soso1103 Posted January 24, 2018 Posted January 24, 2018 (edited) Hello everyone.. below is from a board with a bad flash, or download. Spoiler HELLO! BOOT0 is starting! boot0 version : 4.0.0 rtc[1] value = 0x00010000 rtc[2] value = 0x00020000 rtc[3] value = 0x00030000 DRAM DRIVE INFO: V1.0 DRAM Type =3 (2DR2,3DR3,6:LPDDR2,7:LPDDR3) DRAM normal_mode value: 00000001 DRAM CLK =720 MHZ PMU: AXP81X ddr voltage = 1500 mv using ic H8 using axp AXP818 DRAM zq value: 00003bfb dram size =2048 card boot number = 2 card no is 2 sdcard 2 line count 0 [mmc]: mmc driver ver 2014-8-11 15:06:39 [mmc]: ***Try SD card 2*** [mmc]: mmc 2 cmd 8 timeout, err 00000100 [mmc]: mmc 2 cmd 8 err 00000100 [mmc]: mmc 2 send if cond failed [mmc]: mmc 2 cmd 55 timeout, err 00000100 [mmc]: mmc 2 cmd 55 err 00000100 [mmc]: mmc 2 send app cmd failed [mmc]: ***Try MMC card 2*** [mmc]: MMC ver 5.0 [mmc]: SD/MMC Card: 4bit, capacity: 14910MB [mmc]: vendor: Man 00150100 Snr 004df7f4 [mmc]: product: AWPD3 [mmc]: revision: 5.2 [mmc]: ***SD/MMC 2 init OK!!!*** sdcard 2 init ok The size of uboot is 000d8000. sum=afc82dcd src_sum=afc82dcd set_mmc_para,sdly 50M 0 set_mmc_para,sdly 25M 0 Succeed in loading uboot from sdmmc flash. Ready to disable icache. Jump to secend Boot. [ 0.334] U-Boot 2011.09-rc1-00001-gb8627fb-dirty (Sep 02 2016 - 09:17:56) Allwinner Technology [ 0.344]version: 2.1.0 normal mode [ 0.419]pmbus: normal or secure os ready [ 0.424]PMU: AXP81X [ 0.426]PMU: AXP81X found bat_vol=385, ratio=100 [ 0.431]PMU: dcdc2 900 [ 0.434]PMU: pll1 1008 Mhz AXI0=336 Mhz,PLL_PERIPH =1200 Mhz AHB1=200 Mhz, APB1=100 Mhz set power on vol to default dcdc1_vol = 3000, onoff=1 dcdc2_vol = 900, onoff=1 dcdc3_vol = 900, onoff=1 dcdc4_vol = 900, onoff=1 dcdc6_vol = 900, onoff=1 aldo1_vol = 1800, onoff=1 aldo2_vol = 1800, onoff=1 aldo3_vol = 3000, onoff=1 fldo2_vol = 900, onoff=1 dldo1_vol = 3300, onoff=0 eldo2_vol = 1800, onoff=0 find power_sply to end supply=dcdc1 axp=axp81x, supply=dcdc1, vol=3000 reg addr=0x1c20b04, value=0xa, pmu_vol=3000 supply=dcdc1 axp=axp81x, supply=dcdc1, vol=3000 reg addr=0x1c20b08, value=0xa, pmu_vol=3000 supply=dldo4 axp=axp81x, supply=dldo4, vol=3000 reg addr=0x1c20b0c, value=0xa, pmu_vol=3000 supply=dcdc1 axp=axp81x, supply=dcdc1, vol=3000 reg addr=0x1c20b10, value=0xa, pmu_vol=3000 supply=dcdc1 axp=axp81x, supply=dcdc1, vol=3000 reg addr=0x1c20b14, value=0xa, pmu_vol=3000 supply=dcdc1 axp=axp81x, supply=dcdc1, vol=3000 reg addr=0x1c20b18, value=0xa, pmu_vol=3000 supply=dcdc1 axp=axp81x, supply=dcdc1, vol=3000 reg addr=0x1c20b1c, value=0xa, pmu_vol=3000 supply=aldo3 axp=axp81x, supply=aldo3, vol=3000 reg addr=0x1f02f00, value=0xa, pmu_vol=3000 config gpio bias voltage finish vbus exist no battery, limit to dc ac100 reg 0x00 = 0x101 ac100 reg 0xd0 = 0x0 ac100 reg 0xd1 = 0x0 fel key old mode run key detect no key found no key input dram_para_set start dram_para_set end [ 1.149]DRAM: 2 GiB relocation Offset is: 75af5000 gic: normal or no secure os mode script config pll_de to 504 Mhz script config pll_video1 to 297 Mhz Not Found clk pll_video in script DRV_DISP_Init end [ 1.356]fetch script data boot_disp.output_disp fail [ 1.361]boot_disp.output_type=1 [ 1.364]fetch script data boot_disp.output_mode fail [ 1.369]boot_disp.auto_hpd=0 disp0 device type(1) enable disp 0, clk: pll(560000000),clk(560000000),dclk(140000000) dsi_rate(140000000) clk realll(558000000),clk(0),dclk(0) dsi_rate(139500000) enable power axp81x_aldo1, ret=0 enable power axp81x_eldo2, ret=0 enable power axp81x_dc1sw, ret=0 workmode = 0 MMC: 2 [ 1.675][mmc]: mmc driver ver 2015-12-03 21:17:15 [ 1.680][mmc]: get sdc_phy_wipe fail. [ 1.776][mmc]: get sdc0 sdc_erase fail. [ 1.780][mmc]: get sdc_2xmode ok, val = 1 [ 1.784][mmc]: get sdc_ddrmode ok, val = 1 [ 1.788][mmc]: get sdc_f_max fail,use default 50000000Hz [ 1.794][mmc]: get card_line ok, card_line = 8 [ 1.798][mmc]: get sdc_ex_dly_used fail,use default [ 1.803][mmc]: SUNXI SD/MMC: 2 [ 1.808][mmc]: mmc_config_clock: clk 400000 [ 1.823][mmc]: *Try SD card 2* [ 1.828][mmc]: mmc 2 cmd 8 err 100 [ 1.834][mmc]: mmc send if cond failed [ 1.839][mmc]: mmc 2 cmd 55 err 100 [ 1.845][mmc]: send app cmd failed [ 1.848][mmc]: *Try MMC card 2* [ 1.899][mmc]: mmc_config_clock: clk 25000000 [ 1.913][mmc]: mmc re-update_phase [ 1.920][mmc]: mmc re-update_phase [ 1.927][mmc]: mmc re-update_phase [ 1.932][mmc]: ddr8 [ 1.936][mmc]: mmc re-update_phase [ 1.943][mmc]: mmc_config_clock: clk 25000000 [ 1.953][mmc]: mmc_config_clock: clk 50000000 [ 1.959][mmc]: CID 0x15010041 0x57504433 0x52004df7 0xf4848307 [ 1.964][mmc]: MMC ver 5.0 [ 1.967][mmc]: mmc clk 50000000 [ 1.970][mmc]: SD/MMC Card: 8bit, capacity: 14910MB [ 1.976][mmc]: boot0 capacity: 4000KB,boot1 capacity: 4000KB [ 1.981][mmc]: ***SD/MMC 2 init OK!!!*** [ 1.986][mmc]: erase_grp_size:0x400WrBlk * 0x200 = 0x80000 Byte [ 1.992][mmc]: secure_feature 0x55 [ 1.995][mmc]: secure_removal_type 0x9 [ 1.999]sunxi flash init ok read item0 copy0 Item0 (Map) magic is bad the secure storage item0 copy0 is bad read item0 copy1 Item0 (Map) magic is bad the secure storage item0 copy0 == copy1, the data is good the secure storage map is empty no item name key_burned_flag in the map sunxi secure storage has no flag [ 2.029]usb burn from boot delay time 0 [ 2.100]usb prepare ok usb sof ok [ 2.290]usb probe ok [ 2.292]usb setup ok set address 0x8 [ 5.294]timer occur [ 5.329]do_burn_from_boot usb : have no handshake In: serial Out: serial Err: serial --------fastboot partitions-------- -total partitions:13- -name- -start- -size- bootloader : 1000000 1000000 env : 2000000 1000000 boot : 3000000 1000000 system : 4000000 30000000 misc : 34000000 1000000 recovery : 35000000 2000000 private : 37000000 1000000 Reserve0 : 38000000 1000000 Reserve1 : 39000000 2000000 Reserve2 : 3b000000 1000000 cache : 3c000000 28000000 media_data : 64000000 1000000 UDISK : 65000000 0 ----------------------------------- base bootcmd=run setargs_nand boot_normal bootcmd set setargs_mmc key 0 cant find rcvy value cant find fstbt value misc partition found Recovery detected, will boot recovery to be run cmd=run setargs_mmc boot_recovery no item name mac in the map sunxi storage read fail check user data form private the user data'magic is bad ** Unable to read "ULI/factory/snum.txt" from sunxi_flash 6:0 ** load file(ULI/factory/snum.txt) error serial is: 200000f10200a7180b09 mount part name bootloader cant open script.bin, maybe it is not exist WORK_MODE_BOOT board_status_probe [ 5.455]power trigger bat_exist=0 [ 5.458]no battery exist sunxi_bmp_logo_display [ 5.568]fetch script data boot_disp.output_disp fail [ 5.573]screen_id =0, screen_width =1080, screen_height =1920 [ 5.579]frame buffer address 46400036 [ 5.583]gd->fb_base address 46400000 [ 5.587]Hit any key to stop autoboot: 0 read boot or recovery all [ 5.661]sunxi flash read :offset 35000000, 5848786 bytes OK [ 5.672]ready to boot [ 5.675][mmc]: mmc exit start [ 5.679][mmc]: mmc_config_clock: clk 50000000 [ 5.683][mmc]: mmc_config_clock: clk 400000 [ 5.699][mmc]: mmc 2 cmd 8 err 100 [ 5.705][mmc]: mmc send if cond failed [ 5.710][mmc]: mmc 2 cmd 55 err 100 [ 5.716][mmc]: send app cmd failed [ 5.733][mmc]: get sdc_phy_wipe fail. [ 5.737][mmc]: get sdc0 sdc_erase fail. [ 5.741][mmc]: get sdc_2xmode ok, val = 1 [ 5.745][mmc]: get sdc_ddrmode ok, val = 1 [ 5.749][mmc]: get sdc_f_max fail,use default 50000000Hz [ 5.755][mmc]: get card_line ok, card_line = 8 [ 5.759][mmc]: get sdc_ex_dly_used fail,use default [ 5.764][mmc]: mmc 2 exit ok [ 5.767] Starting kernel ... undefined instruction pc : [<80008004>] lr : [<bfafa3b4>] sp : b29fd390 ip : 00000007 fp : b3a1b0d0 r10: 00000000 r9 : b3a1a2c0 r8 : b29fff14 r7 : b3a1a3e8 r6 : 40007840 r5 : b29fffe4 r4 : 00000000 r3 : 80008000 r2 : 40000100 r1 : 00001029 r0 : 00000000 Flags: nZCv IRQs off FIQs off Mode SVC_32 Holding for test mode Edited January 25, 2018 by Tido added spoiler + code box
Tido Posted January 24, 2018 Posted January 24, 2018 this is a valid question. How would u help if u read your post?
guidol Posted January 24, 2018 Posted January 24, 2018 which Allwinner board is this and which OS-image did you use?
soso1103 Posted January 24, 2018 Author Posted January 24, 2018 it a Allwinner H8 octa core, V6-H8-V1.0 2016-09-02 ARM CORTEX A17 The firmware is ( homlet4.4.2-h8-v1.0 ) (kernal 3.4.39 ) OS Nibiru 2.00.000 verVR0069/20161009122814 gpu SGX544MP1 On the board there a sticker here is what I got V6-V1.0 16G/2G NB900 101-0V6FF00ECA2A SP1610006 102 It a VR all in one, a Vr headset, that has a built in lcd.. so no need for smartphone.. Thanks for the reply, if there any info you need please just ask.. I have the full specs of the device also.
soso1103 Posted January 24, 2018 Author Posted January 24, 2018 1 hour ago, Tido said: this is a valid question. How would u help if u read your post? I wouldn't have an answer, I don't know what I looking at, that is why im here. I hopeing someone can look at this and see where something went wrong, the device keeps stalling on boot image. But I see what your saying though..
Igor Posted January 25, 2018 Posted January 25, 2018 Probably the only way to bring it back to life is to reflash it with a stock Phoenix tools/firmware. A80 is not very well supported so there aren't any alternatives ... some very basic mainline support exists, but that's all.
soso1103 Posted January 25, 2018 Author Posted January 25, 2018 10 hours ago, Igor said: Probably the only way to bring it back to life is to reflash it with a stock Phoenix tools/firmware. A80 is not very well supported so there aren't any alternatives ... some very basic mainline support exists, but that's all. Thanks Iqor, Yes going to have to reflash, the only problem is, the pc only detects the device when it fully boots up into the OS. I can get in download mode, and I did get the info above by UART, but adb, and Phoenix tools, don't detect the device.. Thank you.. very much..
Recommended Posts