balbes150 Posted August 27, 2021 Posted August 27, 2021 Good news. Full-fledged working images (20210827) of ArmbianTV for P2 and M2 are ready. All the equipment works in them and you can start and configure the system via an HDMI monitor and a keyboard/mouse. M2 https://disk.yandex.ru/d/OBDO8BU2y1M6ug https://users.armbian.com/balbes150/rk3566/ P2 https://disk.yandex.ru/d/neKXsYolKXgLzg https://users.armbian.com/balbes150/rk3568/ 2
FJOtero Posted August 31, 2021 Posted August 31, 2021 ¡Great job, balbes150! Thank you, all System goes fine, and I am writing this from the Station P2. Some details, I'm searching solutions for, but prefer to tell: a) on boot, HDMI goes well, but colors are mixed. If I unplug & replug hdmi, this situation disapears, don't know why yet. b) tried to pass system boot to emmc, twice, appears a /nand-sata-install.jusNh3 empty. Besides lsblk shows mmcblk0boot0 & mmcblk0boot1, can't mount it: mount: /mnt/mmcblk0boot1: wrong fs type, bad option, bad superblock on /dev/mmcblk0boot1, missing codepage or helper program, or other error. If I find anything, I'll write back that. Best regards, well done! Francisco
balbes150 Posted September 1, 2021 Author Posted September 1, 2021 20 часов назад, FJOtero сказал: ¡Great job, balbes150! Thank you, all System goes fine, and I am writing this from the Station P2. Some details, I'm searching solutions for, but prefer to tell: a) on boot, HDMI goes well, but colors are mixed. If I unplug & replug hdmi, this situation disapears, don't know why yet. b) tried to pass system boot to emmc, twice, appears a /nand-sata-install.jusNh3 empty. Besides lsblk shows mmcblk0boot0 & mmcblk0boot1, can't mount it: mount: /mnt/mmcblk0boot1: wrong fs type, bad option, bad superblock on /dev/mmcblk0boot1, missing codepage or helper program, or other error. If I find anything, I'll write back that. Best regards, well done! The current version does not support installation in eMMC. Do not try to do this.
FJOtero Posted September 2, 2021 Posted September 2, 2021 Thanks for telling so clear. I tried before your warning. Lost access to config pressing reset before power-up. So my mistake perhaps will be useful to prevent this for others. Thanks a lot, balbes150!!
redjr Posted September 6, 2021 Posted September 6, 2021 On 8/27/2021 at 5:43 AM, balbes150 said: Good news. Full-fledged working images (20210827) of ArmbianTV for P2 and M2 are ready. All the equipment works in them and you can start and configure the system via an HDMI monitor and a keyboard/mouse. M2 https://disk.yandex.ru/d/OBDO8BU2y1M6ug https://users.armbian.com/balbes150/rk3566/ P2 https://disk.yandex.ru/d/neKXsYolKXgLzg https://users.armbian.com/balbes150/rk3568/ Thank you so much for this. I now have my Station P2 up and running Armbian. I for one appreciate all the work you do with these new SBCs and variants of Linux/Armbian. Thanks again! Rick
redjr Posted September 9, 2021 Posted September 9, 2021 @balbes150, Do your images support an m.2 SSD? I can't seem to get Linux to recognize mine. Using lsblk it does not show up. Rick
CryBaby Posted September 11, 2021 Posted September 11, 2021 Thank you balbes150, my P2 is running nicely with your image. I would like to get DVB running too but the modules don't seem to be included (my DVB tuner is listed by lsusb). So i'm trying to build the kernel myself. I am following https://docs.armbian.com/Developer-Guide_Build-Preparation/ using https://github.com/150balbes/build but it doesn't offer any rk3568 kernel options. What else should I be doing?
Igor Posted September 11, 2021 Posted September 11, 2021 5 hours ago, CryBaby said: What else should I be doing? Supporting his / our work? https://docs.armbian.com/User-Guide_FAQ/#development-time
balbes150 Posted September 14, 2021 Author Posted September 14, 2021 09.09.2021 в 16:00, redjr сказал: Do your images support an m.2 SSD? I can't seem to get Linux to recognize mine. Using lsblk it does not show up. I connected the NVMe module to P2 , the system sees it and can work with it. Which image and which DTB are you using ? Here is the output of "fdisk -l", which clearly shows the presence of NVMe in the system. Disk /dev/nvme0n1: 119.24 GiB, 128035676160 bytes, 250069680 sectors Disk model: NE-128 Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Armbian 21.11.0-trunk Hirsute ttyFIQ0 station-m2 login: root Password: ____ _ _ _ __ __ ____ / ___|| |_ __ _| |_(_) ___ _ __ | \/ |___ \ \___ \| __/ _` | __| |/ _ \| '_ \ | |\/| | __) | ___) | || (_| | |_| | (_) | | | | | | | |/ __/ |____/ \__\__,_|\__|_|\___/|_| |_| |_| |_|_____| Welcome to Armbian 21.11.0-trunk Hirsute with Linux 4.19.193 No end-user support: built from trunk System load: 62% Up time: 0 min Memory usage: 6% of 3.68G IP: 192.168.1.39 CPU temp: 30�°C Usage of /: 32% of 15G [ 2 security updates available, 7 updates total: apt upgrade ] Last check: 2021-09-08 14:13 Last login: Wed Sep 8 14:13:42 UTC 2021 on ttyFIQ0 root@station-m2:~# fdisk -l Disk /dev/ram0: 4 MiB, 4194304 bytes, 8192 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk /dev/mtdblock0: 32 MiB, 33554432 bytes, 65536 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk /dev/mmcblk0: 29.12 GiB, 31268536320 bytes, 61071360 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: gpt Disk identifier: 1E020000-0000-406A-8000-113E00001CED Device Start End Sectors Size Type /dev/mmcblk0p1 16384 24575 8192 4M unknown /dev/mmcblk0p2 24576 32767 8192 4M unknown /dev/mmcblk0p3 32768 40959 8192 4M unknown /dev/mmcblk0p4 40960 49151 8192 4M unknown /dev/mmcblk0p5 49152 51199 2048 1M unknown /dev/mmcblk0p6 51200 116735 65536 32M unknown /dev/mmcblk0p7 116736 124927 8192 4M unknown /dev/mmcblk0p8 124928 321535 196608 96M unknown /dev/mmcblk0p9 321536 1107967 786432 384M unknown /dev/mmcblk0p10 1107968 1894399 786432 384M unknown /dev/mmcblk0p11 1894400 1927167 32768 16M unknown /dev/mmcblk0p12 1927168 8300543 6373376 3G unknown /dev/mmcblk0p13 8300544 9349119 1048576 512M unknown /dev/mmcblk0p14 9349120 61071326 51722207 24.7G unknown Disk /dev/mmcblk1: 14.87 GiB, 15962472448 bytes, 31176704 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: gpt Disk identifier: BE4EF038-2CF8-46BD-8D6E-05E4769B6502 Device Start End Sectors Size Type /dev/mmcblk1p1 32768 65535 32768 16M Linux filesystem /dev/mmcblk1p2 65536 30834687 30769152 14.7G EFI System Disk /dev/nvme0n1: 119.24 GiB, 128035676160 bytes, 250069680 sectors Disk model: NE-128 Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes root@station-m2:~#
balbes150 Posted September 15, 2021 Author Posted September 15, 2021 New version of images 20210915-edge with 5.15.0-rc1 kernel. Please note, this version does not have an HDMI output, control is performed via SSH or UART. The wired network works, both LAN1 and LAN2 interfaces work on P2, M2 - LAN1. Please note that this is the primary test version and unpredictable behaviors are possible. 1
balbes150 Posted September 20, 2021 Author Posted September 20, 2021 New version 20210920 with support for installation in eMMC\NVMe\SATA. For details of the use, see the corresponding topics. m2 https://bbs.stationpc.com/thread-211-2-1.html p2 https://bbs.stationpc.com/thread-209-1-1.html
balbes150 Posted September 21, 2021 Author Posted September 21, 2021 Added version 20210921-edge with the 5.15.0-rc2 kernel and with the new u-boot.
balbes150 Posted October 18, 2021 Author Posted October 18, 2021 in industrial design https://wiki.t-firefly.com/en/EC-R3566PC/started.html https://wiki.t-firefly.com/en/EC-A3568J/started.html
chinhhut Posted October 24, 2021 Posted October 24, 2021 @balbes150 At first I'd like to thank you for your great work to make armbian work on many Android boxes. I have an X96 X6 Android box which based on RK3566. I've tried to use your latest M2 rk3566 image but there it could not be boot successfully.
balbes150 Posted October 24, 2021 Author Posted October 24, 2021 4 часа назад, chinhhut сказал: I have an X96 X6 Android box which based on RK3566. Only Station M2 P2 is discussed in this topic. If you want to have Armbian on rk35xx, use proven hardware. With your TV box, you need to contact the manufacturer or seller from whom you bought it.
chinhhut Posted October 24, 2021 Posted October 24, 2021 19 minutes ago, balbes150 said: Only Station M2 P2 is discussed in this topic. If you want to have Armbian on rk35xx, use proven hardware. With your TV box, you need to contact the manufacturer or seller from whom you bought it. I got it. There is no option to delete my previous post so I just removed the unrelated content to Station M2 P2. Thank you.
balbes150 Posted November 25, 2021 Author Posted November 25, 2021 Update version 20211124 with legacy kernel. p.s. Now I am testing a new image with a 5.16.rc2 kernel, in which HDMI and USB work. After all checks are completed, new versions of images with a new kernel will be available. 1
balbes150 Posted November 25, 2021 Author Posted November 25, 2021 Images 20211125-edge with 5.16-rc2 kernel for Station P2. It works with HDMI, USB (except the upper USB 2.0 port), LAN1, LAN2 https://disk.yandex.ru/d/gpd4Ayd0Qfpg6A
LocationUnknown Posted November 26, 2021 Posted November 26, 2021 Do the Armbian_21.11.0-trunk_Station-p2_bullseye_edge_5.16.0_xfce_desktop boot with working hdmi? Do they boot from tf card or do they need to be flashed to the device? Are the 5.16.0 images the same as the 5.16-rc2 images ? Thanks for all your hard work. For me the 5.16.0 images did not boot via hdmi but I do not have the cable to check via serial port at the moment and do not know how to properly get logs. I was trying to boot via tf card flashed via balena etcher. I have a station p2 8gb model.
balbes150 Posted November 26, 2021 Author Posted November 26, 2021 3 часа назад, LocationUnknown сказал: For me the 5.16.0 images did not boot via hdmi but I do not have the cable to check via serial port at the moment and do not know how to properly get logs. I was trying to boot via tf card flashed via balena etcher. I have a station p2 8gb model. Everything works from an SD card. But to run, you must have the bootloader updated in eMMC. The order of how to do this is described at this link (mesenge 2021-9-20 19:05:26) https://bbs.stationpc.com/forum.php?mod=viewthread&tid=209&extra=page%3D1%26filter%3Dauthor%26orderby%3Dlastpost To check that you have updated the bootloader correctly, check the launch of the legacy kernel version (4.19) from the beginning. If you have previously used your SD card for other images, perform a complete cleaning of the SD card with the DD command to remove all dirt from the previous systems.
balbes150 Posted November 26, 2021 Author Posted November 26, 2021 Added images 20211126-edge with 5.16 kernel (work HDMI USB LAN) for Station M2. https://disk.yandex.ru/d/W1tihbpELodXEQ 1
DMC Posted November 26, 2021 Posted November 26, 2021 1 hour ago, balbes150 said: Added images 20211126-edge with 5.16 kernel (work HDMI USB LAN) for Station M2. https://disk.yandex.ru/d/W1tihbpELodXEQ Great news!
dieselnutjob Posted November 26, 2021 Posted November 26, 2021 5 hours ago, balbes150 said: Added images 20211126-edge with 5.16 kernel (work HDMI USB LAN) for Station M2. https://disk.yandex.ru/d/W1tihbpELodXEQ Is this the source code for this latest image https://github.com/150balbes/build/tree/station-x2 ? or is a different branch? thanks
balbes150 Posted November 27, 2021 Author Posted November 27, 2021 16 часов назад, dieselnutjob сказал: Is this the source code for this latest image https://github.com/150balbes/build/tree/station-x2 ? or is a different branch? At the moment, the developers have not yet made a decision on how to properly organize support for rk356x, so I am not sending changes to the build system yet. https://github.com/armbian/build/pull/3275
LocationUnknown Posted December 1, 2021 Posted December 1, 2021 Using the 5.16 build I was finally able to a working uart log reader. Here are my logs from the UART port. I could not get the port from the serial/rj45 to get readable logs. Through the uart terminal using minicom I was able to login and go through the user/root setup like normal and the system does boot. It just seems to me there is still a issue with the hdmi. Thank you for your efforts and I hope this helps. I am using the station p2 by the way. The link is a pastbin of the full bootup until the login and the quoted error is the the only error in the log I could see. I am booting from the tf card if that matters. I have already updated the uboot too. https://zerobin.net/?8b0d1e0e3de2e359#CrJefubSkdktCEG5pxf1lYOGwdfkqPuQjOD8GT781tE= 5.068486] rockchip-drm display-subsystem: [drm] *ERROR* POST_BUF_EMPTY irq err at vp0 [ 5.068500] rockchip-drm display-subsystem: [drm] *ERROR* POST_BUF_EMPTY irq err at vp0 [ 5.068511] rockchip-drm display-subsystem: [drm] *ERROR* POST_BUF_EMPTY irq err at vp0 [ 5.068521] rockchip-drm display-subsystem: [drm] *ERROR* POST_BUF_EMPTY irq err at vp0 [ 5.068531] rockchip-drm display-subsystem: [drm] *ERROR* POST_BUF_EMPTY irq err at vp0 [ 5.068542] rockchip-drm display-subsystem: [drm] *ERROR* POST_BUF_EMPTY irq err at vp0 [ 5.068552] rockchip-drm display-subsystem: [drm] *ERROR* POST_BUF_EMPTY irq err at vp0 [ 5.068562] rockchip-drm display-subsystem: [drm] *ERROR* POST_BUF_EMPTY irq err at vp0 [ 5.068573] rockchip-drm display-subsystem: [drm] *ERROR* POST_BUF_EMPTY irq err at vp0 [ 5.068583] rockchip-drm display-subsystem: [drm] *ERROR* POST_BUF_EMPTY irq err at vp0
balbes150 Posted December 2, 2021 Author Posted December 2, 2021 15 часов назад, LocationUnknown сказал: Using the 5.16 build I was finally able to a working uart log reader. Here are my logs from the UART port. I could not get the port from the serial/rj45 to get readable logs. Through the uart terminal using minicom I was able to login and go through the user/root setup like normal and the system does boot. It just seems to me there is still a issue with the hdmi. Thank you for your efforts and I hope this helps. I am using the station p2 by the way. The link is a pastbin of the full bootup until the login and the quoted error is the the only error in the log I could see. I am booting from the tf card if that matters. I have already updated the uboot too. VOP update mode to: 3840x2160p0, type: HDMI0 for VP0 Judging by the log, you have 4k TV. This permission is not supported. so far, only the 1920 x 1080 option is working. Please note, I have already written that HDMI support is a very early version that cannot fully work. Also in the log, I see that you do not have a wired LAN connection, there is no IP address for networks. Without this, you will not be able to use an SSH connection. Are you sure you have a P2 model? Show a photo of how the wire is connected to the LAN network card on your device.
Recommended Posts