1]: Listening on Journal Audit Socket. 376 [ 4.586404] EXT4-fs (mmcblk0p1): re-mounted. Opts: commit=600,errors=remount-ro 377 [ 4.887288] systemd-journald[226]: Received request to flush runtime journal from PID 1 378 [ 5.326573] input: r_gpio_keys as /devices/platform/r_gpio_keys/input/input6 379 [ 5.328115] cpu cpu0: Linked as a consumer to regulator.5 380 [ 5.328200] cpu cpu0: Dropping the link to regulator.5 381 [ 5.328402] cpu cpu0: Linked as a consumer to regulator.5 382 [ 5.515474] sun8i_ths 1c25000.thermal-sensor: no memory resources defined 383 [ 5.515499] sun8i_ths: probe of 1c25000.thermal-sensor failed with error -22 384 [ 5.568003] Registered IR keymap rc-empty 385 [ 5.568112] rc rc0: sunxi-ir as /devices/platform/soc/1f02000.ir/rc/rc0 386 [ 5.568236] input: sunxi-ir as /devices/platform/soc/1f02000.ir/rc/rc0/input7 387 [ 5.570304] rc rc0: lirc_dev: driver sunxi-ir registered at minor = 0, raw IR receiver, no transmitter 388 [ 5.571663] usbcore: registered new interface driver r8152 389 [ 5.581807] thermal thermal_zone0: failed to read out thermal zone (-110) 390 [ 5.582519] sunxi-ir 1f02000.ir: initialized sunXi IR driver 391 [ 5.583383] zram: Added device: zram0 392 [ 5.584033] zram: Added device: zram1 393 [ 5.584637] zram: Added device: zram2 394 [ 5.594086] usbcore: registered new interface driver cdc_ether 395 [ 5.622079] lima 1c40000.gpu: bus rate = 200000000 396 [ 5.622093] lima 1c40000.gpu: mod rate = 384000000 397 [ 5.630191] sun4i-codec 1c22c00.codec: ASoC: codec-analog@1f015c0 not registered 398 [ 5.630203] sun4i-codec 1c22c00.codec: Failed to register our card 399 [ 5.631142] [TTM] Zone kernel: Available graphics memory: 380458 kiB 400 [ 5.631152] [TTM] Zone highmem: Available graphics memory: 511524 kiB 401 [ 5.631156] [TTM] Initializing pool allocator 402 [ 5.631991] lima 1c40000.gpu: gp - mali400 version major 1 minor 1 403 [ 5.632053] lima 1c40000.gpu: pp0 - mali400 version major 1 minor 1 404 [ 5.632096] lima 1c40000.gpu: pp1 - mali400 version major 1 minor 1 405 [ 5.632130] lima 1c40000.gpu: l2 cache 64K, 4-way, 64byte cache line, 64bit external bus 406 [ 5.642626] sun4i-codec 1c22c00.codec: ASoC: Failed to create component debugfs directory 407 [ 5.647290] sun4i-codec 1c22c00.codec: Codec <-> 1c22c00.codec mapping ok 408 [ 5.660651] [drm] Initialized lima 1.0.0 20170325 for 1c40000.gpu on minor 1 409 [ 5.673708] zram1: detected capacity change from 0 to 523800576 410 [ 5.709082] usb 4-1: reset high-speed USB device number 2 using ehci-platform 411 [ 5.747486] Adding 511520k swap on /dev/zram1. Priority:5 extents:1 across:511520k SSFS 412 [ 5.884641] zram0: detected capacity change from 0 to 52428800 413 [ 5.906764] r8152 4-1:1.0 eth1: v1.09.9 414 [ 6.188868] EXT4-fs (zram0): mounted filesystem without journal. Opts: discard 415 [ 6.552250] r8152 4-1:1.0 enx00e04c680046: renamed from eth1 416 [ 6.910650] random: crng init done 417 [ 6.910664] random: 7 urandom warning(s) missed due to ratelimiting 418 419 ### armbian-release: 420 421 # PLEASE DO NOT EDIT THIS FILE 422 BOARD=orangepipc 423 BOARD_NAME="Orange Pi PC" 424 BOARDFAMILY=sun8i 425 VERSION=5.83 426 LINUXFAMILY=sunxi 427 BRANCH=next 428 ARCH=arm 429 IMAGE_TYPE=stable 430 BOARD_TYPE=conf 431 INITRD_ARCH=arm 432 KERNEL_IMAGE_TYPE=zImage 433 434 ### boot environment: 435 436 verbosity=1 437 logo=disabled 438 console=both 439 disp_mode=1920x1080p60 440 overlay_prefix=sun8i-h3 441 rootdev=UUID=1b49372a-ea5b-42f6-9e60-036606066891 442 rootfstype=ext4 443 444 ### lsusb: 445 446 Sat May 4 00:06:23 UTC 2019 | Orange Pi PC | 5.83 | armhf | armv7l | 4.19.38-sunxi 447 448 ### [resize2fs] Leaving 1 percent spare area. Start resizing partition /dev/mmcblk0p1 now: 449 450 major minor #blocks name 451 452 1 0 4096 ram0 453 1 1 4096 ram1 454 1 2 4096 ram2 455 1 3 4096 ram3 456 179 0 15558144 mmcblk0 457 179 1 1077248 mmcblk0p1 458 254 0 51200 zram0 459 254 1 511524 zram1 460 461 Executing fdisk, fsck and partprobe: 462 463 Welcome to fdisk (util-linux 2.29.2). 464 Changes will remain in memory only, until you decide to write them. 465 Be careful before using the write command. 466 467 468 Command (m for help): Selected partition 1 469 Partition 1 has been deleted. 470 471 Command (m for help): Partition type 472 p primary (0 primary, 0 extended, 4 free) 473 e extended (container for logical partitions) 474 Select (default p): Partition number (1-4, default 1): First sector (2048-31116287, default 2048): Last sector, +sectors or +size{K,M,G,T,P} (8192 -31116287, default 31116287): 475 Created a new partition 1 of type 'Linux' and of size 14.7 GiB. 476 Partition #1 contains a ext4 signature. 477 478 Command (m for help): 479 The partition table has been altered. 480 Calling ioctl() to re-read partition table. 481 Re-reading the partition table failed.: Device or resource busy 482 483 The kernel still uses the old table. The new table will be used at the next reboot or after you run partprobe(8) or kpartx(8). 484 485 Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub 486 Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub 487 Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub 488 Bus 004 Device 002: ID 0bda:8153 Realtek Semiconductor Corp. 489 Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub 490 Bus 006 Device 002: ID 25a7:fa61 491 Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub 492 Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub 493 Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub 494 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub 495 Bus 009 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub 496 497 ### lscpu: 498 499 New partition table: 500 501 Architecture: armv7l 502 Byte Order: Little Endian 503 CPU(s): 4 504 On-line CPU(s) list: 0-3 505 Thread(s) per core: 1 506 Core(s) per socket: 4 507 Socket(s): 1 508 Model: 5 509 Model name: ARMv7 Processor rev 5 (v7l) 510 CPU max MHz: 1368.0000 511 CPU min MHz: 120.0000 512 BogoMIPS: 65.14 513 Flags: half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm 514 515 ### cpuinfo: 516 517 major minor #blocks name 518 519 1 0 4096 ram0 520 1 1 4096 ram1 521 1 2 4096 ram2 522 1 3 4096 ram3 523 179 0 15558144 mmcblk0 524 179 1 15398464 mmcblk0p1 525 254 0 51200 zram0 526 254 1 511524 zram1 527 528 Now trying to resize ext4 filesystem on /dev/mmcblk0p1 to the limits: 529 530 processor : 0 531 model name : ARMv7 Processor rev 5 (v7l) 532 BogoMIPS : 65.14 533 Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm 534 CPU implementer : 0x41 535 CPU architecture: 7 536 CPU variant : 0x0 537 CPU part : 0xc07 538 CPU revision : 5 539 540 processor : 1 541 model name : ARMv7 Processor rev 5 (v7l) 542 BogoMIPS : 65.14 543 Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm 544 CPU implementer : 0x41 545 CPU architecture: 7 546 CPU variant : 0x0 547 CPU part : 0xc07 548 CPU revision : 5 549 550 processor : 2 551 model name : ARMv7 Processor rev 5 (v7l) 552 BogoMIPS : 65.14 553 Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm 554 CPU implementer : 0x41 555 CPU architecture: 7 556 CPU variant : 0x0 557 CPU part : 0xc07 558 CPU revision : 5 559 560 processor : 3 561 model name : ARMv7 Processor rev 5 (v7l) 562 BogoMIPS : 65.14 563 Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm 564 CPU implementer : 0x41 565 CPU architecture: 7 566 CPU variant : 0x0 567 CPU part : 0xc07 568 CPU revision : 5 569 570 Hardware : Allwinner sun8i Family 571 Revision : 0000 572 Serial : 02c0008141c6e0a6 573 574 ### meminfo: 575 576 MemTotal: 1023048 kB 577 MemFree: 927044 kB 578 MemAvailable: 947340 kB 579 Buffers: 6116 kB 580 Cached: 25540 kB 581 SwapCached: 0 kB 582 Active: 26692 kB 583 Inactive: 13076 kB 584 Active(anon): 8052 kB 585 Inactive(anon): 3856 kB 586 Active(file): 18640 kB 587 Inactive(file): 9220 kB 588 Unevictable: 0 kB 589 Mlocked: 0 kB 590 HighTotal: 262132 kB 591 HighFree: 211180 kB 592 LowTotal: 760916 kB 593 LowFree: 715864 kB 594 SwapTotal: 511520 kB 595 SwapFree: 511520 kB 596 Dirty: 0 kB 597 Writeback: 12 kB 598 AnonPages: 7912 kB 599 Mapped: 7200 kB 600 Shmem: 4000 kB 601 Slab: 24132 kB 602 SReclaimable: 11496 kB 603 SUnreclaim: 12636 kB 604 KernelStack: 896 kB 605 PageTables: 324 kB 606 NFS_Unstable: 0 kB 607 Bounce: 0 kB 608 WritebackTmp: 0 kB 609 CommitLimit: 1023044 kB 610 Committed_AS: 32356 kB 611 VmallocTotal: 245760 kB 612 VmallocUsed: 0 kB 613 VmallocChunk: 0 kB 614 Percpu: 384 kB 615 CmaTotal: 131072 kB 616 CmaFree: 127928 kB 617 618 ### virtual memory: 619 620 resize2fs 1.43.4 (31-Jan-2017) 621 vm.admin_reserve_kbytes = 8192 622 vm.block_dump = 0 623 vm.compact_unevictable_allowed = 1 624 vm.dirty_background_bytes = 0 625 vm.dirty_background_ratio = 10 626 vm.dirty_bytes = 0 627 vm.dirty_expire_centisecs = 3000 628 vm.dirty_ratio = 20 629 vm.dirtytime_expire_seconds = 43200 630 vm.dirty_writeback_centisecs = 500 631 vm.drop_caches = 0 632 vm.extfrag_threshold = 500 633 vm.highmem_is_dirtyable = 0 634 vm.laptop_mode = 0 635 vm.legacy_va_layout = 0 636 vm.lowmem_reserve_ratio = 32 0 0 637 vm.max_map_count = 65530 638 vm.min_free_kbytes = 3475 639 vm.mmap_min_addr = 4096 640 vm.mmap_rnd_bits = 8 641 vm.oom_dump_tasks = 1 642 vm.oom_kill_allocating_task = 0 643 vm.overcommit_kbytes = 0 644 vm.overcommit_memory = 0 645 vm.overcommit_ratio = 50 646 vm.page-cluster = 0 647 vm.panic_on_oom = 0 648 vm.percpu_pagelist_fraction = 0 649 vm.stat_interval = 1 650 vm.swappiness = 100 651 vm.user_reserve_kbytes = 31604 652 vm.vfs_cache_pressure = 100 653 vm.watermark_scale_factor = 10 654 655 ### ip addr: 656 657 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 658 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 659 inet XXX.XXX.0.1/8 scope host lo 660 valid_lft forever preferred_lft forever 661 inet6 ::1/128 scope host 662 valid_lft forever preferred_lft forever 663 2: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN group default qlen 1000 664 link/ether 7e:04:a0:96:02:e4 brd ff:ff:ff:ff:ff:ff 665 3: eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000 666 link/ether 02:81:41:c6:e0:a6 brd ff:ff:ff:ff:ff:ff 667 4: enx00e04c680046: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000 668 link/ether 00:e0:4c:68:00:46 brd ff:ff:ff:ff:ff:ff 669 670 ### partitions: 671 672 major minor #blocks name 673 674 179 0 15558144 mmcblk0 675 179 1 15398464 mmcblk0p1 676 254 0 51200 zram0 677 254 1 511524 zram1 678 679 ### df: 680 681 udev 433M 0 433M 0% /dev 682 tmpfs 100M 3.9M 97M 4% /run 683 /dev/mmcblk0p1 2.0G 855M 1.1G 45% / 684 tmpfs 500M 0 500M 0% /dev/shm 685 tmpfs 5.0M 4.0K 5.0M 1% /run/lock 686 tmpfs 500M 0 500M 0% /sys/fs/cgroup 687 tmpfs 500M 4.0K 500M 1% /tmp 688 /dev/zram0 49M 576K 45M 2% /var/log 689 690 ### lsblk: 691 692 NAME FSTYPE SIZE MOUNTPOINT UUID 693 mmcblk0 14.9G 694 └─mmcblk0p1 ext4 14.7G / 1b49372a-ea5b-42f6-9e60-036606066891 695 zram0 50M /var/log 696 697 ### zramctl: 698 699 NAME ALGORITHM DISKSIZE DATA COMPR TOTAL STREAMS MOUNTPOINT 700 /dev/zram0 50M 660K 105K 456K 4 /var/log 701 /dev/zram1 lzo 499.5M 4K 76B 4K 4 [SWAP] 702 703 ### mtab: 704 705 /dev/mmcblk0p1 / ext4 rw,noatime,nodiratime,errors=remount-ro,commit=600 0 0 706 /dev/mmcblk0p1 /var/log.hdd ext4 rw,noatime,nodiratime,errors=remount-ro,commit=600 0 0 707 /dev/zram0 /var/log ext4 rw,relatime,block_validity,discard,delalloc,nojournal_checksum,barrier,user_xattr,acl 0 0 708 709 ### mmc0:aaaa info: 710 711 manfid: 0x000003 712 cid: 035344534c313647800bc4496a011497 713 fwrev: 0x0 714 rca: 0xaaaa 715 csd: 400e00325b59000076b27f800a404013 716 ocr: 0x00200000 717 type: SD 718 date: 04/2017 719 hwrev: 0x8 720 dsr: 0x404 721 serial: 0x0bc4496a 722 erase_size: 512 723 uevent: DRIVER=mmcblk MMC_TYPE=SD MMC_NAME=SL16G MODALIAS=mmc:block 724 ssr: 0000000004000000040090000f050a0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 0000 725 scr: 0235800300000000 726 oemid: 0x5344 727 preferred_erase_size: 4194304 728 name: SL16G 729 730 ### Boot system health: 731 732 Time CPU load %cpu %sys %usr %nice %io %irq CPU C.St. 733 00:06:28: 1368MHz 1.00 54% 20% 18% 0% 14% 0% 27.7°C 0/15 734 00:06:29: 1368MHz 1.00 37% 2% 0% 0% 34% 0% 26.9°C 0/15 735 00:06:29: 1368MHz 1.00 29% 5% 0% 0% 22% 0% 26.9°C 0/15 736 00:06:30: 1368MHz 1.00 25% 5% 0% 0% 18% 0% 26.6°C 0/15 737 00:06:30: 1368MHz 1.00 20% 5% 0% 1% 12% 0% 27.0°C 0/15 738 Filesystem at /dev/mmcblk0p1 is mounted on /; on-line resizing required 739 old_desc_blocks = 1, new_desc_blocks = 1 740 The filesystem on /dev/mmcblk0p1 is now 3849616 (4k) blocks long. 741 742 743 ### [resize2fs] Start resizing ext4 partition /dev/mmcblk0p1 now 744 745 resize2fs 1.43.4 (31-Jan-2017) 746 The filesystem is already 3849616 (4k) blocks long. Nothing to do! 747 748 749 ### quick iozone test: 4 1992 961 9045 9055 8800 3686 750 751 ### [firstrun] Recreated SSH keys (entropy: 2135 2145) 752 753 ### Activated 1 lzo zram swap devices with 499 MB each 754 755 ### Activated Armbian ramlog partition with zstd compression 756 757 Thu Jun 6 12:01:51 UTC 2019 | Orange Pi PC | 5.83 | armhf | armv7l | 4.19.38-sunxi 758 759 ### dmesg: 760 761 [ 0.000000] Booting Linux on physical CPU 0x0 762 [ 0.000000] Linux version 4.19.38-sunxi (root@nightly) (gcc version 7.4.1 20181213 [linaro-7.4-2019.02 revision 56ec6f6b99cc167ff0c2f8e1a2eed33 b1edc85d4] (Linaro GCC 7.4-2019.02)) #5.83 SMP Fri May 3 23:33:25 CEST 2019 763 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=50c5387d 764 [ 0.000000] CPU: div instructions available: patching division code 765 [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache 766 [ 0.000000] OF: fdt: Machine model: Xunlong Orange Pi PC 767 [ 0.000000] Memory policy: Data cache writealloc 768 [ 0.000000] cma: Reserved 128 MiB at 0x75c00000 769 [ 0.000000] On node 0 totalpages: 262144 770 [ 0.000000] Normal zone: 1728 pages used for memmap 771 [ 0.000000] Normal zone: 0 pages reserved 772 [ 0.000000] Normal zone: 196608 pages, LIFO batch:63 773 [ 0.000000] HighMem zone: 65536 pages, LIFO batch:15 774 [ 0.000000] psci: probing for conduit method from DT. 775 [ 0.000000] psci: Using PSCI v0.1 Function IDs from DT 776 [ 0.000000] random: get_random_bytes called from start_kernel+0x8d/0x3c6 with crng_init=0 777 [ 0.000000] percpu: Embedded 18 pages/cpu s41548 r8192 d23988 u73728 778 [ 0.000000] pcpu-alloc: s41548 r8192 d23988 u73728 alloc=18*4096 779 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 780 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260416 781 [ 0.000000] Kernel command line: root=UUID=1b49372a-ea5b-42f6-9e60-036606066891 rootwait rootfstype=ext4 console=ttyS0,115200 console=tty1 hdmi .audio=EDID:0 disp.screen0_output_mode=1920x1080p60 panic=10 consoleblank=0 loglevel=1 ubootpart=5ae5405d-01 ubootsource=mmc usb-storage.quirks=0x2537:0x1 066:u,0x2537:0x1068:u sunxi_ve_mem_reserve=0 sunxi_g2d_mem_reserve=0 sunxi_fb_mem_reserve=16 cgroup_enable=memory swapaccount=1 782 [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) 783 [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) 784 [ 0.000000] allocated 1048576 bytes of page_ext 785 [ 0.000000] Memory: 886136K/1048576K available (9216K kernel code, 1004K rwdata, 2576K rodata, 1024K init, 331K bss, 31368K reserved, 131072K c ma-reserved, 131060K highmem) 786 [ 0.000000] Virtual kernel memory layout: 787 vector : 0xffff0000 - 0xffff1000 ( 4 kB) 788 fixmap : 0xffc00000 - 0xfff00000 (3072 kB) 789 vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) 790 lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) 791 pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) 792 modules : 0xbf800000 - 0xbfe00000 ( 6 MB) 793 .text : 0x(ptrval) - 0x(ptrval) (10208 kB) 794 .init : 0x(ptrval) - 0x(ptrval) (1024 kB) 795 .data : 0x(ptrval) - 0x(ptrval) (1005 kB) 796 .bss : 0x(ptrval) - 0x(ptrval) ( 332 kB) 797 [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 798 [ 0.000000] ftrace: allocating 39959 entries in 79 pages 799 [ 0.000000] rcu: Hierarchical RCU implementation. 800 [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. 801 [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 802 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 803 [ 0.000000] GIC: Using split EOI/Deactivate mode 804 [ 0.000000] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns 805 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). 806 [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns 807 [ 0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns 808 [ 0.000014] Switching to timer-based delay loop, resolution 41ns 809 [ 0.000166] Console: colour dummy device 80x30 810 [ 0.000178] console [tty1] enabled 811 [ 0.000226] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) 812 [ 0.000236] pid_max: default: 32768 minimum: 301 813 [ 0.000431] Security Framework initialized 814 [ 0.000440] AppArmor: AppArmor disabled by boot time parameter 815 [ 0.000511] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) 816 [ 0.000520] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) 817 [ 0.001341] CPU: Testing write buffer coherency: ok 818 [ 0.001749] CPU0: update cpu_capacity 1024 819 [ 0.001756] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 820 [ 0.002235] Setting up static identity map for 0x40100000 - 0x40100054 821 [ 0.002378] rcu: Hierarchical SRCU implementation. 822 [ 0.003102] smp: Bringing up secondary CPUs ... 823 [ 0.013793] CPU1: update cpu_capacity 1024 824 [ 0.013799] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 825 [ 0.024574] CPU2: update cpu_capacity 1024 826 [ 0.024580] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 827 [ 0.035289] CPU3: update cpu_capacity 1024 828 [ 0.035294] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 829 [ 0.035386] smp: Brought up 1 node, 4 CPUs 830 [ 0.035393] SMP: Total of 4 processors activated (192.00 BogoMIPS). 831 [ 0.035397] CPU: All CPU(s) started in HYP mode. 832 [ 0.035399] CPU: Virtualization extensions available. 833 [ 0.036541] devtmpfs: initialized 834 [ 0.043017] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 835 [ 0.043268] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns 836 [ 0.043284] futex hash table entries: 1024 (order: 4, 65536 bytes) 837 [ 0.047958] xor: measuring software checksum speed 838 [ 0.087250] arm4regs : 1255.000 MB/sec 839 [ 0.127306] 8regs : 748.000 MB/sec 840 [ 0.167366] 32regs : 766.000 MB/sec 841 [ 0.207427] neon : 1270.000 MB/sec 842 [ 0.207431] xor: using function: neon (1270.000 MB/sec) 843 [ 0.207494] pinctrl core: initialized pinctrl subsystem 844 [ 0.208403] NET: Registered protocol family 16 845 [ 0.211134] DMA: preallocated 2048 KiB pool for atomic coherent allocations 846 [ 0.211625] audit: initializing netlink subsys (disabled) 847 [ 0.211777] audit: type=2000 audit(0.188:1): state=initialized audit_enabled=0 res=1 848 [ 0.212273] cpuidle: using governor ladder 849 [ 0.212301] cpuidle: using governor menu 850 [ 0.212812] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. 851 [ 0.212817] hw-breakpoint: maximum watchpoint size is 8 bytes. 852 [ 0.295927] raid6: int32x1 gen() 189 MB/s 853 [ 0.363858] raid6: int32x1 xor() 160 MB/s 854 [ 0.431888] raid6: int32x2 gen() 255 MB/s 855 [ 0.499955] raid6: int32x2 xor() 194 MB/s 856 [ 0.568098] raid6: int32x4 gen() 258 MB/s 857 [ 0.636219] raid6: int32x4 xor() 193 MB/s 858 [ 0.704222] raid6: int32x8 gen() 247 MB/s 859 [ 0.772446] raid6: int32x8 xor() 172 MB/s 860 [ 0.840484] raid6: neonx1 gen() 495 MB/s 861 [ 0.908528] raid6: neonx1 xor() 460 MB/s 862 [ 0.976670] raid6: neonx2 gen() 664 MB/s 863 [ 1.044736] raid6: neonx2 xor() 594 MB/s 864 [ 1.112873] raid6: neonx4 gen() 798 MB/s 865 [ 1.180930] raid6: neonx4 xor() 669 MB/s 866 [ 1.249017] raid6: neonx8 gen() 716 MB/s 867 [ 1.317142] raid6: neonx8 xor() 606 MB/s 868 [ 1.317145] raid6: using algorithm neonx4 gen() 798 MB/s 869 [ 1.317148] raid6: .... xor() 669 MB/s, rmw enabled 870 [ 1.317152] raid6: using neon recovery algorithm 871 [ 1.318522] SCSI subsystem initialized 872 [ 1.318705] libata version 3.00 loaded. 873 [ 1.318898] usbcore: registered new interface driver usbfs 874 [ 1.318938] usbcore: registered new interface driver hub 875 [ 1.319001] usbcore: registered new device driver usb 876 [ 1.319172] media: Linux media interface: v0.10 877 [ 1.319200] videodev: Linux video capture interface: v2.00 878 [ 1.319316] pps_core: LinuxPPS API ver. 1 registered 879 [ 1.319321] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> 880 [ 1.319336] PTP clock support registered 881 [ 1.320915] clocksource: Switched to clocksource arch_sys_counter 882 [ 1.424029] VFS: Disk quotas dquot_6.6.0 883 [ 1.424105] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) 884 [ 1.431638] NET: Registered protocol family 2 885 [ 1.432326] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) 886 [ 1.432354] TCP established hash table entries: 8192 (order: 3, 32768 bytes) 887 [ 1.432441] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) 888 [ 1.432552] TCP: Hash tables configured (established 8192 bind 8192) 889 [ 1.432663] UDP hash table entries: 512 (order: 2, 16384 bytes) 890 [ 1.432723] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) 891 [ 1.433009] NET: Registered protocol family 1 892 [ 1.433502] RPC: Registered named UNIX socket transport module. 893 [ 1.433507] RPC: Registered udp transport module. 894 [ 1.433510] RPC: Registered tcp transport module. 895 [ 1.433513] RPC: Registered tcp NFSv4.1 backchannel transport module. 896 [ 1.433738] Trying to unpack rootfs image as initramfs... 897 [ 1.732189] Freeing initrd memory: 4816K 898 [ 1.733980] Initialise system trusted keyrings 899 [ 1.734199] workingset: timestamp_bits=14 max_order=18 bucket_order=4 900 [ 1.739825] zbud: loaded 901 [ 1.741967] NFS: Registering the id_resolver key type 902 [ 1.741997] Key type id_resolver registered 903 [ 1.742001] Key type id_legacy registered 904 [ 1.742013] nfs4filelayout_init: NFSv4 File Layout Driver Registering... 905 [ 1.742017] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). 906 [ 1.743080] JFS: nTxBlock = 7984, nTxLock = 63876 907 [ 1.751794] SGI XFS with ACLs, security attributes, realtime, no debug enabled 908 [ 1.759265] Key type asymmetric registered 909 [ 1.759274] Asymmetric key parser 'x509' registered 910 [ 1.759333] bounce: pool size: 64 pages 911 [ 1.759410] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) 912 [ 1.759549] io scheduler noop registered 913 [ 1.759553] io scheduler deadline registered 914 [ 1.759749] io scheduler cfq registered (default) 915 [ 1.759755] io scheduler mq-deadline registered 916 [ 1.759759] io scheduler kyber registered 917 [ 1.759884] io scheduler bfq registered 918 [ 1.761028] sun4i-usb-phy 1c19400.phy: Couldn't request ID GPIO 919 [ 1.764991] sun8i-h3-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver 920 [ 1.766487] sun8i-h3-r-pinctrl 1f02c00.pinctrl: initialized sunXi PIO driver 921 [ 1.814770] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled 922 [ 1.816981] console [ttyS0] disabled 923 [ 1.837124] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 42, base_baud = 1500000) is a U6_16550A 924 [ 1.837179] console [ttyS0] enabled 925 [ 1.860495] sun4i-drm display-engine: bound 1100000.mixer (ops 0xc0a85d08) 926 [ 1.860741] sun4i-drm display-engine: bound 1c0c000.lcd-controller (ops 0xc0a83454) 927 [ 1.860794] sun8i-dw-hdmi 1ee0000.hdmi: 1ee0000.hdmi supply hvcc not found, using dummy regulator 928 [ 1.860850] sun8i-dw-hdmi 1ee0000.hdmi: Linked as a consumer to regulator.0 929 [ 1.861684] sun8i-dw-hdmi 1ee0000.hdmi: Detected HDMI TX controller v1.32a with HDCP (sun8i_dw_hdmi_phy) 930 [ 1.862031] sun8i-dw-hdmi 1ee0000.hdmi: registered DesignWare HDMI I2C bus driver 931 [ 1.862262] sun4i-drm display-engine: bound 1ee0000.hdmi (ops 0xc0a8578c) 932 [ 1.862267] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). 933 [ 1.862271] [drm] No driver support for vblank timestamp query. 934 [ 1.862334] [drm] Cannot find any crtc or sizes 935 [ 1.862784] [drm] Initialized sun4i-drm 1.0.0 20150629 for display-engine on minor 0 936 [ 1.865762] brd: module loaded 937 [ 1.871120] loop: module loaded 938 [ 1.873417] libphy: Fixed MDIO Bus: probed 939 [ 1.873950] dwmac-sun8i 1c30000.ethernet: PTP uses main clock 940 [ 1.873986] dwmac-sun8i 1c30000.ethernet: No regulator found 941 [ 1.874280] dwmac-sun8i 1c30000.ethernet: Current syscon value is not the default 148000 (expect 58000) 942 [ 1.874297] dwmac-sun8i 1c30000.ethernet: No HW DMA feature register supported 943 [ 1.874303] dwmac-sun8i 1c30000.ethernet: RX Checksum Offload Engine supported 944 [ 1.874308] dwmac-sun8i 1c30000.ethernet: COE Type 2 945 [ 1.874314] dwmac-sun8i 1c30000.ethernet: TX Checksum insertion supported 946 [ 1.874320] dwmac-sun8i 1c30000.ethernet: Normal descriptors 947 [ 1.874325] dwmac-sun8i 1c30000.ethernet: Chain mode enabled 948 [ 1.874458] libphy: stmmac: probed 949 [ 1.874894] dwmac-sun8i 1c30000.ethernet: Found internal PHY node 950 [ 1.874979] libphy: mdio_mux: probed 951 [ 1.874998] dwmac-sun8i 1c30000.ethernet: Switch mux to internal PHY 952 [ 1.875005] dwmac-sun8i 1c30000.ethernet: Powering internal PHY 953 [ 1.879722] libphy: mdio_mux: probed 954 [ 1.880623] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver 955 [ 1.880628] ehci-platform: EHCI generic platform driver 956 [ 1.880808] ehci-platform 1c1a000.usb: EHCI Host Controller 957 [ 1.880835] ehci-platform 1c1a000.usb: new USB bus registered, assigned bus number 1 958 [ 1.881582] ehci-platform 1c1a000.usb: irq 26, io mem 0x01c1a000 959 [ 1.896918] ehci-platform 1c1a000.usb: USB 2.0 started, EHCI 1.00 960 [ 1.897205] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 961 [ 1.897212] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 962 [ 1.897218] usb usb1: Product: EHCI Host Controller 963 [ 1.897224] usb usb1: Manufacturer: Linux 4.19.38-sunxi ehci_hcd 964 [ 1.897229] usb usb1: SerialNumber: 1c1a000.usb 965 [ 1.897794] hub 1-0:1.0: USB hub found 966 [ 1.897839] hub 1-0:1.0: 1 port detected 967 [ 1.898649] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver 968 [ 1.898673] ohci-platform: OHCI generic platform driver 969 [ 1.898823] ohci-platform 1c1a400.usb: Generic Platform OHCI controller 970 [ 1.898844] ohci-platform 1c1a400.usb: new USB bus registered, assigned bus number 2 971 [ 1.899003] ohci-platform 1c1a400.usb: irq 27, io mem 0x01c1a400 972 [ 1.961151] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19 973 [ 1.961158] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 974 [ 1.961164] usb usb2: Product: Generic Platform OHCI controller 975 [ 1.961169] usb usb2: Manufacturer: Linux 4.19.38-sunxi ohci_hcd 976 [ 1.961175] usb usb2: SerialNumber: 1c1a400.usb 977 [ 1.961611] hub 2-0:1.0: USB hub found 978 [ 1.961652] hub 2-0:1.0: 1 port detected 979 [ 1.962784] usbcore: registered new interface driver usb-storage 980 [ 1.963508] sun6i-rtc 1f00000.rtc: rtc core: registered rtc-sun6i as rtc0 981 [ 1.963515] sun6i-rtc 1f00000.rtc: RTC enabled 982 [ 1.963715] i2c /dev entries driver 983 [ 1.965710] sunxi-wdt 1c20ca0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) 984 [ 1.966465] sunxi-mmc 1c0f000.mmc: Linked as a consumer to regulator.2 985 [ 1.966951] sunxi-mmc 1c0f000.mmc: Got CD GPIO 986 [ 1.967222] ledtrig-cpu: registered to indicate activity on CPUs 987 [ 1.967295] hidraw: raw HID events driver (C) Jiri Kosina 988 [ 1.967404] usbcore: registered new interface driver usbhid 989 [ 1.967407] usbhid: USB HID core driver 990 [ 1.973490] Initializing XFRM netlink socket 991 [ 1.974156] NET: Registered protocol family 10 992 [ 1.988710] Segment Routing with IPv6 993 [ 1.988806] NET: Registered protocol family 17 994 [ 1.988831] NET: Registered protocol family 15 995 [ 1.988889] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this . 996 [ 1.988993] 8021q: 802.1Q VLAN Support v1.8 997 [ 1.989267] Key type dns_resolver registered 998 [ 1.989705] Registering SWP/SWPB emulation handler 999 [ 1.990242] registered taskstats version 1 1000 [ 1.990247] Loading compiled-in X.509 certificates 1001 [ 1.990336] zswap: loaded using pool lzo/zbud 1002 [ 1.992077] Btrfs loaded, crc32c=crc32c-generic 1003 [ 1.992280] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB 1004 [ 1.999103] Key type encrypted registered 1005 [ 2.007857] sun4i-usb-phy 1c19400.phy: Linked as a consumer to regulator.4 1006 [ 2.008802] ehci-platform 1c1b000.usb: EHCI Host Controller 1007 [ 2.008834] ehci-platform 1c1b000.usb: new USB bus registered, assigned bus number 3 1008 [ 2.009397] ehci-platform 1c1b000.usb: irq 28, io mem 0x01c1b000 1009 [ 2.024922] ehci-platform 1c1b000.usb: USB 2.0 started, EHCI 1.00 1010 [ 2.025130] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 1011 [ 2.025137] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 1012 [ 2.025143] usb usb3: Product: EHCI Host Controller 1013 [ 2.025148] usb usb3: Manufacturer: Linux 4.19.38-sunxi ehci_hcd 1014 [ 2.025154] usb usb3: SerialNumber: 1c1b000.usb 1015 [ 2.025678] hub 3-0:1.0: USB hub found 1016 [ 2.025715] hub 3-0:1.0: 1 port detected 1017 [ 2.026484] ehci-platform 1c1c000.usb: EHCI Host Controller 1018 [ 2.026506] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 4 1019 [ 2.026720] ehci-platform 1c1c000.usb: irq 30, io mem 0x01c1c000 1020 [ 2.029005] mmc0: host does not support reading read-only switch, assuming write-enable 1021 [ 2.031999] mmc0: new high speed SDHC card at address aaaa 1022 [ 2.033268] mmcblk0: mmc0:aaaa SL16G 14.8 GiB 1023 [ 2.035621] mmcblk0: p1 1024 [ 2.040933] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 1025 [ 2.041141] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 1026 [ 2.041149] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 1027 [ 2.041154] usb usb4: Product: EHCI Host Controller 1028 [ 2.041160] usb usb4: Manufacturer: Linux 4.19.38-sunxi ehci_hcd 1029 [ 2.041165] usb usb4: SerialNumber: 1c1c000.usb 1030 [ 2.041641] hub 4-0:1.0: USB hub found 1031 [ 2.041679] hub 4-0:1.0: 1 port detected 1032 [ 2.042533] ehci-platform 1c1d000.usb: EHCI Host Controller 1033 [ 2.042558] ehci-platform 1c1d000.usb: new USB bus registered, assigned bus number 5 1034 [ 2.042887] ehci-platform 1c1d000.usb: irq 32, io mem 0x01c1d000 1035 [ 2.056937] ehci-platform 1c1d000.usb: USB 2.0 started, EHCI 1.00 1036 [ 2.057124] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 1037 [ 2.057131] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 1038 [ 2.057136] usb usb5: Product: EHCI Host Controller 1039 [ 2.057142] usb usb5: Manufacturer: Linux 4.19.38-sunxi ehci_hcd 1040 [ 2.057147] usb usb5: SerialNumber: 1c1d000.usb 1041 [ 2.057590] hub 5-0:1.0: USB hub found 1042 [ 2.057626] hub 5-0:1.0: 1 port detected 1043 [ 2.058336] ohci-platform 1c1b400.usb: Generic Platform OHCI controller 1044 [ 2.058358] ohci-platform 1c1b400.usb: new USB bus registered, assigned bus number 6 1045 [ 2.058517] ohci-platform 1c1b400.usb: irq 29, io mem 0x01c1b400 1046 [ 2.121112] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19 1047 [ 2.121119] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 1048 [ 2.121125] usb usb6: Product: Generic Platform OHCI controller 1049 [ 2.121130] usb usb6: Manufacturer: Linux 4.19.38-sunxi ohci_hcd 1050 [ 2.121135] usb usb6: SerialNumber: 1c1b400.usb 1051 [ 2.121573] hub 6-0:1.0: USB hub found 1052 [ 2.121608] hub 6-0:1.0: 1 port detected 1053 [ 2.122279] ohci-platform 1c1c400.usb: Generic Platform OHCI controller 1054 [ 2.122299] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 7 1055 [ 2.122443] ohci-platform 1c1c400.usb: irq 31, io mem 0x01c1c400 1056 [ 2.185103] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19 1057 [ 2.185110] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 1058 [ 2.185116] usb usb7: Product: Generic Platform OHCI controller 1059 [ 2.185121] usb usb7: Manufacturer: Linux 4.19.38-sunxi ohci_hcd 1060 [ 2.185126] usb usb7: SerialNumber: 1c1c400.usb 1061 [ 2.185557] hub 7-0:1.0: USB hub found 1062 [ 2.185595] hub 7-0:1.0: 1 port detected 1063 [ 2.186273] ohci-platform 1c1d400.usb: Generic Platform OHCI controller 1064 [ 2.186292] ohci-platform 1c1d400.usb: new USB bus registered, assigned bus number 8 1065 [ 2.186475] ohci-platform 1c1d400.usb: irq 33, io mem 0x01c1d400 1066 [ 2.249092] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19 1067 [ 2.249101] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1 1068 [ 2.249106] usb usb8: Product: Generic Platform OHCI controller 1069 [ 2.249112] usb usb8: Manufacturer: Linux 4.19.38-sunxi ohci_hcd 1070 [ 2.249117] usb usb8: SerialNumber: 1c1d400.usb 1071 [ 2.249565] hub 8-0:1.0: USB hub found 1072 [ 2.249599] hub 8-0:1.0: 1 port detected 1073 [ 2.250323] usb_phy_generic usb_phy_generic.2.auto: usb_phy_generic.2.auto supply vcc not found, using dummy regulator 1074 [ 2.250387] usb_phy_generic usb_phy_generic.2.auto: Linked as a consumer to regulator.0 1075 [ 2.250684] musb-hdrc musb-hdrc.3.auto: MUSB HDRC host driver 1076 [ 2.250694] musb-hdrc musb-hdrc.3.auto: new USB bus registered, assigned bus number 9 1077 [ 2.250922] usb usb9: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 1078 [ 2.250929] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1 1079 [ 2.250935] usb usb9: Product: MUSB HDRC host driver 1080 [ 2.250940] usb usb9: Manufacturer: Linux 4.19.38-sunxi musb-hcd 1081 [ 2.250945] usb usb9: SerialNumber: musb-hdrc.3.auto 1082 [ 2.251353] hub 9-0:1.0: USB hub found 1083 [ 2.251393] hub 9-0:1.0: 1 port detected 1084 [ 2.252352] sun6i-rtc 1f00000.rtc: setting system clock to 1970-01-01 00:00:16 UTC (16) 1085 [ 2.252539] of_cfs_init 1086 [ 2.252640] of_cfs_init: OK 1087 [ 2.252789] vcc3v0: disabling 1088 [ 2.252795] vcc5v0: disabling 1089 [ 2.252800] usb0-vbus: disabling 1090 [ 2.256103] Freeing unused kernel memory: 1024K 1091 [ 2.273110] Run /init as init process 1092 [ 2.318675] random: systemd-udevd: uninitialized urandom read (16 bytes read) 1093 [ 2.319222] random: systemd-udevd: uninitialized urandom read (16 bytes read) 1094 [ 2.319332] random: systemd-udevd: uninitialized urandom read (16 bytes read) 1095 [ 2.881076] [drm] Cannot find any crtc or sizes 1096 [ 3.368410] random: fast init done 1097 [ 3.395139] EXT4-fs (mmcblk0p1): mounted filesystem with writeback data mode. Opts: (null) 1098 [ 3.864166] systemd[1]: System time before build time, advancing clock. 1099 [ 3.910168] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN) 1100 [ 3.910663] systemd[1]: Detected architecture arm. 1101 [ 3.915039] systemd[1]: Set hostname to <orangepipc>. 1102 [ 4.273938] systemd[1]: Listening on udev Kernel Socket. 1103 [ 4.274858] systemd[1]: Listening on Journal Socket. 1104 [ 4.275366] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. 1105 [ 4.275990] systemd[1]: Listening on Journal Audit Socket. 1106 [ 4.276355] systemd[1]: Listening on fsck to fsckd communication Socket. 1107 [ 4.276709] systemd[1]: Listening on Journal Socket (/dev/log). 1108 [ 4.277805] systemd[1]: Created slice User and Session Slice. 1109 [ 4.441925] EXT4-fs (mmcblk0p1): re-mounted. Opts: commit=600,errors=remount-ro 1110 [ 4.694642] systemd-journald[220]: Received request to flush runtime journal from PID 1 1111 [ 5.158977] cpu cpu0: Linked as a consumer to regulator.5 1112 [ 5.159176] cpu cpu0: Dropping the link to regulator.5 1113 [ 5.159431] cpu cpu0: Linked as a consumer to regulator.5 1114 [ 5.160854] input: r_gpio_keys as /devices/platform/r_gpio_keys/input/input0 1115 [ 5.323633] sun8i_ths 1c25000.thermal-sensor: no memory resources defined 1116 [ 5.323666] sun8i_ths: probe of 1c25000.thermal-sensor failed with error -22 1117 [ 5.392640] Registered IR keymap rc-empty 1118 [ 5.392767] rc rc0: sunxi-ir as /devices/platform/soc/1f02000.ir/rc/rc0 1119 [ 5.392967] input: sunxi-ir as /devices/platform/soc/1f02000.ir/rc/rc0/input1 1120 [ 5.394149] rc rc0: lirc_dev: driver sunxi-ir registered at minor = 0, raw IR receiver, no transmitter 1121 [ 5.396180] sunxi-ir 1f02000.ir: initialized sunXi IR driver 1122 [ 5.396355] thermal thermal_zone0: failed to read out thermal zone (-110) 1123 [ 5.418284] sun4i-codec 1c22c00.codec: ASoC: codec-analog@1f015c0 not registered 1124 [ 5.418298] sun4i-codec 1c22c00.codec: Failed to register our card 1125 [ 5.433598] sun4i-codec 1c22c00.codec: ASoC: Failed to create component debugfs directory 1126 [ 5.439954] sun4i-codec 1c22c00.codec: Codec <-> 1c22c00.codec mapping ok 1127 [ 5.445995] lima 1c40000.gpu: bus rate = 200000000 1128 [ 5.446007] lima 1c40000.gpu: mod rate = 384000000 1129 [ 5.452312] [TTM] Zone kernel: Available graphics memory: 380458 kiB 1130 [ 5.452321] [TTM] Zone highmem: Available graphics memory: 511524 kiB 1131 [ 5.452324] [TTM] Initializing pool allocator 1132 [ 5.453082] lima 1c40000.gpu: gp - mali400 version major 1 minor 1 1133 [ 5.453146] lima 1c40000.gpu: pp0 - mali400 version major 1 minor 1 1134 [ 5.453188] lima 1c40000.gpu: pp1 - mali400 version major 1 minor 1 1135 [ 5.453223] lima 1c40000.gpu: l2 cache 64K, 4-way, 64byte cache line, 64bit external bus 1136 [ 5.454622] [drm] Initialized lima 1.0.0 20170325 for 1c40000.gpu on minor 1 1137 [ 5.532984] zram: Added device: zram0 1138 [ 5.541161] zram: Added device: zram1 1139 [ 5.541768] zram: Added device: zram2 1140 [ 5.611890] zram1: detected capacity change from 0 to 523800576 1141 [ 5.677549] Adding 511520k swap on /dev/zram1. Priority:5 extents:1 across:511520k SSFS 1142 [ 5.823413] zram0: detected capacity change from 0 to 52428800 1143 [ 6.494335] EXT4-fs (zram0): mounted filesystem without journal. Opts: discard 1144 [ 6.531270] random: crng init done 1145 [ 6.531283] random: 7 urandom warning(s) missed due to ratelimiting 1146 1147 ### armbian-release: 1148 1149 # PLEASE DO NOT EDIT THIS FILE 1150 BOARD=orangepipc 1151 BOARD_NAME="Orange Pi PC" 1152 BOARDFAMILY=sun8i 1153 VERSION=5.83 1154 LINUXFAMILY=sunxi 1155 BRANCH=next 1156 ARCH=arm 1157 IMAGE_TYPE=stable 1158 BOARD_TYPE=conf 1159 INITRD_ARCH=arm 1160 KERNEL_IMAGE_TYPE=zImage 1161 1162 ### boot environment: 1163 1164 verbosity=1 1165 logo=disabled 1166 console=both 1167 disp_mode=1920x1080p60 1168 overlay_prefix=sun8i-h3 1169 rootdev=UUID=1b49372a-ea5b-42f6-9e60-036606066891 1170 rootfstype=ext4 1171 usbstoragequirks=0x2537:0x1066:u,0x2537:0x1068:u 1172 1173 ### lsusb: 1174 1175 Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub 1176 Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub 1177 Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub 1178 Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub 1179 Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub 1180 Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub 1181 Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub 1182 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub 1183 Bus 009 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub 1184 1185 ### lscpu: 1186 1187 Architecture: armv7l 1188 Byte Order: Little Endian 1189 CPU(s): 4 1190 On-line CPU(s) list: 0-3 1191 Thread(s) per core: 1 1192 Core(s) per socket: 4 1193 Socket(s): 1 1194 Model: 5 1195 Model name: ARMv7 Processor rev 5 (v7l) 1196 CPU max MHz: 1368.0000 1197 CPU min MHz: 120.0000 1198 BogoMIPS: 61.71 1199 Flags: half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm 1200 1201 ### cpuinfo: 1202 1203 processor : 0 1204 model name : ARMv7 Processor rev 5 (v7l) 1205 BogoMIPS : 61.71 1206 Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm 1207 CPU implementer : 0x41 1208 CPU architecture: 7 1209 CPU variant : 0x0 1210 CPU part : 0xc07 1211 CPU revision : 5 1212 1213 processor : 1 1214 model name : ARMv7 Processor rev 5 (v7l) 1215 BogoMIPS : 61.71 1216 Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm 1217 CPU implementer : 0x41 1218 CPU architecture: 7 1219 CPU variant : 0x0 1220 CPU part : 0xc07 1221 CPU revision : 5 1222 1223 processor : 2 1224 model name : ARMv7 Processor rev 5 (v7l) 1225 BogoMIPS : 61.71 1226 Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm 1227 CPU implementer : 0x41 1228 CPU architecture: 7 1229 CPU variant : 0x0 1230 CPU part : 0xc07 1231 CPU revision : 5 1232 1233 processor : 3 1234 model name : ARMv7 Processor rev 5 (v7l) 1235 BogoMIPS : 61.71 1236 Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm 1237 CPU implementer : 0x41 1238 CPU architecture: 7 1239 CPU variant : 0x0 1240 CPU part : 0xc07 1241 CPU revision : 5 1242 1243 Hardware : Allwinner sun8i Family 1244 Revision : 0000 1245 Serial : 02c0008141c6e0a6 1246 1247 ### meminfo: 1248 1249 MemTotal: 1023048 kB 1250 MemFree: 904308 kB 1251 MemAvailable: 942232 kB 1252 Buffers: 8512 kB 1253 Cached: 40860 kB 1254 SwapCached: 0 kB 1255 Active: 34612 kB 1256 Inactive: 28012 kB 1257 Active(anon): 13436 kB 1258 Inactive(anon): 3860 kB 1259 Active(file): 21176 kB 1260 Inactive(file): 24152 kB 1261 Unevictable: 0 kB 1262 Mlocked: 0 kB 1263 HighTotal: 262132 kB 1264 HighFree: 190244 kB 1265 LowTotal: 760916 kB 1266 LowFree: 714064 kB 1267 SwapTotal: 511520 kB 1268 SwapFree: 511520 kB 1269 Dirty: 120 kB 1270 Writeback: 0 kB 1271 AnonPages: 13168 kB 1272 Mapped: 18252 kB 1273 Shmem: 3972 kB 1274 Slab: 24212 kB 1275 SReclaimable: 11660 kB 1276 SUnreclaim: 12552 kB 1277 KernelStack: 992 kB 1278 PageTables: 620 kB 1279 NFS_Unstable: 0 kB 1280 Bounce: 0 kB 1281 WritebackTmp: 0 kB 1282 CommitLimit: 1023044 kB 1283 Committed_AS: 88924 kB 1284 VmallocTotal: 245760 kB 1285 VmallocUsed: 0 kB 1286 VmallocChunk: 0 kB 1287 Percpu: 384 kB 1288 CmaTotal: 131072 kB 1289 CmaFree: 127932 kB 1290 1291 ### virtual memory: 1292 1293 vm.admin_reserve_kbytes = 8192 1294 vm.block_dump = 0 1295 vm.compact_unevictable_allowed = 1 1296 vm.dirty_background_bytes = 0 1297 vm.dirty_background_ratio = 10 1298 vm.dirty_bytes = 0 1299 vm.dirty_expire_centisecs = 3000 1300 vm.dirty_ratio = 20 1301 vm.dirtytime_expire_seconds = 43200 1302 vm.dirty_writeback_centisecs = 500 1303 vm.drop_caches = 0 1304 vm.extfrag_threshold = 500 1305 vm.highmem_is_dirtyable = 0 1306 vm.laptop_mode = 0 1307 vm.legacy_va_layout = 0 1308 vm.lowmem_reserve_ratio = 32 0 0 1309 vm.max_map_count = 65530 1310 vm.min_free_kbytes = 3475 1311 vm.mmap_min_addr = 4096 1312 vm.mmap_rnd_bits = 8 1313 vm.oom_dump_tasks = 1 1314 vm.oom_kill_allocating_task = 0 1315 vm.overcommit_kbytes = 0 1316 vm.overcommit_memory = 0 1317 vm.overcommit_ratio = 50 1318 vm.page-cluster = 0 1319 vm.panic_on_oom = 0 1320 vm.percpu_pagelist_fraction = 0 1321 vm.stat_interval = 1 1322 vm.swappiness = 100 1323 vm.user_reserve_kbytes = 31604 1324 vm.vfs_cache_pressure = 100 1325 vm.watermark_scale_factor = 10 1326 1327 ### ip addr: 1328 1329 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 1330 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 1331 inet XXX.XXX.0.1/8 scope host lo 1332 valid_lft forever preferred_lft forever 1333 inet6 ::1/128 scope host 1334 valid_lft forever preferred_lft forever 1335 2: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN group default qlen 1000 1336 link/ether be:e0:25:96:94:e2 brd ff:ff:ff:ff:ff:ff 1337 3: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN group default qlen 1000 1338 link/ether 02:81:41:c6:e0:a6 brd ff:ff:ff:ff:ff:ff 1339 1340 ### partitions: 1341 1342 major minor #blocks name 1343 1344 179 0 15558144 mmcblk0 1345 179 1 15398464 mmcblk0p1 1346 254 0 51200 zram0 1347 254 1 511524 zram1 1348 1349 ### df: 1350 1351 udev 433M 0 433M 0% /dev 1352 tmpfs 100M 3.9M 97M 4% /run 1353 /dev/mmcblk0p1 15G 1.3G 14G 9% / 1354 tmpfs 500M 0 500M 0% /dev/shm 1355 tmpfs 5.0M 4.0K 5.0M 1% /run/lock 1356 tmpfs 500M 0 500M 0% /sys/fs/cgroup 1357 tmpfs 500M 4.0K 500M 1% /tmp 1358 /dev/zram0 49M 2.0M 44M 5% /var/log 1359 1360 ### lsblk: 1361 1362 NAME FSTYPE SIZE MOUNTPOINT UUID 1363 mmcblk0 14.9G 1364 └─mmcblk0p1 ext4 14.7G / 1b49372a-ea5b-42f6-9e60-036606066891 1365 zram0 50M /var/log 1366 1367 ### zramctl: 1368 1369 NAME ALGORITHM DISKSIZE DATA COMPR TOTAL STREAMS MOUNTPOINT 1370 /dev/zram0 50M 2M 324.6K 680K 4 /var/log 1371 /dev/zram1 lzo 499.5M 4K 76B 4K 4 [SWAP] 1372 1373 ### mtab: 1374 1375 /dev/mmcblk0p1 / ext4 rw,noatime,nodiratime,errors=remount-ro,commit=600 0 0 1376 /dev/mmcblk0p1 /var/log.hdd ext4 rw,noatime,nodiratime,errors=remount-ro,commit=600 0 0 1377 /dev/zram0 /var/log ext4 rw,relatime,block_validity,discard,delalloc,nojournal_checksum,barrier,user_xattr,acl 0 0 1378 1379 ### mmc0:aaaa info: 1380 1381 manfid: 0x000003 1382 cid: 035344534c313647800bc4496a011497 1383 fwrev: 0x0 1384 rca: 0xaaaa 1385 csd: 400e00325b59000076b27f800a404013 1386 ocr: 0x00200000 1387 type: SD 1388 date: 04/2017 1389 hwrev: 0x8 1390 dsr: 0x404 1391 serial: 0x0bc4496a 1392 erase_size: 512 1393 uevent: DRIVER=mmcblk MMC_TYPE=SD MMC_NAME=SL16G MODALIAS=mmc:block 1394 ssr: 0000000004000000040090000f050a0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 0000 1395 scr: 0235800300000000 1396 oemid: 0x5344 1397 preferred_erase_size: 4194304 1398 name: SL16G 1399 1400 ### Boot system health: 1401 1402 Time CPU load %cpu %sys %usr %nice %io %irq CPU C.St. 1403 12:01:54: 1296MHz 0.77 62% 27% 28% 0% 6% 0% 29.5°C 0/15 1404 12:01:54: 1296MHz 0.77 35% 7% 3% 1% 23% 0% 27.2°C 0/15 1405 12:01:55: 1296MHz 0.77 40% 9% 2% 2% 25% 0% 27.3°C 0/15 1406 12:01:55: 1296MHz 0.77 36% 6% 2% 1% 24% 0% 26.6°C 0/15 1407 12:01:56: 1296MHz 0.77 48% 11% 17% 1% 17% 0% 28.7°C 0/15 1408 1409 ### lsusb: 1410 1411 Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub 1412 Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub 1413 Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub 1414 Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub 1415 Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub 1416 Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub 1417 Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub 1418 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub 1419 Bus 009 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub 1420 1421 /: Bus 09.Port 1: Dev 1, Class=root_hub, Driver=musb-hdrc/1p, 480M 1422 /: Bus 08.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M 1423 /: Bus 07.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M 1424 /: Bus 06.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M 1425 /: Bus 05.Port 1: Dev 1, Class=root_hub, Driver=ehci-platform/1p, 480M 1426 /: Bus 04.Port 1: Dev 1, Class=root_hub, Driver=ehci-platform/1p, 480M 1427 /: Bus 03.Port 1: Dev 1, Class=root_hub, Driver=ehci-platform/1p, 480M 1428 /: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=ohci-platform/1p, 12M 1429 /: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=ehci-platform/1p, 480M 1430 1431 ### Group membership of pi : pi dialout sudo audio video plugdev systemd-journal input netdev ssh 1432 1433 ### Installed packages: 1434 1435 ii armbian-config 5.83 all Armbian configuration utility 1436 ii armbian-firmware 5.83 all Linux firmware 1437 ii armbian-tools-stretch 5.83 armhf Armbian tools, Cubie bt utils 1438 ii hostapd 3:2.7-99~armbian5.73+1 armhf IEEE 802.11 AP and IEEE 802.1X/WPA/WPA2/EAP Authenticator 1439 ii linux-base 4.5 all Linux image base package 1440 ii linux-dtb-next-sunxi 5.83 armhf Linux DTB, version 4.19.38-sunxi 1441 ii linux-image-next-sunxi 5.83 armhf Linux kernel, version 4.19.38-sunxi 1442 ii linux-libc-dev 5.70 armhf Linux support headers for userspace development 1443 ii linux-stretch-root-next-orangepipc 5.83 armhf Armbian tweaks for stretch on orangepipc (next branch) 1444 ii linux-u-boot-orangepipc-next 5.83 armhf Uboot loader 2019.04 1445 ii sunxi-tools 1.4.2-2~armbian5.73+1 armhf tools for working with Allwinner (sunxi) ARM processors 1446 1447 ### Loaded modules: 1448 1449 Module Size Used by 1450 evdev 20480 1 1451 zstd 16384 4 1452 zram 24576 2 1453 lima 40960 0 1454 gpu_sched 20480 1 lima 1455 sun8i_codec_analog 24576 1 1456 snd_soc_simple_card 16384 0 1457 ttm 57344 1 lima 1458 snd_soc_simple_card_utils 16384 1 snd_soc_simple_card 1459 sun4i_codec 32768 3 1460 sun8i_adda_pr_regmap 16384 1 sun8i_codec_analog 1461 sun4i_i2s 20480 0 1462 snd_soc_core 110592 5 sun4i_codec,sun4i_i2s,sun8i_codec_analog,snd_soc_simple_card_utils,snd_soc_simple_card 1463 sunxi_cir 16384 0 1464 sun4i_gpadc_iio 16384 0 1465 snd_pcm_dmaengine 16384 1 snd_soc_core 1466 snd_pcm 65536 4 sun4i_codec,sun4i_i2s,snd_pcm_dmaengine,snd_soc_core 1467 industrialio 49152 1 sun4i_gpadc_iio 1468 snd_timer 24576 1 snd_pcm 1469 snd 45056 3 snd_timer,snd_soc_core,snd_pcm 1470 sun8i_ths 16384 0 1471 soundcore 16384 1 snd 1472 gpio_keys 20480 0 1473 cpufreq_dt 16384 0 1474 uio_pdrv_genirq 16384 0 1475 uio 16384 1 uio_pdrv_genirq 1476 thermal_sys 57344 3 cpufreq_dt,sun8i_ths,sun4i_gpadc_iio 1477 ip_tables 20480 0 1478 x_tables 20480 1 ip_tables 1479 sy8106a_regulator 16384 1 1480 1481 ### Current system health: 1482 1483 Time CPU load %cpu %sys %usr %nice %io %irq CPU C.St. 1484 13:46:28: 1296MHz 0.01 0% 0% 0% 0% 0% 0% 31.5°C 0/15 1485 13:46:28: 1296MHz 0.01 5% 3% 0% 1% 0% 0% 29.9°C 0/15 1486 13:46:29: 1296MHz 0.01 5% 3% 0% 1% 0% 0% 29.5°C 0/15 1487 13:46:29: 480MHz 0.01 7% 6% 0% 1% 0% 0% 28.4°C 0/15 1488 13:46:29: 1296MHz 0.01 8% 5% 0% 2% 0% 0% 29.3°C 0/15 1489 13:46:33: 1296MHz 0.41 0% 0% 0% 0% 0% 0% 40.3°C 0/15 1490 13:46:33: 1296MHz 0.41 73% 0% 71% 0% 0% 0% 33.3°C 0/15 1491 13:46:34: 1296MHz 0.41 5% 3% 0% 1% 0% 0% 32.2°C 0/15 1492 13:46:34: 1296MHz 0.41 5% 5% 0% 0% 0% 0% 31.2°C 0/15 1493 13:46:34: 1296MHz 0.41 5% 3% 0% 1% 0% 0% 31.7°C 0/15 1494 1495 ### resolv.conf 1496 1497 -rw-r--r-- 1 root root 53 Jun 6 12:01 /etc/resolv.conf 1498 # Generated by NetworkManager 1499 nameserver XXX.XXX.2.1 1500 1501 ### Current sysinfo: 1502 1503 Linux 4.19.38-sunxi (orangepipc) 06/08/19 _armv7l_ (4 CPU) 1504 1505 avg-cpu: %user %nice %system %iowait %steal %idle 1506 0.37 0.00 0.16 0.03 0.00 99.44 1507 1508 Device: tps kB_read/s kB_wrtn/s kB_read kB_wrtn 1509 ram0 0.00 0.00 0.00 0 0 1510 ram1 0.00 0.00 0.00 0 0 1511 ram2 0.00 0.00 0.00 0 0 1512 ram3 0.00 0.00 0.00 0 0 1513 mmcblk0 0.79 28.27 0.36 122245 1540 1514 mmcblk0p1 0.76 27.55 0.36 119121 1540 1515 zram0 0.23 0.17 0.75 732 3240 1516 zram1 0.07 0.27 0.00 1180 4 1517 zram2 0.00 0.00 0.00 0 0 1518 1519 procs -----------------------memory---------------------- ---swap-- -----io---- -system-- --------cpu-------- 1520 r b swpd free buff cache si so bi bo in cs us sy id wa st 1521 0 0 0 753052 11368 134452 0 0 7 0 23 36 0 0 99 0 0 1522 1523 total used free shared buff/cache available 1524 Mem: 999M 121M 735M 12M 142M 842M 1525 Swap: 499M 0B 499M 1526 1527 NAME ALGORITHM DISKSIZE DATA COMPR TOTAL STREAMS MOUNTPOINT 1528 /dev/zram0 50M 2.1M 344.4K 720K 4 /var/log 1529 /dev/zram1 lzo 499.5M 4K 76B 4K 4 [SWAP] 1530 1531 13:46:35 up 1:12, 1 user, load average: 0.38, 0.09, 0.03 1532 1533 [ 1.743080] JFS: nTxBlock = 7984, nTxLock = 63876 1534 [ 1.751794] SGI XFS with ACLs, security attributes, realtime, no debug enabled 1535 [ 1.759265] Key type asymmetric registered 1536 [ 1.759274] Asymmetric key parser 'x509' registered 1537 [ 1.759333] bounce: pool size: 64 pages 1538 [ 1.759410] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) 1539 [ 1.759549] io scheduler noop registered 1540 [ 1.759553] io scheduler deadline registered 1541 [ 1.759749] io scheduler cfq registered (default) 1542 [ 1.759755] io scheduler mq-deadline registered 1543 [ 1.759759] io scheduler kyber registered 1544 [ 1.759884] io scheduler bfq registered 1545 [ 1.761028] sun4i-usb-phy 1c19400.phy: Couldn't request ID GPIO 1546 [ 1.764991] sun8i-h3-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver 1547 [ 1.766487] sun8i-h3-r-pinctrl 1f02c00.pinctrl: initialized sunXi PIO driver 1548 [ 1.814770] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled 1549 [ 1.816981] console [ttyS0] disabled 1550 [ 1.837124] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 42, base_baud = 1500000) is a U6_16550A 1551 [ 1.837179] console [ttyS0] enabled 1552 [ 1.860495] sun4i-drm display-engine: bound 1100000.mixer (ops 0xc0a85d08) 1553 [ 1.860741] sun4i-drm display-engine: bound 1c0c000.lcd-controller (ops 0xc0a83454) 1554 [ 1.860794] sun8i-dw-hdmi 1ee0000.hdmi: 1ee0000.hdmi supply hvcc not found, using dummy regulator 1555 [ 1.860850] sun8i-dw-hdmi 1ee0000.hdmi: Linked as a consumer to regulator.0 1556 [ 1.861684] sun8i-dw-hdmi 1ee0000.hdmi: Detected HDMI TX controller v1.32a with HDCP (sun8i_dw_hdmi_phy) 1557 [ 1.862031] sun8i-dw-hdmi 1ee0000.hdmi: registered DesignWare HDMI I2C bus driver 1558 [ 1.862262] sun4i-drm display-engine: bound 1ee0000.hdmi (ops 0xc0a8578c) 1559 [ 1.862267] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). 1560 [ 1.862271] [drm] No driver support for vblank timestamp query. 1561 [ 1.862334] [drm] Cannot find any crtc or sizes 1562 [ 1.862784] [drm] Initialized sun4i-drm 1.0.0 20150629 for display-engine on minor 0 1563 [ 1.865762] brd: module loaded 1564 [ 1.871120] loop: module loaded 1565 [ 1.873417] libphy: Fixed MDIO Bus: probed 1566 [ 1.873950] dwmac-sun8i 1c30000.ethernet: PTP uses main clock 1567 [ 1.873986] dwmac-sun8i 1c30000.ethernet: No regulator found 1568 [ 1.874280] dwmac-sun8i 1c30000.ethernet: Current syscon value is not the default 148000 (expect 58000) 1569 [ 1.874297] dwmac-sun8i 1c30000.ethernet: No HW DMA feature register supported 1570 [ 1.874303] dwmac-sun8i 1c30000.ethernet: RX Checksum Offload Engine supported 1571 [ 1.874308] dwmac-sun8i 1c30000.ethernet: COE Type 2 1572 [ 1.874314] dwmac-sun8i 1c30000.ethernet: TX Checksum insertion supported 1573 [ 1.874320] dwmac-sun8i 1c30000.ethernet: Normal descriptors 1574 [ 1.874325] dwmac-sun8i 1c30000.ethernet: Chain mode enabled 1575 [ 1.874458] libphy: stmmac: probed 1576 [ 1.874894] dwmac-sun8i 1c30000.ethernet: Found internal PHY node 1577 [ 1.874979] libphy: mdio_mux: probed 1578 [ 1.874998] dwmac-sun8i 1c30000.ethernet: Switch mux to internal PHY 1579 [ 1.875005] dwmac-sun8i 1c30000.ethernet: Powering internal PHY 1580 [ 1.879722] libphy: mdio_mux: probed 1581 [ 1.880623] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver 1582 [ 1.880628] ehci-platform: EHCI generic platform driver 1583 [ 1.880808] ehci-platform 1c1a000.usb: EHCI Host Controller 1584 [ 1.880835] ehci-platform 1c1a000.usb: new USB bus registered, assigned bus number 1 1585 [ 1.881582] ehci-platform 1c1a000.usb: irq 26, io mem 0x01c1a000 1586 [ 1.896918] ehci-platform 1c1a000.usb: USB 2.0 started, EHCI 1.00 1587 [ 1.897205] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 1588 [ 1.897212] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 1589 [ 1.897218] usb usb1: Product: EHCI Host Controller 1590 [ 1.897224] usb usb1: Manufacturer: Linux 4.19.38-sunxi ehci_hcd 1591 [ 1.897229] usb usb1: SerialNumber: 1c1a000.usb 1592 [ 1.897794] hub 1-0:1.0: USB hub found 1593 [ 1.897839] hub 1-0:1.0: 1 port detected 1594 [ 1.898649] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver 1595 [ 1.898673] ohci-platform: OHCI generic platform driver 1596 [ 1.898823] ohci-platform 1c1a400.usb: Generic Platform OHCI controller 1597 [ 1.898844] ohci-platform 1c1a400.usb: new USB bus registered, assigned bus number 2 1598 [ 1.899003] ohci-platform 1c1a400.usb: irq 27, io mem 0x01c1a400 1599 [ 1.961151] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19 1600 [ 1.961158] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 1601 [ 1.961164] usb usb2: Product: Generic Platform OHCI controller 1602 [ 1.961169] usb usb2: Manufacturer: Linux 4.19.38-sunxi ohci_hcd 1603 [ 1.961175] usb usb2: SerialNumber: 1c1a400.usb 1604 [ 1.961611] hub 2-0:1.0: USB hub found 1605 [ 1.961652] hub 2-0:1.0: 1 port detected 1606 [ 1.962784] usbcore: registered new interface driver usb-storage 1607 [ 1.963508] sun6i-rtc 1f00000.rtc: rtc core: registered rtc-sun6i as rtc0 1608 [ 1.963515] sun6i-rtc 1f00000.rtc: RTC enabled 1609 [ 1.963715] i2c /dev entries driver 1610 [ 1.965710] sunxi-wdt 1c20ca0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) 1611 [ 1.966465] sunxi-mmc 1c0f000.mmc: Linked as a consumer to regulator.2 1612 [ 1.966951] sunxi-mmc 1c0f000.mmc: Got CD GPIO 1613 [ 1.967222] ledtrig-cpu: registered to indicate activity on CPUs 1614 [ 1.967295] hidraw: raw HID events driver (C) Jiri Kosina 1615 [ 1.967404] usbcore: registered new interface driver usbhid 1616 [ 1.967407] usbhid: USB HID core driver 1617 [ 1.973490] Initializing XFRM netlink socket 1618 [ 1.974156] NET: Registered protocol family 10 1619 [ 1.988710] Segment Routing with IPv6 1620 [ 1.988806] NET: Registered protocol family 17 1621 [ 1.988831] NET: Registered protocol family 15 1622 [ 1.988889] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. 1623 [ 1.988993] 8021q: 802.1Q VLAN Support v1.8 1624 [ 1.989267] Key type dns_resolver registered 1625 [ 1.989705] Registering SWP/SWPB emulation handler 1626 [ 1.990242] registered taskstats version 1 1627 [ 1.990247] Loading compiled-in X.509 certificates 1628 [ 1.990336] zswap: loaded using pool lzo/zbud 1629 [ 1.992077] Btrfs loaded, crc32c=crc32c-generic 1630 [ 1.992280] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB 1631 [ 1.999103] Key type encrypted registered 1632 [ 2.007857] sun4i-usb-phy 1c19400.phy: Linked as a consumer to regulator.4 1633 [ 2.008802] ehci-platform 1c1b000.usb: EHCI Host Controller 1634 [ 2.008834] ehci-platform 1c1b000.usb: new USB bus registered, assigned bus number 3 1635 [ 2.009397] ehci-platform 1c1b000.usb: irq 28, io mem 0x01c1b000 1636 [ 2.024922] ehci-platform 1c1b000.usb: USB 2.0 started, EHCI 1.00 1637 [ 2.025130] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 1638 [ 2.025137] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 1639 [ 2.025143] usb usb3: Product: EHCI Host Controller 1640 [ 2.025148] usb usb3: Manufacturer: Linux 4.19.38-sunxi ehci_hcd 1641 [ 2.025154] usb usb3: SerialNumber: 1c1b000.usb 1642 [ 2.025678] hub 3-0:1.0: USB hub found 1643 [ 2.025715] hub 3-0:1.0: 1 port detected 1644 [ 2.026484] ehci-platform 1c1c000.usb: EHCI Host Controller 1645 [ 2.026506] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 4 1646 [ 2.026720] ehci-platform 1c1c000.usb: irq 30, io mem 0x01c1c000 1647 [ 2.029005] mmc0: host does not support reading read-only switch, assuming write-enable 1648 [ 2.031999] mmc0: new high speed SDHC card at address aaaa 1649 [ 2.033268] mmcblk0: mmc0:aaaa SL16G 14.8 GiB 1650 [ 2.035621] mmcblk0: p1 1651 [ 2.040933] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 1652 [ 2.041141] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 1653 [ 2.041149] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 1654 [ 2.041154] usb usb4: Product: EHCI Host Controller 1655 [ 2.041160] usb usb4: Manufacturer: Linux 4.19.38-sunxi ehci_hcd 1656 [ 2.041165] usb usb4: SerialNumber: 1c1c000.usb 1657 [ 2.041641] hub 4-0:1.0: USB hub found 1658 [ 2.041679] hub 4-0:1.0: 1 port detected 1659 [ 2.042533] ehci-platform 1c1d000.usb: EHCI Host Controller 1660 [ 2.042558] ehci-platform 1c1d000.usb: new USB bus registered, assigned bus number 5 1661 [ 2.042887] ehci-platform 1c1d000.usb: irq 32, io mem 0x01c1d000 1662 [ 2.056937] ehci-platform 1c1d000.usb: USB 2.0 started, EHCI 1.00 1663 [ 2.057124] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 1664 [ 2.057131] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 1665 [ 2.057136] usb usb5: Product: EHCI Host Controller 1666 [ 2.057142] usb usb5: Manufacturer: Linux 4.19.38-sunxi ehci_hcd 1667 [ 2.057147] usb usb5: SerialNumber: 1c1d000.usb 1668 [ 2.057590] hub 5-0:1.0: USB hub found 1669 [ 2.057626] hub 5-0:1.0: 1 port detected 1670 [ 2.058336] ohci-platform 1c1b400.usb: Generic Platform OHCI controller 1671 [ 2.058358] ohci-platform 1c1b400.usb: new USB bus registered, assigned bus number 6 1672 [ 2.058517] ohci-platform 1c1b400.usb: irq 29, io mem 0x01c1b400 1673 [ 2.121112] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19 1674 [ 2.121119] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 1675 [ 2.121125] usb usb6: Product: Generic Platform OHCI controller 1676 [ 2.121130] usb usb6: Manufacturer: Linux 4.19.38-sunxi ohci_hcd 1677 [ 2.121135] usb usb6: SerialNumber: 1c1b400.usb 1678 [ 2.121573] hub 6-0:1.0: USB hub found 1679 [ 2.121608] hub 6-0:1.0: 1 port detected 1680 [ 2.122279] ohci-platform 1c1c400.usb: Generic Platform OHCI controller 1681 [ 2.122299] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 7 1682 [ 2.122443] ohci-platform 1c1c400.usb: irq 31, io mem 0x01c1c400 1683 [ 2.185103] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19 1684 [ 2.185110] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 1685 [ 2.185116] usb usb7: Product: Generic Platform OHCI controller 1686 [ 2.185121] usb usb7: Manufacturer: Linux 4.19.38-sunxi ohci_hcd 1687 [ 2.185126] usb usb7: SerialNumber: 1c1c400.usb 1688 [ 2.185557] hub 7-0:1.0: USB hub found 1689 [ 2.185595] hub 7-0:1.0: 1 port detected 1690 [ 2.186273] ohci-platform 1c1d400.usb: Generic Platform OHCI controller 1691 [ 2.186292] ohci-platform 1c1d400.usb: new USB bus registered, assigned bus number 8 1692 [ 2.186475] ohci-platform 1c1d400.usb: irq 33, io mem 0x01c1d400 1693 [ 2.249092] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19 1694 [ 2.249101] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1 1695 [ 2.249106] usb usb8: Product: Generic Platform OHCI controller 1696 [ 2.249112] usb usb8: Manufacturer: Linux 4.19.38-sunxi ohci_hcd 1697 [ 2.249117] usb usb8: SerialNumber: 1c1d400.usb 1698 [ 2.249565] hub 8-0:1.0: USB hub found 1699 [ 2.249599] hub 8-0:1.0: 1 port detected 1700 [ 2.250323] usb_phy_generic usb_phy_generic.2.auto: usb_phy_generic.2.auto supply vcc not found, using dummy regulator 1701 [ 2.250387] usb_phy_generic usb_phy_generic.2.auto: Linked as a consumer to regulator.0 1702 [ 2.250684] musb-hdrc musb-hdrc.3.auto: MUSB HDRC host driver 1703 [ 2.250694] musb-hdrc musb-hdrc.3.auto: new USB bus registered, assigned bus number 9 1704 [ 2.250922] usb usb9: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 1705 [ 2.250929] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1 1706 [ 2.250935] usb usb9: Product: MUSB HDRC host driver 1707 [ 2.250940] usb usb9: Manufacturer: Linux 4.19.38-sunxi musb-hcd 1708 [ 2.250945] usb usb9: SerialNumber: musb-hdrc.3.auto 1709 [ 2.251353] hub 9-0:1.0: USB hub found 1710 [ 2.251393] hub 9-0:1.0: 1 port detected 1711 [ 2.252352] sun6i-rtc 1f00000.rtc: setting system clock to 1970-01-01 00:00:16 UTC (16) 1712 [ 2.252539] of_cfs_init 1713 [ 2.252640] of_cfs_init: OK 1714 [ 2.252789] vcc3v0: disabling 1715 [ 2.252795] vcc5v0: disabling 1716 [ 2.252800] usb0-vbus: disabling 1717 [ 2.256103] Freeing unused kernel memory: 1024K 1718 [ 2.273110] Run /init as init process 1719 [ 2.318675] random: systemd-udevd: uninitialized urandom read (16 bytes read) 1720 [ 2.319222] random: systemd-udevd: uninitialized urandom read (16 bytes read) 1721 [ 2.319332] random: systemd-udevd: uninitialized urandom read (16 bytes read) 1722 [ 2.881076] [drm] Cannot find any crtc or sizes 1723 [ 3.368410] random: fast init done 1724 [ 3.395139] EXT4-fs (mmcblk0p1): mounted filesystem with writeback data mode. Opts: (null) 1725 [ 3.864166] systemd[1]: System time before build time, advancing clock. 1726 [ 3.910168] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN) 1727 [ 3.910663] systemd[1]: Detected architecture arm. 1728 [ 3.915039] systemd[1]: Set hostname to <orangepipc>. 1729 [ 4.273938] systemd[1]: Listening on udev Kernel Socket. 1730 [ 4.274858] systemd[1]: Listening on Journal Socket. 1731 [ 4.275366] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. 1732 [ 4.275990] systemd[1]: Listening on Journal Audit Socket. 1733 [ 4.276355] systemd[1]: Listening on fsck to fsckd communication Socket. 1734 [ 4.276709] systemd[1]: Listening on Journal Socket (/dev/log). 1735 [ 4.277805] systemd[1]: Created slice User and Session Slice. 1736 [ 4.441925] EXT4-fs (mmcblk0p1): re-mounted. Opts: commit=600,errors=remount-ro 1737 [ 4.694642] systemd-journald[220]: Received request to flush runtime journal from PID 1 1738 [ 5.158977] cpu cpu0: Linked as a consumer to regulator.5 1739 [ 5.159176] cpu cpu0: Dropping the link to regulator.5 1740 [ 5.159431] cpu cpu0: Linked as a consumer to regulator.5 1741 [ 5.160854] input: r_gpio_keys as /devices/platform/r_gpio_keys/input/input0 1742 [ 5.323633] sun8i_ths 1c25000.thermal-sensor: no memory resources defined 1743 [ 5.323666] sun8i_ths: probe of 1c25000.thermal-sensor failed with error -22 1744 [ 5.392640] Registered IR keymap rc-empty 1745 [ 5.392767] rc rc0: sunxi-ir as /devices/platform/soc/1f02000.ir/rc/rc0 1746 [ 5.392967] input: sunxi-ir as /devices/platform/soc/1f02000.ir/rc/rc0/input1 1747 [ 5.394149] rc rc0: lirc_dev: driver sunxi-ir registered at minor = 0, raw IR receiver, no transmitter 1748 [ 5.396180] sunxi-ir 1f02000.ir: initialized sunXi IR driver 1749 [ 5.396355] thermal thermal_zone0: failed to read out thermal zone (-110) 1750 [ 5.418284] sun4i-codec 1c22c00.codec: ASoC: codec-analog@1f015c0 not registered 1751 [ 5.418298] sun4i-codec 1c22c00.codec: Failed to register our card 1752 [ 5.433598] sun4i-codec 1c22c00.codec: ASoC: Failed to create component debugfs directory 1753 [ 5.439954] sun4i-codec 1c22c00.codec: Codec <-> 1c22c00.codec mapping ok 1754 [ 5.445995] lima 1c40000.gpu: bus rate = 200000000 1755 [ 5.446007] lima 1c40000.gpu: mod rate = 384000000 1756 [ 5.452312] [TTM] Zone kernel: Available graphics memory: 380458 kiB 1757 [ 5.452321] [TTM] Zone highmem: Available graphics memory: 511524 kiB 1758 [ 5.452324] [TTM] Initializing pool allocator 1759 [ 5.453082] lima 1c40000.gpu: gp - mali400 version major 1 minor 1 1760 [ 5.453146] lima 1c40000.gpu: pp0 - mali400 version major 1 minor 1 1761 [ 5.453188] lima 1c40000.gpu: pp1 - mali400 version major 1 minor 1 1762 [ 5.453223] lima 1c40000.gpu: l2 cache 64K, 4-way, 64byte cache line, 64bit external bus 1763 [ 5.454622] [drm] Initialized lima 1.0.0 20170325 for 1c40000.gpu on minor 1 1764 [ 5.532984] zram: Added device: zram0 1765 [ 5.541161] zram: Added device: zram1 1766 [ 5.541768] zram: Added device: zram2 1767 [ 5.611890] zram1: detected capacity change from 0 to 523800576 1768 [ 5.677549] Adding 511520k swap on /dev/zram1. Priority:5 extents:1 across:511520k SSFS 1769 [ 5.823413] zram0: detected capacity change from 0 to 52428800 1770 [ 6.494335] EXT4-fs (zram0): mounted filesystem without journal. Opts: discard 1771 [ 6.531270] random: crng init done 1772 [ 6.531283] random: 7 urandom warning(s) missed due to ratelimiting 1773 [ 9.729911] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready 1774 [ 9.731361] Generic PHY 0.1:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0.1:01, irq=POLL) 1775 [ 9.733629] dwmac-sun8i 1c30000.ethernet eth0: No Safety Features support found 1776 [ 9.733647] dwmac-sun8i 1c30000.ethernet eth0: No MAC Management Counters available 1777 [ 9.733656] dwmac-sun8i 1c30000.ethernet eth0: PTP not supported by HW 1778 [ 9.734086] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready 1779 [ 12.797436] dwmac-sun8i 1c30000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx 1780 [ 12.797477] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready 1781 [ 4029.059023] dwmac-sun8i 1c30000.ethernet eth0: Link is Down 1782 [ 4031.107229] dwmac-sun8i 1c30000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx 1783 1784 1785 vm.admin_reserve_kbytes = 8192 1786 vm.block_dump = 0 1787 vm.compact_unevictable_allowed = 1 1788 vm.dirty_background_bytes = 0 1789 vm.dirty_background_ratio = 10 1790 vm.dirty_bytes = 0 1791 vm.dirty_expire_centisecs = 3000 1792 vm.dirty_ratio = 20 1793 vm.dirty_writeback_centisecs = 500 1794 vm.dirtytime_expire_seconds = 43200 1795 vm.drop_caches = 0 1796 vm.extfrag_threshold = 500 1797 vm.highmem_is_dirtyable = 0 1798 vm.laptop_mode = 0 1799 vm.legacy_va_layout = 0 1800 vm.lowmem_reserve_ratio = 32 0 0 1801 vm.max_map_count = 65530 1802 vm.min_free_kbytes = 3475 1803 vm.mmap_min_addr = 4096 1804 vm.mmap_rnd_bits = 8 1805 vm.oom_dump_tasks = 1 1806 vm.oom_kill_allocating_task = 0 1807 vm.overcommit_kbytes = 0 1808 vm.overcommit_memory = 0 1809 vm.overcommit_ratio = 50 1810 vm.page-cluster = 0 1811 vm.panic_on_oom = 0 1812 vm.percpu_pagelist_fraction = 0 1813 vm.stat_interval = 1 1814 vm.swappiness = 100 1815 vm.user_reserve_kbytes = 31604 1816 vm.vfs_cache_pressure = 100 1817 vm.watermark_scale_factor = 10 1818 1819 ### interrupts: 1820 CPU0 CPU1 CPU2 CPU3 1821 17: 0 0 0 0 GICv2 50 Level timer@1c20c00 1822 18: 0 0 0 0 GICv2 29 Level arch_timer 1823 19: 68115 43835 48835 41702 GICv2 30 Level arch_timer 1824 22: 0 0 0 0 GICv2 82 Level 1c02000.dma-controller 1825 23: 0 0 0 0 GICv2 118 Level 1c0c000.lcd-controller 1826 24: 66636 0 0 0 GICv2 92 Level sunxi-mmc 1827 25: 0 0 0 0 GICv2 103 Level musb-hdrc.3.auto 1828 26: 0 0 0 0 GICv2 104 Level ehci_hcd:usb1 1829 27: 0 0 0 0 GICv2 105 Level ohci_hcd:usb2 1830 28: 0 0 0 0 GICv2 106 Level ehci_hcd:usb3 1831 29: 0 0 0 0 GICv2 107 Level ohci_hcd:usb6 1832 30: 0 0 0 0 GICv2 108 Level ehci_hcd:usb4 1833 31: 0 0 0 0 GICv2 109 Level ohci_hcd:usb7 1834 32: 0 0 0 0 GICv2 110 Level ehci_hcd:usb5 1835 33: 0 0 0 0 GICv2 111 Level ohci_hcd:usb8 1836 36: 49427 0 0 0 GICv2 63 Level 1c25000.thermal-sensor 1837 38: 2945 0 0 0 GICv2 114 Level eth0 1838 42: 10 0 0 0 GICv2 32 Level ttyS0 1839 43: 0 0 0 0 GICv2 120 Level 1ee0000.hdmi 1840 44: 0 0 0 0 GICv2 72 Level 1f00000.rtc 1841 46: 58 0 0 0 GICv2 69 Level sunxi-ir 1842 47: 2936 0 0 0 GICv2 76 Level mv64xxx_i2c 1843 49: 0 0 0 0 GICv2 129 Level gp 1844 50: 0 0 0 0 GICv2 130 Level gpmmu 1845 51: 0 0 0 0 GICv2 131 Level pp0 1846 52: 0 0 0 0 GICv2 132 Level ppmmu0 1847 53: 0 0 0 0 GICv2 134 Level pp1 1848 54: 0 0 0 0 GICv2 135 Level ppmmu1 1849 100: 1 0 0 0 sunxi_pio_edge 44 Edge usb0-id-det 1850 123: 1 0 0 0 sunxi_pio_edge 3 Edge sw4 1851 IPI0: 0 0 0 0 CPU wakeup interrupts 1852 IPI1: 0 0 0 0 Timer broadcast interrupts 1853 IPI2: 7408 13372 17391 10994 Rescheduling interrupts 1854 IPI3: 13 14 11 14 Function call interrupts 1855 IPI4: 0 0 0 0 CPU stop interrupts 1856 IPI5: 12432 1644 2422 1860 IRQ work interrupts 1857 IPI6: 0 0 0 0 completion interrupts 1858 Err: 0 Please upload the whole output above to an online pasteboard service and provide the URL in the forum where you have been asked for this. pi@orangepipc:~$ Hope this helps. i don't know what to do next. Thanks for the reply Link to comment Share on other sites More sharing options...
guidol Posted June 8, 2019 Share Posted June 8, 2019 2 hours ago, cam2019 said: literally i'm new to orange pi and as well as here on armbian. like days old. I managed to run and use the usb device in rpi3b+ but was unable to on orange pi. now i know that this is a driver issue. can someone show me how to download and install the driver on my opi pc? I do use the same USB3.0-ethetnet adapter on my devices under armbian and got NO driver issue. Welcome to ARMBIAN 5.73 stable Debian GNU/Linux 9 (stretch) 5.1.0-sunxi package bsp-kernel[5.86] u-boot[5.85] dtb[5.86] firmware[5.83] config[5.88] Linux opi-zero-99 5.1.0-sunxi #5.86 SMP Mon May 13 21:11:09 CEST 2019 armv7l GNU/Linux [1399909.295651] usb 5-1: new high-speed USB device number 2 using ehci-platform [1399909.455662] usb 5-1: New USB device found, idVendor=0bda, idProduct=8153, bcdDevice=30.00 [1399909.455734] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=6 [1399909.455783] usb 5-1: Product: USB 10/100/1000 LAN [1399909.455830] usb 5-1: Manufacturer: Realtek [1399909.455874] usb 5-1: SerialNumber: 000001000000 [1399909.732093] usbcore: registered new interface driver r8152 [1399909.763071] usbcore: registered new interface driver cdc_ether [1399909.867457] usb 5-1: reset high-speed USB device number 2 using ehci-platform [1399910.083109] r8152 5-1:1.0 eth1: v1.09.9 [1399910.174042] r8152 5-1:1.0 enx00e04c68007b: renamed from eth1 Which version of armbian do you use? Maybe your eth1 is also renamed (see dmesg or ifconfig) = Predictable Network Interface Name Maybe you have to switch this off for eth1 as name: http://www.itzgeek.com/how-tos/mini-howtos/change-default-network-name-ens33-to-old-eth0-on-ubuntu-16-04.html sudo nano /etc/default/grub from: GRUB_CMDLINE_LINUX="" to: GRUB_CMDLINE_LINUX="net.ifnames=0 biosdevname=0" sudo grub-mkconfig -o /boot/grub/grub.cfg reboot [EDIT] your code in your dmesg: 413 [ 5.906764] r8152 4-1:1.0 eth1: v1.09.9 414 [ 6.188868] EXT4-fs (zram0): mounted filesystem without journal. Opts: discard 415 [ 6.552250] r8152 4-1:1.0 enx00e04c680046: renamed from eth1 So now configure enx00e04c680046 or disable the predictable network names Test: ifconfig enx00e04c680046 up and then look for the device with ifconfig Link to comment Share on other sites More sharing options...
cam2019 Posted June 8, 2019 Author Share Posted June 8, 2019 I use the latest Armbian_5.83_Orangepipc_Debian_stretch_next_4.19.38.img Link to comment Share on other sites More sharing options...
cam2019 Posted June 8, 2019 Author Share Posted June 8, 2019 this is what i get Spoiler pi@orangepipc:~$ dmesg [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.38-sunxi (root@nightly) (gcc version 7.4.1 20181213 [linaro-7.4-2019.02 revision 56ec6f6b99cc167ff0c2f8e1a2eed33b1edc85d4] (Linaro GCC 7.4-2019.02)) #5.83 SMP Fri May 3 23:33:25 CEST 2019 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=50c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Xunlong Orange Pi PC [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] cma: Reserved 128 MiB at 0x75c00000 [ 0.000000] On node 0 totalpages: 262144 [ 0.000000] Normal zone: 1728 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 196608 pages, LIFO batch:63 [ 0.000000] HighMem zone: 65536 pages, LIFO batch:15 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: Using PSCI v0.1 Function IDs from DT [ 0.000000] random: get_random_bytes called from start_kernel+0x8d/0x3c6 with crng_init=0 [ 0.000000] percpu: Embedded 18 pages/cpu s41548 r8192 d23988 u73728 [ 0.000000] pcpu-alloc: s41548 r8192 d23988 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260416 [ 0.000000] Kernel command line: root=UUID=1b49372a-ea5b-42f6-9e60-036606066891 rootwait rootfstype=ext4 console=ttyS0,115200 console=tty1 hdmi.audio=EDID:0 disp.screen0_output_mode=1920x1080p60 panic=10 consoleblank=0 loglevel=1 ubootpart=5ae5405d-01 ubootsource=mmc usb-storage.quirks=0x2537:0x1066:u,0x2537:0x1068:u sunxi_ve_mem_reserve=0 sunxi_g2d_mem_reserve=0 sunxi_fb_mem_reserve=16 cgroup_enable=memory swapaccount=1 [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] allocated 1048576 bytes of page_ext [ 0.000000] Memory: 886136K/1048576K available (9216K kernel code, 1004K rwdata, 2576K rodata, 1024K init, 331K bss, 31368K reserved, 131072K cma-reserved, 131060K highmem) [ 0.000000] Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf800000 - 0xbfe00000 ( 6 MB) .text : 0x(ptrval) - 0x(ptrval) (10208 kB) .init : 0x(ptrval) - 0x(ptrval) (1024 kB) .data : 0x(ptrval) - 0x(ptrval) (1005 kB) .bss : 0x(ptrval) - 0x(ptrval) ( 332 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] ftrace: allocating 39959 entries in 79 pages [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000014] Switching to timer-based delay loop, resolution 41ns [ 0.000166] Console: colour dummy device 80x30 [ 0.000178] console [tty1] enabled [ 0.000226] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.000236] pid_max: default: 32768 minimum: 301 [ 0.000431] Security Framework initialized [ 0.000440] AppArmor: AppArmor disabled by boot time parameter [ 0.000511] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000520] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.001341] CPU: Testing write buffer coherency: ok [ 0.001749] CPU0: update cpu_capacity 1024 [ 0.001756] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.002235] Setting up static identity map for 0x40100000 - 0x40100054 [ 0.002378] rcu: Hierarchical SRCU implementation. [ 0.003102] smp: Bringing up secondary CPUs ... [ 0.013793] CPU1: update cpu_capacity 1024 [ 0.013799] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.024574] CPU2: update cpu_capacity 1024 [ 0.024580] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.035289] CPU3: update cpu_capacity 1024 [ 0.035294] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.035386] smp: Brought up 1 node, 4 CPUs [ 0.035393] SMP: Total of 4 processors activated (192.00 BogoMIPS). [ 0.035397] CPU: All CPU(s) started in HYP mode. [ 0.035399] CPU: Virtualization extensions available. [ 0.036541] devtmpfs: initialized [ 0.043017] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.043268] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.043284] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.047958] xor: measuring software checksum speed [ 0.087250] arm4regs : 1255.000 MB/sec [ 0.127306] 8regs : 748.000 MB/sec [ 0.167366] 32regs : 766.000 MB/sec [ 0.207427] neon : 1270.000 MB/sec [ 0.207431] xor: using function: neon (1270.000 MB/sec) [ 0.207494] pinctrl core: initialized pinctrl subsystem [ 0.208403] NET: Registered protocol family 16 [ 0.211134] DMA: preallocated 2048 KiB pool for atomic coherent allocations [ 0.211625] audit: initializing netlink subsys (disabled) [ 0.211777] audit: type=2000 audit(0.188:1): state=initialized audit_enabled=0 res=1 [ 0.212273] cpuidle: using governor ladder [ 0.212301] cpuidle: using governor menu [ 0.212812] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.212817] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.295927] raid6: int32x1 gen() 189 MB/s [ 0.363858] raid6: int32x1 xor() 160 MB/s [ 0.431888] raid6: int32x2 gen() 255 MB/s [ 0.499955] raid6: int32x2 xor() 194 MB/s [ 0.568098] raid6: int32x4 gen() 258 MB/s [ 0.636219] raid6: int32x4 xor() 193 MB/s [ 0.704222] raid6: int32x8 gen() 247 MB/s [ 0.772446] raid6: int32x8 xor() 172 MB/s [ 0.840484] raid6: neonx1 gen() 495 MB/s [ 0.908528] raid6: neonx1 xor() 460 MB/s [ 0.976670] raid6: neonx2 gen() 664 MB/s [ 1.044736] raid6: neonx2 xor() 594 MB/s [ 1.112873] raid6: neonx4 gen() 798 MB/s [ 1.180930] raid6: neonx4 xor() 669 MB/s [ 1.249017] raid6: neonx8 gen() 716 MB/s [ 1.317142] raid6: neonx8 xor() 606 MB/s [ 1.317145] raid6: using algorithm neonx4 gen() 798 MB/s [ 1.317148] raid6: .... xor() 669 MB/s, rmw enabled [ 1.317152] raid6: using neon recovery algorithm [ 1.318522] SCSI subsystem initialized [ 1.318705] libata version 3.00 loaded. [ 1.318898] usbcore: registered new interface driver usbfs [ 1.318938] usbcore: registered new interface driver hub [ 1.319001] usbcore: registered new device driver usb [ 1.319172] media: Linux media interface: v0.10 [ 1.319200] videodev: Linux video capture interface: v2.00 [ 1.319316] pps_core: LinuxPPS API ver. 1 registered [ 1.319321] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 1.319336] PTP clock support registered [ 1.320915] clocksource: Switched to clocksource arch_sys_counter [ 1.424029] VFS: Disk quotas dquot_6.6.0 [ 1.424105] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.431638] NET: Registered protocol family 2 [ 1.432326] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) [ 1.432354] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 1.432441] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 1.432552] TCP: Hash tables configured (established 8192 bind 8192) [ 1.432663] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 1.432723] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 1.433009] NET: Registered protocol family 1 [ 1.433502] RPC: Registered named UNIX socket transport module. [ 1.433507] RPC: Registered udp transport module. [ 1.433510] RPC: Registered tcp transport module. [ 1.433513] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.433738] Trying to unpack rootfs image as initramfs... [ 1.732189] Freeing initrd memory: 4816K [ 1.733980] Initialise system trusted keyrings [ 1.734199] workingset: timestamp_bits=14 max_order=18 bucket_order=4 [ 1.739825] zbud: loaded [ 1.741967] NFS: Registering the id_resolver key type [ 1.741997] Key type id_resolver registered [ 1.742001] Key type id_legacy registered [ 1.742013] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.742017] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 1.743080] JFS: nTxBlock = 7984, nTxLock = 63876 [ 1.751794] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 1.759265] Key type asymmetric registered [ 1.759274] Asymmetric key parser 'x509' registered [ 1.759333] bounce: pool size: 64 pages [ 1.759410] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 1.759549] io scheduler noop registered [ 1.759553] io scheduler deadline registered [ 1.759749] io scheduler cfq registered (default) [ 1.759755] io scheduler mq-deadline registered [ 1.759759] io scheduler kyber registered [ 1.759884] io scheduler bfq registered [ 1.761028] sun4i-usb-phy 1c19400.phy: Couldn't request ID GPIO [ 1.764991] sun8i-h3-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver [ 1.766487] sun8i-h3-r-pinctrl 1f02c00.pinctrl: initialized sunXi PIO driver [ 1.814770] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled [ 1.816981] console [ttyS0] disabled [ 1.837124] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 42, base_baud = 1500000) is a U6_16550A [ 1.837179] console [ttyS0] enabled [ 1.860495] sun4i-drm display-engine: bound 1100000.mixer (ops 0xc0a85d08) [ 1.860741] sun4i-drm display-engine: bound 1c0c000.lcd-controller (ops 0xc0a83454) [ 1.860794] sun8i-dw-hdmi 1ee0000.hdmi: 1ee0000.hdmi supply hvcc not found, using dummy regulator [ 1.860850] sun8i-dw-hdmi 1ee0000.hdmi: Linked as a consumer to regulator.0 [ 1.861684] sun8i-dw-hdmi 1ee0000.hdmi: Detected HDMI TX controller v1.32a with HDCP (sun8i_dw_hdmi_phy) [ 1.862031] sun8i-dw-hdmi 1ee0000.hdmi: registered DesignWare HDMI I2C bus driver [ 1.862262] sun4i-drm display-engine: bound 1ee0000.hdmi (ops 0xc0a8578c) [ 1.862267] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 1.862271] [drm] No driver support for vblank timestamp query. [ 1.862334] [drm] Cannot find any crtc or sizes [ 1.862784] [drm] Initialized sun4i-drm 1.0.0 20150629 for display-engine on minor 0 [ 1.865762] brd: module loaded [ 1.871120] loop: module loaded [ 1.873417] libphy: Fixed MDIO Bus: probed [ 1.873950] dwmac-sun8i 1c30000.ethernet: PTP uses main clock [ 1.873986] dwmac-sun8i 1c30000.ethernet: No regulator found [ 1.874280] dwmac-sun8i 1c30000.ethernet: Current syscon value is not the default 148000 (expect 58000) [ 1.874297] dwmac-sun8i 1c30000.ethernet: No HW DMA feature register supported [ 1.874303] dwmac-sun8i 1c30000.ethernet: RX Checksum Offload Engine supported [ 1.874308] dwmac-sun8i 1c30000.ethernet: COE Type 2 [ 1.874314] dwmac-sun8i 1c30000.ethernet: TX Checksum insertion supported [ 1.874320] dwmac-sun8i 1c30000.ethernet: Normal descriptors [ 1.874325] dwmac-sun8i 1c30000.ethernet: Chain mode enabled [ 1.874458] libphy: stmmac: probed [ 1.874894] dwmac-sun8i 1c30000.ethernet: Found internal PHY node [ 1.874979] libphy: mdio_mux: probed [ 1.874998] dwmac-sun8i 1c30000.ethernet: Switch mux to internal PHY [ 1.875005] dwmac-sun8i 1c30000.ethernet: Powering internal PHY [ 1.879722] libphy: mdio_mux: probed [ 1.880623] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.880628] ehci-platform: EHCI generic platform driver [ 1.880808] ehci-platform 1c1a000.usb: EHCI Host Controller [ 1.880835] ehci-platform 1c1a000.usb: new USB bus registered, assigned bus number 1 [ 1.881582] ehci-platform 1c1a000.usb: irq 26, io mem 0x01c1a000 [ 1.896918] ehci-platform 1c1a000.usb: USB 2.0 started, EHCI 1.00 [ 1.897205] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 [ 1.897212] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.897218] usb usb1: Product: EHCI Host Controller [ 1.897224] usb usb1: Manufacturer: Linux 4.19.38-sunxi ehci_hcd [ 1.897229] usb usb1: SerialNumber: 1c1a000.usb [ 1.897794] hub 1-0:1.0: USB hub found [ 1.897839] hub 1-0:1.0: 1 port detected [ 1.898649] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.898673] ohci-platform: OHCI generic platform driver [ 1.898823] ohci-platform 1c1a400.usb: Generic Platform OHCI controller [ 1.898844] ohci-platform 1c1a400.usb: new USB bus registered, assigned bus number 2 [ 1.899003] ohci-platform 1c1a400.usb: irq 27, io mem 0x01c1a400 [ 1.961151] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19 [ 1.961158] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.961164] usb usb2: Product: Generic Platform OHCI controller [ 1.961169] usb usb2: Manufacturer: Linux 4.19.38-sunxi ohci_hcd [ 1.961175] usb usb2: SerialNumber: 1c1a400.usb [ 1.961611] hub 2-0:1.0: USB hub found [ 1.961652] hub 2-0:1.0: 1 port detected [ 1.962784] usbcore: registered new interface driver usb-storage [ 1.963508] sun6i-rtc 1f00000.rtc: rtc core: registered rtc-sun6i as rtc0 [ 1.963515] sun6i-rtc 1f00000.rtc: RTC enabled [ 1.963715] i2c /dev entries driver [ 1.965710] sunxi-wdt 1c20ca0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) [ 1.966465] sunxi-mmc 1c0f000.mmc: Linked as a consumer to regulator.2 [ 1.966951] sunxi-mmc 1c0f000.mmc: Got CD GPIO [ 1.967222] ledtrig-cpu: registered to indicate activity on CPUs [ 1.967295] hidraw: raw HID events driver (C) Jiri Kosina [ 1.967404] usbcore: registered new interface driver usbhid [ 1.967407] usbhid: USB HID core driver [ 1.973490] Initializing XFRM netlink socket [ 1.974156] NET: Registered protocol family 10 [ 1.988710] Segment Routing with IPv6 [ 1.988806] NET: Registered protocol family 17 [ 1.988831] NET: Registered protocol family 15 [ 1.988889] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 1.988993] 8021q: 802.1Q VLAN Support v1.8 [ 1.989267] Key type dns_resolver registered [ 1.989705] Registering SWP/SWPB emulation handler [ 1.990242] registered taskstats version 1 [ 1.990247] Loading compiled-in X.509 certificates [ 1.990336] zswap: loaded using pool lzo/zbud [ 1.992077] Btrfs loaded, crc32c=crc32c-generic [ 1.992280] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB [ 1.999103] Key type encrypted registered [ 2.007857] sun4i-usb-phy 1c19400.phy: Linked as a consumer to regulator.4 [ 2.008802] ehci-platform 1c1b000.usb: EHCI Host Controller [ 2.008834] ehci-platform 1c1b000.usb: new USB bus registered, assigned bus number 3 [ 2.009397] ehci-platform 1c1b000.usb: irq 28, io mem 0x01c1b000 [ 2.024922] ehci-platform 1c1b000.usb: USB 2.0 started, EHCI 1.00 [ 2.025130] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 [ 2.025137] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.025143] usb usb3: Product: EHCI Host Controller [ 2.025148] usb usb3: Manufacturer: Linux 4.19.38-sunxi ehci_hcd [ 2.025154] usb usb3: SerialNumber: 1c1b000.usb [ 2.025678] hub 3-0:1.0: USB hub found [ 2.025715] hub 3-0:1.0: 1 port detected [ 2.026484] ehci-platform 1c1c000.usb: EHCI Host Controller [ 2.026506] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 4 [ 2.026720] ehci-platform 1c1c000.usb: irq 30, io mem 0x01c1c000 [ 2.029005] mmc0: host does not support reading read-only switch, assuming write-enable [ 2.031999] mmc0: new high speed SDHC card at address aaaa [ 2.033268] mmcblk0: mmc0:aaaa SL16G 14.8 GiB [ 2.035621] mmcblk0: p1 [ 2.040933] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 2.041141] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 [ 2.041149] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.041154] usb usb4: Product: EHCI Host Controller [ 2.041160] usb usb4: Manufacturer: Linux 4.19.38-sunxi ehci_hcd [ 2.041165] usb usb4: SerialNumber: 1c1c000.usb [ 2.041641] hub 4-0:1.0: USB hub found [ 2.041679] hub 4-0:1.0: 1 port detected [ 2.042533] ehci-platform 1c1d000.usb: EHCI Host Controller [ 2.042558] ehci-platform 1c1d000.usb: new USB bus registered, assigned bus number 5 [ 2.042887] ehci-platform 1c1d000.usb: irq 32, io mem 0x01c1d000 [ 2.056937] ehci-platform 1c1d000.usb: USB 2.0 started, EHCI 1.00 [ 2.057124] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 [ 2.057131] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.057136] usb usb5: Product: EHCI Host Controller [ 2.057142] usb usb5: Manufacturer: Linux 4.19.38-sunxi ehci_hcd [ 2.057147] usb usb5: SerialNumber: 1c1d000.usb [ 2.057590] hub 5-0:1.0: USB hub found [ 2.057626] hub 5-0:1.0: 1 port detected [ 2.058336] ohci-platform 1c1b400.usb: Generic Platform OHCI controller [ 2.058358] ohci-platform 1c1b400.usb: new USB bus registered, assigned bus number 6 [ 2.058517] ohci-platform 1c1b400.usb: irq 29, io mem 0x01c1b400 [ 2.121112] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19 [ 2.121119] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.121125] usb usb6: Product: Generic Platform OHCI controller [ 2.121130] usb usb6: Manufacturer: Linux 4.19.38-sunxi ohci_hcd [ 2.121135] usb usb6: SerialNumber: 1c1b400.usb [ 2.121573] hub 6-0:1.0: USB hub found [ 2.121608] hub 6-0:1.0: 1 port detected [ 2.122279] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 2.122299] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 7 [ 2.122443] ohci-platform 1c1c400.usb: irq 31, io mem 0x01c1c400 [ 2.185103] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19 [ 2.185110] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.185116] usb usb7: Product: Generic Platform OHCI controller [ 2.185121] usb usb7: Manufacturer: Linux 4.19.38-sunxi ohci_hcd [ 2.185126] usb usb7: SerialNumber: 1c1c400.usb [ 2.185557] hub 7-0:1.0: USB hub found [ 2.185595] hub 7-0:1.0: 1 port detected [ 2.186273] ohci-platform 1c1d400.usb: Generic Platform OHCI controller [ 2.186292] ohci-platform 1c1d400.usb: new USB bus registered, assigned bus number 8 [ 2.186475] ohci-platform 1c1d400.usb: irq 33, io mem 0x01c1d400 [ 2.249092] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19 [ 2.249101] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.249106] usb usb8: Product: Generic Platform OHCI controller [ 2.249112] usb usb8: Manufacturer: Linux 4.19.38-sunxi ohci_hcd [ 2.249117] usb usb8: SerialNumber: 1c1d400.usb [ 2.249565] hub 8-0:1.0: USB hub found [ 2.249599] hub 8-0:1.0: 1 port detected [ 2.250323] usb_phy_generic usb_phy_generic.2.auto: usb_phy_generic.2.auto supply vcc not found, using dummy regulator [ 2.250387] usb_phy_generic usb_phy_generic.2.auto: Linked as a consumer to regulator.0 [ 2.250684] musb-hdrc musb-hdrc.3.auto: MUSB HDRC host driver [ 2.250694] musb-hdrc musb-hdrc.3.auto: new USB bus registered, assigned bus number 9 [ 2.250922] usb usb9: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 [ 2.250929] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.250935] usb usb9: Product: MUSB HDRC host driver [ 2.250940] usb usb9: Manufacturer: Linux 4.19.38-sunxi musb-hcd [ 2.250945] usb usb9: SerialNumber: musb-hdrc.3.auto [ 2.251353] hub 9-0:1.0: USB hub found [ 2.251393] hub 9-0:1.0: 1 port detected [ 2.252352] sun6i-rtc 1f00000.rtc: setting system clock to 1970-01-01 00:00:16 UTC (16) [ 2.252539] of_cfs_init [ 2.252640] of_cfs_init: OK [ 2.252789] vcc3v0: disabling [ 2.252795] vcc5v0: disabling [ 2.252800] usb0-vbus: disabling [ 2.256103] Freeing unused kernel memory: 1024K [ 2.273110] Run /init as init process [ 2.318675] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 2.319222] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 2.319332] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 2.881076] [drm] Cannot find any crtc or sizes [ 3.368410] random: fast init done [ 3.395139] EXT4-fs (mmcblk0p1): mounted filesystem with writeback data mode. Opts: (null) [ 3.864166] systemd[1]: System time before build time, advancing clock. [ 3.910168] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN) [ 3.910663] systemd[1]: Detected architecture arm. [ 3.915039] systemd[1]: Set hostname to <orangepipc>. [ 4.273938] systemd[1]: Listening on udev Kernel Socket. [ 4.274858] systemd[1]: Listening on Journal Socket. [ 4.275366] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ 4.275990] systemd[1]: Listening on Journal Audit Socket. [ 4.276355] systemd[1]: Listening on fsck to fsckd communication Socket. [ 4.276709] systemd[1]: Listening on Journal Socket (/dev/log). [ 4.277805] systemd[1]: Created slice User and Session Slice. [ 4.441925] EXT4-fs (mmcblk0p1): re-mounted. Opts: commit=600,errors=remount-ro [ 4.694642] systemd-journald[220]: Received request to flush runtime journal from PID 1 [ 5.158977] cpu cpu0: Linked as a consumer to regulator.5 [ 5.159176] cpu cpu0: Dropping the link to regulator.5 [ 5.159431] cpu cpu0: Linked as a consumer to regulator.5 [ 5.160854] input: r_gpio_keys as /devices/platform/r_gpio_keys/input/input0 [ 5.323633] sun8i_ths 1c25000.thermal-sensor: no memory resources defined [ 5.323666] sun8i_ths: probe of 1c25000.thermal-sensor failed with error -22 [ 5.392640] Registered IR keymap rc-empty [ 5.392767] rc rc0: sunxi-ir as /devices/platform/soc/1f02000.ir/rc/rc0 [ 5.392967] input: sunxi-ir as /devices/platform/soc/1f02000.ir/rc/rc0/input1 [ 5.394149] rc rc0: lirc_dev: driver sunxi-ir registered at minor = 0, raw IR receiver, no transmitter [ 5.396180] sunxi-ir 1f02000.ir: initialized sunXi IR driver [ 5.396355] thermal thermal_zone0: failed to read out thermal zone (-110) [ 5.418284] sun4i-codec 1c22c00.codec: ASoC: codec-analog@1f015c0 not registered [ 5.418298] sun4i-codec 1c22c00.codec: Failed to register our card [ 5.433598] sun4i-codec 1c22c00.codec: ASoC: Failed to create component debugfs directory [ 5.439954] sun4i-codec 1c22c00.codec: Codec <-> 1c22c00.codec mapping ok [ 5.445995] lima 1c40000.gpu: bus rate = 200000000 [ 5.446007] lima 1c40000.gpu: mod rate = 384000000 [ 5.452312] [TTM] Zone kernel: Available graphics memory: 380458 kiB [ 5.452321] [TTM] Zone highmem: Available graphics memory: 511524 kiB [ 5.452324] [TTM] Initializing pool allocator [ 5.453082] lima 1c40000.gpu: gp - mali400 version major 1 minor 1 [ 5.453146] lima 1c40000.gpu: pp0 - mali400 version major 1 minor 1 [ 5.453188] lima 1c40000.gpu: pp1 - mali400 version major 1 minor 1 [ 5.453223] lima 1c40000.gpu: l2 cache 64K, 4-way, 64byte cache line, 64bit external bus [ 5.454622] [drm] Initialized lima 1.0.0 20170325 for 1c40000.gpu on minor 1 [ 5.532984] zram: Added device: zram0 [ 5.541161] zram: Added device: zram1 [ 5.541768] zram: Added device: zram2 [ 5.611890] zram1: detected capacity change from 0 to 523800576 [ 5.677549] Adding 511520k swap on /dev/zram1. Priority:5 extents:1 across:511520k SSFS [ 5.823413] zram0: detected capacity change from 0 to 52428800 [ 6.494335] EXT4-fs (zram0): mounted filesystem without journal. Opts: discard [ 6.531270] random: crng init done [ 6.531283] random: 7 urandom warning(s) missed due to ratelimiting [ 9.729911] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 9.731361] Generic PHY 0.1:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0.1:01, irq=POLL) [ 9.733629] dwmac-sun8i 1c30000.ethernet eth0: No Safety Features support found [ 9.733647] dwmac-sun8i 1c30000.ethernet eth0: No MAC Management Counters available [ 9.733656] dwmac-sun8i 1c30000.ethernet eth0: PTP not supported by HW [ 9.734086] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 12.797436] dwmac-sun8i 1c30000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx [ 12.797477] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 4029.059023] dwmac-sun8i 1c30000.ethernet eth0: Link is Down [ 4031.107229] dwmac-sun8i 1c30000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx pi@orangepipc:~$ Link to comment Share on other sites More sharing options...
Igor Posted June 8, 2019 Share Posted June 8, 2019 7 minutes ago, cam2019 said: I use the latest Armbian_5.83_Orangepipc_Debian_stretch_next_4.19.38.img Its not recognised at all - like it was not attached. Try connecting it via some powered USB hub. Edit: Next time use link generated by armbianmonitor -u ... to reduce those walls of text. Link to comment Share on other sites More sharing options...
cam2019 Posted June 8, 2019 Author Share Posted June 8, 2019 3 minutes ago, Igor said: Its not recognised at all - like it was not attached. Try connecting it via some powered USB hub. could it be a power supply issue? the usb adapter works fine under windows so i'm sure its working fine. Link to comment Share on other sites More sharing options...
Igor Posted June 8, 2019 Share Posted June 8, 2019 Just now, cam2019 said: could it be a power supply ssue? Surely possible. What about other USB (especially USB3) devices? Do they work? Link to comment Share on other sites More sharing options...
guidol Posted June 8, 2019 Share Posted June 8, 2019 6 minutes ago, Igor said: Its not recognised at all - like it was not attached. Try connecting it via some powered USB hub. in his first dmesg it was recognized: 388 [ 5.571663] usbcore: registered new interface driver r8152 413 [ 5.906764] r8152 4-1:1.0 eth1: v1.09.9 414 [ 6.188868] EXT4-fs (zram0): mounted filesystem without journal. Opts: discard 415 [ 6.552250] r8152 4-1:1.0 enx00e04c680046: renamed from eth1 but not in the second one. @cam2019 did you use another USB-Port? Maybe that has to be enabled in armbian-config -> system -> hardware ? 1 Link to comment Share on other sites More sharing options...
cam2019 Posted June 8, 2019 Author Share Posted June 8, 2019 im not sure i only have these usb gigabit for usb 3.0 Link to comment Share on other sites More sharing options...
Igor Posted June 8, 2019 Share Posted June 8, 2019 1 minute ago, guidol said: but not in the second one. Than its almost 100% power related problem. Not an Armbian problem. Link to comment Share on other sites More sharing options...
cam2019 Posted June 8, 2019 Author Share Posted June 8, 2019 3 minutes ago, guidol said: in his first dmesg it was recognized: 388 [ 5.571663] usbcore: registered new interface driver r8152 413 [ 5.906764] r8152 4-1:1.0 eth1: v1.09.9 414 [ 6.188868] EXT4-fs (zram0): mounted filesystem without journal. Opts: discard 415 [ 6.552250] r8152 4-1:1.0 enx00e04c680046: renamed from eth1 but not in the second one. @cam2019 did you use another USB-Port? Maybe hat has to be enabled in armbian-config -> system -> hardware ? its the only usb device that is connected at the moment and yes i tried using all the 3 ports still got no eth1 Link to comment Share on other sites More sharing options...
guidol Posted June 8, 2019 Share Posted June 8, 2019 14 minutes ago, cam2019 said: I use the latest Armbian_5.83_Orangepipc_Debian_stretch_next_4.19.38.img with this version you shouldnt have a driver issue - like you could see in your first dmesg log Link to comment Share on other sites More sharing options...
guidol Posted June 8, 2019 Share Posted June 8, 2019 Just now, cam2019 said: its the only usb device that is connected at the moment at the same USB-Port? I have also a OPi PC and he has 3 USB-Ports Link to comment Share on other sites More sharing options...
cam2019 Posted June 8, 2019 Author Share Posted June 8, 2019 ahh i see. i will change the power supply and will get back to you asap thanks for the very fast replies Link to comment Share on other sites More sharing options...
cam2019 Posted June 8, 2019 Author Share Posted June 8, 2019 after changing to 3amps 5v psu still i get this Spoiler pi@orangepipc:~$ sudo ifconfig eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.2.119 netmask 255.255.255.0 broadcast 192.168.2.255 inet6 fe80::ecc5:4572:5bee:8fcd prefixlen 64 scopeid 0x20<link> ether 02:81:41:c6:e0:a6 txqueuelen 1000 (Ethernet) RX packets 300 bytes 32126 (31.3 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 211 bytes 28011 (27.3 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 38 lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 inet6 ::1 prefixlen 128 scopeid 0x10<host> loop txqueuelen 1000 (Local Loopback) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 pi@orangepipc:~$ pi@orangepipc:~$ sudo dmesg [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.38-sunxi (root@nightly) (gcc version 7.4.1 201 81213 [linaro-7.4-2019.02 revision 56ec6f6b99cc167ff0c2f8e1a2eed33b1edc85d4] (Li naro GCC 7.4-2019.02)) #5.83 SMP Fri May 3 23:33:25 CEST 2019 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=50c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instructio n cache [ 0.000000] OF: fdt: Machine model: Xunlong Orange Pi PC [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] cma: Reserved 128 MiB at 0x75c00000 [ 0.000000] On node 0 totalpages: 262144 [ 0.000000] Normal zone: 1728 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 196608 pages, LIFO batch:63 [ 0.000000] HighMem zone: 65536 pages, LIFO batch:15 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: Using PSCI v0.1 Function IDs from DT [ 0.000000] random: get_random_bytes called from start_kernel+0x8d/0x3c6 with crng_init=0 [ 0.000000] percpu: Embedded 18 pages/cpu s41548 r8192 d23988 u73728 [ 0.000000] pcpu-alloc: s41548 r8192 d23988 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260416 [ 0.000000] Kernel command line: root=UUID=1b49372a-ea5b-42f6-9e60-0366060668 91 rootwait rootfstype=ext4 console=ttyS0,115200 console=tty1 hdmi.audio=EDID:0 disp.screen0_output_mode=1920x1080p60 panic=10 consoleblank=0 loglevel=1 ubootpa rt=5ae5405d-01 ubootsource=mmc usb-storage.quirks=0x2537:0x1066:u,0x2537:0x1068: u sunxi_ve_mem_reserve=0 sunxi_g2d_mem_reserve=0 sunxi_fb_mem_reserve=16 cgrou p_enable=memory swapaccount=1 [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] allocated 1048576 bytes of page_ext [ 0.000000] Memory: 886136K/1048576K available (9216K kernel code, 1004K rwda ta, 2576K rodata, 1024K init, 331K bss, 31368K reserved, 131072K cma-reserved, 1 31060K highmem) [ 0.000000] Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf800000 - 0xbfe00000 ( 6 MB) .text : 0x(ptrval) - 0x(ptrval) (10208 kB) .init : 0x(ptrval) - 0x(ptrval) (1024 kB) .data : 0x(ptrval) - 0x(ptrval) (1005 kB) .bss : 0x(ptrval) - 0x(ptrval) ( 332 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] ftrace: allocating 39959 entries in 79 pages [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_ idle_ns: 79635851949 ns [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 43980 46511097ns [ 0.000014] Switching to timer-based delay loop, resolution 41ns [ 0.000169] Console: colour dummy device 80x30 [ 0.000181] console [tty1] enabled [ 0.000229] Calibrating delay loop (skipped), value calculated using timer fr equency.. 48.00 BogoMIPS (lpj=96000) [ 0.000239] pid_max: default: 32768 minimum: 301 [ 0.000434] Security Framework initialized [ 0.000445] AppArmor: AppArmor disabled by boot time parameter [ 0.000516] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000526] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.001344] CPU: Testing write buffer coherency: ok [ 0.001756] CPU0: update cpu_capacity 1024 [ 0.001763] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.002246] Setting up static identity map for 0x40100000 - 0x40100054 [ 0.002388] rcu: Hierarchical SRCU implementation. [ 0.003104] smp: Bringing up secondary CPUs ... [ 0.013789] CPU1: update cpu_capacity 1024 [ 0.013795] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.024583] CPU2: update cpu_capacity 1024 [ 0.024588] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.035297] CPU3: update cpu_capacity 1024 [ 0.035303] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.035393] smp: Brought up 1 node, 4 CPUs [ 0.035400] SMP: Total of 4 processors activated (192.00 BogoMIPS). [ 0.035404] CPU: All CPU(s) started in HYP mode. [ 0.035406] CPU: Virtualization extensions available. [ 0.036551] devtmpfs: initialized [ 0.043025] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.043271] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 7645041785100000 ns [ 0.043287] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.047961] xor: measuring software checksum speed [ 0.087258] arm4regs : 1255.000 MB/sec [ 0.127314] 8regs : 748.000 MB/sec [ 0.167375] 32regs : 766.000 MB/sec [ 0.207436] neon : 1270.000 MB/sec [ 0.207440] xor: using function: neon (1270.000 MB/sec) [ 0.207504] pinctrl core: initialized pinctrl subsystem [ 0.208412] NET: Registered protocol family 16 [ 0.210789] DMA: preallocated 2048 KiB pool for atomic coherent allocations [ 0.211260] audit: initializing netlink subsys (disabled) [ 0.211421] audit: type=2000 audit(0.184:1): state=initialized audit_enabled= 0 res=1 [ 0.211941] cpuidle: using governor ladder [ 0.211971] cpuidle: using governor menu [ 0.212487] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.212491] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.295950] raid6: int32x1 gen() 189 MB/s [ 0.363905] raid6: int32x1 xor() 160 MB/s [ 0.431904] raid6: int32x2 gen() 255 MB/s [ 0.499955] raid6: int32x2 xor() 194 MB/s [ 0.568116] raid6: int32x4 gen() 258 MB/s [ 0.636222] raid6: int32x4 xor() 193 MB/s [ 0.704244] raid6: int32x8 gen() 247 MB/s [ 0.772457] raid6: int32x8 xor() 172 MB/s [ 0.840498] raid6: neonx1 gen() 495 MB/s [ 0.908538] raid6: neonx1 xor() 460 MB/s [ 0.976686] raid6: neonx2 gen() 664 MB/s [ 1.044749] raid6: neonx2 xor() 594 MB/s [ 1.112884] raid6: neonx4 gen() 798 MB/s [ 1.180940] raid6: neonx4 xor() 669 MB/s [ 1.249026] raid6: neonx8 gen() 716 MB/s [ 1.317132] raid6: neonx8 xor() 606 MB/s [ 1.317136] raid6: using algorithm neonx4 gen() 798 MB/s [ 1.317139] raid6: .... xor() 669 MB/s, rmw enabled [ 1.317142] raid6: using neon recovery algorithm [ 1.318495] SCSI subsystem initialized [ 1.318677] libata version 3.00 loaded. [ 1.318869] usbcore: registered new interface driver usbfs [ 1.318907] usbcore: registered new interface driver hub [ 1.318968] usbcore: registered new device driver usb [ 1.319134] media: Linux media interface: v0.10 [ 1.319161] videodev: Linux video capture interface: v2.00 [ 1.319279] pps_core: LinuxPPS API ver. 1 registered [ 1.319284] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giome tti <giometti@linux.it> [ 1.319298] PTP clock support registered [ 1.320938] clocksource: Switched to clocksource arch_sys_counter [ 1.424055] VFS: Disk quotas dquot_6.6.0 [ 1.424132] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.431689] NET: Registered protocol family 2 [ 1.432336] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) [ 1.432363] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 1.432445] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 1.432557] TCP: Hash tables configured (established 8192 bind 8192) [ 1.432659] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 1.432715] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 1.432989] NET: Registered protocol family 1 [ 1.433457] RPC: Registered named UNIX socket transport module. [ 1.433463] RPC: Registered udp transport module. [ 1.433465] RPC: Registered tcp transport module. [ 1.433469] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.433716] Trying to unpack rootfs image as initramfs... [ 1.732781] Freeing initrd memory: 4816K [ 1.734578] Initialise system trusted keyrings [ 1.734797] workingset: timestamp_bits=14 max_order=18 bucket_order=4 [ 1.740394] zbud: loaded [ 1.742539] NFS: Registering the id_resolver key type [ 1.742574] Key type id_resolver registered [ 1.742577] Key type id_legacy registered [ 1.742589] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.742594] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 1.743682] JFS: nTxBlock = 7984, nTxLock = 63876 [ 1.752402] SGI XFS with ACLs, security attributes, realtime, no debug enable d [ 1.760048] Key type asymmetric registered [ 1.760058] Asymmetric key parser 'x509' registered [ 1.760114] bounce: pool size: 64 pages [ 1.760192] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 46) [ 1.760333] io scheduler noop registered [ 1.760337] io scheduler deadline registered [ 1.760538] io scheduler cfq registered (default) [ 1.760544] io scheduler mq-deadline registered [ 1.760548] io scheduler kyber registered [ 1.760679] io scheduler bfq registered [ 1.761808] sun4i-usb-phy 1c19400.phy: Couldn't request ID GPIO [ 1.765742] sun8i-h3-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver [ 1.767257] sun8i-h3-r-pinctrl 1f02c00.pinctrl: initialized sunXi PIO driver [ 1.815385] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled [ 1.817624] console [ttyS0] disabled [ 1.837770] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 42, base_baud = 15 00000) is a U6_16550A [ 1.837822] console [ttyS0] enabled [ 1.861145] sun4i-drm display-engine: bound 1100000.mixer (ops 0xc0a85d08) [ 1.861405] sun4i-drm display-engine: bound 1c0c000.lcd-controller (ops 0xc0a 83454) [ 1.861459] sun8i-dw-hdmi 1ee0000.hdmi: 1ee0000.hdmi supply hvcc not found, u sing dummy regulator [ 1.861515] sun8i-dw-hdmi 1ee0000.hdmi: Linked as a consumer to regulator.0 [ 1.862297] sun8i-dw-hdmi 1ee0000.hdmi: Detected HDMI TX controller v1.32a wi th HDCP (sun8i_dw_hdmi_phy) [ 1.862638] sun8i-dw-hdmi 1ee0000.hdmi: registered DesignWare HDMI I2C bus dr iver [ 1.862868] sun4i-drm display-engine: bound 1ee0000.hdmi (ops 0xc0a8578c) [ 1.862874] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 1.862878] [drm] No driver support for vblank timestamp query. [ 1.862926] [drm] Cannot find any crtc or sizes [ 1.863371] [drm] Initialized sun4i-drm 1.0.0 20150629 for display-engine on minor 0 [ 1.866344] brd: module loaded [ 1.871673] loop: module loaded [ 1.873971] libphy: Fixed MDIO Bus: probed [ 1.874509] dwmac-sun8i 1c30000.ethernet: PTP uses main clock [ 1.874547] dwmac-sun8i 1c30000.ethernet: No regulator found [ 1.874867] dwmac-sun8i 1c30000.ethernet: Current syscon value is not the def ault 148000 (expect 58000) [ 1.874885] dwmac-sun8i 1c30000.ethernet: No HW DMA feature register supporte d [ 1.874890] dwmac-sun8i 1c30000.ethernet: RX Checksum Offload Engine supporte d [ 1.874896] dwmac-sun8i 1c30000.ethernet: COE Type 2 [ 1.874901] dwmac-sun8i 1c30000.ethernet: TX Checksum insertion supported [ 1.874907] dwmac-sun8i 1c30000.ethernet: Normal descriptors [ 1.874912] dwmac-sun8i 1c30000.ethernet: Chain mode enabled [ 1.875033] libphy: stmmac: probed [ 1.875456] dwmac-sun8i 1c30000.ethernet: Found internal PHY node [ 1.875542] libphy: mdio_mux: probed [ 1.875560] dwmac-sun8i 1c30000.ethernet: Switch mux to internal PHY [ 1.875567] dwmac-sun8i 1c30000.ethernet: Powering internal PHY [ 1.880365] libphy: mdio_mux: probed [ 1.881311] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.881316] ehci-platform: EHCI generic platform driver [ 1.881496] ehci-platform 1c1a000.usb: EHCI Host Controller [ 1.881522] ehci-platform 1c1a000.usb: new USB bus registered, assigned bus n umber 1 [ 1.882264] ehci-platform 1c1a000.usb: irq 26, io mem 0x01c1a000 [ 1.896950] ehci-platform 1c1a000.usb: USB 2.0 started, EHCI 1.00 [ 1.897199] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bc dDevice= 4.19 [ 1.897206] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 1.897212] usb usb1: Product: EHCI Host Controller [ 1.897218] usb usb1: Manufacturer: Linux 4.19.38-sunxi ehci_hcd [ 1.897223] usb usb1: SerialNumber: 1c1a000.usb [ 1.897782] hub 1-0:1.0: USB hub found [ 1.897827] hub 1-0:1.0: 1 port detected [ 1.898631] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.898656] ohci-platform: OHCI generic platform driver [ 1.898806] ohci-platform 1c1a400.usb: Generic Platform OHCI controller [ 1.898826] ohci-platform 1c1a400.usb: new USB bus registered, assigned bus n umber 2 [ 1.898997] ohci-platform 1c1a400.usb: irq 27, io mem 0x01c1a400 [ 1.961179] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bc dDevice= 4.19 [ 1.961187] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 1.961192] usb usb2: Product: Generic Platform OHCI controller [ 1.961198] usb usb2: Manufacturer: Linux 4.19.38-sunxi ohci_hcd [ 1.961203] usb usb2: SerialNumber: 1c1a400.usb [ 1.961642] hub 2-0:1.0: USB hub found [ 1.961686] hub 2-0:1.0: 1 port detected [ 1.962822] usbcore: registered new interface driver usb-storage [ 1.963545] sun6i-rtc 1f00000.rtc: rtc core: registered rtc-sun6i as rtc0 [ 1.963552] sun6i-rtc 1f00000.rtc: RTC enabled [ 1.963753] i2c /dev entries driver [ 1.965716] sunxi-wdt 1c20ca0.watchdog: Watchdog enabled (timeout=16 sec, now ayout=0) [ 1.966479] sunxi-mmc 1c0f000.mmc: Linked as a consumer to regulator.2 [ 1.966987] sunxi-mmc 1c0f000.mmc: Got CD GPIO [ 1.967255] ledtrig-cpu: registered to indicate activity on CPUs [ 1.967330] hidraw: raw HID events driver (C) Jiri Kosina [ 1.967462] usbcore: registered new interface driver usbhid [ 1.967465] usbhid: USB HID core driver [ 1.973600] Initializing XFRM netlink socket [ 1.974246] NET: Registered protocol family 10 [ 1.989082] Segment Routing with IPv6 [ 1.989184] NET: Registered protocol family 17 [ 1.989211] NET: Registered protocol family 15 [ 1.989269] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 1.989322] 8021q: 802.1Q VLAN Support v1.8 [ 1.989598] Key type dns_resolver registered [ 1.990033] Registering SWP/SWPB emulation handler [ 1.990580] registered taskstats version 1 [ 1.990586] Loading compiled-in X.509 certificates [ 1.990672] zswap: loaded using pool lzo/zbud [ 1.992335] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB [ 1.992482] Btrfs loaded, crc32c=crc32c-generic [ 1.999542] Key type encrypted registered [ 2.008278] sun4i-usb-phy 1c19400.phy: Linked as a consumer to regulator.4 [ 2.009274] ehci-platform 1c1b000.usb: EHCI Host Controller [ 2.009300] ehci-platform 1c1b000.usb: new USB bus registered, assigned bus n umber 3 [ 2.009829] ehci-platform 1c1b000.usb: irq 28, io mem 0x01c1b000 [ 2.024953] ehci-platform 1c1b000.usb: USB 2.0 started, EHCI 1.00 [ 2.025196] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bc dDevice= 4.19 [ 2.025203] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 2.025209] usb usb3: Product: EHCI Host Controller [ 2.025214] usb usb3: Manufacturer: Linux 4.19.38-sunxi ehci_hcd [ 2.025220] usb usb3: SerialNumber: 1c1b000.usb [ 2.025767] hub 3-0:1.0: USB hub found [ 2.025812] hub 3-0:1.0: 1 port detected [ 2.026580] ehci-platform 1c1c000.usb: EHCI Host Controller [ 2.026601] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus n umber 4 [ 2.026819] ehci-platform 1c1c000.usb: irq 30, io mem 0x01c1c000 [ 2.028948] mmc0: host does not support reading read-only switch, assuming wr ite-enable [ 2.031682] mmc0: new high speed SDHC card at address aaaa [ 2.032865] mmcblk0: mmc0:aaaa SL16G 14.8 GiB [ 2.035434] mmcblk0: p1 [ 2.040962] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 2.041170] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bc dDevice= 4.19 [ 2.041178] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 2.041183] usb usb4: Product: EHCI Host Controller [ 2.041189] usb usb4: Manufacturer: Linux 4.19.38-sunxi ehci_hcd [ 2.041194] usb usb4: SerialNumber: 1c1c000.usb [ 2.041688] hub 4-0:1.0: USB hub found [ 2.041728] hub 4-0:1.0: 1 port detected [ 2.042546] ehci-platform 1c1d000.usb: EHCI Host Controller [ 2.042581] ehci-platform 1c1d000.usb: new USB bus registered, assigned bus n umber 5 [ 2.042925] ehci-platform 1c1d000.usb: irq 32, io mem 0x01c1d000 [ 2.056952] ehci-platform 1c1d000.usb: USB 2.0 started, EHCI 1.00 [ 2.057137] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bc dDevice= 4.19 [ 2.057145] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 2.057150] usb usb5: Product: EHCI Host Controller [ 2.057155] usb usb5: Manufacturer: Linux 4.19.38-sunxi ehci_hcd [ 2.057161] usb usb5: SerialNumber: 1c1d000.usb [ 2.057607] hub 5-0:1.0: USB hub found [ 2.057641] hub 5-0:1.0: 1 port detected [ 2.058346] ohci-platform 1c1b400.usb: Generic Platform OHCI controller [ 2.058367] ohci-platform 1c1b400.usb: new USB bus registered, assigned bus n umber 6 [ 2.058559] ohci-platform 1c1b400.usb: irq 29, io mem 0x01c1b400 [ 2.121131] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001, bc dDevice= 4.19 [ 2.121139] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 2.121145] usb usb6: Product: Generic Platform OHCI controller [ 2.121150] usb usb6: Manufacturer: Linux 4.19.38-sunxi ohci_hcd [ 2.121156] usb usb6: SerialNumber: 1c1b400.usb [ 2.121600] hub 6-0:1.0: USB hub found [ 2.121636] hub 6-0:1.0: 1 port detected [ 2.122320] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 2.122341] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus n umber 7 [ 2.122507] ohci-platform 1c1c400.usb: irq 31, io mem 0x01c1c400 [ 2.185112] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001, bc dDevice= 4.19 [ 2.185120] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 2.185126] usb usb7: Product: Generic Platform OHCI controller [ 2.185131] usb usb7: Manufacturer: Linux 4.19.38-sunxi ohci_hcd [ 2.185136] usb usb7: SerialNumber: 1c1c400.usb [ 2.185572] hub 7-0:1.0: USB hub found [ 2.185606] hub 7-0:1.0: 1 port detected [ 2.186267] ohci-platform 1c1d400.usb: Generic Platform OHCI controller [ 2.186287] ohci-platform 1c1d400.usb: new USB bus registered, assigned bus n umber 8 [ 2.186453] ohci-platform 1c1d400.usb: irq 33, io mem 0x01c1d400 [ 2.249116] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001, bc dDevice= 4.19 [ 2.249123] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 2.249128] usb usb8: Product: Generic Platform OHCI controller [ 2.249134] usb usb8: Manufacturer: Linux 4.19.38-sunxi ohci_hcd [ 2.249139] usb usb8: SerialNumber: 1c1d400.usb [ 2.249569] hub 8-0:1.0: USB hub found [ 2.249605] hub 8-0:1.0: 1 port detected [ 2.250323] usb_phy_generic usb_phy_generic.2.auto: usb_phy_generic.2.auto su pply vcc not found, using dummy regulator [ 2.250380] usb_phy_generic usb_phy_generic.2.auto: Linked as a consumer to r egulator.0 [ 2.250661] musb-hdrc musb-hdrc.3.auto: MUSB HDRC host driver [ 2.250671] musb-hdrc musb-hdrc.3.auto: new USB bus registered, assigned bus number 9 [ 2.250898] usb usb9: New USB device found, idVendor=1d6b, idProduct=0002, bc dDevice= 4.19 [ 2.250906] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 2.250912] usb usb9: Product: MUSB HDRC host driver [ 2.250917] usb usb9: Manufacturer: Linux 4.19.38-sunxi musb-hcd [ 2.250922] usb usb9: SerialNumber: musb-hdrc.3.auto [ 2.251328] hub 9-0:1.0: USB hub found [ 2.251367] hub 9-0:1.0: 1 port detected [ 2.252322] sun6i-rtc 1f00000.rtc: setting system clock to 2019-06-08 14:39:0 2 UTC (1560004742) [ 2.252511] of_cfs_init [ 2.252617] of_cfs_init: OK [ 2.252766] vcc3v0: disabling [ 2.252772] vcc5v0: disabling [ 2.252775] usb0-vbus: disabling [ 2.256085] Freeing unused kernel memory: 1024K [ 2.265130] Run /init as init process [ 2.310969] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 2.311502] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 2.311614] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 2.877052] [drm] Cannot find any crtc or sizes [ 3.354045] random: fast init done [ 3.380729] EXT4-fs (mmcblk0p1): mounted filesystem with writeback data mode. Opts: (null) [ 3.900171] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SEL INUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL + XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN) [ 3.900649] systemd[1]: Detected architecture arm. [ 3.905044] systemd[1]: Set hostname to <orangepipc>. [ 4.273369] systemd[1]: Reached target Remote File Systems. [ 4.274239] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ 4.274531] systemd[1]: Reached target Swap. [ 4.275049] systemd[1]: Listening on Journal Socket. [ 4.276111] systemd[1]: Created slice User and Session Slice. [ 4.276556] systemd[1]: Listening on udev Kernel Socket. [ 4.277611] systemd[1]: Set up automount Arbitrary Executable File Formats Fi le System Automount Point. [ 4.433678] EXT4-fs (mmcblk0p1): re-mounted. Opts: commit=600,errors=remount- ro [ 4.691087] systemd-journald[222]: Received request to flush runtime journal from PID 1 [ 5.132024] cpu cpu0: Linked as a consumer to regulator.5 [ 5.132251] cpu cpu0: Dropping the link to regulator.5 [ 5.132450] cpu cpu0: Linked as a consumer to regulator.5 [ 5.133762] input: r_gpio_keys as /devices/platform/r_gpio_keys/input/input0 [ 5.293732] sun8i_ths 1c25000.thermal-sensor: no memory resources defined [ 5.293761] sun8i_ths: probe of 1c25000.thermal-sensor failed with error -22 [ 5.375574] thermal thermal_zone0: failed to read out thermal zone (-110) [ 5.387173] Registered IR keymap rc-empty [ 5.387280] rc rc0: sunxi-ir as /devices/platform/soc/1f02000.ir/rc/rc0 [ 5.387408] input: sunxi-ir as /devices/platform/soc/1f02000.ir/rc/rc0/input1 [ 5.387628] rc rc0: lirc_dev: driver sunxi-ir registered at minor = 0, raw IR receiver, no transmitter [ 5.388395] sunxi-ir 1f02000.ir: initialized sunXi IR driver [ 5.421316] sun4i-codec 1c22c00.codec: ASoC: codec-analog@1f015c0 not registe red [ 5.421334] sun4i-codec 1c22c00.codec: Failed to register our card [ 5.424772] sun4i-codec 1c22c00.codec: ASoC: codec-analog@1f015c0 not registe red [ 5.424787] sun4i-codec 1c22c00.codec: Failed to register our card [ 5.436013] lima 1c40000.gpu: bus rate = 200000000 [ 5.436028] lima 1c40000.gpu: mod rate = 384000000 [ 5.436204] sun4i-codec 1c22c00.codec: ASoC: Failed to create component debug fs directory [ 5.437269] [TTM] Zone kernel: Available graphics memory: 380458 kiB [ 5.437279] [TTM] Zone highmem: Available graphics memory: 511524 kiB [ 5.437283] [TTM] Initializing pool allocator [ 5.438034] lima 1c40000.gpu: gp - mali400 version major 1 minor 1 [ 5.438081] lima 1c40000.gpu: pp0 - mali400 version major 1 minor 1 [ 5.438133] lima 1c40000.gpu: pp1 - mali400 version major 1 minor 1 [ 5.438169] lima 1c40000.gpu: l2 cache 64K, 4-way, 64byte cache line, 64bit e xternal bus [ 5.442986] sun4i-codec 1c22c00.codec: Codec <-> 1c22c00.codec mapping ok [ 5.462103] [drm] Initialized lima 1.0.0 20170325 for 1c40000.gpu on minor 1 [ 5.505632] zram: Added device: zram0 [ 5.508452] zram: Added device: zram1 [ 5.509943] zram: Added device: zram2 [ 5.611967] zram1: detected capacity change from 0 to 523800576 [ 5.680849] Adding 511520k swap on /dev/zram1. Priority:5 extents:1 across:5 11520k SSFS [ 5.793771] zram0: detected capacity change from 0 to 52428800 [ 6.078183] Generic PHY 0.1:01: attached PHY driver [Generic PHY] (mii_bus:ph y_addr=0.1:01, irq=POLL) [ 6.079709] dwmac-sun8i 1c30000.ethernet eth0: No Safety Features support fou nd [ 6.079722] dwmac-sun8i 1c30000.ethernet eth0: No MAC Management Counters ava ilable [ 6.079729] dwmac-sun8i 1c30000.ethernet eth0: PTP not supported by HW [ 6.080064] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 6.498250] EXT4-fs (zram0): mounted filesystem without journal. Opts: discar d [ 6.531648] random: crng init done [ 6.531661] random: 7 urandom warning(s) missed due to ratelimiting [ 9.149507] dwmac-sun8i 1c30000.ethernet eth0: Link is Up - 100Mbps/Full - fl ow control rx/tx [ 9.149547] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready pi@orangepipc:~$ is my board damaged? Link to comment Share on other sites More sharing options...
Igor Posted June 8, 2019 Share Posted June 8, 2019 4 minutes ago, cam2019 said: after changing to 3amps 5v psu still i get this How do you power your board? What kind of cable do you use? Can you make a photo? Link to comment Share on other sites More sharing options...
cam2019 Posted June 8, 2019 Author Share Posted June 8, 2019 http://ix.io/1Lfc its just an improvised one. barrel jack to opi pc and a 5v from our own rpi3b+ custom board. the reason why i sorted to using the output of our custom board because i ran out of options. used 2 buck converters and still no luck. i am sure its at least 3 amps 5v as was designed by our engineer. Link to comment Share on other sites More sharing options...
cam2019 Posted June 8, 2019 Author Share Posted June 8, 2019 Link to comment Share on other sites More sharing options...
Igor Posted June 8, 2019 Share Posted June 8, 2019 Measure 5V line on USB port to see if its within tolerance. Running low on ideas ... ofc it can be some hardware defects - in that case we both waste time. 1 Link to comment Share on other sites More sharing options...
cam2019 Posted June 8, 2019 Author Share Posted June 8, 2019 thanks for the support appreciate much Link to comment Share on other sites More sharing options...
cam2019 Posted June 8, 2019 Author Share Posted June 8, 2019 i already used 2nd board. i have 3. still no eth1. maybe its with the latest build of armbian? Link to comment Share on other sites More sharing options...
Igor Posted June 8, 2019 Share Posted June 8, 2019 13 minutes ago, cam2019 said: maybe its with the latest build of armbian? Or quirky driver/hardware combo which we didn't make and will not even try to fix. 1 Link to comment Share on other sites More sharing options...
cam2019 Posted June 8, 2019 Author Share Posted June 8, 2019 understood. thanks again Link to comment Share on other sites More sharing options...
guidol Posted June 8, 2019 Share Posted June 8, 2019 1 hour ago, cam2019 said: i already used 2nd board. i have 3. still no eth1. maybe its with the latest build of armbian? when you did try different boards - did you also try all of the !three! usb-ports on every board? specially the single one on the other side of the eth0-port? Because in you first dmesg the USB-Ethernet adapter was recognized as eth1 and then renamed. And this renamed name wouldnt go in every situation automatically up for ifconfig. So check the other usb-ports and when you will see enx00e04c680046 in dmesg get him up with ifconfig enx00e04c680046 up and then he would be displayed in ifconfig when the port is down (not automatically up or no cable/link connected the interface is in down state) then it wouldnt displayed by ifconfig The part after enx is the MAC-address of your USB3.0 Ethernet-adapter. I got this model running on my devices without special power supply and from my personal view there is no driver problem with armbian and this device. 1 Link to comment Share on other sites More sharing options...
cam2019 Posted June 8, 2019 Author Share Posted June 8, 2019 i got it working now. what did i do? i plugged in 3 gigabits all at the same time then it all got registered in ifconfig. and removed 1 by 1 until i only have 1. [sudo] password for pi: enx00e04c68012f: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 10.10.10.1 netmask 255.255.254.0 broadcast 10.10.11.255 inet6 fe80::5712:3fed:cdaa:9ee3 prefixlen 64 scopeid 0x20<link> ether 00:e0:4c:68:01:2f txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 44 bytes 5108 (4.9 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.2.110 netmask 255.255.255.0 broadcast 192.168.2.255 inet6 fe80::ecc5:4572:5bee:8fcd prefixlen 64 scopeid 0x20<link> ether 02:81:0c:80:12:7d txqueuelen 1000 (Ethernet) RX packets 749 bytes 52425 (51.1 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 132 bytes 17546 (17.1 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 38 lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 inet6 ::1 prefixlen 128 scopeid 0x10<host> loop txqueuelen 1000 (Local Loopback) RX packets 14 bytes 630 (630.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 14 bytes 630 (630.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 pi@orangepipc:~$ Link to comment Share on other sites More sharing options...
cam2019 Posted June 8, 2019 Author Share Posted June 8, 2019 eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.2.110 netmask 255.255.255.0 broadcast 192.168.2.255 inet6 fe80::ecc5:4572:5bee:8fcd prefixlen 64 scopeid 0x20<link> ether 02:81:0c:80:12:7d txqueuelen 1000 (Ethernet) RX packets 548 bytes 49314 (48.1 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 159 bytes 21987 (21.4 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 38 eth1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 10.10.10.1 netmask 255.255.254.0 broadcast 10.10.11.255 inet6 fe80::6ffa:2eb7:3e4d:50f prefixlen 64 scopeid 0x20<link> ether 00:e0:4c:68:01:2f txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 72 bytes 9425 (9.2 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 inet6 ::1 prefixlen 128 scopeid 0x10<host> loop txqueuelen 1000 (Local Loopback) RX packets 10 bytes 474 (474.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 10 bytes 474 (474.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 pi@orangepipc:~$ it is now eth1 using this Thanks @guidol and @Igor will bother you again soon Link to comment Share on other sites More sharing options...
guidol Posted June 8, 2019 Share Posted June 8, 2019 14 minutes ago, cam2019 said: it is now eth1 Thanks @guidol and @Igor will bother you again soon we will see how long it does work after a reboot 1 Link to comment Share on other sites More sharing options...
cam2019 Posted June 8, 2019 Author Share Posted June 8, 2019 Link to comment Share on other sites More sharing options...
Recommended Posts