All Armbians with Kernel 6.8.x woun't start on Radaxa Rock 5b

[Tomogo]

Hi,

I have tried Rock 5b images with Kernel 6.8.10. Any of image I've tested will not start.

No LED flashing, no HDMI signal.. nothing.

The others with Kernel 6.1.43 starts fine. 

[Werner]

https://debug.armbian.de

[Tomogo]

Hi,

I hate you (sorry just joke) 🙂

 

I have no UART to USB cable so I found old Teensy 3.2 board. Made program for Serial to USB bridge.

Updated SPI flash with new firmware with debug mode.

And....

 

It works now! Dam or huray... 😉

 

LPDDR4X, 2112MHz

channel[0] BW=16 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=8 Size=4096MB

channel[1] BW=16 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=8 Size=4096MB

channel[2] BW=16 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=8 Size=4096MB

channel[3] BW=16 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=8 Size=4096MB

Manufacturer ID:0x6

CH0 RX Vref:27.5%, TX Vref:25.8%,25.8%

CH1 RX Vref:25.8%, TX Vref:25.8%,25.8%

CH2 RX Vref:27.9%, TX Vref:24.8%,24.8%

CH3 RX Vref:27.1%, TX Vref:24.8%,24.8%

change to F1: 528MHz

change to F2: 1068MHz

change to F3: 1560MHz

change to F0: 2112MHz

out

U-Boot SPL board init

U-Boot SPL 2017.09-gd1cf49135ee-220414-dirty #stephen (May 23 2024 - 19:39:28)

Trying to boot from MMC2

MMC: no card present

mmc_init: -123, time 0

spl: mmc init failed with error: -123

Trying to boot from MTD2

Trying fit image at 0x4000 sector

## Verified-boot: 0

## Checking atf-1 0x00040000 ... sha256(a7d1d8d191...) + OK

## Checking uboot 0x00200000 ... sha256(25a398ffe0...) + OK

## Checking fdt 0x0031e9f8 ... sha256(5bee414074...) + OK

## Checking atf-2 0xff100000 ... sha256(4b2065349b...) + OK

## Checking atf-3 0x000f0000 ... sha256(aa71013e72...) + OK

Jumping to U-Boot(0x00200000) via ARM Trusted Firmware(0x00040000)

Total: 489.724/719.766 ms

 

INFO: Preloader serial: 2

NOTICE: BL31: v2.3():v2.3-682-g4ca8a8422:derrick.huang, fwver: v1.45

NOTICE: BL31: Built : 10:11:21, Dec 27 2023

INFO: spec: 0x1

INFO: code: 0x88

INFO: ext 32k is not valid

INFO: ddr: stride-en 4CH

INFO: GICv3 without legacy support detected.

INFO: ARM GICv3 driver initialized in EL3

INFO: valid_cpu_msk=0xff bcore0_rst = 0x0, bcore1_rst = 0x0

INFO: l3 cache partition cfg-0

INFO: system boots from cpu-hwid-0

INFO: disable memory repair

INFO: idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001

INFO: dfs DDR fsp_params[0].freq_mhz= 2112MHz

INFO: dfs DDR fsp_params[1].freq_mhz= 528MHz

INFO: dfs DDR fsp_params[2].freq_mhz= 1068MHz

INFO: dfs DDR fsp_params[3].freq_mhz= 1560MHz

INFO: BL31: Initialising Exception Handling Framework

INFO: BL31: Initializing runtime services

WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK

ERROR: Error initializing runtime service opteed_fast

INFO: BL31: Preparing for EL3 exit to normal world

INFO: Entry point address = 0x200000

INFO: SPSR = 0x3c9

 

 

U-Boot 2017.09-gd1cf49135ee-220414-dirty #stephen (May 23 2024 - 19:39:28 +0800)

 

Model: Radxa ROCK 5B

MPIDR: 0x81000000

PreSerial: 2, raw, 0xfeb50000

DRAM: 16 GiB

Sysmem: init

Relocation Offset: eda3f000

Relocation fdt: eb9f96c0 - eb9fecc8

CR: M/C/I

Using default environment

 

DM: v2

mmc@fe2c0000: 1, mmc@fe2e0000: 0

Bootdev(assign): mmc 0

MMC0: HS400 Enhanced Strobe, 200Mhz

PartType: EFI

No misc partition

boot mode: None

FIT: No boot partition

Failed to load DTB, ret=-2

No valid DTB, ret=-22

Failed to get kernel dtb, ret=-22

Model: Radxa ROCK 5B

MPIDR: 0x81000000

CLK: (sync kernel. arm: enter 1008000 KHz, init 1008000 KHz, kernel 0N/A)

b0pll 24000 KHz

b1pll 24000 KHz

lpll 24000 KHz

v0pll 24000 KHz

aupll 24000 KHz

cpll 1500000 KHz

gpll 1188000 KHz

npll 24000 KHz

ppll 1100000 KHz

aclk_center_root 702000 KHz

pclk_center_root 100000 KHz

hclk_center_root 396000 KHz

aclk_center_low_root 500000 KHz

aclk_top_root 750000 KHz

pclk_top_root 100000 KHz

aclk_low_top_root 396000 KHz

Net: No ethernet found.

Hit key to stop autoboot('CTRL+C'): 0

starting USB...

No working controllers found

USB is stopped. Please issue 'usb start' first.

MMC: no card present

mmc_init: -123, time 0

pcie@fe150000: PCIe Linking... LTSSM is 0x0

pcie@fe150000: PCIe Linking... LTSSM is 0x0

pcie@fe150000: PCIe Linking... LTSSM is 0x6

pcie@fe150000: PCIe Linking... LTSSM is 0x210023

pcie@fe150000: PCIe Link up, LTSSM is 0x230011

pcie@fe150000: PCIE-0: Link up (Gen3-x2, Bus0)

pcie@fe150000: invalid flags type!

 

Device 0: unknown device

 

Device 1: unknown device

switch to partitions #0, OK

mmc0(part 0) is current device

Scanning mmc 0:1...

Found U-Boot script /boot/boot.scr

3920 bytes read in 8 ms (478.5 KiB/s)

## Executing script at 00500000

Boot script loaded from mmc 0:1

172 bytes read in 8 ms (20.5 KiB/s)

26373283 bytes read in 112 ms (224.6 MiB/s)

32436736 bytes read in 142 ms (217.8 MiB/s)

163397 bytes read in 28 ms (5.6 MiB/s)

Trying kaslrseed command... Info: Unknown command can be safely ignored since kaslrseed does not apply to all boards.

Unknown command 'kaslrseed' - try 'help'

Fdt Ramdisk skip relocation

No misc partition

## Loading init Ramdisk from Legacy Image at 0a200000 ...

Image Name: uInitrd

Image Type: AArch64 Linux RAMDisk Image (gzip compressed)

Data Size: 26373219 Bytes = 25.2 MiB

Load Address: 00000000

Entry Point: 00000000

Verifying Checksum ... OK

## Flattened Device Tree blob at 0x08300000

Booting using the fdt blob at 0x08300000

reserving fdt memory region: addr=8300000 size=8e000

Using Device Tree in place at 0000000008300000, end 0000000008390fff

can't found rockchip,drm-logo, use rockchip,fb-logo

WARNING: could not set reg FDT_ERR_BADOFFSET.

failed to reserve fb-loader-logo memory

WARNING: could not set reg FDT_ERR_BADOFFSET.

Adding bank: 0x00200000 - 0xf0000000 (size: 0xefe00000)

Adding bank: 0x100000000 - 0x3fc000000 (size: 0x2fc000000)

Adding bank: 0x3fc500000 - 0x3fff00000 (size: 0x03a00000)

Adding bank: 0x4f0000000 - 0x500000000 (size: 0x10000000)

Total: 2321.467/3095.859 ms

 

Starting kernel ...

 

 

[Igor]

9 hours ago, Tomogo said:

The others with Kernel 6.1.43 starts fine. 

Kernel 6.8.y is hit and miss. We need to separate download links somehow ... for now it was added "Kernel 6.8.y is at experimental support level! Not all features work but it runs fairy stable." to warn you. Its good to be there, as they are usable - where they work. I run several github runners on Rock5 without any troubles for months.