MacBreaker

@orangepie14 There a differed ways to connect. You have skills with soldering or not? Ok,easyst way is to buy a usb to DC 4mm connector cable and a power source form Raspberry Pi. It doesn't matter if mirousb or usb-c connector. Plug all together and your done. Bevor i forget, i use 3000 miliampere Cells. Made sukcessfull tests with 1 hour disconnect from mains and reconnect. All wthout problems... Markus

@orangepie14 ..about power outages.. I had this problem years argo also. I run a server (Orange Pi PC) 24/7 in a area with a lot of "power outages". I prevent this with a board like this: Double 18650 Lithium-Batterie Schild V8 Mobile Power bank You have only to connect it between your power source and you Pi. That's all.. Markus

Type this in a terminal: sudo apt install v4l-utils after installing this, you can try your connand again..

Hi @jtmpush18, you can set a new password for omv with: sudo omv-firstaid some reading will help you...

...

@RockBian did you try sudo htop?

@jslav about video* take a look here: check the active modules and blacklist them...

@buratino did you try this? Maybe it helps...

Hi, i know the problem , but when you type "lsmod" you can see all aktive modules and the writing.. About the other problem. Maybe you can set a filter in your script that allow only "even numbers" and skip "odd numbers".. ..just my thougts about this. greetings Markus

Hello @Godfabber, i think i understand your problem. First let's check lsusb master@Zero-Bk:~$ lsusb Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 002: ID 045e:0779 Microsoft Corp. LifeCam HD-3000 Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 7392:7811 Edimax Technology Co., Ltd EW-7811Un 802.11n Wireless Adapter [Realtek RTL8188CUS] Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub ..as you can see, a usbcam is detected: Microsoft Corp. LifeCam HD-3000 What gives you a ls -ltrh /dev/video* master@Zero-Bk:~$ ls -ltrh /dev/video* crw-rw---- 1 root video 81, 0 Sep 6 12:20 /dev/video0 crw-rw---- 1 root video 81, 1 Sep 6 12:20 /dev/video1 crw-rw---- 1 root video 81, 3 Sep 6 12:20 /dev/video3 crw-rw---- 1 root video 81, 2 Sep 6 12:20 /dev/video2 or sudo apt-get install v4l-utils v4l2-ctl --list-devices In my case: master@Zero-Bk:~$ v4l2-ctl --list-devices cedrus (platform:cedrus): /dev/video0 sun8i-di (platform:sun8i-di): /dev/video1 Microsoft® LifeCam HD-3000: Mi (usb-1c1c000.usb-1): /dev/video2 /dev/video3 That means that the module sunxi_cedrus and sun8i_di has to be blacklisted... sudo nano /etc/modprobe.d/sunxi_cedrus.conf blacklist sunxi_cedrus and: sun8i_di sudo nano /etc/modprobe.d/sun8i_di.conf blacklist sun8i_di sudo reboot After reboot you see this after typing v4l2-ctl --list-devices: Microsoft® LifeCam HD-3000: Mi (usb-1c1c000.usb-1): /dev/video0 /dev/video1 so, you have now only your webcam as video-device.. ..hope it helps...

Only to keep it clear.. XU4,HC1 and HC2 is 32Bit.

To enable I2S is easy. See this thread: Have you tried the search function up on the right side? You can do it on your Orange Pi PC Plus the same way Guido did it on Nanopi Neo.

so... on the first try, i was doing everything right. Didn't realize that SimpNAS is BETA and found my problem here LINK . Exept this, it work well...

Hi Tido, thanks for clarification of root or root privileges. i didn't know this, sorry. I will read the README.md and start over again on the weekend. Ich hoffe...

Hi Tido, did you read and understood my post? What you like to point me? Yes, i ran the install script as root..