Jump to content

Armbian for Amlogic S912


chocho

Recommended Posts

On 17.02.2018 at 1:28 AM, alanoliver said:

 

My friend, did you run the 4.9.x kernel on Beelink GT1? I'm trying to run more than not boot.

Asked balbes150 same question, but about Beelink GT1 Ultimate. It's only possible to rub 3.xx kernel on this device.

Link to comment
Share on other sites

18 hours ago, ArtUrlWWW said:

Asked balbes150 same question, but about Beelink GT1 Ultimate. It's only possible to rub 3.xx kernel on this device.

A new u-boot is needed to run kernel 4.9. I checked on my Tronsmart Vega S96 (S912) - with the dtb from VIM2 and the new u-boot system working with the 4.9 core.

Link to comment
Share on other sites

Hardware: AlfaWise H96 Pro+

Armbian Version: Armbian_5.37_S9xxx_Ubuntu_xenial_4.9.40_server_20180204.img.xz

SOC: Amlogic S912

 

First thanks to all the people evolved in this great project :)

 

This is my first post here, I'm a newer armbian user :)

 

I'm using it has a headless server for my projects with docker and mongodb and my spring boot/aurelia framework projects,

and it works like a real server, without lags at all, simple awesome , my main objective is put my solutions in a economic/cheaper server :)

 

I already do that in raspberry pi 3, but I miss one important part that is use it has a Access Point with HostAPD like in RPI

 

Next the problem:

 

I Have problems configure Wifi card,

I cant use Wifi at all, and dont have wlan0


 

mario@amlogic:~$ dmesg | grep wlan0

mario@amlogic:~$ dmesg | grep wifi
[ 1.024140] wifi: power_on_pin_OD = 0;
[ 1.024254] aml_wifi wifi: [wifi_dev_probe] no power_on_pin2
[ 1.024460] aml_wifi wifi: [pwm_double_channel_conf_dt] wifi pwm dt ok
[ 1.024604] aml_wifi wifi: [pwm_double_channel_conf] wifi pwm conf ok
[ 1.024737] aml_wifi wifi: [wifi_dev_probe] interrupt_pin=97
[ 1.024855] aml_wifi wifi: [wifi_dev_probe] irq_num=0, irq_trigger_type=1
[ 1.024992] aml_wifi wifi: [wifi_dev_probe] power_on_pin=96
[ 1.025108] aml_wifi wifi: [wifi_dev_probe] clock_32k_pin=0
[ 1.025595] aml_wifi wifi: [wifi_setup_dt] wifi_setup_dt
[ 1.025757] aml_wifi wifi: [wifi_setup_dt] irq num is:(126)
[ 1.025874] aml_wifi wifi: [wifi_setup_dt] interrupt_pin(97)
[ 1.026007] aml_wifi wifi: [wifi_setup_dt] power_on_pin(96)
[ 4.195633] efusekeyname: mac_wifi  offset: 24 size: 12

I try everything that I remember, read a lot here in this post about wifi,

but I dont even know if my alfawise is working with wifi

 

I try all the DTBs from this armbian release one by one,

with modprobe, but nothing

 

  • gxl_p230_2g.dtb
  • gxl_p231_1g.dtb
  • gxl_p231_2g.dtb
  • gxl_p400_2g.dtb
  • gxl_p401_2g.dtb
  • gxm_p200_2g.dtb
  • kvim2_android.dtb
  • kvim2_linux.dtb
  • kvim2_multios.dtb
  • kvim2_volumio.dtb
  • kvim_android.dtb
  • kvim_linux.dtb
  •  

I try to follow this post https://forum.armbian.com/topic/2138-armbian-for-amlogic-s912/?page=19&tab=comments#comment-49228

 

added wifi_dummy to /etc/modules

 

I even get driver from android firmware SCV4-Test1-Blue-PCB-H96ProPlus.zip

(the link to cfg80211 driver from above post is broken)

 

copied to /lib/modules/4.9.40/kernel/drivers/net/wireless/

 

and try to use modprobe on it like explained in above post

 

sudo modprobe cfg80211
modprobe dhd
modprobe: ERROR: could not insert 'dhd': No such device

but It never works, It seems I need help......i'm a bit lost now, without any wise idea of how I can configure wifi in this device

 

Or maybe I'm doing something stupid, or don't even know how to do it (I bet on this horse LOL)

 

The other problem is I cant backup my /dev/mmcblk0

 

always have the error `error reading '/dev/mmcblk0': Input/output error`

 

try many times, even try to use hard-disk and samba share but the problem is reading the mmcblk0

it always fail!

 

I try to backup, because I like to install armbian on mmcblk0

I dont need android, maybe in a near future, or when I like to sell it


 

$ sudo ddbr
DO YOU WANT TO BACKUP OR RESTORE ?
BACKUP=(b) RESTORE=(r) b
AVAILABLE DEVICES: mmcblk0 sda1 sda2
YOU ARE RUNNING xenial FROM sda2
INTERNAL EMMC IS: mmcblk0 SIZE:  30535680
ROOT (sda2) FREE SPACE IS:   74266064
DO YOU WANT COMPRESSION ?
YES=(y) NO=(n) n
SAVING mmcblk0 TO /ddbr/Amlogic-emmc.img...
dd: error reading '/dev/mmcblk0': Input/output error

Thanks to all, for the excellent distro

Edited by koakh
Prettify Post
Link to comment
Share on other sites

25 minutes ago, balbes150 said:

I recommend using 5.41 (mali6)

Thanks @balage

 

Can we send me the link or the filename of 5.41 mali server?

 

Thanks

 

edited: I think I found it here (Armbian_5.41_S9xxx_Ubuntu_xenial_3.14.29_server_20180225.img.xz)

 

can You confirm that is the advised version

 

Thanks (Again)

Link to comment
Share on other sites

10 hours ago, balbes150 said:

yes

Thanks @balbes150

 

After Installed Armbian_5.41_S9xxx_Ubuntu_xenial_3.14.29_server_20180225

Now I have wlan0 but I cant use it :(

 

$ cat /etc/modules
#aml_nftl_dev
#wifi_dummy
cfg80211
dhd

$ lsmod
Module                  Size  Used by
wlan                 3435325  0
xt_addrtype             2923  2
zram                    8953  8
ch341                   5434  0
rtc_hym8563             5568  0
cfg80211              415017  1 wlan


 $ sudo lshw
  ...
  *-network:1
       description: Wireless interface
       physical id: 4
       logical name: wlan0
       serial: 84:5d:d7:4a:32:02
       capabilities: ethernet physical wireless
       configuration: broadcast=yes driver=ar6k_wlan driverversion=3.14.29 firmware=N/A link=no multicast=yes wireless=Qcom:802.11n

$ wlan0     Link encap:Ethernet  HWaddr 84:5d:d7:4a:32:02  
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

nmtui can't scan networks/activate networks

 

I try manually play with device with 

$ sudo iw dev
phy#0
    Interface p2p0
        ifindex 7
        wdev 0x2
        addr 86:5d:d7:cf:32:02
        type P2P-device
    Interface wlan0
        ifindex 6
        wdev 0x1
        addr 84:5d:d7:4a:32:02
        type managed


$ iw wlan0 link

$ sudo ip link set wlan0 up

$ sudo ip link show wlan0
6: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DORMANT group default qlen 1000
    link/ether 84:5d:d7:4a:32:02 brd ff:ff:ff:ff:ff:ff

$ sudo iw wlan0 link

$ sudo iw wlan0 scan
(wait a 40sec and output nothing, it cant find any network, like nmtui ) 

seems like im playing with a wifi_dummy

 

$ dmesg | grep wifi
[    2.342807] aml_wifi wifi.35: [wifi_dev_probe] no power_on_pin2
[    2.342823] aml_wifi wifi.35: [wifi_dev_probe] set pwm as 32k output
[    2.342882] aml_wifi wifi.35: [wifi_dev_probe] dhd_static_buf setup
[    2.342977] aml_wifi wifi.35: [wifi_dev_probe] interrupt_pin=241
[    2.342991] aml_wifi wifi.35: [wifi_dev_probe] irq_num=100, irq_trigger_type=1
[    2.343006] aml_wifi wifi.35: [wifi_dev_probe] power_on_pin=240
[    2.343019] aml_wifi wifi.35: [wifi_dev_probe] clock_32k_pin=0
[    2.343354] aml_wifi wifi.35: [wifi_setup_dt] wifi_setup_dt
[    2.343399] aml_wifi wifi.35: [wifi_setup_dt] interrupt_pin(241)
[    2.343421] aml_wifi wifi.35: [wifi_setup_dt] power_on_pin(240)
[    6.383600] efusekeyname:        mac_wifi    offset:    12    size:     6
[  207.567537] aml_wifi wifi.35: [extern_wifi_set_enable] WIFI  Disable! 240
[  207.870725] aml_wifi wifi.35: [extern_wifi_set_enable] WIFI  Enable! 240
[  208.458580] aml_wifi wifi.35: [extern_wifi_set_enable] WIFI  Disable! 240
[  208.658625] aml_wifi wifi.35: [extern_wifi_set_enable] WIFI  Enable! 240
[  210.348703] dhd_wifi_platform_load: Enter
[  210.348750] wifi_platform_set_power = 1
[  210.348800] aml_wifi wifi.35: [extern_wifi_set_enable] WIFI  Disable! 240
[  210.548955] aml_wifi wifi.35: [extern_wifi_set_enable] WIFI  Enable! 240
[  211.050686] wifi_platform_bus_enumerate device present 1
[  213.126880] wifi_platform_set_power = 0
[  213.126905] wifi_platform_bus_enumerate device present 0
[  213.126953] aml_wifi wifi.35: [extern_wifi_set_enable] WIFI  Disable! 240
[  213.327004] wifi_platform_set_power = 1
[  213.327035] aml_wifi wifi.35: [extern_wifi_set_enable] WIFI  Disable! 240
[  213.527065] aml_wifi wifi.35: [extern_wifi_set_enable] WIFI  Enable! 240
[  214.030677] wifi_platform_bus_enumerate device present 1
[  216.106908] wifi_platform_set_power = 0
[  216.106933] wifi_platform_bus_enumerate device present 0
[  216.106981] aml_wifi wifi.35: [extern_wifi_set_enable] WIFI  Disable! 240
[  216.307030] wifi_platform_set_power = 1
[  216.307064] aml_wifi wifi.35: [extern_wifi_set_enable] WIFI  Disable! 240
[  216.507115] aml_wifi wifi.35: [extern_wifi_set_enable] WIFI  Enable! 240

 

$ sudo modprobe cfg80211
$ sudo modprobe dhd
modprobe: ERROR: could not insert 'dhd': No such device

Maybe someone can help, I try hard, but it seems without some help I'm trapped here, cant use WiFi card :(

 

update: I dont have tried all the DTBs......only when I have a monitor and keyboard connected to box, currently my only have ssh

 

Thanks to all

 

Link to comment
Share on other sites

1 hour ago, balbes150 said:

modprobe qca9377

 

or

 

modprobe wlan

 

Thanks it work até first line with

 

modprobe Alan

 

Now I ser the networks in nmtui ;)

 

Thanks @balbes150 you spare me a few suffering hours. 

 

Its so easy when we have the knowledge, and so hard when we are try and fail to learn ;)

 

Once again you are the man

 

PS. Sorry my bad English. Its not my native language....

Link to comment
Share on other sites

5 hours ago, balbes150 said:

modprobe qca9377

 

or

 

modprobe wlan

 

Hello Again

 

I use "modprobe wlan" and it "load" module and I can use wifi :) (Thanks Again)

 

but, after reboot, I must always do the same "modprobe wlan"

 

I put wlan on /etc/modules but it wont "load" wlan on boot

It only works with above combination, and launch "modprobe wlan" after boot/login

cat /etc/modules
aml_nftl_dev
#wifi_dummy
cfg80211
dhd
# this is note loaded
wlan

Any idea is appreciated, thanks

 

Update:

$ dmesg | grep wlan

$ dmesg | grep wlan
[    2.352247] Wifi: bcmdhd_init_wlan_mem: bcmdhd_init_wlan_mem: WIFI MEM Allocated
[   13.191319] ======== dhd_wlan_init_plat_data ========
[   13.222553] dhd_wlan_init_gpio: GPIO(WL_REG_ON) = -1
[   13.253521] dhd_wlan_init_gpio: GPIO(WL_HOST_WAKE) = -1
[   13.263757] dhd_wlan_init_gpio: host_oob_irq: 100
[   13.271307] dhd_wlan_init_gpio: host_oob_irq_flags=0x414
[   15.594082] wlan: loading driver v4.5.20.037
[   27.130863] ======== dhd_wlan_deinit_plat_data ========
[   27.141717] ======== dhd_wlan_init_plat_data ========
[   27.146895] dhd_wlan_init_gpio: GPIO(WL_REG_ON) = -1
[   27.151961] dhd_wlan_init_gpio: GPIO(WL_HOST_WAKE) = -1
[   27.157505] dhd_wlan_init_gpio: host_oob_irq: 100
[   27.162239] dhd_wlan_init_gpio: host_oob_irq_flags=0x414
[   35.674650] wlan: driver load failure
[   40.973680] ======== dhd_wlan_deinit_plat_data ========
[   40.984504] ======== dhd_wlan_init_plat_data ========
[   40.989626] dhd_wlan_init_gpio: GPIO(WL_REG_ON) = -1
[   40.994754] dhd_wlan_init_gpio: GPIO(WL_HOST_WAKE) = -1
[   41.000063] dhd_wlan_init_gpio: host_oob_irq: 100
[   41.004927] dhd_wlan_init_gpio: host_oob_irq_flags=0x414
[   55.385551] ======== dhd_wlan_deinit_plat_data ========
[   55.399437] ======== dhd_wlan_init_plat_data ========
[   55.406001] dhd_wlan_init_gpio: GPIO(WL_REG_ON) = -1
[   55.412421] dhd_wlan_init_gpio: GPIO(WL_HOST_WAKE) = -1
[   55.418709] dhd_wlan_init_gpio: host_oob_irq: 100
[   55.424961] dhd_wlan_init_gpio: host_oob_irq_flags=0x414
[   69.631380] ======== dhd_wlan_deinit_plat_data ========
[   69.780403] ======== dhd_wlan_init_plat_data ========
[   69.794767] dhd_wlan_init_gpio: GPIO(WL_REG_ON) = -1
[   69.809041] dhd_wlan_init_gpio: GPIO(WL_HOST_WAKE) = -1
[   69.823197] dhd_wlan_init_gpio: host_oob_irq: 100
[   69.837174] dhd_wlan_init_gpio: host_oob_irq_flags=0x414
[   70.323227] wlan: loading driver v4.5.20.037
[   83.902800] ======== dhd_wlan_deinit_plat_data ========
[   83.916720] ======== dhd_wlan_init_plat_data ========
[   83.923267] dhd_wlan_init_gpio: GPIO(WL_REG_ON) = -1
[   83.929730] dhd_wlan_init_gpio: GPIO(WL_HOST_WAKE) = -1
[   83.929734] dhd_wlan_init_gpio: host_oob_irq: 100
[   83.929736] dhd_wlan_init_gpio: host_oob_irq_flags=0x414
[   90.734570] wlan: driver load failure
[   96.761044] ======== dhd_wlan_deinit_plat_data ========
[   96.761083] ======== dhd_wlan_init_plat_data ========
[   96.761087] dhd_wlan_init_gpio: GPIO(WL_REG_ON) = -1
[   96.761091] dhd_wlan_init_gpio: GPIO(WL_HOST_WAKE) = -1
[   96.761095] dhd_wlan_init_gpio: host_oob_irq: 100
[   96.761099] dhd_wlan_init_gpio: host_oob_irq_flags=0x414
[  108.841384] ======== dhd_wlan_deinit_plat_data ========
[  108.841422] ======== dhd_wlan_init_plat_data ========
[  108.841426] dhd_wlan_init_gpio: GPIO(WL_REG_ON) = -1
[  108.841430] dhd_wlan_init_gpio: GPIO(WL_HOST_WAKE) = -1
[  108.841434] dhd_wlan_init_gpio: host_oob_irq: 100
[  108.841438] dhd_wlan_init_gpio: host_oob_irq_flags=0x414
[  120.961724] ======== dhd_wlan_deinit_plat_data ========

 

Link to comment
Share on other sites

1 hour ago, balbes150 said:

Edit file /etc/modules  only line

 

aml_nftl_dev

wlan

 

 

Done

 

cat /etc/modules
aml_nftl_dev
#wifi_dummy
#cfg80211
#dhd
wlan

 

reboot


 

$ lsmod
Module                  Size  Used by
xt_addrtype             2923  2
zram                    8953  8
ch341                   5434  0
wlan                 3435325  0
cfg80211              415017  1 wlan
aml_nftl_dev           95108  0

$ dmesg | grep wlan
[    2.353259] Wifi: bcmdhd_init_wlan_mem: bcmdhd_init_wlan_mem: WIFI MEM Allocated
[   14.203544] wlan: loading driver v4.5.20.037
[   16.197644] android_readwrite_file: file /lib/firmware/wlan/wlan_mac.bin filp_open error
[   16.249362] wlan_logging_sock_activate_svc: Initalizing FEConsoleLog = 0 NumBuff = 32
[   16.249622] wlan_logging_sock_activate_svc: Activated wlan_logging svc
[   16.249744] wlan: driver loaded
[   16.461455] ======== dhd_wlan_init_plat_data ========
[   16.461459] dhd_wlan_init_gpio: GPIO(WL_REG_ON) = -1
[   16.461461] dhd_wlan_init_gpio: GPIO(WL_HOST_WAKE) = -1
[   16.461464] dhd_wlan_init_gpio: host_oob_irq: 100
[   16.461466] dhd_wlan_init_gpio: host_oob_irq_flags=0x414
[   35.511470] ======== dhd_wlan_deinit_plat_data ========
[   35.511511] ======== dhd_wlan_init_plat_data ========
[   35.511515] dhd_wlan_init_gpio: GPIO(WL_REG_ON) = -1
[   35.511519] dhd_wlan_init_gpio: GPIO(WL_HOST_WAKE) = -1
[   35.511523] dhd_wlan_init_gpio: host_oob_irq: 100
[   35.511526] dhd_wlan_init_gpio: host_oob_irq_flags=0x414
[   52.142211] ======== dhd_wlan_deinit_plat_data ========
[   52.142249] ======== dhd_wlan_init_plat_data ========
[   52.142253] dhd_wlan_init_gpio: GPIO(WL_REG_ON) = -1
[   52.142257] dhd_wlan_init_gpio: GPIO(WL_HOST_WAKE) = -1
[   52.142261] dhd_wlan_init_gpio: host_oob_irq: 100
[   52.142265] dhd_wlan_init_gpio: host_oob_irq_flags=0x414
[   68.782574] ======== dhd_wlan_deinit_plat_data ========
[   68.782612] ======== dhd_wlan_init_plat_data ========
[   68.782616] dhd_wlan_init_gpio: GPIO(WL_REG_ON) = -1
[   68.782620] dhd_wlan_init_gpio: GPIO(WL_HOST_WAKE) = -1
[   68.782624] dhd_wlan_init_gpio: host_oob_irq: 100
[   68.782628] dhd_wlan_init_gpio: host_oob_irq_flags=0x414
[   85.413033] ======== dhd_wlan_deinit_plat_data ========
[   85.464975] ======== dhd_wlan_init_plat_data ========
[   85.464981] dhd_wlan_init_gpio: GPIO(WL_REG_ON) = -1
[   85.464986] dhd_wlan_init_gpio: GPIO(WL_HOST_WAKE) = -1
[   85.464991] dhd_wlan_init_gpio: host_oob_irq: 100
[   85.464996] dhd_wlan_init_gpio: host_oob_irq_flags=0x414

 

didnt work, even if I launch modprobe wlan it wont work

 

strange only that configuration works


 

aml_nftl_dev
cfg80211
dhd
wlan #works with and without this the same way

 

the problem keeps fighting lol

 

thanks @balbes150, without your support I'm lost, this seems a bit tricky 

Link to comment
Share on other sites

On 27-2-2018 at 3:37 PM, kingontheroad said:

Hello

 

If i choose to install ubuntu , wich version can i best to choose for kodi , plex and ipvanisch ?
Mate or Server , i have the Beelink GT1 Ultimate 3gb/32gb .

Root and 1234 is the standard ? for inlog (armbian 5.41)

 

Friendly Regards , Richard

 

 

 

 

Nobody ? What i have read is the Armbian_5.41_S9xxx_Ubuntu_xenial_3.14.29_mate_20180225.img the rom i needed  .

But wich file must i chance (img.dbt ) ?? and what do i to login and password ?

Sorry for my english

 

Richard

Link to comment
Share on other sites

6 minutes ago, kingontheroad said:

Nobody ? What i have read is the Armbian_5.41_S9xxx_Ubuntu_xenial_3.14.29_mate_20180225.img the rom i needed  .

But wich file must i chance (img.dbt ) ?? and what do i to login and password ?

Sorry for my english

 

Richard

 

Hello

 

copy one dtb file to the root named as dtb.img

 

ex 

cp /boot/dtb-3.14.29/kvim2_multios.dtb /boot/dtb.img

 

login and password is un:root pw:1234 is in the docs

 

Link to comment
Share on other sites

4 minutes ago, kingontheroad said:

ex means as example ??

 

I can,t find cp /boot/dtb-3.14.29/kvim2_multios.dtb /boot/dtb.img on my micro sd card ?

 

4 minutes ago, kingontheroad said:

ex means as example ??

 

I can,t find cp /boot/dtb-3.14.29/kvim2_multios.dtb /boot/dtb.img on my micro sd card ?

 

inside of sdcard you have some folders like dtb, dtb-3.14.29, dtb-3.14.29.old, this folders has the dtbs files

 

you must copy one of that files to the root of sdcard but name it has dtb.img

 

tip: copy one that works with your device, if you know what file is, else try one by one

 

Im new here, and try to help with my limited knowledge of Armbian

Link to comment
Share on other sites

1 hour ago, kingontheroad said:

I have used dbt.img (gxm_q201_2g) 

 

Pasword log in is ok , but log in screen comes back ?

I really wanna help

But dont know how.

Do you try other dbt files?

Its strange

I think im using kvim2_linux.dtb and my box is same chiptset as yours. Amlogic s912

 

Send some fotos of login screen, and after login when it goês black. And more info about your setup

 

Good luck man, thanks

Link to comment
Share on other sites

@balbes150 can you helpevme one more time?

 

I have follow your instructions, but it wont work, I report it in above posts,

 

I try to put modprobe wlan in a root cronjob with @reboot but it dont work.....WiFi module is not initialized, I try a echo 123 > /tmp/123 in cronjob and it wont work too

 

Is the @reboot cron working on the armbian ?

 

Do you have any idea how can I resolve this problem on midprobe boot without manually type modprobe?

 

this is far from aceptable for any solid wifi setup. If it work with cronjob, for me is almost perfect ;)

 

Thanks in advance...

I dont have time to try other boot alternatives, maybe tomorrow I have time to explore other ways. But wifi is working and that is awesome. Thanks to you @balbes150

Link to comment
Share on other sites

14 hours ago, koakh said:

I really wanna help

But dont know how.

Do you try other dbt files?

Its strange

I think im using kvim2_linux.dtb and my box is same chiptset as yours. Amlogic s912

 

Send some fotos of login screen, and after login when it goês black. And more info about your setup

 

Good luck man, thanks

 

I have try yours kvim2_linux.dtb , but the same problem login screen comes back . i trying to make a hoal compleet new image , perhaps that wil be help...

I have a philips smart tv a beelink gt1 3gb/32gb and a chinees wireless i8 backlight keyboard

ubuntu.png

Link to comment
Share on other sites

19 hours ago, kingontheroad said:

 

I have try yours kvim2_linux.dtb , but the same problem login screen comes back . i trying to make a hoal compleet new image , perhaps that wil be help...

I have a philips smart tv a beelink gt1 3gb/32gb and a chinees wireless i8 backlight keyboard

ubuntu.png

hello

 

I never install a armbian with windowsmanager, I only install console/headless server version, Its all I need for my backend projects

 

I try to help. But Im not right person. Maybe some of experts comes and help you.....good luck, and dont vive up

Link to comment
Share on other sites

4 minutes ago, koakh said:

hello

 

I never install a armbian with widowsmanager, I only install console/headless server version, Its all I need for my backend projects

 

I try to help. But Im not right person. Maybe some of experts comes and help you.....good luck, and dont vive up

i hope so , thnx for your help

 

Link to comment
Share on other sites

46 minutes ago, balbes150 said:

Your problem is in bad media or incorrect initial settings (the system does not complete the correct initial setting).

My english is not so very good , but iam in ubuntu , i chance right up in from kodi to mate and i had succes :);) 
Now we can try play/install kodi , plec etc

Thnx for your help

 

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.
×
×
  • Create New...

Important Information

Terms of Use - Privacy Policy - Guidelines