fabiobassa Posted August 2, 2023 Posted August 2, 2023 This board Is very well supported, It was the first I have investigated. It doesn t start because Is not founding the rootfs You MUST use any image with LEGACY KERNEL 4.4.XXX 0 Quote
sadp Posted August 2, 2023 Posted August 2, 2023 (edited) Hello guys, first of all thank you @jock, @fabiobassa and other people for this amazing rk322x project. I ordered myself few of these cheap boxes. Few days ago one box came. It looks like that i got same box as @TU-Student I read all the instructions and a lot of posts on this forum about how I should backup Android and boot Linux. I understand that "Multitool" is the swiss knife, but for some reason this TV Box does not boot from SD card and the tool does not load, i only get orange LED on box and no signal (blackscreen). I cannot test anything because box does not boot backup tool, and I cant backup eMMC/eMCP and try to flash Armbian build. From what I have found this TV Box has: SOC CHIP Rockchip RK3229 r0p5 WIFI CHIP AP6210 EMMC MICRON Q2J95T 8GB RAM 1GB It has fake android 7.1 (10.0), android kernel is very old 3.10.104, boots only at 720p resolution, but kernel and build itself is freshly made in 20230606 signed with test-keys. What else can I do to make this boot from SD Card and load Multitool? How to make flash storage snapshot with android and flash armbian manually if I cannot use multitool. Please help Quote <br /> Quote Edited August 2, 2023 by sadp 1 Quote
YanCorote Posted August 2, 2023 Posted August 2, 2023 (edited) @jock@fabiobassa @RaptorSDSafter using the legacy kernel and the minimal version it even started to install but this error appeared: [FAILED] Failed to start Entropy Daemon based on the HAVEGE algorithm. See 'systemct status haveged.service' for details. Edited August 2, 2023 by YanCorote need help 0 Quote
n3o Posted August 2, 2023 Posted August 2, 2023 (edited) Spoiler On 3/5/2023 at 7:11 AM, RaptorSDS said: yes red are UART please use 3,3V on you ch341 adapter rx tx should be cross --> , tx form usb to rx from board , and rx from usb to tx from board , GND to GND you can not break anything with change of Baud rate , try both and you are fine the text that run automaticlly on UART is the serial log , when nothing or only some unreadable thing is show in putty please change baudrate than copy the text from putty or other tool and post here for jock , also ANdroid will produce a log on UART ( with some diffirence) many of this serial log also in android terminal demsg log i dont know the usb port order , for multitool over USB the port is normally irrelevant ,some box need normal USB , some the USB otg , some box hasnt the usb otg hi, sorry for the late, I have finally linked ch341 programmer to uart ... here is the log Spoiler [ 5.816610] ehci-platform 30100000.ehci2: irq 98, io mem 0x30100000 [ 5.833839] ehci-platform 30100000.ehci2: USB 2.0 started, EHCI 1.00 [ 5.834003] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 [ 5.834034] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.834060] usb usb3: Product: EHCI Host Controller [ 5.834084] usb usb3: Manufacturer: Linux 3.10.104 ehci_hcd [ 5.834108] usb usb3: SerialNumber: 30100000.ehci2 [ 5.834938] hub 3-0:1.0: USB hub found [ 5.835001] hub 3-0:1.0: 1 port detected [ 5.835783] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 5.836051] ohci-platform: OHCI generic platform driver [ 5.836292] ohci-platform 300a0000.ohci0: Generic Platform OHCI controller [ 5.836344] ohci-platform 300a0000.ohci0: new USB bus registered, assigned bus number 4 [ 5.836427] ohci-platform 300a0000.ohci0: irq 49, io mem 0x300a0000 [ 5.896881] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 5.896930] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.896957] usb usb4: Product: Generic Platform OHCI controller [ 5.896981] usb usb4: Manufacturer: Linux 3.10.104 ohci_hcd [ 5.897006] usb usb4: SerialNumber: 300a0000.ohci0 [ 5.897911] hub 4-0:1.0: USB hub found [ 5.897956] hub 4-0:1.0: 1 port detected [ 5.898410] ohci-platform 300e0000.ohci1: Generic Platform OHCI controller [ 5.898463] ohci-platform 300e0000.ohci1: new USB bus registered, assigned bus number 5 [ 5.898538] ohci-platform 300e0000.ohci1: irq 52, io mem 0x300e0000 [ 5.955898] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 [ 5.955947] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.955973] usb usb5: Product: Generic Platform OHCI controller [ 5.955998] usb usb5: Manufacturer: Linux 3.10.104 ohci_hcd [ 5.956023] usb usb5: SerialNumber: 300e0000.ohci1 [ 5.956858] hub 5-0:1.0: USB hub found [ 5.956903] hub 5-0:1.0: 1 port detected [ 5.957353] ohci-platform 30120000.ohci2: Generic Platform OHCI controller [ 5.957406] ohci-platform 30120000.ohci2: new USB bus registered, assigned bus number 6 [ 5.957486] ohci-platform 30120000.ohci2: irq 99, io mem 0x30120000 [ 6.014930] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 [ 6.014972] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.014998] usb usb6: Product: Generic Platform OHCI controller [ 6.015023] usb usb6: Manufacturer: Linux 3.10.104 ohci_hcd [ 6.015046] usb usb6: SerialNumber: 30120000.ohci2 [ 6.015890] hub 6-0:1.0: USB hub found [ 6.015934] hub 6-0:1.0: 1 port detected [ 6.016567] usbcore: registered new interface driver cdc_acm [ 6.016589] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 6.016719] usbcore: registered new interface driver usblp [ 6.016814] usbcore: registered new interface driver cdc_wdm [ 6.017043] usbcore: registered new interface driver usb-storage [ 6.017134] usbcore: registered new interface driver ums-alauda [ 6.017218] usbcore: registered new interface driver ums-cypress [ 6.017300] usbcore: registered new interface driver ums-datafab [ 6.017387] usbcore: registered new interface driver ums_eneub6250 [ 6.017469] usbcore: registered new interface driver ums-freecom [ 6.017563] usbcore: registered new interface driver ums-isd200 [ 6.017644] usbcore: registered new interface driver ums-jumpshot [ 6.017724] usbcore: registered new interface driver ums-karma [ 6.017805] usbcore: registered new interface driver ums-onetouch [ 6.017906] usbcore: registered new interface driver ums-sddr09 [ 6.017991] usbcore: registered new interface driver ums-sddr55 [ 6.018074] usbcore: registered new interface driver ums-usbat [ 6.018275] usbcore: registered new interface driver usbserial [ 6.018358] usbcore: registered new interface driver usbserial_generic [ 6.018423] usbserial: USB Serial support registered for generic [ 6.018517] usbcore: registered new interface driver option [ 6.018586] usbserial: USB Serial support registered for GSM modem (1-port) [ 6.019014] usbcore: registered new interface driver trancevibrator [ 6.019034] usb20_otg: version 3.10a 21-DEC-2012 [ 6.019981] e2680040 [ 6.020009] Core Release: 3.10a [ 6.020029] Setting default values for core params [ 6.020327] Using Buffer DMA mode [ 6.020348] Periodic Transfer Interrupt Enhancement - disabled [ 6.020366] Multiprocessor Interrupt Enhancement - disabled [ 6.020386] OTG VER PARAM: 0, OTG VER FLAG: 0 [ 6.020404] ^^^^^^^^^^^^^^^^^Device Mode [ 6.020431] Dedicated Tx FIFOs mode [ 6.020465] pcd_init otg_dev = dde4a340 [ 6.020878] usb20_otg 30040000.otg: DWC OTG Controller [ 6.020937] usb20_otg 30040000.otg: new USB bus registered, assigned bus number 7 [ 6.020995] usb20_otg 30040000.otg: irq 55, io mem 0x00000000 [ 6.021118] usb usb7: New USB device found, idVendor=1d6b, idProduct=0002 [ 6.021147] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.021170] usb usb7: Product: DWC OTG Controller [ 6.021194] usb usb7: Manufacturer: Linux 3.10.104 dwc_otg_hcd [ 6.021217] usb usb7: SerialNumber: 30040000.otg [ 6.022158] hub 7-0:1.0: USB hub found [ 6.022201] hub 7-0:1.0: 1 port detected [ 6.022782] usb20_host: version 3.10a 21-DEC-2012 [ 6.024776] usbcore: registered new interface driver xpad [ 6.024899] usbcore: registered new interface driver usb_acecad [ 6.025024] usbcore: registered new interface driver aiptek [ 6.025123] usbcore: registered new interface driver gtco [ 6.025222] usbcore: registered new interface driver hanwang [ 6.025319] usbcore: registered new interface driver kbtab [ 6.025448] usbcore: registered new interface driver wacom [ 6.025632] ==gsl_ts_init== [ 6.025713] ret=0 [ 6.025780] i2c-core: driver [gslX680] using legacy suspend method [ 6.025803] i2c-core: driver [gslX680] using legacy resume method [ 6.026661] sensor_register_slave:mma8452,id=17 [ 6.026685] sensor_register_slave:mma7660,id=18 [ 6.026703] sensor_register_slave:gs_mc3230,id=23 [ 6.026721] [Gsensor] gsensor_init [ 6.026741] sensor_register_slave:mpu6880_acc,id=24 [ 6.026761] sensor_register_slave:mpu6500_acc,id=25 [ 6.026780] sensor_register_slave:bma2xx_acc,id=26 [ 6.026799] sensor_register_slave:akm8963,id=30 [ 6.026818] sensor_register_slave:cm3217,id=51 [ 6.026836] sensor_register_slave:cm3218,id=52 [ 6.026854] sensor_register_slave:ls_stk3410,id=60 [ 6.027547] .. rk pwm remotectl v1.1 init [ 6.027641] ####################################### [ 6.027727] ################22222####################### [ 6.027794] ######################3333################# [ 6.027857] ########################4444############### [ 6.027915] #############################555########## [ 6.028277] input: 110b0030.pwm as /devices/110b0030.pwm/input/input0 [ 6.028955] remotectl-pwm 110b0030.pwm: Missing psci property in the DT. [ 6.119236] dwc_otg_hcd_suspend, usb device mode [ 6.665475] rtc_hym8563 0-0051: rtc core: registered hym8563 as rtc0 [ 6.665567] i2c /dev entries driver [ 6.666185] IR NEC protocol handler initialized [ 6.666217] IR RC5(x) protocol handler initialized [ 6.666235] IR RC6 protocol handler initialized [ 6.666253] IR JVC protocol handler initialized [ 6.666269] IR Sony protocol handler initialized [ 6.666287] IR RC5 (streamzap) protocol handler initialized [ 6.666305] IR SANYO protocol handler initialized [ 6.666322] IR MCE Keyboard/mouse protocol handler initialized [ 6.666674] usbcore: registered new interface driver uvcvideo [ 6.666696] USB Video Class driver (1.1.1) [ 6.666719] CamSys driver version: v0.35.0, CamSys head file version: v0.13.0 [ 6.666742] E:camsys_soc_init(36): camsys isn't support soc: 0x32283002! [ 6.667399] not find test_power_init dev node [ 6.667477] i2c-core: driver [bq27320] using legacy suspend method [ 6.667498] i2c-core: driver [bq27320] using legacy resume method [ 6.668818] ===========net_led_probe start=========== [ 6.668955] ===========net_led_probe end=========== [ 6.669196] ===========remote_led_probe start=========== [ 6.669296] ===========remote_led_probe end=========== [ 6.669534] ===========suspend_led_probe start=========== [ 6.669687] ===========suspend_led_probe end=========== [ 6.670077] rockchip_temp_probe,line=384 [ 6.670719] tsadc 11150000.tsadc: Missing tsadc_low_temp in the DT. [ 6.729236] tsadc 11150000.tsadc: initialized [ 6.730188] device-mapper: uevent: version 1.0.3 [ 6.730727] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com [ 6.731210] Bluetooth: HCI UART driver ver 2.2 [ 6.731238] Bluetooth: HCI H4 protocol initialized [ 6.731254] Bluetooth: HCILL protocol initialized [ 6.731273] rtk_btusb: RTKBT_RELEASE_NAME: 20170109_TV_ANDROID_6.x [ 6.731293] rtk_btusb: Realtek Bluetooth USB driver module init, version 4.1.2 [ 6.731313] rtk_btusb: Register usb char device interface for BT driver [ 6.731741] usbcore: registered new interface driver rtk_btusb [ 6.732161] cpufreq version 1.0, suspend freq 1008 MHz [ 6.732720] cpuidle: using governor ladder [ 6.732745] cpuidle: using governor menu [ 6.732822] Synopsys Designware Multimedia Card Interface Driver [ 6.732843] MHSC version = Ver 2.00 2015-06-10 [ 6.733386] dwmmc_rockchip 30020000.rksdmmc: Version ID is 270a [ 6.733481] dwmmc_rockchip 30020000.rksdmmc: failed to get hpclk_mmc [ 6.733933] dwmmc_rockchip 30020000.rksdmmc: Using internal DMA controller. [ 6.734293] dwmmc_rockchip 30020000.rksdmmc: dw_mci_init_slot: fmin=400000, fmax=125000000 [mmc0] [ 6.748979] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out 800000Hz for init[mmc0] [ 6.768751] dwmmc_rockchip 30020000.rksdmmc: DW MMC controller at irq 46, 32 bit host data width, 256 deep fifo [ 6.768795] dwmmc_rockchip 30020000.rksdmmc: 1 slots initialized [ 6.769519] dwmmc_rockchip 30000000.rksdmmc: Version ID is 270a [ 6.769614] dwmmc_rockchip 30000000.rksdmmc: failed to get hpclk_mmc [ 6.770070] dwmmc_rockchip 30000000.rksdmmc: Using internal DMA controller. [ 6.770445] dwmmc_rockchip 30000000.rksdmmc: dw_mci_init_slot: fmin=400000, fmax=37500000 [mmc1] [ 6.770747] dwmmc_rockchip 30000000.rksdmmc: mmc1: No udbg pinctrl found! [ 6.788335] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out 800000Hz for init[mmc1] [ 6.808166] dwmmc_rockchip 30000000.rksdmmc: DW MMC controller at irq 44, 32 bit host data width, 256 deep fifo [ 6.808242] dwmmc_rockchip 30000000.rksdmmc: 1 slots initialized [ 6.809400] dwmmc_rockchip 30010000.rksdmmc: Version ID is 270a [ 6.809542] dwmmc_rockchip 30010000.rksdmmc: failed to get hpclk_mmc [ 6.810140] dwmmc_rockchip 30010000.rksdmmc: Using internal DMA controller. [ 6.810711] dwmmc_rockchip 30010000.rksdmmc: dw_mci_init_slot: fmin=200000, fmax=37500000 [mmc2] [ 6.827718] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out 800000Hz for init[mmc2] [ 6.847539] dwmmc_rockchip 30010000.rksdmmc: DW MMC controller at irq 45, 32 bit host data width, 256 deep fifo [ 6.847612] dwmmc_rockchip 30010000.rksdmmc: 1 slots initialized [ 6.848277] leds-gpio power-led.31: pins are not configured from the driver [ 6.849258] hidraw: raw HID events driver (C) Jiri Kosina [ 6.856644] usbcore: registered new interface driver usbhid [ 6.856714] usbhid: USB HID core driver [ 6.857405] ashmem: initialized [ 6.857960] logger: created 256K log 'log_main' [ 6.858454] logger: created 256K log 'log_events' [ 6.858948] logger: created 256K log 'log_radio' [ 6.859435] logger: created 256K log 'log_system' [ 6.861709] rknandbase v1.1 2016-11-08 [ 6.862332] rknand 30030000.nandc: rknand_probe clk rate = 150000000 [ 6.862661] No.1 FLASH ID:2c 64 44 32 a5 0 [ 6.863300] ECC:60 [ 6.863363] FTL version: 5.0.47 20171120 [ 7.103190] Using Buffer DMA mode [ 7.103226] Periodic Transfer Interrupt Enhancement - disabled [ 7.103236] Multiprocessor Interrupt Enhancement - disabled [ 7.103248] OTG VER PARAM: 0, OTG VER FLAG: 0 [ 7.103259] ^^^^^^^^^^^^^^^^^^Host Mode [ 7.112384] FtlInit 0 [ 7.112707] uboot: 0x000400000 -- 0x000800000 (4 MB) [ 7.113300] trust: 0x000800000 -- 0x001000000 (8 MB) [ 7.113621] misc: 0x001000000 -- 0x001400000 (4 MB) [ 7.113916] baseparamer: 0x001400000 -- 0x001500000 (1 MB) [ 7.114214] resource: 0x001500000 -- 0x002400000 (15 MB) [ 7.114513] kernel: 0x002400000 -- 0x003000000 (12 MB) [ 7.114800] boot: 0x003000000 -- 0x003c00000 (12 MB) [ 7.115090] recovery: 0x003c00000 -- 0x005c00000 (32 MB) [ 7.115392] backup: 0x005c00000 -- 0x009c00000 (64 MB) [ 7.115713] cache: 0x009c00000 -- 0x011c00000 (128 MB) [ 7.116017] metadata: 0x011c00000 -- 0x012c00000 (16 MB) [ 7.116333] kpanic: 0x012c00000 -- 0x013000000 (4 MB) [ 7.116674] system: 0x013000000 -- 0x0d3000000 (3072 MB) [ 7.116992] userdata: 0x0d3000000 -- 0x1d4000000 (4112 MB) [ 7.121738] vendor storage 524b5644,2,2 [ 7.124603] vendor storage 524b5644,3,3 [ 7.129926] rockchip-spdif 100d0000.spdif: spdif ready. [ 7.152689] Init: Power Port (0) [ 7.152767] 30040000.otg resume, HPRT0:0x1000 [ 7.152892] 30040000.otg suspend, HPRT0:0x1000 [ 7.152903] rk322x-audio rockchip_audio.28: rk322x-hifi <-> 100b0000.i2s1 mapping ok [ 7.156962] rockchip-hdmi-i2s rockchip_hdmi_i2s.30: rk-hdmi-i2s-hifi <-> 100c0000.i2s0 mapping ok [ 7.157911] u32 classifier [ 7.157927] Actions configured [ 7.157943] Netfilter messages via NETLINK v0.30. [ 7.158032] nf_conntrack version 0.5.0 (15414 buckets, 61656 max) [ 7.158563] ctnetlink v0.93: registering with nfnetlink. [ 7.158662] NF_TPROXY: Transparent proxy support initialized, version 4.1.0 [ 7.158675] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd. [ 7.159207] xt_time: kernel timezone is -0000 [ 7.159551] ip_tables: (C) 2000-2006 Netfilter Core Team [ 7.159772] arp_tables: (C) 2002 David S. Miller [ 7.159839] TCP: cubic registered [ 7.159850] Initializing XFRM netlink socket [ 7.160271] NET: Registered protocol family 10 [ 7.161174] mip6: Mobile IPv6 [ 7.161235] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 7.161446] sit: IPv6 over IPv4 tunneling driver [ 7.162079] NET: Registered protocol family 17 [ 7.162126] NET: Registered protocol family 15 [ 7.162334] Bridge firewalling registered [ 7.162362] Ebtables v2.0 registered [ 7.162629] Bluetooth: RFCOMM TTY layer initialized [ 7.162683] Bluetooth: RFCOMM socket layer initialized [ 7.162696] Bluetooth: RFCOMM ver 1.11 [ 7.162709] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 7.162719] Bluetooth: BNEP filters: protocol multicast [ 7.162738] Bluetooth: BNEP socket layer initialized [ 7.162750] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 7.162765] Bluetooth: HIDP socket layer initialized [ 7.162858] l2tp_core: L2TP core driver, V2.0 [ 7.162882] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 7.162892] [WLAN_RFKILL]: Enter rfkill_wlan_init [ 7.163149] [WLAN_RFKILL]: Enter rfkill_wlan_probe [ 7.163168] [WLAN_RFKILL]: can't find rockchip,grf property [ 7.163180] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = rtl8189fs [ 7.163193] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control. [ 7.163204] [WLAN_RFKILL]: wlan_platdata_parse_dt: disable wifi io reference voltage control. [ 7.163217] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio. [ 7.163291] [WLAN_RFKILL]: wlan_platdata_parse_dt: get property: WIFI,poweren_gpio = 90, flags = 0. [ 7.163339] [WLAN_RFKILL]: wlan_platdata_parse_dt: get property: WIFI,host_wake_irq = 28, flags = 0. [ 7.163352] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio [ 7.163401] [WLAN_RFKILL]: rockchip_wifi_power: 0 [ 7.163415] [BT_RFKILL]: rfkill_get_bt_power_state: rfkill-bt driver has not Successful initialized [ 7.270445] [WLAN_RFKILL]: wifi shut off power. [ 7.270513] [WLAN_RFKILL]: rockchip_wifi_ref_voltage: 0 [ 7.270550] [WLAN_RFKILL]: rockchip_wifi_ref_voltage: wifi io reference voltage control is disabled. [ 7.280433] [WLAN_RFKILL]: rockchip_wifi_power: 1 [ 7.280484] [BT_RFKILL]: rfkill_get_bt_power_state: rfkill-bt driver has not Successful initialized [ 7.280522] [WLAN_RFKILL]: rockchip_wifi_ref_voltage: 1 [ 7.280553] [WLAN_RFKILL]: rockchip_wifi_ref_voltage: wifi io reference voltage control is disabled. [ 7.388598] [WLAN_RFKILL]: wifi turn on power. 90 [ 7.388655] mmc2:mmc host rescan start! [ 7.388702] [WLAN_RFKILL]: Exit rfkill_wlan_probe [ 7.388876] [BT_RFKILL]: Enter rfkill_rk_init [ 7.389758] Key type dns_resolver registered [ 7.394726] rk322x_suspend_init: pm_ctrbits = 0x11806 [ 7.394836] Registering SWP/SWPB emulation handler [ 7.394880] rockchip_uboot_mem_late_init: Freeing uboot logo memory: 0x02000000@0x9dc00000 [ 7.409683] ddrfreq: verion 1.2 20140526 [ 7.426062] ddrfreq: normal 600MHz performance 0MHz low_power 0MHz video_1080p 0MHz video_4k 700MHz dualview 0MHz idle 0MHz suspend 0MHz reboot 600MHz video_4k_10b 720MHz [ 7.426090] ddrfreq: auto-freq=0 [ 7.426106] ddrfreq: auto-freq-table epmty! [ 7.427757] regulator-dummy: disabling [ 7.428434] pcd_pullup, is_on 0 [ 7.428479] WARN::dwc_otg_handle_mode_mismatch_intr:69: Mode Mismatch Interrupt: currently in Host mode [ 7.428479] [ 7.428575] file system registered [ 7.430410] android_usb gadget: Mass Storage Function, version: 2009/09/11 [ 7.430435] android_usb gadget: Number of LUNs=2 [ 7.430453] lun0: LUN: removable file: (no medium) [ 7.430471] lun1: LUN: removable file: (no medium) [ 7.431085] android_usb gadget: android_usb ready [ 7.431216] sensor_init: Probe name sensors [ 7.431258] sensor-dev.c v1.4 add angle calculation support between two gsensors 2013-09-01 [ 7.471974] rtc_hym8563 0-0051: hctosys: invalid date/time [ 7.484392] rockchip-spdif-card rockchip_spdif_card.29: rk-hdmi-spdif-hifi <-> 100d0000.spdif mapping ok [ 7.485640] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 414; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '-v3.10.92-28033-gae45312', rk_ko_ver is '5', built at '17:38:20', on 'Aug 6 2018'. [ 7.485909] mali-utgard 20001000.gpu: mali_platform_device->num_resources = 13 [ 7.485933] mali-utgard 20001000.gpu: resource[0].start = 0x0x20001000 [ 7.485955] mali-utgard 20001000.gpu: resource[1].start = 0x0x20000000 [ 7.485975] mali-utgard 20001000.gpu: resource[2].start = 0x0x20003000 [ 7.485998] mali-utgard 20001000.gpu: resource[3].start = 0x0x20008000 [ 7.486018] mali-utgard 20001000.gpu: resource[4].start = 0x0x20004000 [ 7.486041] mali-utgard 20001000.gpu: resource[5].start = 0x0x2000a000 [ 7.486061] mali-utgard 20001000.gpu: resource[6].start = 0x0x20005000 [ 7.486083] mali-utgard 20001000.gpu: resource[7].start = 0x0x00000026 [ 7.486103] mali-utgard 20001000.gpu: resource[8].start = 0x0x00000025 [ 7.486124] mali-utgard 20001000.gpu: resource[9].start = 0x0x00000024 [ 7.486144] mali-utgard 20001000.gpu: resource[10].start = 0x0x00000025 [ 7.486166] mali-utgard 20001000.gpu: resource[11].start = 0x0x00000024 [ 7.486188] mali-utgard 20001000.gpu: resource[12].start = 0x0x00000025 [ 7.486266] mali-utgard 20001000.gpu: freq: 200000000, min_threshold: 0, max_threshold: 70 [ 7.486293] mali-utgard 20001000.gpu: freq: 300000000, min_threshold: 61, max_threshold: 85 [ 7.486317] mali-utgard 20001000.gpu: freq: 400000000, min_threshold: 73, max_threshold: 100 [ 7.486410] mali-utgard 20001000.gpu: initial freq = 200000000 [ 7.489299] Mali: Mali device driver loaded [ 7.489965] usbcore: registered new interface driver snd-usb-audio [ 7.489983] ALSA device list: [ 7.489996] #0: RK_RK322x [ 7.490008] #1: RK-HDMI-I2S [ 7.490020] #2: RK-SPDIF-CARD [ 7.490655] Freeing unused kernel memory: 384K (c0def000 - c0e4f000) [ 7.493475] init: init first stage started! [ 7.605007] mmc_host mmc2: Bus speed (slot 0) = 37500000Hz (slot req 400000Hz, actual 398936HZ div = 47) [ 7.605071] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out 800000Hz for init[mmc2] [ 7.631091] dwmmc_rockchip 30010000.rksdmmc: exceeding card's volts [ 7.631529] mmc2 not switch iovel. [ 7.657334] mmc_host mmc2: Bus speed (slot 0) = 37500000Hz (slot req 37500000Hz, actual 37500000HZ div = 0) [ 7.657428] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out normal clock [mmc2] [ 7.657449] type=1403 audit(4.780:2): policy loaded auid=4294967295 ses=4294967295 [ 7.657786] rk_sdmmc: BOOT Bus speed=37500000Hz,Bus width=4bits.[mmc2] [ 7.659237] mmc2: new high speed SDIO card at address 0001 [ 7.659396] init: (Initializing SELinux non-enforcing took 0.17s.) [ 7.671484] init: init second stage started! [ 7.686232] init: Setting ro.rk.soc=rk3229 [ 7.686838] init: property_set("ro.hardware", "rk30board") failed [ 7.695332] init: Running restorecon... [ 7.770816] init: waitpid failed: No child processes [ 7.771627] init: (Loading properties from /default.prop took 0.00s.) [ 7.776666] init: (Parsing /init.environ.rc took 0.00s.) [ 7.777955] init: (Parsing /init.usb.rc took 0.00s.) [ 7.780667] init: (Parsing init.rk30board.bootmode.unknown.rc took 0.00s.) [ 7.783965] init: (Parsing init.rk30board.usb.rc took 0.00s.) [ 7.784196] init: (Parsing init.rk30board.environment.rc took 0.00s.) [ 7.784281] init: could not import file '/init.debug.rc' from 'init.rockchip.rc': No such file or directory [ 7.784321] init: (Parsing init.rockchip.rc took 0.00s.) [ 7.785579] init: (Parsing init.connectivity.rc took 0.00s.) [ 7.785870] init: (Parsing init.box.samba.rc took 0.00s.) [ 7.785960] init: could not import file 'init.rk322x.rc' from '/init.rk30board.rc': No such file or directory [ 7.786245] init: (Parsing init.box.rc took 0.00s.) [ 7.786309] init: could not import file 'init.car.rc' from '/init.rk30board.rc': No such file or directory [ 7.786361] init: could not import file 'init.optee.rc' from '/init.rk30board.rc': No such file or directory [ 7.786404] init: (Parsing /init.rk30board.rc took 0.01s.) [ 7.788418] init: (Parsing /init.usb.configfs.rc took 0.00s.) [ 7.788672] init: (Parsing /init.zygote32.rc took 0.00s.) [ 7.788712] init: (Parsing /init.rc took 0.02s.) [ 7.789727] init: Starting service 'ueventd'... [ 7.792967] type=1400 audit(4.920:3): avc: denied { getattr } for pid=1 comm="init" path="/sys/kernel/debug/tracing/trace_marker" dev="debugfs" ino=73 scontext=u:r:init:s0 tcontext=u:object_r:debugfs_trace_marker:s0 tclass=file permissive=1 [ 7.794212] ueventd: ueventd started! [ 7.795338] ueventd: invalid gid 'trace' [ 7.890407] vendor storage:20160801 ret = -1 [ 8.052986] ueventd: Coldboot took 0.26s. [ 8.262783] init: Waiting for /dev/.coldboot_done... [ 8.262943] init: Waiting for /dev/.coldboot_done took 0.00s. [ 8.263051] init: /dev/hw_random not found [ 8.263635] keychord: using input dev 110b0030.pwm for fevent [ 8.286147] init: write_file: Unable to open '/proc/sys/abi/swp': No such file or directory [ 8.286632] pm policy 0 -> 1 [ 8.287847] init: /dev/hw_random not found [ 8.288476] rk30xxnand_ko: version magic '3.10.0 SMP preempt mod_unload ARMv7 p2v8 ' should be '3.10.104 SMP preempt mod_unload ARMv7 p2v8 ' [ 8.288608] init: finit_module for "/rk30xxnand_ko.ko" failed: Exec format error[ 8.289804] fs_mgr: Warning: unknown flag resize [ 8.292031] EXT4-fs (rknand_system): Ignoring removed nomblk_io_submit option [ 8.305578] EXT4-fs (rknand_system): mounted filesystem with ordered data mode. Opts: errors=remount-ro,nomblk_io_submit [ 8.306014] fs_mgr: check_fs(): mount(/dev/block/rknand_system,/system,ext4)=0: Success [ 8.307725] fs_mgr: check_fs(): unmount(/system) succeeded [ 8.307874] fs_mgr: Not running /system/bin/e2fsck on /dev/block/rknand_system (executable not in system image) [ 8.322585] EXT4-fs (rknand_system): mounted filesystem with ordered data mode. Opts: noauto_da_alloc,discard [ 8.322865] fs_mgr: __mount(source=/dev/block/rknand_system,target=/system,type=ext4)=0 [ 8.323419] fs_mgr: check_fs(): mount(/dev/block/rknand_cache,/cache,ext4)=-1: No such file or directory [ 8.327268] fs_mgr: Running /system/bin/e2fsck on /dev/block/rknand_cache [ 8.394145] e2fsck: CANNOT LINK EXECUTABLE "/system/bin/e2fsck": "/system/lib/libext2fs.so" has bad ELF magic [ 8.394145] [ 8.394455] e2fsck: e2fsck terminated by signal 6 [ 8.394455] [ 8.403398] EXT4-fs (rknand_cache): warning: maximal mount count reached, running e2fsck is recommended [ 8.405041] EXT4-fs (rknand_cache): mounted filesystem with ordered data mode. Opts: noauto_da_alloc,discard [ 8.405432] fs_mgr: __mount(source=/dev/block/rknand_cache,target=/cache,type=ext4)=0 [ 8.407095] EXT4-fs (rknand_metadata): Ignoring removed nomblk_io_submit option [ 8.412263] EXT4-fs (rknand_metadata): warning: maximal mount count reached, running e2fsck is recommended [ 8.413839] EXT4-fs (rknand_metadata): mounted filesystem with ordered data mode. Opts: errors=remount-ro,nomblk_io_submit [ 8.414185] fs_mgr: check_fs(): mount(/dev/block/rknand_metadata,/metadata,ext4)=0: Success [ 8.415934] fs_mgr: check_fs(): unmount(/metadata) succeeded [ 8.416107] fs_mgr: Running /system/bin/e2fsck on /dev/block/rknand_metadata [ 8.427841] e2fsck: CANNOT LINK EXECUTABLE "/system/bin/e2fsck": "/system/lib/libext2fs.so" has bad ELF magic [ 8.427841] [ 8.428062] e2fsck: e2fsck terminated by signal 6 [ 8.428062] [ 8.437207] EXT4-fs (rknand_metadata): warning: maximal mount count reached, running e2fsck is recommended [ 8.438718] EXT4-fs (rknand_metadata): mounted filesystem with ordered data mode. Opts: noauto_da_alloc,discard [ 8.439046] fs_mgr: __mount(source=/dev/block/rknand_metadata,target=/metadata,type=ext4)=0 [ 8.441662] EXT4-fs (rknand_userdata): Ignoring removed nomblk_io_submit option [ 8.447127] EXT4-fs (rknand_userdata): warning: maximal mount count reached, running e2fsck is recommended [ 8.448932] EXT4-fs (rknand_userdata): mounted filesystem with ordered data mode. Opts: errors=remount-ro,nomblk_io_submit [ 8.449328] fs_mgr: check_fs(): mount(/dev/block/rknand_userdata,/data,ext4)=0: Success [ 8.451159] fs_mgr: check_fs(): unmount(/data) succeeded [ 8.451385] fs_mgr: Running /system/bin/e2fsck on /dev/block/rknand_userdata [ 8.462985] e2fsck: CANNOT LINK EXECUTABLE "/system/bin/e2fsck": "/system/lib/libext2fs.so" has bad ELF magic [ 8.462985] [ 8.463205] e2fsck: e2fsck terminated by signal 6 [ 8.463205] [ 8.472876] EXT4-fs (rknand_userdata): warning: maximal mount count reached, running e2fsck is recommended [ 8.474713] EXT4-fs (rknand_userdata): mounted filesystem with ordered data mode. Opts: noauto_da_alloc,discard [ 8.475082] fs_mgr: __mount(source=/dev/block/rknand_userdata,target=/data,type=ext4)=0 init: (Parsing /system/etc/init/atrace.rc took 0.00s.) [ 8.504713] init: (Parsing /system/etc/init/audioserver.rc took 0.00s.) [ 8.506387] init: (Parsing /system/etc/init/bootanim.rc took 0.00s.) [ 8.508518] init: (Parsing /system/etc/init/bootstat.rc took 0.00s.) [ 8.510216] init: (Parsing /system/etc/init/cameraserver.rc took 0.00s.) [ 8.511930] init: (Parsing /system/etc/init/debuggerd.rc took 0.00s.) [ 8.513560] init: (Parsing /system/etc/init/drmserver.rc took 0.00s.) [ 8.515845] init: (Parsing /system/etc/init/dumpstate.rc took 0.00s.) [ 8.517427] init: (Parsing /system/etc/init/gatekeeperd.rc took 0.00s.) [ 8.519159] init: (Parsing /system/etc/init/init-debug.rc took 0.00s.) [ 8.520815] init: (Parsing /system/etc/init/installd.rc took 0.00s.) [ 8.522488] init: (Parsing /system/etc/init/keystore.rc took 0.00s.) [ 8.524101] init: (Parsing /system/etc/init/lmkd.rc took 0.00s.) [ 8.526823] init: (Parsing /system/etc/init/logcatd.rc took 0.00s.) [ 8.528684] init: (Parsing /system/etc/init/logd.rc took 0.00s.) [ 8.530549] init: (Parsing /system/etc/init/mdnsd.rc took 0.00s.) [ 8.532226] init: (Parsing /system/etc/init/mediacodec.rc took 0.00s.) [ 8.533852] init: (Parsing /system/etc/init/mediadrmserver.rc took 0.00s.) [ 8.535450] init: (Parsing /system/etc/init/mediaextractor.rc took 0.00s.) [ 8.537208] init: (Parsing /system/etc/init/mediaserver.rc took 0.00s.) [ 8.538828] init: (Parsing /system/etc/init/mtpd.rc took 0.00s.) [ 8.540463] init: (Parsing /system/etc/init/netd.rc took 0.00s.) [ 8.542099] init: (Parsing /system/etc/init/perfprofd.rc took 0.00s.) [ 8.543687] init: (Parsing /system/etc/init/racoon.rc took 0.00s.) [ 8.545366] init: ignored duplicate definition of service 'ril-daemon'init: (Parsing /system/etc/init/rild.rc took 0.00s.) [ 8.547330] init: (Parsing /system/etc/init/servicemanager.rc took 0.00s.) [ 8.548936] init: (Parsing /system/etc/init/surfaceflinger.rc took 0.00s.) [ 8.550725] init: (Parsing /system/etc/init/uncrypt.rc took 0.00s.) [ 8.552440] init: (Parsing /system/etc/init/vdc.rc took 0.00s.) [ 8.554188] init: (Parsing /system/etc/init/vold.rc took 0.00s.) [ 8.561709] init: property_set("ro.board.platform", "rk322x") failed [ 8.563678] init: property_set("ro.opengles.version", "196609") failed [ 8.564615] init: property_set("ro.rk.screenoff_time", "2147483647") failed [ 8.566069] init: property_set("ro.rk.screenshot_enable", "true") failed [ 8.566863] init: (Loading properties from /system/build.prop took 0.01s.) [ 8.567188] init: (Loading properties from /vendor/build.prop took 0.00s.) [ 8.567343] init: (Loading properties from /factory/factory.prop took 0.00s.) [ 8.567864] fs_mgr: Warning: unknown flag resize [ 8.568394] init: /recovery not specified in fstab [ 8.568778] init: Starting service 'healthd'... [ 8.575896] init: Starting service 'displayd'... [ 8.578656] init: Starting service 'lmkd'... [ 8.580108] binder: 140:140 transaction failed 29189, size 0-0 [ 8.581361] init: Starting service 'servicemanager'... [ 8.585295] init: Starting service 'surfaceflinger'... [ 8.587473] init: Starting service 'vold'... [ 8.589129] type=1400 audit(5.730:4): avc: denied { getattr } for pid=141 comm="displayd" path="/vendor" dev="rootfs" ino=6633 scontext=u:r:displayd:s0 tcontext=u:object_r:rootfs:s0 tclass=lnk_file permissive=1 [ 8.946498] init: Service 'displayd' (pid 141) killed by signal 6 [ 8.946571] init: Service 'displayd' (pid 141) killing any children in process group [ 8.946681] type=1400 audit(6.090:5): avc: denied { unlink } for pid=1 comm="init" name="displayd" dev="tmpfs" ino=3257 scontext=u:r:init:s0 tcontext=u:object_r:socket_device:s0 tclass=sock_file permissive=1 [ 8.946962] init: Service 'lmkd' (pid 142) killed by signal 6 [ 8.946998] init: Service 'lmkd' (pid 142) killing any children in process group [ 8.947220] init: Service 'servicemanager' (pid 143) killed by signal 6 [ 8.947255] init: Service 'servicemanager' (pid 143) killing any children in process group [ 8.947299] init: Service 'healthd' is being killed... [ 8.948212] init: Starting service 'zygote'... [ 8.949656] init: Starting service 'audioserver'... [ 8.951428] init: Starting service 'media'... [ 8.952322] init: Service 'surfaceflinger' is being killed... [ 8.952476] init: do_restart: Service inputflinger not found [ 8.953519] init: Starting service 'drm'... [ 8.955309] init: Starting service 'cameraserver'... [ 8.956174] init: couldn't write 150 to /dev/cpuset/camera-daemon/tasks: No such file or directory [ 8.956406] init: Service 'healthd' (pid 140) killed by signal 9 [ 8.956448] init: Service 'healthd' (pid 140) killing any children in process group [ 8.956811] init: Service 'surfaceflinger' (pid 144) killed by signal 6 [ 8.956860] init: Service 'surfaceflinger' (pid 144) killing any children in process group [ 8.956963] init: Service 'zygote' is being killed... [ 8.957426] init: Service 'vold' (pid 145) killed by signal 6 [ 8.957470] init: Service 'vold' (pid 145) killing any children in process group [ 8.957799] init: Service 'zygote' (pid 146) killed by signal 9 [ 8.957842] init: Service 'zygote' (pid 146) killing any children in process group [ 8.958061] init: write_file: Unable to open '/sys/android_power/request_state': No such file or directory [ 8.958191] init: write_file: Unable to write to '/sys/power/state': Invalid argument [ 8.958265] init: Service 'audioserver' is being killed... [ 8.958399] init: Service 'cameraserver' is being killed... [ 8.958630] init: Service 'media' is being killed... [ 8.959742] init: Starting service 'netd'... [ 8.960675] init: Service 'audioserver' (pid 147) killed by signal 9 [ 8.960722] init: Service 'audioserver' (pid 147) killing any children in process group [ 8.960948] init: Service 'media' (pid 148) killed by signal 9 [ 8.960995] init: Service 'media' (pid 148) killing any children in process group [ 8.961196] init: Service 'cameraserver' (pid 150) killed by signal 9 [ 8.961243] init: Service 'cameraserver' (pid 150) killing any children in process group [ 8.969968] init: insmod: open("/system/lib/modules/ump.ko") failed: No such file or directoryinit: insmod: open("/system/lib/modules/mali.ko") failed: No such file or directoryinit: insmod: open("/system/lib/modules/mali_kbase.ko") failed: No such file or directoryinit: insmod: open("/system/lib/modules/rk30_mirroring.ko") failed: No such file or directory [ 8.972131] rk29_ipp: version magic '3.0.101+ SMP preempt mod_unload ARMv7 ' should be '3.10.104 SMP preempt mod_unload ARMv7 p2v8 ' [ 8.972199] init: finit_module for "/system/lib/modules/rk29-ipp.ko" failed: Exec format errorinit: insmod: open("/system/lib/modules/pvrsrvkm.ko") failed: No such file or directory [ 8.972884] drmboot: module license 'unspecified' taints kernel. [ 8.972901] Disabling lock debugging due to kernel taint [ 8.973377] drm init, 20140910 [ 8.973433] ------------[ cut here ]------------ [ 8.973456] WARNING: at fs/sysfs/dir.c:530 sysfs_add_one+0x7c/0x9c() [ 8.973468] sysfs: cannot create duplicate filename '/devices/virtual/misc/rknand_sys_storage' [ 8.973480] Modules linked in: drmboot(P+) [ 8.973501] CPU: 1 PID: 1 Comm: init Tainted: P 3.10.104 #1 [ 8.973533] [<c0014088>] (unwind_backtrace+0x0/0xe0) from [<c00118cc>] (show_stack+0x10/0x14) [ 8.973559] [<c00118cc>] (show_stack+0x10/0x14) from [<c003f320>] (warn_slowpath_common+0x4c/0x68) [ 8.973580] [<c003f320>] (warn_slowpath_common+0x4c/0x68) from [<c003f3bc>] (warn_slowpath_fmt+0x2c/0x3c) [ 8.973601] [<c003f3bc>] (warn_slowpath_fmt+0x2c/0x3c) from [<c016d22c>] (sysfs_add_one+0x7c/0x9c) [ 8.973626] [<c016d22c>] (sysfs_add_one+0x7c/0x9c) from [<c016d434>] (create_dir+0x5c/0xac) [ 8.973652] [<c016d434>] (create_dir+0x5c/0xac) from [<c016d724>] (sysfs_create_dir+0x80/0xa0) [ 8.973677] [<c016d724>] (sysfs_create_dir+0x80/0xa0) from [<c02a6128>] (kobject_add_internal+0xc8/0x1fc) [ 8.973698] [<c02a6128>] (kobject_add_internal+0xc8/0x1fc) from [<c02a6488>] (kobject_add+0x68/0x8c) [ 8.973722] [<c02a6488>] (kobject_add+0x68/0x8c) from [<c038c374>] (device_add+0xe0/0x364) [ 8.973742] [<c038c374>] (device_add+0xe0/0x364) from [<c038c688>] (device_create_vargs+0x78/0xbc) [ 8.973761] [<c038c688>] (device_create_vargs+0x78/0xbc) from [<c038c6e8>] (device_create+0x1c/0x24) [ 8.973788] [<c038c6e8>] (device_create+0x1c/0x24) from [<c034ac88>] (misc_register.part.0+0x34/0xa0) [ 8.973817] [<c034ac88>] (misc_register.part.0+0x34/0xa0) from [<bf0030ac>] (StorageSysDataInit+0xac/0xdc [drmboot]) [ 8.973844] [<bf0030ac>] (StorageSysDataInit+0xac/0xdc [drmboot]) from [<c00086a4>] (do_one_initcall+0x34/0xc8) [ 8.973867] [<c00086a4>] (do_one_initcall+0x34/0xc8) from [<c09b2b70>] (do_init_module+0x44/0x15c) [ 8.973890] [<c09b2b70>] (do_init_module+0x44/0x15c) from [<c0095728>] (SyS_finit_module+0x6c/0x94) [ 8.973913] [<c0095728>] (SyS_finit_module+0x6c/0x94) from [<c000db00>] (ret_fast_syscall+0x0/0x38) [ 8.973927] ---[ end trace eda3561df640db71 ]--- [ 8.973961] ------------[ cut here ]------------ [ 8.973995] WARNING: at lib/kobject.c:196 kobject_add_internal+0x19c/0x1fc() [ 8.974008] kobject_add_internal failed for rknand_sys_storage with -EEXIST, don't try to register things with the same name in the same directory. [ 8.974020] Modules linked in: drmboot(P+) [ 8.974042] CPU: 1 PID: 1 Comm: init Tainted: P W 3.10.104 #1 [ 8.974067] [<c0014088>] (unwind_backtrace+0x0/0xe0) from [<c00118cc>] (show_stack+0x10/0x14) [ 8.974089] [<c00118cc>] (show_stack+0x10/0x14) from [<c003f320>] (warn_slowpath_common+0x4c/0x68) [ 8.974110] [<c003f320>] (warn_slowpath_common+0x4c/0x68) from [<c003f3bc>] (warn_slowpath_fmt+0x2c/0x3c) [ 8.974130] [<c003f3bc>] (warn_slowpath_fmt+0x2c/0x3c) from [<c02a61fc>] (kobject_add_internal+0x19c/0x1fc) [ 8.974151] [<c02a61fc>] (kobject_add_internal+0x19c/0x1fc) from [<c02a6488>] (kobject_add+0x68/0x8c) [ 8.974173] [<c02a6488>] (kobject_add+0x68/0x8c) from [<c038c374>] (device_add+0xe0/0x364) [ 8.974192] [<c038c374>] (device_add+0xe0/0x364) from [<c038c688>] (device_create_vargs+0x78/0xbc) [ 8.974212] [<c038c688>] (device_create_vargs+0x78/0xbc) from [<c038c6e8>] (device_create+0x1c/0x24) [ 8.974236] [<c038c6e8>] (device_create+0x1c/0x24) from [<c034ac88>] (misc_register.part.0+0x34/0xa0) [ 8.974264] [<c034ac88>] (misc_register.part.0+0x34/0xa0) from [<bf0030ac>] (StorageSysDataInit+0xac/0xdc [drmboot]) [ 8.974292] [<bf0030ac>] (StorageSysDataInit+0xac/0xdc [drmboot]) from [<c00086a4>] (do_one_initcall+0x34/0xc8) [ 8.974312] [<c00086a4>] (do_one_initcall+0x34/0xc8) from [<c09b2b70>] (do_init_module+0x44/0x15c) [ 8.974335] [<c09b2b70>] (do_init_module+0x44/0x15c) from [<c0095728>] (SyS_finit_module+0x6c/0x94) [ 8.974361] [<c0095728>] (SyS_finit_module+0x6c/0x94) from [<c000db00>] (ret_fast_syscall+0x0/0x38) [ 8.974389] ---[ end trace eda3561df640db72 ]--- [ 8.974412] drm init ok [ 8.974780] fs_mgr: Warning: unknown flag resize [ 8.975674] zram: Cannot initialise lz4 compressing backend [ 9.005272] Unable to find swap-space signature [ 9.005393] fs_mgr: swapon failed for /dev/block/zram0 [ 9.005717] init: Service 'drm' (pid 149) killed by signal 6 [ 9.005754] init: Service 'drm' (pid 149) killing any children in process group [ 9.006001] init: Service 'netd' (pid 151) killed by signal 6 [ 9.006037] init: Service 'netd' (pid 151) killing any children in process group [ 9.023561] vcodec_service: No noc aclk reset resource define [ 9.023614] vcodec_service: No noc hclk reset resource define [ 9.023625] vcodec_service: No core reset resource define [ 9.023635] vcodec_service: No cabac reset resource define [ 9.023788] vcodec 20020000.vpu_service: do not have pd_video [ 9.023837] vcodec_service: probe device 20020000.vpu_service [ 9.023911] vcodec_service: checking hw id 0 [ 9.025338] vcodec_service: init success [ 9.025556] vcodec_service: No noc aclk reset resource define [ 9.025573] vcodec_service: No noc hclk reset resource define [ 9.025582] vcodec_service: No core reset resource define [ 9.025591] vcodec_service: No cabac reset resource define [ 9.025744] vcodec 20030000.rkvdec: do not have pd_video [ 9.025788] vcodec_service: probe device 20030000.rkvdec [ 9.025880] vcodec_service: checking hw id 6876 [ 9.027092] vcodec_service: init success [ 9.031531] init: Starting service 'debuggerd'... [ 9.032484] init: do_start: Service debuggerd64 not found [ 9.033141] init: Starting service 'vold'... [ 9.038045] init: Not bootcharting. [ 9.048260] init: Service 'vold' (pid 157) killed by signal 6 [ 9.048322] init: Service 'vold' (pid 157) killing any children in process group [ 9.175890] init: Service 'debuggerd' (pid 156) killed by signal 6 [ 9.175998] init: Service 'debuggerd' (pid 156) killing any children in process group [ 9.262470] init: Starting service 'exec 1 (/system/bin/tzdatacheck)'... [ 9.279115] init: Service 'exec 1 (/system/bin/tzdatacheck)' (pid 159) killed by signal 6 [ 9.295724] type=1400 audit(6.440:6): avc: denied { setattr } for pid=1 comm="init" name="cifsmanager" dev="rknand_userdata" ino=239522 scontext=u:r:init:s0 tcontext=u:object_r:cifsmanager_exec:s0 tclass=dir permissive=1 [ 9.396545] EXT4-fs (rknand_userdata): Unrecognized mount option "background_gc=on" or missing value [ 9.402639] init: (Loading properties from /data/local.prop took 0.00s.) [ 9.644518] init: Starting service 'logd'... [ 9.646943] init: Starting service 'logd-reinit'... [ 9.669774] init: Service 'logd' (pid 160) killed by signal 6 [ 9.669882] init: Service 'logd' (pid 160) killing any children in process group [ 9.673540] init: Service 'logd-reinit' (pid 161) killed by signal 6 [ 9.674081] init: write_file: Unable to open '/proc/sys/vm/lazy_vfree_tlb_flush_all_threshold': No such file or directory [ 9.678857] init: SELinux: Could not get canonical path for /dev/block/platform/fe330000.sdhci/by-name/ restorecon: No such file or directory. [ 9.680137] init: property 'ro.serialno' doesn't exist while expanding '${ro.serialno}' [ 9.680205] init: write: cannot expand '${ro.serialno}' [ 9.681000] init: using deprecated syntax for specifying property 'ro.product.usbfactory', use ${name} instead [ 9.694299] init: write_file: Unable to write to '/dev/cpuset/foreground/boost/cpus': Permission denied [ 9.696315] init: Starting service 'console'... [ 9.697535] android_usb: already disabled [ 9.698344] init: Starting service 'adbd'... [ 9.699583] init: Service 'adbd' is being killed... [ 9.701320] init: cannot find '/system/bin/update_verifier' (No such file or directory), disabling 'exec 2 (/system/bin/update_verifier)' [ 9.701542] init: cannot find '/system/bin/install-recovery.sh' (No such file or directory), disabling 'flash_recovery' [ 9.702291] init: Starting service 'drmservice'... [ 9.703160] init: cannot find '/system/bin/bplus_helper' (No such file or directory), disabling 'bplus_helper' [ 9.704094] init: Service up_eth0 does not have a SELinux domain defined. [ 9.704198] init: cannot find '/system/bin/rk_store_keybox' (No such file or directory), disabling 'rk_store_keybox' [ 9.704347] init: cannot find '/system/bin/akmd' (No such file or directory), disabling 'akmd' [ 9.704863] init: Starting service 'zygote'... [ 9.706423] init: Starting service 'audioserver'... [ 9.708034] init: Starting service 'cameraserver'... [ 9.708940] init: couldn't write 167 to /dev/cpuset/camera-daemon/tasks: No such file or directory [ 9.709692] init: Starting service 'drm'... [ 9.715856] init: Starting service 'installd'... [ 9.718044] init: Starting service 'keystore'... [ 9.719946] init: Starting service 'mediacodec'... [ 9.722402] init: Starting service 'mediadrm'... [ 9.724073] init: Starting service 'mediaextractor'... [ 9.725599] init: Starting service 'media'... [ 9.727072] init: Starting service 'netd'... [ 9.728590] init: Service 'drm' (pid 168) killed by signal 6 [ 9.728689] init: Service 'drm' (pid 168) killing any children in process group [ 9.729828] init: Starting service 'gatekeeperd'... [ 9.830292] init: cannot find '/system/xbin/perfprofd' (No such file or directory), disabling 'perfprofd' [ 9.830685] init: Service 'drmservice' (pid 164) killed by signal 6 [ 9.831009] init: Service 'zygote' (pid 165) killed by signal 6 [ 9.831073] init: Service 'zygote' (pid 165) killing any children in process group [ 9.831327] init: write_file: Unable to open '/sys/android_power/request_state': No such file or directory [ 9.831524] init: write_file: Unable to write to '/sys/power/state': Invalid argument [ 9.831638] init: Service 'audioserver' is being killed... [ 9.831816] init: Service 'cameraserver' is being killed... [ 9.831973] init: Service 'media' is being killed... [ 9.832131] init: Service 'netd' is being killed... [ 9.832472] init: Service 'audioserver' (pid 166) killed by signal 6 [ 9.832537] init: Service 'audioserver' (pid 166) killing any children in process group [ 9.832768] init: Service 'cameraserver' (pid 167) killed by signal 6 [ 9.832832] init: Service 'cameraserver' (pid 167) killing any children in process group [ 9.833175] init: Service 'installd' (pid 169) killed by signal 6 [ 9.833241] init: Service 'installd' (pid 169) killing any children in process group [ 9.833606] init: Service 'keystore' (pid 170) killed by signal 6 [ 9.833670] init: Service 'keystore' (pid 170) killing any children in process group [ 9.833937] init: Service 'mediacodec' (pid 171) killed by signal 6 [ 9.834000] init: Service 'mediacodec' (pid 171) killing any children in process group [ 9.834273] init: Service 'mediadrm' (pid 172) killed by signal 6 [ 9.834339] init: Service 'mediadrm' (pid 172) killing any children in process group st 9.834618] init: Service 'mediaextractor' (pCid 1NN3) kT lLlIN byEXsEigCnUalTA BL6E "/sy em/b[ i 9.8n/s3h": 46/s4y] siteit/: Service 'imbedliiabmxtrsao"tohra's ( pidb173) EiLll mnggiac ny children in process group [ 9.834927] init: Service 'media' (pid 174) killed by signal 6 [ 9.834988] init: Service 'media' (pid 174) killing any children in process group [ 9.835285] init: Service 'netd' (pid 175) killed by signal 6 [ 9.835350] init: Service 'netd' (pid 175) killing any children in process group [ 9.836015] init: Service 'gatekeeperd' (pid 177) killed by signal 6 [ 9.836140] init: Service 'gatekeeperd' (pid 177) killing any children in process group [ 9.854842] init: Service 'console' (pid 162) killed by signal 6 [ 9.854946] init: Service 'console' (pid 162) killing any children in process group [ 12.810876] init: Starting service 'healthd'... [ 12.813766] init: Starting service 'displayd'... [ 12.816599] init: Starting service 'lmkd'... [ 12.819659] init: Starting service 'servicemanager'... [ 12.822451] binder: 178:178 transaction failed 29189, size 0-0 [ 12.822926] init: Starting service 'surfaceflinger'... [ 12.828032] type=1400 audit(10.030:7): avc: denied { getattr } for pid=179 comm="displayd" path="/vendor" dev="rootfs" ino=6633 scontext=u:r:displayd:s0 tcontext=u:object_r:rootfs:s0 tclass=lnk_file permissive=1 [ 12.833594] init: Service 'displayd' (pid 179) killed by signal 6 [ 12.833717] init: Service 'displayd' (pid 179) killing any children in process group [ 12.833910] type=1400 audit(10.040:8): avc: denied { unlink } for pid=1 comm="init" name="displayd" dev="tmpfs" ino=1467 scontext=u:r:init:s0 tcontext=u:object_r:socket_device:s0 tclass=sock_file permissive=1 [ 12.834460] init: Service 'servicemanager' (pid 181) killed by signal 6 [ 12.834531] init: Service 'servicemanager' (pid 181) killing any children in process group [ 12.834624] init: Service 'healthd' is being killed... [ 12.834885] init: Service 'surfaceflinger' is being killed... [ 12.835081] init: do_restart: Service inputflinger not found [ 12.835483] init: Service 'healthd' (pid 178) killed by signal 9 [ 12.835554] init: Service 'healthd' (pid 178) killing any children in process group [ 12.835830] init: Service 'lmkd' (pid 180) killed by signal 6 [ 12.835894] init: Service 'lmkd' (pid 180) killing any children in process group [ 12.839725] init: Service 'surfaceflinger' (pid 182) killed by signal 9 [ 12.839800] init: Service 'surfaceflinger' (pid 182) killing any children in process group [ 13.825840] init: Starting service 'console'... [ 13.828762] init: Starting service 'zygote'... [ 13.831563] init: Starting service 'audioserver'... [ 13.835635] init: Starting service 'cameraserver'... [ 13.837346] init: couldn't write 186 to /dev/cpuset/camera-daemon/tasks: No such file or directory [ 13.838834] init: Starting service 'debuggerd'... CANNOT LINK EXECUTABLE "/system/bin/sh": "/system/lib/libm.so" has bad ELF magic [ 13.842002] init: Starting service 'drm'... [ 13.846017] init: Starting service 'gatekeeperd'... [ 13.848300] init: Starting service 'installd'... [ 13.850699] init: Starting service 'keystore'... [ 13.853074] init: Starting service 'logd'... [ 13.864769] init: Starting service 'mediacodec'... [ 13.867229] init: Starting service 'mediadrm'... [ 13.869539] init: Starting service 'mediaextractor'... [ 13.871768] init: Starting service 'media'... [ 13.874881] init: Starting service 'netd'... [ 13.877679] init: Starting service 'vold'... [ 13.879652] init: Service 'console' (pid 183) killed by signal 6 [ 13.880400] init: Service 'console' (pid 183) killing any children in process group [ 13.881653] init: Service 'zygote' (pid 184) killed by signal 6 [ 13.882332] init: Service 'zygote' (pid 184) killing any children in process group [ 13.883510] init: write_file: Unable to open '/sys/android_power/request_state': No such file or directory [ 13.883714] init: write_file: Unable to write to '/sys/power/state': Invalid argument [ 13.883841] init: Service 'audioserver' is being killed... [ 13.884007] init: Service 'cameraserver' is being killed... [ 13.884168] init: Service 'media' is being killed... [ 13.884292] init: Service 'netd' is being killed... [ 13.884603] init: Service 'audioserver' (pid 185) killed by signal 6 [ 13.884644] init: Service 'audioserver' (pid 185) killing any children in process group [ 13.884895] init: Service 'cameraserver' (pid 186) killed by signal 6 [ 13.884940] init: Service 'cameraserver' (pid 186) killing any children in process group [ 13.885143] init: Service 'debuggerd' (pid 187) killed by signal 6 [ 13.885186] init: Service 'debuggerd' (pid 187) killing any children in process group [ 13.885416] init: Service 'drm' (pid 189) killed by signal 6 [ 13.885468] init: Service 'drm' (pid 189) killing any children in process group [ 13.885683] init: Service 'gatekeeperd' (pid 190) killed by signal 6 [ 13.885729] init: Service 'gatekeeperd' (pid 190) killing any children in process group [ 13.886062] init: Service 'installd' (pid 191) killed by signal 6 [ 13.886110] init: Service 'installd' (pid 191) killing any children in process group [ 13.886462] init: Service 'keystore' (pid 192) killed by signal 6 [ 13.886510] init: Service 'keystore' (pid 192) killing any children in process group [ 13.886777] init: Service 'mediacodec' (pid 195) killed by signal 6 [ 13.886835] init: Service 'mediacodec' (pid 195) killing any children in process group [ 13.887143] init: Service 'mediadrm' (pid 196) killed by signal 6 [ 13.887204] init: Service 'mediadrm' (pid 196) killing any children in process group [ 13.887478] init: Service 'mediaextractor' (pid 197) killed by signal 6 [ 13.887527] init: Service 'mediaextractor' (pid 197) killing any children in process group [ 13.887828] init: Service 'media' (pid 198) killed by signal 6 [ 13.887883] init: Service 'media' (pid 198) killing any children in process group [ 13.898708] init: Service 'logd' (pid 194) killed by signal 6 [ 13.898758] init: Service 'logd' (pid 194) killing any children in process group [ 13.899168] init: Service 'netd' (pid 199) killed by signal 6 [ 13.899209] init: Service 'netd' (pid 199) killing any children in process group [ 13.899537] init: Service 'vold' (pid 200) killed by signal 6 [ 13.899578] init: Service 'vold' (pid 200) killing any children in process group [ 13.912435] [otg id chg] last id -1 current id 2 [ 17.840901] init: Starting service 'healthd'... [ 17.843765] init: Starting service 'displayd'... [ 17.846537] init: Starting service 'lmkd'... [ 17.849758] init: Starting service 'servicemanager'... [ 17.851735] binder: 201:201 transaction failed 29189, size 0-0 [ 17.852898] init: Starting service 'surfaceflinger'... [ 17.859140] type=1400 audit(15.150:9): avc: denied { getattr } for pid=202 comm="displayd" path="/vendor" dev="rootfs" ino=6633 scontext=u:r:displayd:s0 tcontext=u:object_r:rootfs:s0 tclass=lnk_file permissive=1 [ 17.862059] init: Service 'displayd' (pid 202) killed by signal 6 [ 17.862862] init: Service 'displayd' (pid 202) killing any children in process group [ 17.863507] init: Service 'lmkd' (pid 203) killed by signal 6 [ 17.863595] init: Service 'lmkd' (pid 203) killing any children in process group [ 17.865576] init: Service 'surfaceflinger' (pid 205) killed by signal 6 [ 17.865677] init: Service 'surfaceflinger' (pid 205) killing any children in process group [ 17.869335] init: Service 'servicemanager' (pid 204) killed by signal 6 [ 17.869432] init: Service 'servicemanager' (pid 204) killing any children in process group [ 17.869509] init: Service 'healthd' is being killed... [ 17.869768] init: do_restart: Service inputflinger not found [ 17.871271] init: Service 'healthd' (pid 201) killed by signal 9 [ 17.871343] init: Service 'healthd' (pid 201) killing any children in process group [ 18.857356] init: Starting service 'console'... [ 18.860182] init: Starting service 'zygote'... [ 18.863241] init: Starting service 'audioserver'... [ 18.866292] init: Starting service 'cameraserver'... [ 18.869334] init: Starting service 'debuggerd'... [ 18.872558] init: couldn't write 209 to /dev/cpuset/camera-daemon/tasks: No such file or directory [ 18.873845] init: Starting service 'drm'... [ 18.876222] init: Starting service 'gatekeeperd'... [ 18.878802] init: Starting service 'installd'... [ 18.881093] init: Starting service 'keystore'... CANNOT LINK EXECUTABLE "/system/bin/sh": "/system/lib/libm.so" has bad ELF magic [ 18.884514] init: Starting service 'logd'... [ 18.887493] init: Starting service 'mediacodec'... [ 18.890676] init: Starting service 'mediadrm'... [ 18.893577] init: Starting service 'mediaextractor'... [ 18.896411] init: Starting service 'media'... [ 18.899390] init: Starting service 'netd'... [ 18.903487] init: Starting service 'vold'... [ 18.907014] init: Service 'console' (pid 206) killed by signal 6 [ 18.907793] init: Service 'console' (pid 206) killing any children in process group [ 18.909169] init: Service 'zygote' (pid 207) killed by signal 6 [ 18.909900] init: Service 'zygote' (pid 207) killing any children in process group [ 18.911090] init: write_file: Unable to open '/sys/android_power/request_state': No such file or directory [ 18.912410] init: write_file: Unable to write to '/sys/power/state': Invalid argument [ 18.913366] init: Service 'audioserver' is being killed... [ 18.914168] init: Service 'cameraserver' is being killed... [ 18.915084] init: Service 'media' is being killed... [ 18.915846] init: Service 'netd' is being killed... [ 18.916813] init: Service 'audioserver' (pid 208) killed by signal 6 [ 18.917542] init: Service 'audioserver' (pid 208) killing any children in process group [ 18.917858] init: Service 'cameraserver' (pid 209) killed by signal 6 [ 18.917920] init: Service 'cameraserver' (pid 209) killing any children in process group [ 18.918227] init: Service 'debuggerd' (pid 210) killed by signal 6 [ 18.918284] init: Service 'debuggerd' (pid 210) killing any children in process group [ 18.918539] init: Service 'drm' (pid 211) killed by signal 6 [ 18.918595] init: Service 'drm' (pid 211) killing any children in process group [ 18.918862] init: Service 'gatekeeperd' (pid 212) killed by signal 6 [ 18.918920] init: Service 'gatekeeperd' (pid 212) killing any children in process group [ 18.919268] init: Service 'installd' (pid 213) killed by signal 6 [ 18.919337] init: Service 'installd' (pid 213) killing any children in process group [ 18.919745] init: Service 'keystore' (pid 214) killed by signal 6 [ 18.919820] init: Service 'keystore' (pid 214) killing any children in process group [ 18.920115] init: Service 'mediacodec' (pid 216) killed by signal 6 [ 18.920178] init: Service 'mediacodec' (pid 216) killing any children in process group [ 18.920559] init: Service 'mediadrm' (pid 217) killed by signal 6 [ 18.920618] init: Service 'mediadrm' (pid 217) killing any children in process group [ 18.920880] init: Service 'mediaextractor' (pid 218) killed by signal 6 [ 18.930998] init: Service 'mediaextractor' (pid 218) killing any children in process group [ 18.931395] init: Service 'logd' (pid 215) killed by signal 6 [ 18.931452] init: Service 'logd' (pid 215) killing any children in process group [ 18.931827] init: Service 'media' (pid 219) killed by signal 9 [ 18.931873] init: Service 'media' (pid 219) killing any children in process group [ 18.932107] init: Service 'netd' (pid 220) killed by signal 6 [ 18.932158] init: Service 'netd' (pid 220) killing any children in process group [ 18.932538] init: Service 'vold' (pid 222) killed by signal 6 [ 18.932585] init: Service 'vold' (pid 222) killing any children in process group [ 19.752331] read descriptors [ 19.752448] read descriptors [ 19.752490] read strings [ 19.752602] pcd_pullup, is_on 1 [ 22.711727] init: Starting service 'healthd'... [ 22.714707] init: Starting service 'displayd'... [ 22.717422] init: Starting service 'lmkd'... [ 22.720746] init: Starting service 'servicemanager'... [ 22.723276] binder: 227:227 transaction failed 29189, size 0-0 [ 22.723824] init: Starting service 'surfaceflinger'... [ 22.731971] init: Service 'displayd' (pid 228) killed by signal 6 [ 22.732121] init: Service 'displayd' (pid 228) killing any children in process group [ 22.735856] init: Service 'lmkd' (pid 229) killed by signal 6 [ 22.735960] init: Service 'lmkd' (pid 229) killing any children in process group [ 22.736376] init: Service 'surfaceflinger' (pid 231) killed by signal 6 [ 22.736443] init: Service 'surfaceflinger' (pid 231) killing any children in process group [ 22.739652] init: Service 'servicemanager' (pid 230) killed by signal 6 [ 22.739752] init: Service 'servicemanager' (pid 230) killing any children in process group [ 22.739829] init: Service 'healthd' is being killed... [ 22.740084] init: do_restart: Service inputflinger not found [ 22.741612] init: Service 'healthd' (pid 227) killed by signal 9 [ 22.741683] init: Service 'healthd' (pid 227) killing any children in process group [ 23.727598] init: Starting service 'console'... [ 23.730423] init: Starting service 'zygote'... [ 23.733457] init: Starting service 'audioserver'... [ 23.736326] init: Starting service 'cameraserver'... [ 23.739503] init: Starting service 'debuggerd'... [ 23.743374] init: couldn't write 235 to /dev/cpuset/camera-daemon/tasks: No such file or directory [ 23.744271] init: Starting service 'drm'... [ 23.746546] init: Starting service 'gatekeeperd'... [ 23.748964] init: Starting service 'installd'... [ 23.751331] init: Starting service 'keystore'... CANNOT LINK EXECUTABLE "/system/bin/sh": "/system/lib/libm.so" has bad ELF magic [ 23.754413] init: Starting service 'logd'... [ 23.756413] init: Starting service 'mediacodec'... [ 23.758520] init: Starting service 'mediadrm'... [ 23.760737] init: Starting service 'mediaextractor'... [ 23.769639] init: Starting service 'media'... [ 23.772252] init: Starting service 'netd'... [ 23.774918] init: Starting service 'vold'... [ 23.776861] init: Service 'console' (pid 232) killed by signal 6 [ 23.778147] init: Service 'console' (pid 232) killing any children in process group [ 23.779372] init: Service 'zygote' (pid 233) killed by signal 6 [ 23.780041] init: Service 'zygote' (pid 233) killing any children in process group [ 23.781099] init: write_file: Unable to open '/sys/android_power/request_state': No such file or directory [ 23.781290] init: write_file: Unable to write to '/sys/power/state': Invalid argument [ 23.781427] init: Service 'audioserver' is being killed... [ 23.781606] init: Service 'cameraserver' is being killed... [ 23.781802] init: Service 'media' is being killed... [ 23.782105] init: Service 'netd' is being killed... [ 23.782501] init: Service 'audioserver' (pid 234) killed by signal 6 [ 23.782557] init: Service 'audioserver' (pid 234) killing any children in process group [ 23.782883] init: Service 'cameraserver' (pid 235) killed by signal 6 [ 23.782937] init: Service 'cameraserver' (pid 235) killing any children in process group [ 23.783166] init: Service 'debuggerd' (pid 236) killed by signal 6 [ 23.783207] init: Service 'debuggerd' (pid 236) killing any children in process group [ 23.783422] init: Service 'drm' (pid 237) killed by signal 6 [ 23.783464] init: Service 'drm' (pid 237) killing any children in process group [ 23.783738] init: Service 'gatekeeperd' (pid 238) killed by signal 6 [ 23.783794] init: Service 'gatekeeperd' (pid 238) killing any children in process group [ 23.784085] init: Service 'installd' (pid 239) killed by signal 6 [ 23.784136] init: Service 'installd' (pid 239) killing any children in process group [ 23.784430] init: Service 'keystore' (pid 240) killed by signal 6 [ 23.784485] init: Service 'keystore' (pid 240) killing any children in process group [ 23.784832] init: Service 'logd' (pid 241) killed by signal 6 [ 23.784892] init: Service 'logd' (pid 241) killing any children in process group [ 23.785360] init: Service 'mediacodec' (pid 242) killed by signal 6 [ 23.785401] init: Service 'mediacodec' (pid 242) killing any children in process group [ 23.785598] init: Service 'mediadrm' (pid 243) killed by signal 6 [ 23.785634] init: Service 'mediadrm' (pid 243) killing any children in process group [ 23.785831] init: Service 'mediaextractor' (pid 244) killed by signal 6 [ 23.785875] init: Service 'mediaextractor' (pid 244) killing any children in process group [ 23.786001] init: Service 'media' (pid 245) killed by signal 9 [ 23.786036] init: Service 'media' (pid 245) killing any children in process group [ 23.786235] init: Service 'netd' (pid 246) killed by signal 9 [ 23.786276] init: Service 'netd' (pid 246) killing any children in process group [ 23.795101] init: Service 'vold' (pid 247) killed by signal 6 [ 23.795146] init: Service 'vold' (pid 247) killing any children in process group [ 27.735817] init: Starting service 'healthd'... [ 27.738727] init: Starting service 'displayd'... [ 27.741485] init: Starting service 'lmkd'... [ 27.744461] init: Starting service 'servicemanager'... [ 27.746707] binder: 248:248 transaction failed 29189, size 0-0 [ 27.747703] init: Starting service 'surfaceflinger'... [ 27.753854] init: Service 'displayd' (pid 249) killed by signal 6 [ 27.753997] init: Service 'displayd' (pid 249) killing any children in process group [ 27.754174] type=1400 audit(25.200:10): avc: denied { unlink } for pid=1 comm="init" name="displayd" dev="tmpfs" ino=8446 scontext=u:r:init:s0 tcontext=u:object_r:socket_device:s0 tclass=sock_file permissive=1 [ 27.759046] init: Service 'surfaceflinger' (pid 252) killed by signal 6 [ 27.759190] init: Service 'surfaceflinger' (pid 252) killing any children in process group [ 27.761995] init: Service 'lmkd' (pid 250) killed by signal 6 [ 27.762070] init: Service 'lmkd' (pid 250) killing any children in process group [ 27.762260] init: critical process 'lmkd' exited 4 times in 4 minutes; rebooting into recovery mode [ 27.764022] SysRq : Emergency Remount R/O [ 27.767023] EXT4-fs (rknand_userdata): re-mounted. Opts: (null) [ 27.771844] EXT4-fs (rknand_metadata): re-mounted. Opts: (null) [ 27.778837] EXT4-fs (rknand_cache): re-mounted. Opts: (null) [ 27.779145] Emergency Remount complete [ 27.866989] cpufreq: cpufreq: reboot set core rate=1008000000, volt=1225000 [ 27.867483] dwc_otg_driver_shutdown: disconnect USB host mode [ 27.868458] PortPower off [ 27.868697] rk_battery_charger_detect_cb , battery_charger_detect 6 [ 27.870333] rknand_shutdown... [ 27.870638] nand th quited [ 27.947053] rknand_shutdown:OK [ 28.021388] Restarting system with command 'recovery'. DDR Version V1.06 20170902_dbg In 300MHz DDR3 Bus Width=16 Col=11 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB mach:2 OUT Boot1 Release Time: Nov 27 2017 10:11:34, version: 2.47 ChipType = 0xc, 361 No.1 FLASH ID:2c 64 44 32 a5 0 ECC:60 SdmmcInit=0 2 StorageInit ok = 329384 SecureMode = 0 Code check OK! theLoader 0x60000000, 356626 Code check OK! theLoader 0x68400000, 381565 Enter Trust OS INF TEE-CORE:init_primary_helper:319: Initializing (1.0.1-72-gf230aa2 #2 Fri Sep 29 10:22:10 UTC 2017 arm) INF TEE-CORE:init_primary_helper:320: Release version: 2.0 INF TEE-CORE:init_teecore:79: teecore inits done U-Boot 2014.10-RK322X-06-02489-g4e89f4b-dirty (Aug 06 2018 - 17:36:59) CPU: rk322x cpu version = 3 CPU's clock information: arm pll = 600000000HZ periph pll = 600000000HZ ddr pll = 600000000HZ codec pll = 500000000HZ Board: Rockchip platform Board Uboot as second level loader DRAM: Found dram banks: 1 Adding bank:0000000060000000(0000000040000000) Reserve memory for trust os. dram reserve bank: base = 0x68400000, size = 0x00100000 128 MiB GIC CPU mask = 0x00000001 rk dma pl330 version: 1.4 remotectl v0.1 pwm freq=0x11e1a3 pwm_freq_nstime=0x355 SdmmcInit = 0 20 SdmmcInit = 2 20 storage init OK! Using default environment GetParam Load FDT from resource image. can't find dts node for fixed No pmic detect. DRAM: dram freq:500MHz SecureBootEn = 0, SecureBootLock = 0 #Boot ver: 2018-08-06#2.37 empty serial no. reboot recover. no fuel gauge found no fuel gauge found can't find power_ctr node for lcdc0 HDMI: no pull up gpio can't find dts node for deviceinfo rk_hdmi_register:fail to read deviceinfo preset hdmi resolution is 1920x1080@60-1,i=10 left = 0, right = 0, top = 0, bottom = 0, overscan = 0 panel->left = 100 , panel->right = 100 ,panel->top = 100, panel->bottom = 100, panel->overscan = 100 preset tve resolution is 720x576@50-1,i=1 Hdmi Devices Not Exist. can't find dts node for rk312x-tve SCREEN_TVOUT rk3036_tve_init:use baseparamer config g_tve_pos = 1 read logo on state from dts [1] no fuel gauge found load fdt from resouce. ERROR: [get_entry_ram]: Cannot find logo_kernel.bmp! Secure Boot state: 0 kernel @ 0x62000000 (0x007c6ce8) ramdisk @ 0x65bf0000 (0x004c2b30) bootrk: do_bootm_linux... Loading Device Tree to 65600000, end 65614b77 ... OK Add bank:0000000060000000, 0000000008400000 Add bank:0000000068500000, 0000000037b00000 Starting kernel ... <hit enter to activate fiq debugger> [ 0.000000] Booting Linux on physical CPU 0xf00 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.10.104 (akrd-52@aike5) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #1 SMP PREEMPT Mon Aug 6 17:39:32 CST 2018 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Rockchip RK3229, model: rockchip,rk3229 [ 0.000000] rockchip_uboot_logo_setup: mem: 0x02000000@0x9dc00000, offset:0x00000000 [ 0.000000] hdmi init vic is 65541 [ 0.000000] cvbs init tve.format is 1 [ 0.000000] cvbs init tve.format is 1 [ 0.000000] cvbs init tve.format is 1 [ 0.000000] rockchip_uboot_mem_reserve: reserve 0x02000000@0x9dc00000 for uboot logo [ 0.000000] rockchip_ion_reserve [ 0.000000] ion heap(vmalloc): base(0) size(0) align(0) [ 0.000000] cma: CMA: reserved 16 MiB at 7f000000 [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] Boot mode: RECOVERY (2) flag: RECOVER (0xc3524203) [ 0.000000] psci: probing function IDs from device-tree [ 0.000000] PERCPU: Embedded 9 pages/cpu @c18ec000 s13440 r8192 d15232 u36864 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260864 [ 0.000000] Kernel command line: vmalloc=496M psci=enable rockchip_jtag console=ttyFIQ0 androidboot.selinux=permissive androidboot.hardware=rk30board androidboot.console=ttyFIQ0 init=/init mtdparts=rk29xxnand:0x00002000@0x00000000(parameter),0x00002000@0x00002000(uboot),0x00004000@0x00004000(trust),0x00002000@0x00008000(misc),0x00000800@0x0000A000(baseparamer),0x00007800@0x0000A800(resource),0x00006000@0x00012000(kernel),0x00006000@0x00018000(boot),0x00010000@0x0001E000(recovery),0x00020000@0x0002E000(backup),0x00040000@0x0004E000(cache),0x00008000@0x0008E000(metadata),0x00002000@0x00096000(kpanic),0x00600000@0x00098000(system),-@0x00698000(userdata) storagemedia=nand uboot_logo=0x02000000@0x9dc00000 loader.timestamp=2018-08-06_17:36:59 hdmi.vic=65541 tve.format=1 SecureBootCheckOk=0 [ 0.000000] rockchip jtag enabled [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] allocated 2097152 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 132MB 891MB = 1023MB total [ 0.000000] Memory: 965292k/965292k available, 82260k reserved, 491516K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0dee7d4 (14234 kB) [ 0.000000] .init : 0xc0def000 - 0xc0e4f480 ( 386 kB) [ 0.000000] .data : 0xc0e50000 - 0xc0f809e0 (1219 kB) [ 0.000000] .bss : 0xc0f809e0 - 0xc10b051c (1215 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] rk_clk_tree_init start! [ 0.000000] rk_get_uboot_display_flag: uboot_logo_on = 1 [ 0.000000] rkclk_init_clks: cnt_parent = 13 [ 0.000000] rkclk_init_clks: cnt_rate = 19 [ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] Switching to timer-based delay loop [ 0.000000] sched_clock: ARM arch timer >56 bits at 24000kHz, resolution 41ns [ 0.000000] process version: 0 [ 0.000000] channel:0, lkg:3 [ 0.000000] target-temp:95 [ 0.000000] channel:2, lkg:3 [ 0.000000] target-temp:0 [ 0.000000] channel:2, lkg:3 [ 0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms [ 3.134673] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 3.134699] pid_max: default: 32768 minimum: 301 [ 3.134935] Security Framework initialized [ 3.134966] SELinux: Initializing. [ 3.135098] Mount-cache hash table entries: 512 [ 3.136240] Initializing cgroup subsys debug [ 3.136267] Initializing cgroup subsys memory [ 3.136320] Initializing cgroup subsys freezer [ 3.136382] CPU: Testing write buffer coherency: ok [ 3.136892] /cpus/cpu@0 missing clock-frequency property [ 3.136917] /cpus/cpu@1 missing clock-frequency property [ 3.136937] /cpus/cpu@2 missing clock-frequency property [ 3.136957] /cpus/cpu@3 missing clock-frequency property [ 3.137055] CPU0: thread -1, cpu 0, socket 15, mpidr 80000f00 [ 3.137099] Setting up static identity map for 0xc09d1ea0 - 0xc09d1ef8 [ 3.139503] last_log: 0x7e900000 map to 0xe0804000 and copy to 0xe0886000, size 0x80000 early 0x17d6 (version 3.1) [ 3.212690] CPU1: Booted secondary processor [ 3.212747] CPU1: thread -1, cpu 1, socket 15, mpidr 80000f01 [ 3.232369] CPU2: Booted secondary processor [ 3.232412] CPU2: thread -1, cpu 2, socket 15, mpidr 80000f02 [ 3.252106] CPU3: Booted secondary processor [ 3.252150] CPU3: thread -1, cpu 3, socket 15, mpidr 80000f03 [ 3.252314] Brought up 4 CPUs [ 3.252365] SMP: Total of 4 processors activated (192.00 BogoMIPS). [ 3.252380] CPU: All CPU(s) started in SVC mode. [ 3.253791] devtmpfs: initialized [ 3.262322] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 3.263963] pinctrl core: initialized pinctrl subsystem [ 3.264450] regulator-dummy: no parameters [ 3.286545] NET: Registered protocol family 16 [ 3.290036] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 3.290875] ion_snapshot: 0x7ea60000 map to 0xe0907000 and copy to 0xc1085b34 (version 0.1) [ 3.291092] Registered FIQ tty driver [ 3.293332] console [ttyFIQ0] enabled [ 3.293745] Registered fiq debugger ttyFIQ0 [ 3.296302] syscon 10140000.syscon: regmap [mem 0x10140000-0x10140fff] registered [ 3.296625] syscon 11000000.syscon: regmap [mem 0x11000000-0x11000fff] registered [ 3.296946] syscon 110e0000.syscon: regmap [mem 0x110e0000-0x110e0fff] registered [ 3.297241] syscon 11200000.syscon: regmap [mem 0x11200000-0x112003ff] registered [ 3.297572] syscon 31020000.syscon: regmap [mem 0x31020000-0x31022fff] registered [ 3.304082] rk_iommu 20053f00.vop_mmu: (vop) Enter [ 3.304243] rk_iommu 20053f00.vop_mmu: IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000. [ 3.304272] rk_iommu 20053f00.vop_mmu: (vop) Initialized [ 3.304534] rk_iommu 20020800.vpu_mmu: (vpu) Enter [ 3.304657] rk_iommu 20020800.vpu_mmu: IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000. [ 3.304685] rk_iommu 20020800.vpu_mmu: (vpu) Initialized [ 3.304921] rk_iommu 20070800.iep_mmu: (iep) Enter [ 3.305051] rk_iommu 20070800.iep_mmu: IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000. [ 3.305077] rk_iommu 20070800.iep_mmu: (iep) Initialized [ 3.305327] rk_iommu 20030480.vdec_mmu: (vdec) Enter [ 3.305447] rk_iommu 20030480.vdec_mmu: IOVMM: Created 0x3ffff000 B IOVMM from 0x10000000. [ 3.305475] rk_iommu 20030480.vdec_mmu: (vdec) Initialized [ 3.315135] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 3.315167] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 3.315213] rockchip sip version v1 [ 3.315842] rk3368_init_rockchip_pmu_ops: could not find pmu dt node [ 3.386669] bio: create slab <bio-0> at 0 [ 3.387745] Rockchip hdmi driver version 2.0 [ 3.388293] vccio_1v8: 1800 mV [ 3.388645] vccio_3v3: 3300 mV [ 3.390726] SCSI subsystem initialized [ 3.391128] usbcore: registered new interface driver usbfs [ 3.391246] usbcore: registered new interface driver hub [ 3.391467] usbcore: registered new device driver usb [ 3.395777] rockchip_i2c 11050000.i2c: i2c-0: Rockchip I2C adapter [ 3.396014] media: Linux media interface: v0.10 [ 3.396105] Linux video capture interface: v2.00 [ 3.396354] pps_core: LinuxPPS API ver. 1 registered [ 3.396374] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 3.396421] PTP clock support registered [ 3.396519] i2c-core: driver [bq24296] using legacy suspend method [ 3.396541] i2c-core: driver [bq24296] using legacy resume method [ 3.398009] Rockchip ion module is successfully loaded (v1.1) [ 3.398384] Advanced Linux Sound Architecture Driver Initialized. [ 3.399203] Bluetooth: Core ver 2.16 [ 3.399293] NET: Registered protocol family 31 [ 3.399313] Bluetooth: HCI device and connection manager initialized [ 3.399346] Bluetooth: HCI socket layer initialized [ 3.399374] Bluetooth: L2CAP socket layer initialized [ 3.399452] Bluetooth: SCO socket layer initialized [ 3.399902] cfg80211: Calling CRDA to update world regulatory domain [ 3.402891] i2c-core: driver [rk816] using legacy suspend method [ 3.402919] i2c-core: driver [rk816] using legacy resume method [ 3.402984] i2c-core: driver [rk818] using legacy suspend method [ 3.403005] i2c-core: driver [rk818] using legacy resume method [ 3.404342] rockchip-i2s 100c0000.i2s0: i2s0 has no mclk [ 3.407270] Switching to clocksource arch_sys_counter [ 3.446246] rga: Module initialized. [ 3.447058] rga2 20060000.rga: rga ion client create success! [ 3.447375] rga: Driver loaded succesfully [ 3.447694] fb disp policy is box [ 3.447734] uboot-logo-on:1 [ 3.447795] rk-fb rockchip-fb: rk fb ion client create success! [ 3.447821] rk-fb rockchip-fb: rockchip framebuffer driver probe [ 3.448403] can't find screen_init node [ 3.448435] rk-screen rk_screen.15: rockchip screen probe success [ 3.450544] rk322x-lcdc 20050000.vop: vop_dev->regs=0xe0930000 [ 3.450663] rk322x-lcdc vop0: can't find power_ctr node for lcdc0 [ 3.451179] graphics fb0: rockchip framebuffer registerd:fb0 [ 3.451909] graphics fb1: rockchip framebuffer registerd:fb1 [ 3.452312] graphics fb2: rockchip framebuffer registerd:fb2 [ 3.453329] rk322x-lcdc vop0: lcdc0: dclk:297000000>>fps:450 [ 3.488666] alloc_buffer:ion_phy_addr=0x10000000 [ 3.505826] fb0:phy:10000000>>vir:e093a000>>len:0x1800000 [ 3.555813] rk_iommu 20053f00.vop_mmu: rockchip_iommu_attach_device: Attached new IOMMU with pgtable 0x7e995000 [ 3.555902] rk322x-lcdc vop0: lcdc0 probe ok, iommu enabled [ 3.559320] NET: Registered protocol family 2 [ 3.560587] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 3.560727] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 3.560830] TCP: Hash tables configured (established 4096 bind 4096) [ 3.560934] TCP: reno registered [ 3.560961] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 3.561004] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 3.561358] NET: Registered protocol family 1 [ 3.561901] RPC: Registered named UNIX socket transport module. [ 3.561928] RPC: Registered udp transport module. [ 3.561946] RPC: Registered tcp transport module. [ 3.561964] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 3.563249] Unpacking initramfs... [ 3.974301] Freeing initrd memory: 4872K (c5bf0000 - c60b2000) [ 3.976214] hw perfevents: enabled with ARMv7_Cortex_A7 PMU driver, 5 counters available [ 3.980757] audit: initializing netlink socket (disabled) [ 3.980863] type=2000 audit(0.850:1): initialized [ 3.982265] bounce pool size: 64 pages [ 3.991730] NFS: Registering the id_resolver key type [ 3.991854] Key type id_resolver registered [ 3.991876] Key type id_legacy registered [ 3.992661] fuse init (API version 7.22) [ 3.993440] msgmni has been set to 966 [ 3.994026] [ 3.994026] TEE Core Framework initialization (ver 1:0.1) [ 3.994102] TEE armv7 Driver initialization [ 3.994655] tz_tee_probe: name="armv7sec", id=0, pdev_name="armv7sec.0" [ 3.994687] TEE core: Alloc the misc device "opteearmtz00" (id=0) [ 3.995069] TEE Core: Register the misc device "opteearmtz00" (id=0,minor=58) [ 3.998127] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 3.998173] io scheduler noop registered [ 3.998195] io scheduler deadline registered [ 3.998411] io scheduler cfq registered (default) [ 4.001090] HDMI: no pull up gpio [ 4.001924] reset hdmi [ 4.002184] rockchip-hdmiv2 200a0000.hdmi: rockchip hdmiv2 probe success. [ 4.002947] iep: failed to find iep power down clock source. [ 4.003552] iep ion client create success! [ 4.003589] IEP Power ON [ 4.003998] rk_iommu 20070800.iep_mmu: rockchip_iommu_attach_device: Attached new IOMMU with pgtable 0x7ea53000 [ 4.004020] IEP Power OFF [ 4.004048] IEP Driver loaded succesfully [ 4.004215] Module initialized. [ 4.005211] rk3036-tve 20053e00.tve: Can not read det_io [ 4.005350] rk3036-tve 20053e00.tve: rockchip,rk322x-tve tv encoder probe ok [ 4.008735] dma-pl330 110f0000.pdma: Loaded driver for PL330 DMAC-2364208 [ 4.008788] dma-pl330 110f0000.pdma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16 [ 4.009390] vdd_arm: 950 <--> 1400 mV at 1100 mV [ 4.010013] vdd_logic: 1000 <--> 1300 mV at 1200 mV [ 4.010659] rk_serial.c v2.0 2017-06-30 [ 4.011231] 11020000.serial: ttyS1 at MMIO 0x11020000 (irq = 88) is a rk29_serial.1 [ 4.011719] serial 11020000.serial: membase e23f6000 [ 4.018089] loop: module loaded [ 4.018908] zram: Created 1 device(s) [ 4.019180] i2c-core: driver [mpu6050B1] using legacy suspend method [ 4.019203] i2c-core: driver [mpu6050B1] using legacy resume method [ 4.019228] mpu_init: Probe name mpu6050B1 [ 4.019541] ak8963_mod_init: Probe name ak8963_mod [ 4.021094] SCSI Media Changer driver v0.25 [ 4.021782] tun: Universal TUN/TAP device driver, 1.6 [ 4.021817] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 4.022087] vmac_init. [ 4.023095] stmmac_probe_config_dt: Can not read property: pmu_regulator. [ 4.023125] stmmac_probe_config_dt: clock input/output? (output). [ 4.023146] stmmac_probe_config_dt: TX delay(0x26). [ 4.023167] stmmac_probe_config_dt: RX delay(0x11). [ 4.023188] stmmac_probe_config_dt: internal PHY/external PHY? (internal). [ 4.023360] stmmc_pltfr_init: [ 4.023403] stmmc_pltfr_init: ERROR: Get power-gpio failed. [ 4.023424] stmmc_pltfr_init: ERROR: Get reset-gpio failed. [ 4.023482] stmmc_pltfr_init: init for RMII [ 4.023789] stmmac - user ID: 0x10, Synopsys ID: 0x35 [ 4.023809] Normal descriptors [ 4.023825] Ring mode enabled [ 4.023842] DMA HW capability register supported [ 4.023860] RX Checksum Offload Engine supported (type 2) [ 4.023878] TX Checksum insertion supported [ 4.023894] Wake-Up On Lan supported [ 4.023979] Enable RX Mitigation via HW Watchdog Timer [ 4.024828] PPP generic driver version 2.4.2 [ 4.025184] PPP BSD Compression module registered [ 4.025211] PPP Deflate Compression module registered [ 4.025251] PPP MPPE Compression module registered [ 4.025273] NET: Registered protocol family 24 [ 4.025330] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled). [ 4.025350] CSLIP: code copyright 1989 Regents of the University of California. [ 4.025370] Rockchip WiFi SYS interface (V1.00) ... [ 4.025440] [ 4.025459] ======================================================= [ 4.025478] ==== Launching Wi-Fi driver! (Powered by Rockchip) ==== [ 4.025495] ======================================================= [ 4.025513] Realtek 8188EU USB WiFi driver (Powered by Rockchip) init. [ 4.025533] [WLAN_RFKILL]: rockchip_wifi_power: 1 [ 4.025552] [WLAN_RFKILL]: rockchip_wifi_power: rfkill-wlan driver has not Successful initialized [ 4.025571] RTW: module init start [ 4.025589] RTW: rtl8188eu v5.2.2_19960.20161226 [ 4.025607] RTW: build time: Aug 6 2018 17:38:56 [ 4.025779] usbcore: registered new interface driver rtl8188eu [ 4.025799] RTW: module init ret=0 [ 4.025816] ======================================================= [ 4.025835] ==== Launching Wi-Fi driver! (Powered by Rockchip) ==== [ 4.025851] ======================================================= [ 4.025872] WiFi driver (Powered by Rockchip,Ver 5.10.WFD.OOB.64bit) init. [ 4.025891] dhd_module_init: in [ 4.025908] ======== dhd_wlan_init_plat_data ======== [ 4.025927] dhd_wlan_init_gpio: GPIO(WL_REG_ON) = -1 [ 4.025946] dhd_wlan_init_gpio: GPIO(WL_HOST_WAKE) = -1 [ 4.025965] [WLAN_RFKILL]: rockchip_wifi_get_oob_irq: Enter [ 4.025984] [WLAN_RFKILL]: rockchip_wifi_get_oob_irq: rfkill-wlan driver has not Successful initialized [ 4.026004] dhd_wlan_init_gpio: host_oob_irq: -1 [ 4.026025] dhd_wlan_init_gpio: host_oob_irq_flags=0x414 [ 4.026042] dhd_wifi_platform_load: Enter [ 4.026088] Power-up adapter 'DHD generic adapter' [ 4.026169] wifi_platform_set_power = 1 [ 4.026190] ======== PULL WL_REG_ON(-1) HIGH! ======== [ 4.026211] [WLAN_RFKILL]: rockchip_wifi_power: 1 [ 4.026229] [WLAN_RFKILL]: rockchip_wifi_power: rfkill-wlan driver has not Successful initialized [ 4.224142] wifi_platform_bus_enumerate device present 1 [ 4.224182] ======== Card detection to detect SDIO card! ======== [ 4.224203] [WLAN_RFKILL]: rockchip_wifi_power: 0 [ 4.224222] [WLAN_RFKILL]: rockchip_wifi_power: rfkill-wlan driver has not Successful initialized [ 4.234091] [WLAN_RFKILL]: rockchip_wifi_power: 1 [ 4.234127] [WLAN_RFKILL]: rockchip_wifi_power: rfkill-wlan driver has not Successful initialized [ 4.234147] sdio: host isn't initialization successfully. [ 6.201989] failed to power up DHD generic adapter, 0 retry left [ 6.217856] wifi_platform_set_power = 0 [ 6.217891] ======== PULL WL_REG_ON(-1) LOW! ======== [ 6.217913] [WLAN_RFKILL]: rockchip_wifi_power: 0 [ 6.217932] [WLAN_RFKILL]: rockchip_wifi_power: rfkill-wlan driver has not Successful initialized [ 6.217953] wifi_platform_bus_enumerate device present 0 [ 6.217971] ======== Card detection to remove SDIO card! ======== [ 6.217990] sdio: host isn't initialization successfully. [ 6.218008] failed to power up DHD generic adapter, max retry reached** [ 6.218065] unregister wifi platform drivers [ 6.218086] wifi_platform_bus_enumerate device present 0 [ 6.218102] ======== Card detection to remove SDIO card! ======== [ 6.218120] sdio: host isn't initialization successfully. [ 6.218139] ======== dhd_wlan_deinit_plat_data ======== [ 6.218161] dhd_module_init: Failed to load the driver, try cnt 0 [ 6.218215] dhd_module_init: Failed to load driver max retry reached** [ 6.218232] dhd_module_init: Exit err=-19 [ 6.218253] esp_mem_init enter date Aug 6 2018 17:38:54 [ 6.218273] esp_mem_init VERSION [V2.5] [ 6.218344] esp_mem_init complete [ 6.218489] usbcore: registered new interface driver catc [ 6.218585] usbcore: registered new interface driver kaweth [ 6.218607] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 6.218690] usbcore: registered new interface driver pegasus [ 6.218771] usbcore: registered new interface driver rtl8150 [ 6.218855] usbcore: registered new interface driver r8152 [ 6.218879] hso: drivers/net/usb/hso.c: Option Wireless [ 6.219025] usbcore: registered new interface driver hso [ 6.219145] usbcore: registered new interface driver asix [ 6.219231] usbcore: registered new interface driver ax88179_178a [ 6.219312] usbcore: registered new interface driver cdc_ether [ 6.219395] usbcore: registered new interface driver cdc_eem [ 6.219476] usbcore: registered new interface driver dm9601 [ 6.219554] usbcore: registered new interface driver dm9620 [ 6.219666] usbcore: registered new interface driver smsc75xx [ 6.219764] usbcore: registered new interface driver smsc95xx [ 6.219849] usbcore: registered new interface driver gl620a [ 6.219930] usbcore: registered new interface driver net1080 [ 6.220010] usbcore: registered new interface driver plusb [ 6.220090] usbcore: registered new interface driver rndis_host [ 6.220167] usbcore: registered new interface driver cdc_subset [ 6.220261] usbcore: registered new interface driver zaurus [ 6.220344] usbcore: registered new interface driver MOSCHIP usb-ethernet driver [ 6.220478] usbcore: registered new interface driver int51x1 [ 6.220563] usbcore: registered new interface driver kalmia [ 6.220644] usbcore: registered new interface driver ipheth [ 6.220731] usbcore: registered new interface driver sierra_net [ 6.220817] usbcore: registered new interface driver cx82310_eth [ 6.220931] usbcore: registered new interface driver cdc_ncm [ 6.221018] usbcore: registered new interface driver qmi_wwan [ 6.221100] usbcore: registered new interface driver cdc_mbim [ 6.221121] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 6.221142] ehci-platform: EHCI generic platform driver [ 6.221814] ehci-platform 30080000.ehci0: EHCI Host Controller [ 6.221889] ehci-platform 30080000.ehci0: new USB bus registered, assigned bus number 1 [ 6.222541] ehci-platform 30080000.ehci0: irq 48, io mem 0x30080000 [ 6.241344] ehci-platform 30080000.ehci0: USB 2.0 started, EHCI 1.00 [ 6.241514] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 6.241544] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.241571] usb usb1: Product: EHCI Host Controller [ 6.241595] usb usb1: Manufacturer: Linux 3.10.104 ehci_hcd [ 6.241619] usb usb1: SerialNumber: 30080000.ehci0 [ 6.242621] hub 1-0:1.0: USB hub found [ 6.242669] hub 1-0:1.0: 1 port detected [ 6.243292] ehci-platform 300c0000.ehci1: EHCI Host Controller [ 6.243347] ehci-platform 300c0000.ehci1: new USB bus registered, assigned bus number 2 [ 6.243916] ehci-platform 300c0000.ehci1: irq 51, io mem 0x300c0000 [ 6.261064] ehci-platform 300c0000.ehci1: USB 2.0 started, EHCI 1.00 [ 6.261219] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 6.261245] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.261271] usb usb2: Product: EHCI Host Controller [ 6.261296] usb usb2: Manufacturer: Linux 3.10.104 ehci_hcd [ 6.261317] usb usb2: SerialNumber: 300c0000.ehci1 [ 6.262208] hub 2-0:1.0: USB hub found [ 6.262275] hub 2-0:1.0: 1 port detected [ 6.262821] ehci-platform 30100000.ehci2: EHCI Host Controller [ 6.262871] ehci-platform 30100000.ehci2: new USB bus registered, assigned bus number 3 [ 6.263452] ehci-platform 30100000.ehci2: irq 98, io mem 0x30100000 [ 6.280730] ehci-platform 30100000.ehci2: USB 2.0 started, EHCI 1.00 [ 6.280891] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 [ 6.280920] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.280946] usb usb3: Product: EHCI Host Controller [ 6.280969] usb usb3: Manufacturer: Linux 3.10.104 ehci_hcd [ 6.280993] usb usb3: SerialNumber: 30100000.ehci2 [ 6.281812] hub 3-0:1.0: USB hub found [ 6.281887] hub 3-0:1.0: 1 port detected [ 6.282663] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 6.282933] ohci-platform: OHCI generic platform driver [ 6.283154] ohci-platform 300a0000.ohci0: Generic Platform OHCI controller [ 6.283206] ohci-platform 300a0000.ohci0: new USB bus registered, assigned bus number 4 [ 6.283292] ohci-platform 300a0000.ohci0: irq 49, io mem 0x300a0000 [ 6.343782] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 6.343829] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.343857] usb usb4: Product: Generic Platform OHCI controller [ 6.343882] usb usb4: Manufacturer: Linux 3.10.104 ohci_hcd [ 6.343907] usb usb4: SerialNumber: 300a0000.ohci0 [ 6.344806] hub 4-0:1.0: USB hub found [ 6.344853] hub 4-0:1.0: 1 port detected [ 6.345297] ohci-platform 300e0000.ohci1: Generic Platform OHCI controller [ 6.345351] ohci-platform 300e0000.ohci1: new USB bus registered, assigned bus number 5 [ 6.345430] ohci-platform 300e0000.ohci1: irq 52, io mem 0x300e0000 [ 6.402821] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 [ 6.402864] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.402891] usb usb5: Product: Generic Platform OHCI controller [ 6.402914] usb usb5: Manufacturer: Linux 3.10.104 ohci_hcd [ 6.402936] usb usb5: SerialNumber: 300e0000.ohci1 [ 6.403755] hub 5-0:1.0: USB hub found [ 6.403799] hub 5-0:1.0: 1 port detected [ 6.404245] ohci-platform 30120000.ohci2: Generic Platform OHCI controller [ 6.404299] ohci-platform 30120000.ohci2: new USB bus registered, assigned bus number 6 [ 6.404380] ohci-platform 30120000.ohci2: irq 99, io mem 0x30120000 [ 6.461861] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 [ 6.461903] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.461929] usb usb6: Product: Generic Platform OHCI controller [ 6.461951] usb usb6: Manufacturer: Linux 3.10.104 ohci_hcd [ 6.461975] usb usb6: SerialNumber: 30120000.ohci2 [ 6.462818] hub 6-0:1.0: USB hub found [ 6.462862] hub 6-0:1.0: 1 port detected [ 6.463492] usbcore: registered new interface driver cdc_acm [ 6.463517] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 6.463653] usbcore: registered new interface driver usblp [ 6.463749] usbcore: registered new interface driver cdc_wdm [ 6.463970] usbcore: registered new interface driver usb-storage [ 6.464057] usbcore: registered new interface driver ums-alauda [ 6.464139] usbcore: registered new interface driver ums-cypress [ 6.464225] usbcore: registered new interface driver ums-datafab [ 6.464310] usbcore: registered new interface driver ums_eneub6250 [ 6.464391] usbcore: registered new interface driver ums-freecom [ 6.464473] usbcore: registered new interface driver ums-isd200 [ 6.464557] usbcore: registered new interface driver ums-jumpshot [ 6.464637] usbcore: registered new interface driver ums-karma [ 6.464729] usbcore: registered new interface driver ums-onetouch [ 6.464813] usbcore: registered new interface driver ums-sddr09 [ 6.464900] usbcore: registered new interface driver ums-sddr55 [ 6.464979] usbcore: registered new interface driver ums-usbat [ 6.465192] usbcore: registered new interface driver usbserial [ 6.465279] usbcore: registered new interface driver usbserial_generic [ 6.465343] usbserial: USB Serial support registered for generic [ 6.465435] usbcore: registered new interface driver option [ 6.465507] usbserial: USB Serial support registered for GSM modem (1-port) [ 6.465926] usbcore: registered new interface driver trancevibrator [ 6.465947] usb20_otg: version 3.10a 21-DEC-2012 [ 6.466883] e2680040 [ 6.466910] Core Release: 3.10a [ 6.466929] Setting default values for core params [ 6.467238] Using Buffer DMA mode [ 6.467261] Periodic Transfer Interrupt Enhancement - disabled [ 6.467281] Multiprocessor Interrupt Enhancement - disabled [ 6.467299] OTG VER PARAM: 0, OTG VER FLAG: 0 [ 6.467317] ^^^^^^^^^^^^^^^^^Device Mode [ 6.467344] Dedicated Tx FIFOs mode [ 6.467378] pcd_init otg_dev = dded3500 [ 6.467791] usb20_otg 30040000.otg: DWC OTG Controller [ 6.467850] usb20_otg 30040000.otg: new USB bus registered, assigned bus number 7 [ 6.467920] usb20_otg 30040000.otg: irq 55, io mem 0x00000000 [ 6.468048] usb usb7: New USB device found, idVendor=1d6b, idProduct=0002 [ 6.468075] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.468101] usb usb7: Product: DWC OTG Controller [ 6.468125] usb usb7: Manufacturer: Linux 3.10.104 dwc_otg_hcd [ 6.468150] usb usb7: SerialNumber: 30040000.otg [ 6.469078] hub 7-0:1.0: USB hub found [ 6.469122] hub 7-0:1.0: 1 port detected [ 6.469718] usb20_host: version 3.10a 21-DEC-2012 [ 6.471723] usbcore: registered new interface driver xpad [ 6.471860] usbcore: registered new interface driver usb_acecad [ 6.471968] usbcore: registered new interface driver aiptek [ 6.472072] usbcore: registered new interface driver gtco [ 6.472172] usbcore: registered new interface driver hanwang [ 6.472273] usbcore: registered new interface driver kbtab [ 6.472401] usbcore: registered new interface driver wacom [ 6.472582] ==gsl_ts_init== [ 6.472650] ret=0 [ 6.472713] i2c-core: driver [gslX680] using legacy suspend method [ 6.472735] i2c-core: driver [gslX680] using legacy resume method [ 6.473611] sensor_register_slave:mma8452,id=17 [ 6.473637] sensor_register_slave:mma7660,id=18 [ 6.473656] sensor_register_slave:gs_mc3230,id=23 [ 6.473674] [Gsensor] gsensor_init [ 6.473694] sensor_register_slave:mpu6880_acc,id=24 [ 6.473714] sensor_register_slave:mpu6500_acc,id=25 [ 6.473734] sensor_register_slave:bma2xx_acc,id=26 [ 6.473753] sensor_register_slave:akm8963,id=30 [ 6.473773] sensor_register_slave:cm3217,id=51 [ 6.473790] sensor_register_slave:cm3218,id=52 [ 6.473809] sensor_register_slave:ls_stk3410,id=60 [ 6.474486] .. rk pwm remotectl v1.1 init [ 6.474575] ####################################### [ 6.474663] ################22222####################### [ 6.474725] ######################3333################# [ 6.474789] ########################4444############### [ 6.474850] #############################555########## [ 6.475213] input: 110b0030.pwm as /devices/110b0030.pwm/input/input0 [ 6.475924] remotectl-pwm 110b0030.pwm: Missing psci property in the DT. [ 6.566137] dwc_otg_hcd_suspend, usb device mode [ 7.112328] rtc_hym8563 0-0051: rtc core: registered hym8563 as rtc0 [ 7.112420] i2c /dev entries driver [ 7.113013] IR NEC protocol handler initialized [ 7.113035] IR RC5(x) protocol handler initialized [ 7.113055] IR RC6 protocol handler initialized [ 7.113072] IR JVC protocol handler initialized [ 7.113089] IR Sony protocol handler initialized [ 7.113107] IR RC5 (streamzap) protocol handler initialized [ 7.113123] IR SANYO protocol handler initialized [ 7.113140] IR MCE Keyboard/mouse protocol handler initialized [ 7.113497] usbcore: registered new interface driver uvcvideo [ 7.113532] USB Video Class driver (1.1.1) [ 7.113555] CamSys driver version: v0.35.0, CamSys head file version: v0.13.0 [ 7.113579] E:camsys_soc_init(36): camsys isn't support soc: 0x32283002! [ 7.114242] not find test_power_init dev node [ 7.114323] i2c-core: driver [bq27320] using legacy suspend method [ 7.114344] i2c-core: driver [bq27320] using legacy resume method [ 7.115663] ===========net_led_probe start=========== [ 7.115807] ===========net_led_probe end=========== [ 7.116051] ===========remote_led_probe start=========== [ 7.116158] ===========remote_led_probe end=========== [ 7.116390] ===========suspend_led_probe start=========== [ 7.116532] ===========suspend_led_probe end=========== [ 7.116951] rockchip_temp_probe,line=384 [ 7.117560] tsadc 11150000.tsadc: Missing tsadc_low_temp in the DT. [ 7.176143] tsadc 11150000.tsadc: initialized [ 7.177077] device-mapper: uevent: version 1.0.3 [ 7.177615] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com [ 7.178074] Bluetooth: HCI UART driver ver 2.2 [ 7.178102] Bluetooth: HCI H4 protocol initialized [ 7.178121] Bluetooth: HCILL protocol initialized [ 7.178140] rtk_btusb: RTKBT_RELEASE_NAME: 20170109_TV_ANDROID_6.x [ 7.178159] rtk_btusb: Realtek Bluetooth USB driver module init, version 4.1.2 [ 7.178178] rtk_btusb: Register usb char device interface for BT driver [ 7.178579] usbcore: registered new interface driver rtk_btusb [ 7.179005] cpufreq version 1.0, suspend freq 1008 MHz [ 7.179570] cpuidle: using governor ladder [ 7.179595] cpuidle: using governor menu [ 7.179675] Synopsys Designware Multimedia Card Interface Driver [ 7.179697] MHSC version = Ver 2.00 2015-06-10 [ 7.180247] dwmmc_rockchip 30020000.rksdmmc: Version ID is 270a [ 7.180341] dwmmc_rockchip 30020000.rksdmmc: failed to get hpclk_mmc [ 7.180807] dwmmc_rockchip 30020000.rksdmmc: Using internal DMA controller. [ 7.181155] dwmmc_rockchip 30020000.rksdmmc: dw_mci_init_slot: fmin=400000, fmax=125000000 [mmc0] [ 7.195909] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out 800000Hz for init[mmc0] [ 7.215598] dwmmc_rockchip 30020000.rksdmmc: DW MMC controller at irq 46, 32 bit host data width, 256 deep fifo [ 7.215638] dwmmc_rockchip 30020000.rksdmmc: 1 slots initialized [ 7.216436] dwmmc_rockchip 30000000.rksdmmc: Version ID is 270a [ 7.216528] dwmmc_rockchip 30000000.rksdmmc: failed to get hpclk_mmc [ 7.216967] dwmmc_rockchip 30000000.rksdmmc: Using internal DMA controller. [ 7.217333] dwmmc_rockchip 30000000.rksdmmc: dw_mci_init_slot: fmin=400000, fmax=37500000 [mmc1] [ 7.217632] dwmmc_rockchip 30000000.rksdmmc: mmc1: No udbg pinctrl found! [ 7.235219] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out 800000Hz for init[mmc1] [ 7.255090] dwmmc_rockchip 30000000.rksdmmc: DW MMC controller at irq 44, 32 bit host data width, 256 deep fifo [ 7.255166] dwmmc_rockchip 30000000.rksdmmc: 1 slots initialized [ 7.256396] dwmmc_rockchip 30010000.rksdmmc: Version ID is 270a [ 7.256534] dwmmc_rockchip 30010000.rksdmmc: failed to get hpclk_mmc [ 7.257113] dwmmc_rockchip 30010000.rksdmmc: Using internal DMA controller. [ 7.257618] dwmmc_rockchip 30010000.rksdmmc: dw_mci_init_slot: fmin=200000, fmax=37500000 [mmc2] [ 7.274658] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out 800000Hz for init[mmc2] [ 7.294446] dwmmc_rockchip 30010000.rksdmmc: DW MMC controller at irq 45, 32 bit host data width, 256 deep fifo [ 7.294516] dwmmc_rockchip 30010000.rksdmmc: 1 slots initialized [ 7.295247] leds-gpio power-led.31: pins are not configured from the driver [ 7.296230] hidraw: raw HID events driver (C) Jiri Kosina [ 7.303525] usbcore: registered new interface driver usbhid [ 7.303594] usbhid: USB HID core driver [ 7.304271] ashmem: initialized [ 7.304826] logger: created 256K log 'log_main' [ 7.305327] logger: created 256K log 'log_events' [ 7.305816] logger: created 256K log 'log_radio' [ 7.306300] logger: created 256K log 'log_system' [ 7.308572] rknandbase v1.1 2016-11-08 [ 7.309198] rknand 30030000.nandc: rknand_probe clk rate = 150000000 [ 7.309523] No.1 FLASH ID:2c 64 44 32 a5 0 [ 7.310156] ECC:60 [ 7.310221] FTL version: 5.0.47 20171120 [ 7.441067] FtlInit 0 [ 7.441405] parameter: 0x000000000 -- 0x000400000 (4 MB) [ 7.441989] uboot: 0x000400000 -- 0x000800000 (4 MB) [ 7.442328] trust: 0x000800000 -- 0x001000000 (8 MB) [ 7.442617] misc: 0x001000000 -- 0x001400000 (4 MB) [ 7.442913] baseparamer: 0x001400000 -- 0x001500000 (1 MB) [ 7.443202] resource: 0x001500000 -- 0x002400000 (15 MB) [ 7.443490] kernel: 0x002400000 -- 0x003000000 (12 MB) [ 7.443787] boot: 0x003000000 -- 0x003c00000 (12 MB) [ 7.444095] recovery: 0x003c00000 -- 0x005c00000 (32 MB) [ 7.444394] backup: 0x005c00000 -- 0x009c00000 (64 MB) [ 7.444695] cache: 0x009c00000 -- 0x011c00000 (128 MB) [ 7.445010] metadata: 0x011c00000 -- 0x012c00000 (16 MB) [ 7.445335] kpanic: 0x012c00000 -- 0x013000000 (4 MB) [ 7.445649] system: 0x013000000 -- 0x0d3000000 (3072 MB) [ 7.445958] userdata: 0x0d3000000 -- 0x1d4000000 (4112 MB) [ 7.450721] vendor storage 524b5644,2,2 [ 7.453598] vendor storage 524b5644,3,3 [ 7.458955] rockchip-spdif 100d0000.spdif: spdif ready. [ 7.550114] Using Buffer DMA mode [ 7.550147] Periodic Transfer Interrupt Enhancement - disabled [ 7.550158] Multiprocessor Interrupt Enhancement - disabled [ 7.550170] OTG VER PARAM: 0, OTG VER FLAG: 0 [ 7.550181] ^^^^^^^^^^^^^^^^^^Host Mode [ 7.551968] rk322x-audio rockchip_audio.28: rk322x-hifi <-> 100b0000.i2s1 mapping ok [ 7.556070] rockchip-hdmi-i2s rockchip_hdmi_i2s.30: rk-hdmi-i2s-hifi <-> 100c0000.i2s0 mapping ok [ 7.557013] u32 classifier [ 7.557032] Actions configured [ 7.557047] Netfilter messages via NETLINK v0.30. [ 7.557137] nf_conntrack version 0.5.0 (15414 buckets, 61656 max) [ 7.557664] ctnetlink v0.93: registering with nfnetlink. [ 7.557763] NF_TPROXY: Transparent proxy support initialized, version 4.1.0 [ 7.557775] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd. [ 7.558314] xt_time: kernel timezone is -0000 [ 7.558654] ip_tables: (C) 2000-2006 Netfilter Core Team [ 7.558886] arp_tables: (C) 2002 David S. Miller [ 7.558949] TCP: cubic registered [ 7.558959] Initializing XFRM netlink socket [ 7.559381] NET: Registered protocol family 10 [ 7.560366] mip6: Mobile IPv6 [ 7.560417] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 7.560631] sit: IPv6 over IPv4 tunneling driver [ 7.561256] NET: Registered protocol family 17 [ 7.561302] NET: Registered protocol family 15 [ 7.561406] Bridge firewalling registered [ 7.561427] Ebtables v2.0 registered [ 7.561725] Bluetooth: RFCOMM TTY layer initialized [ 7.561779] Bluetooth: RFCOMM socket layer initialized [ 7.561791] Bluetooth: RFCOMM ver 1.11 [ 7.561802] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 7.561811] Bluetooth: BNEP filters: protocol multicast [ 7.561829] Bluetooth: BNEP socket layer initialized [ 7.561840] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 7.561856] Bluetooth: HIDP socket layer initialized [ 7.561957] l2tp_core: L2TP core driver, V2.0 [ 7.561980] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 7.561990] [WLAN_RFKILL]: Enter rfkill_wlan_init [ 7.562247] [WLAN_RFKILL]: Enter rfkill_wlan_probe [ 7.562266] [WLAN_RFKILL]: can't find rockchip,grf property [ 7.562279] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = rtl8189fs [ 7.562291] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control. [ 7.562303] [WLAN_RFKILL]: wlan_platdata_parse_dt: disable wifi io reference voltage control. [ 7.562318] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio. [ 7.562393] [WLAN_RFKILL]: wlan_platdata_parse_dt: get property: WIFI,poweren_gpio = 90, flags = 0. [ 7.562439] [WLAN_RFKILL]: wlan_platdata_parse_dt: get property: WIFI,host_wake_irq = 28, flags = 0. [ 7.562453] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio [ 7.562508] [WLAN_RFKILL]: rockchip_wifi_power: 0 [ 7.562521] [BT_RFKILL]: rfkill_get_bt_power_state: rfkill-bt driver has not Successful initialized [ 7.599301] Init: Power Port (0) [ 7.599374] 30040000.otg resume, HPRT0:0x1000 [ 7.599499] 30040000.otg suspend, HPRT0:0x1000 [ 7.668179] [WLAN_RFKILL]: wifi shut off power. [ 7.668245] [WLAN_RFKILL]: rockchip_wifi_ref_voltage: 0 [ 7.668276] [WLAN_RFKILL]: rockchip_wifi_ref_voltage: wifi io reference voltage control is disabled. [ 7.678162] [WLAN_RFKILL]: rockchip_wifi_power: 1 [ 7.678214] [BT_RFKILL]: rfkill_get_bt_power_state: rfkill-bt driver has not Successful initialized [ 7.678251] [WLAN_RFKILL]: rockchip_wifi_ref_voltage: 1 [ 7.678280] [WLAN_RFKILL]: rockchip_wifi_ref_voltage: wifi io reference voltage control is disabled. [ 7.786262] [WLAN_RFKILL]: wifi turn on power. 90 [ 7.786313] mmc2:mmc host rescan start! [ 7.786361] [WLAN_RFKILL]: Exit rfkill_wlan_probe [ 7.786535] [BT_RFKILL]: Enter rfkill_rk_init [ 7.787336] Key type dns_resolver registered [ 7.792267] rk322x_suspend_init: pm_ctrbits = 0x11806 [ 7.792373] Registering SWP/SWPB emulation handler [ 7.792418] rockchip_uboot_mem_late_init: Freeing uboot logo memory: 0x02000000@0x9dc00000 [ 7.807232] ddrfreq: verion 1.2 20140526 [ 7.846130] ddrfreq: normal 600MHz performance 0MHz low_power 0MHz video_1080p 0MHz video_4k 700MHz dualview 0MHz idle 0MHz suspend 0MHz reboot 600MHz video_4k_10b 720MHz [ 7.846251] ddrfreq: auto-freq=0 [ 7.846271] ddrfreq: auto-freq-table epmty! [ 7.847742] regulator-dummy: disabling [ 7.848185] pcd_pullup, is_on 0 [ 7.848221] WARN::dwc_otg_handle_mode_mismatch_intr:69: Mode Mismatch Interrupt: currently in Host mode [ 7.848221] [ 7.848265] WARN::dwc_otg_handle_mode_mismatch_intr:69: Mode Mismatch Interrupt: currently in Host mode [ 7.848265] [ 7.848407] file system registered [ 7.850192] android_usb gadget: Mass Storage Function, version: 2009/09/11 [ 7.850215] android_usb gadget: Number of LUNs=2 [ 7.850234] lun0: LUN: removable file: (no medium) [ 7.850252] lun1: LUN: removable file: (no medium) [ 7.850849] android_usb gadget: android_usb ready [ 7.850976] sensor_init: Probe name sensors [ 7.851017] sensor-dev.c v1.4 add angle calculation support between two gsensors 2013-09-01 [ 7.899127] rtc_hym8563 0-0051: hctosys: invalid date/time [ 7.913547] rockchip-spdif-card rockchip_spdif_card.29: rk-hdmi-spdif-hifi <-> 100d0000.spdif mapping ok [ 7.915855] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 414; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '-v3.10.92-28033-gae45312', rk_ko_ver is '5', built at '17:38:20', on 'Aug 6 2018'. [ 7.916356] mali-utgard 20001000.gpu: mali_platform_device->num_resources = 13 [ 7.916407] mali-utgard 20001000.gpu: resource[0].start = 0x0x20001000 [ 7.916446] mali-utgard 20001000.gpu: resource[1].start = 0x0x20000000 [ 7.916485] mali-utgard 20001000.gpu: resource[2].start = 0x0x20003000 [ 7.916524] mali-utgard 20001000.gpu: resource[3].start = 0x0x20008000 [ 7.916562] mali-utgard 20001000.gpu: resource[4].start = 0x0x20004000 [ 7.916603] mali-utgard 20001000.gpu: resource[5].start = 0x0x2000a000 [ 7.916642] mali-utgard 20001000.gpu: resource[6].start = 0x0x20005000 [ 7.916682] mali-utgard 20001000.gpu: resource[7].start = 0x0x00000026 [ 7.916719] mali-utgard 20001000.gpu: resource[8].start = 0x0x00000025 [ 7.916757] mali-utgard 20001000.gpu: resource[9].start = 0x0x00000024 [ 7.916796] mali-utgard 20001000.gpu: resource[10].start = 0x0x00000025 [ 7.916836] mali-utgard 20001000.gpu: resource[11].start = 0x0x00000024 [ 7.916876] mali-utgard 20001000.gpu: resource[12].start = 0x0x00000025 [ 7.917003] mali-utgard 20001000.gpu: freq: 200000000, min_threshold: 0, max_threshold: 70 [ 7.917051] mali-utgard 20001000.gpu: freq: 300000000, min_threshold: 61, max_threshold: 85 [ 7.917096] mali-utgard 20001000.gpu: freq: 400000000, min_threshold: 73, max_threshold: 100 [ 7.917245] mali-utgard 20001000.gpu: initial freq = 200000000 [ 7.921731] Mali: Mali device driver loaded [ 7.923054] usbcore: registered new interface driver snd-usb-audio [ 7.923091] ALSA device list: [ 7.923118] #0: RK_RK322x [ 7.923146] #1: RK-HDMI-I2S [ 7.923172] #2: RK-SPDIF-CARD [ 7.924550] Freeing unused kernel memory: 384K (c0def000 - c0e4f000) [ 7.930152] init: init first stage started! [ 8.002798] mmc_host mmc2: Bus speed (slot 0) = 37500000Hz (slot req 400000Hz, actual 398936HZ div = 47) [ 8.002865] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out 800000Hz for init[mmc2] [ 8.028616] dwmmc_rockchip 30010000.rksdmmc: exceeding card's volts [ 8.028990] mmc2 not switch iovel. [ 8.052949] mmc_host mmc2: Bus speed (slot 0) = 37500000Hz (slot req 37500000Hz, actual 37500000HZ div = 0) [ 8.053027] rk_sdmmc: BOOT dw_mci_setup_bus: argue clk_mmc workaround out normal clock [mmc2] [ 8.053314] rk_sdmmc: BOOT Bus speed=37500000Hz,Bus width=4bits.[mmc2] [ 8.054826] mmc2: new high speed SDIO card at address 0001 [ 8.183332] type=1403 audit(5.120:2): policy loaded auid=4294967295 ses=4294967295 [ 8.185387] init: (Initializing SELinux non-enforcing took 0.26s.) [ 8.200256] init: init second stage started! [ 8.214667] init: Setting ro.rk.soc=rk3229 [ 8.215212] init: property_set("ro.hardware", "rk30board") failed [ 8.223761] init: Running restorecon... [ 8.288108] vendor storage:20160801 ret = -1 [ 8.312205] init: waitpid failed: No child processes [ 8.313478] init: property_set("ro.board.platform", "rk322x") failed [ 8.314201] init: property_set("ro.opengles.version", "196609") failed [ 8.314538] init: property_set("ro.rk.screenoff_time", "2147483647") failed [ 8.315059] init: property_set("ro.rk.screenshot_enable", "true") failed [ 8.315339] init: (Loading properties from /default.prop took 0.00s.) [ 8.317987] init: (Parsing /init.bootmode.unknown.rc took 0.00s.) [ 8.318109] init: could not import file '/init.recovery.rk30board.rc' from '/init.rc': No such file or directory [ 8.318149] init: (Parsing /init.rc took 0.00s.) [ 8.318492] init: Starting service 'ueventd'... [ 8.319191] init: Starting service 'healthd'... [ 8.320004] init: Waiting for /dev/.coldboot_done... [ 8.323074] ueventd: ueventd started! [ 8.324104] type=1400 audit(5.260:3): avc: denied { mknod } for pid=118 comm="healthd" capability=27 scontext=u:r:healthd:s0 tcontext=u:r:healthd:s0 tclass=capability permissive=1 [ 8.324229] ueventd: invalid gid 'trace' [ 8.324298] type=1400 audit(5.260:4): avc: denied { write } for pid=118 comm="healthd" name="__kmsg__" dev="tmpfs" ino=6888 scontext=u:r:healthd:s0 tcontext=u:object_r:device:s0 tclass=chr_file permissive=1 [ 8.324352] type=1400 audit(5.260:5): avc: denied { open } for pid=118 comm="healthd" path="/dev/__kmsg__" dev="tmpfs" ino=6888 scontext=u:r:healthd:s0 tcontext=u:object_r:device:s0 tclass=chr_file permissive=1 [ 8.324432] type=1400 audit(5.260:6): avc: denied { unlink } for pid=118 comm="healthd" name="__kmsg__" dev="tmpfs" ino=6888 scontext=u:r:healthd:s0 tcontext=u:object_r:device:s0 tclass=chr_file permissive=1 [ 8.324463] healthd: No battery devices found [ 8.324622] healthd: battery l=100 v=0 t=42.4 h=2 st=2 chg=a [ 8.589976] ueventd: Coldboot took 0.27s. [ 8.599192] init: Waiting for /dev/.coldboot_done took 0.28s. [ 8.599333] init: /dev/hw_random not found [ 8.602400] init: /dev/hw_random not found [ 8.609953] init: write_file: Unable to open '/config/usb_gadget/g1/os_desc/b_vendor_code': No such file or directory [ 8.610176] init: write_file: Unable to open '/config/usb_gadget/g1/os_desc/qw_sign': No such file or directory [ 8.611569] android_usb: already disabled [ 8.613047] init: property 'ro.serialno' doesn't exist while expanding '${ro.serialno}' [ 8.613149] init: write: cannot expand '${ro.serialno}' [ 8.613793] drmboot: module license 'unspecified' taints kernel. [ 8.613828] Disabling lock debugging due to kernel taint [ 8.614623] drm init, 20140910 [ 8.614716] ------------[ cut here ]------------ [ 8.614757] WARNING: at fs/sysfs/dir.c:530 sysfs_add_one+0x7c/0x9c() [ 8.614780] sysfs: cannot create duplicate filename '/devices/virtual/misc/rknand_sys_storage' [ 8.614801] Modules linked in: drmboot(P+) [ 8.614838] CPU: 0 PID: 1 Comm: init Tainted: P 3.10.104 #1 [ 8.614892] [<c0014088>] (unwind_backtrace+0x0/0xe0) from [<c00118cc>] (show_stack+0x10/0x14) [ 8.614940] [<c00118cc>] (show_stack+0x10/0x14) from [<c003f320>] (warn_slowpath_common+0x4c/0x68) [ 8.614983] [<c003f320>] (warn_slowpath_common+0x4c/0x68) from [<c003f3bc>] (warn_slowpath_fmt+0x2c/0x3c) [ 8.615023] [<c003f3bc>] (warn_slowpath_fmt+0x2c/0x3c) from [<c016d22c>] (sysfs_add_one+0x7c/0x9c) [ 8.615065] [<c016d22c>] (sysfs_add_one+0x7c/0x9c) from [<c016d434>] (create_dir+0x5c/0xac) [ 8.615100] [<c016d434>] (create_dir+0x5c/0xac) from [<c016d724>] (sysfs_create_dir+0x80/0xa0) [ 8.615144] [<c016d724>] (sysfs_create_dir+0x80/0xa0) from [<c02a6128>] (kobject_add_internal+0xc8/0x1fc) [ 8.615186] [<c02a6128>] (kobject_add_internal+0xc8/0x1fc) from [<c02a6488>] (kobject_add+0x68/0x8c) [ 8.615228] [<c02a6488>] (kobject_add+0x68/0x8c) from [<c038c374>] (device_add+0xe0/0x364) [ 8.615269] [<c038c374>] (device_add+0xe0/0x364) from [<c038c688>] (device_create_vargs+0x78/0xbc) [ 8.615307] [<c038c688>] (device_create_vargs+0x78/0xbc) from [<c038c6e8>] (device_create+0x1c/0x24) [ 8.615351] [<c038c6e8>] (device_create+0x1c/0x24) from [<c034ac88>] (misc_register.part.0+0x34/0xa0) [ 8.615409] [<c034ac88>] (misc_register.part.0+0x34/0xa0) from [<bf0030ac>] (StorageSysDataInit+0xac/0xdc [drmboot]) [ 8.615461] [<bf0030ac>] (StorageSysDataInit+0xac/0xdc [drmboot]) from [<c00086a4>] (do_one_initcall+0x34/0xc8) [ 8.615504] [<c00086a4>] (do_one_initcall+0x34/0xc8) from [<c09b2b70>] (do_init_module+0x44/0x15c) 6c d 8ny6 15t59da] a <wc0e95728>] (loyoSk_fiinng tfo_rm oGduTe+!x28__>bi]onic_o pe(n_tzSyS_dfinit_atod: clou+0dxn6'ct 0xi94) /0x94) from [<c000db00>] (ret_fasSt_artsnga r+e0cxo0v/r0x38) [ y 8.(61p5620] ---d e1n2d5 )t oac e hefuc J1an 1 4f05:8008:c05d21ae --1- 8.615648] ------------[ cut here ]-b-oo--tmode = unkn-------- [ w n 8.615674] WARNING: at lib/kobject.c:196 kobject_add_internal+0x19c/0x1fc() [ 8.615696] kobject_addrecoveryn teilensayslt feaimled for rtkabande# _s y==s==_s==t==o==r===a==g=e= ==ith= =-==E= a[ l 8_s6d15vf1a8]t /odeuv/esl lionkedckin:m mdcrmlko0otp(1 0Pme nacmk/ in nandthues er am0e d [2 / s y s8te6m1 5ex48]4 CP 😕 0 PIDv/ b1 Cocmkm/:r kinain Tain_seds:te mP 0 c 3 /cache ext 4 / d3.10.10ev#/bl1o /[r n a nd.61_784] [ch<ec0001 blo[ck / r 8.na1n58d2_3u] se<rc0at1a1 80ccox0k//0xken0) fromnd_c0e0t1a1d8actc> ]0(show _5 /datastext4k+/0x10/0x1e4v) ] 6 /cushow_etatk+ /x10d/0x1ev)/ flocok/ r[k<c0an3df3_20>] (usatrn _0sl o w7 p/caustom texth_common+/dxe4v//0xl6o8ck f320> ] 8 /radi(cal_wapdn_alowte epat4h_/cdoemvm/onlo0xckc/0x/r8k)n frndm_ [r<acd00cf3lc>_ (warda_tslo w0path_fm 9 /mtis+c mtd x2cis/0x3 0) [ 10 /8u.6b15o903t m[<tcd0 0u3fb3bc>]o ot w0ar _s lo 1w1 p/cahartgeh mtd _fmtc+h0arg2c /00x c) 12 /rfesrource ommt [d<c02a6 refsc>ur c(keo b0ject_a d13d_ /ipanramteteerr mnad +0axr1a9me/0exr f0c) [ 14 /b oo t 8mtd b.6o1t5902] [< c150 /r2ecaovery m61fc>] (k rbejeccotv_ardyd 0int r 16 /backup mtdnal+0x19c/0x1fc) from [<c02a6488>] (kobject_add+0x68/0 bxackup 80) [ 8 .61598 1]1 7 </t02us6t 88t>d t(krosjt 0ct_ dd+ 018x /68ba/se0paramerx8 mt dfbrosme[par0ame8r374>]0( vic e_add+ 0x1e0/0x93 /t)m p ramd[s 8.61a60d17s]k[0<c0 c te_var (device_adI:dIn0teer/nal3SD_4)O Orom T[<:c038 /c68nt/i] t(erenial__crdea gs+0xE7xt/erxbal)SD [R OOT 8:.6160 5/mn [/<ex0t8erna8l_s8>d] _ead cmdevince create_vargs+0x78/0xbc) from [<c038c6e8>] (device_create+0x1c/0x24) [ 8.616093] [<c038c6e8>] (device_create+0x1c/0x24) from [<c034ac88>] (misc_register.part.0+0x34/0xa0) [ 8.616141] [<c034ac88>] (misc_register.part.0+0x34/0xa0) from [<bf0030ac>] (StorageSysDataInit+0xac/0xdc [drmboot]) [ 8.616189] [<bf0030ac>] (StorageSysDataInit+0xac/0xdc [drmboot]) from [<c00086a4>] (do_one_initcall+0x34/0xc8) [ 8.616229] [<c00086a4>] (do_one_initcall+0x34/0xc8) from [<c09b2b70>] (do_init_module+0x44/0x15c) [ 8.616269] [<c09b2b70>] (do_init_module+0x44/0x15c) from [<c0095728>] (SyS_finit_module+0x6c/0x94) [ 8.616314] [<c0095728>] (SyS_finit_module+0x6c/0x94) from [<c000db00>] (ret_fast_syscall+0x0/0x38) [ 8.616341] ---[ end trace efc14f5808cd21af ]--- [ 8.616367] drm init ok [ 8.617108] rk30xxnand_ko: version magic '3.10.0 SMP preempt mod_unload ARMv7 p2v8 ' should be '3.10.104 SMP preempt mod_unload ARMv7 p2v8 ' [ 8.617248] init: finit_module for "/rk30xxnand_ko.ko" failed: Exec format errorinit: insmod: open("/rk29-ipp.ko") failed: No such file or directoryinit: (Loading properties from /system/build.prop took 0.00s.) [ 8.618086] init: (Loading properties from /vendor/build.prop took 0.00s.) [ 8.618186] init: (Loading properties from /factory/factory.prop took 0.00s.) [ 8.618589] fs_mgr: Warning: unknown flag resize [ 8.618950] init: /recovery not specified in fstab [ 8.620970] init: Starting service 'recovery'... [ 8.622314] init: Starting service 'adbd'... [ 8.628084] init: Starting service 'console'... [ 8.645887] fs_mgr: Warning: unknown flag resize [ 8.655785] EXT4-fs (rknand_cache): warning: maximal mount count reached, running e2fsck is recommended [ 8.657101] EXT4-fs (rknand_cache): mounted filesystem with ordered data mode. Opts: (null) [ 8.659735] fs_mgr: Warning: unknown flag resize === start void dumpCmdArgs(int, char **):235 === argv[0] = /sbin/recovery. (void setFlashPoint():223) sdcard is /dev/block/mmcblk0. emmc_point is /dev/block/mmcblk1 locale is [en_US] stage is [] reason is [(null)] cannot find/open a drm device: No such file or directory fb0 reports (possibly inaccurate): vi.bits_per_pixel = 16 vi.red.offset = 11 .length = 5 vi.green.offset = 5 .length = 6 vi.blue.offset = 0 .length = 5 fi.line_length = 3840 framebuffer: 0 (1920 x 1080) [ 8.698680] rk322x-lcdc vop0: blank mode:0 [ 8.731724] rk322x-lcdc vop0: intr post buf empty! [ 8.731762] rk322x-lcdc vop0: intr post buf empty! erasing_text: en_US (45 x 19 @ 600) [ 8.771103] rk322x-lcdc vop0: intr post buf empty! [ 8.771169] rk322x-lcdc vop0: intr post buf empty! no_command_text: en_US (82 x 19 @ 600) error_text: en_US (33 x 19 @ 600) [ 8.810454] rk322x-lcdc vop0: intr post buf empty! [ 8.810521] rk322x-lcdc vop0: intr post buf empty! [ 8.849817] rk322x-lcdc vop0: intr post buf empty! [ 8.849885] rk322x-lcdc vop0: intr post buf empty! [ 8.889177] rk322x-lcdc vop0: intr post buf empty! [ 8.889255] rk322x-lcdc vop0: intr post buf empty! installing_text: en_US (151 x 19 @ 600) [ 9.098879] EXT4-fs (rknand_metadata): warning: maximal mount count reached, running e2fsck is recommended [ 9.099928] EXT4-fs (rknand_metadata): mounted filesystem with ordered data mode. Optbs:o (onultl)m ode = unknown Command: "/sbin/recovery" [ 9.100750] type=1400 audit(6.050:7): avc: denied { open } for pid=125 comm="recovery" path="/dev/__properties__/u:object_r:secruroeboot._drolp:ik0." d.eva="tmivpfes" inob=68d36e s0cont pdarolvpik:.vms.i0sa.a tcmas.=feilter permisfsiuvet1:seecuare7boot_ 1da lvi devnieldc {p gota.ttrh }e hfor d 5pid0= dalv5i .vomm.="xr2eoovety-Xmasth6="m/ sdalevck.rebmoohe_pproap:xs0r" deev8="r mpfs" ino=d6836 saconltiex.tvm.:re:apemiverny:fs0 tcroet=ext12uk:ob pctd_r:secualrviek.vomt._erapps:s0 trtsisz=ef1ilm edarmiik.ivme.ap1pi m 9efo0rm009=] ztype 14d0alvik .udm.us(e.j0t50:r9):oavile: =dtrnuied { odaln i} .for. peadpg1r25w cothl=imrito=192very texl" ik.vvm".imagempfds" ex2no=t6-X37s s6con dal"vpka.hm=."stadcvk/__tprrpceet-fesle_=/ud:tbaject_nr/pproaee_p.ropxts datlvi=uv:m.:imcagveery:s0ex2oatt-Xxmx==:4omj dalt_vr:k.pvp.oheaprtop:s0 tcltasts=lfilza piorn=i0ss.iv7e=1 [ 9.101065] type=140r0 oa.cdoinf(g6.0en0a:l10):.avrem otdecioetd o { fgaelasttr } for pid=125 comm="recrovoery" pbuihld".fdiegv/_p_prrpeittieA_n_r/u:idb/rec32_2:px_obo_p/rok3:2sx_ oxev=o"t7.1pf/N"HGi4o7K6/akr7 dsco-t0e80=61:74:0rucsorvere:sbug/ttoenttekxt=su: ject_r:pppoepm.depxoopt:.b0o tt=veass=firle ifye-pmiosfilve=1 p9.101m.dex]optt.peb1-4t00 audispee(-6pr0o0fi11) cpmavce:o pd.eninsda l { openin}e fpor etp-in=ly25 es__/upm.bjecxo_pt.:cg-sdetx_prop:pt=" peeed=-"rmopifse p"m.dex opto.=i68s38 -scbontoott=intr:rpereot-ornyl:s0ytc stmxdt=xu:pobjsecat_redct-gtappk=spreop: p m.tdexopc.lnssys=-illib permirs=sivee=1d pm.d e o9.t0.1o27c5] dt-dpe=exo00t aupdiet(6.0 eni 5ro0.rk12s):ca=vkc: 22d =ro.r5k scosmte"mraeco.vetrableytU"I= pfaalsteh _prop:rk/.syprtopembtares_vo/u:objicei_c:oc=tsrgts s0" drev.=Matsspft"oraigo=68=8 slsoent tcrk.hxdtiu_enrabelceove=yr:ue ron.rk.flteht_=nu:obbljecettrr:ect grot._rk.homeop:ase0 bclaasss=e=ilt tp:er/miwsw.gvo=o gle.com/webhp?client={CID}&source=android-home ro.rk.def_brightness=200 ro.rk.screenoff_time=2147483647 ro.rk.screenshot_enable=true ro.rk.LowBatteryBrightness=true ro.rk.install_non_market_apps=false ro.sf.hwrotation=0 ro.sf.lcd_density=240 ro.sf.fakerotation=false ro.sf.lcdc_composer=0 ro.adb.secure=0 ro.com.google.gmsversion=7.1_r9 ro.com.android.dataroaming=true ro.com.widevine.cachesize=16777216 ro.boot.noril=true ro.boot.console=ttyFIQ0 ro.boot.selinux=permissive ro.boot.hardware=rk30board ro.hdmi.device_type=4 ro.hwui.path_cache_size=32 ro.hwui.layer_cache_size=48 ro.hwui.texture_cache_size=72 ro.hwui.disable_scissor_opt=true ro.hwui.gradient_cache_size=1 ro.hwui.r_buffer_cache_size=8 ro.hwui.drop_shadow_cache_size=6 ro.hwui.text_large_cache_width=2048 ro.hwui.text_small_cache_width=1024 ro.hwui.text_large_cache_height=1024 ro.hwui.text_small_cache_height=1024 ro.hwui.texture_cache_flushrate=0.4 ro.wifi.channels= ro.allow.mock.location=0 ro.audio.monitorOrientation=true ro.board.platform=rk322x ro.build.id=NHG47K ro.build.date=2018▒?08▒?06▒?星期一 17:40:06 CST ro.build.date.utc=1533548406 ro.build.host=aike5 ro.build.tags=test-keys ro.build.type=userdebug ro.build.user=akrd-52 ro.build.flavor=rk322x_box-userdebug ro.build.display.id=MXQ-4K eng.akrd-52.20180806.174006 ro.build.product=rk322x_box ro.build.version.sdk=25 ro.build.version.base_os= ro.build.version.release=7.1.2 ro.build.version.codename=REL ro.build.version.incremental=eng.akrd-52.20180806.174006 ro.build.version.preview_sdk=0 ro.build.version.all_codenames=REL ro.build.version.security_patch=2017-04-05 ro.build.description=rk322x_box-userdebug 7.1.2 NHG47K eng.akrd-52.20180806.174006 test-keys ro.build.characteristics=box ro.media.maxmem=2147483648 ro.rksdk.version=RK30_ANDROID7.1.2-SDK-v1.00.00 ro.udisk.visible=true ro.secure=1 ro.target.product=box ro.tether.denied=false ro.zygote=zygote32 ro.carrier=unknown ro.default.size=100 ro.factory.tool=0 ro.factory.hasGPS=false ro.factory.hasUMS=false ro.factory.without_battery=false ro.factory.storage_suppntfs=true ro.product.cpu.abi=armeabi-v7a ro.product.cpu.abi2=armeabi ro.product.cpu.abilist=armeabi-v7a,armeabi ro.product.cpu.abilist32=armeabi-v7a,armeabi ro.product.cpu.abilist64= ro.product.name=rk322x_box ro.product.board=rk30sdk ro.product.brand=Android ro.product.model=MXQPRO ro.product.device=rk322x_box ro.product.usbfactory=rockchip_usb ro.product.manufacturer=rockchip ro.product.first_api_level=23 ro.support.lossless.bitstream=true ro.baseband=unknown ro.bootmode=unknown ro.hardware=rk30board ro.opengles.version=196609 ro.revision=0 ro.safemode.disabled=true ro.bootimage.build.date=2018▒?08▒?06▒?星期一 17:40:06 CST ro.bootimage.build.date.utc=1533548406 ro.bootimage.build.fingerprint=Android/rk322x_box/rk322x_box:7.1.2/NHG47K/akrd-508061740:userdebug/test-keys ro.bootloader=unknown ro.debuggable=1 ro.setupwizard.mode=OPTIONAL ro.setupwizard.require_network=any ro.enable_boot_charger_mode=0 sf.power.control=8847360 init.svc.adbd=running init.svc.console=running init.svc.healthd=running init.svc.ueventd=running init.svc.recovery=running rild.libargs=-d /dev/ttyACM0 rild.libpath=/system/lib64/libril-rk29-dataonly.so wifi.interface=wlan0 wifi.supplicant_scan_interval=15 camera2.portability.force_api=1 persist.tegra.nvmmlite=1 persist.enable.3g.dongle=true testing.mediascanner.skiplist=/mnt/shell/emulated/Android/ keyguard.no_require_sim=true ExternalSD_ROOT=/mnt/external_sd InternalSD_ROOT=/mnt/internal_sd UserVolumeLabel=RockChip security.perf_harden=1 debug.nfc.se=false debug.nfc.fw_download=false debug.hwui.render_dirty_regions=false debug.atrace.tags.enableflags=0 net.bt.name=Android net.change=net.bt.name sys.hwc.enable=1 sys.hwc.compose_policy=6 sys.usb.controller=fe800000.dwc3 sys.rkadb.root=0 sys.status.hidebar_enable=false sys.wallpaper.rgb565=0 sys.resolution.changed=false persist.sys.ui.hw=true persist.sys.usb.config=mtp,adb persist.sys.boot.check=false persist.sys.media.avsync=true persist.sys.dalvik.vm.lib.2=libart.so persist.sys.country=PT persist.sys.language=pt persist.sys.timezone= persist.sys.strictmode.visual=false ro.ril.ecclist=112,911 ril.function.dataonly=1 sys.usb.config=adb sys.usb.configfs=1 Supported API: 3 I:Saving locale "en_US" [ 9.122706] fs_mgr: Warning: unknown flag resize Join led thread error! [ 13.614118] vop_isr: 285 callbacks suppressed [ 13.614193] rk322x-lcdc vop0: intr post buf empty! [ 13.614243] rk322x-lcdc vop0: intr post buf empty! [ 13.653464] rk322x-lcdc vop0: intr post buf empty! [ 13.653533] rk322x-lcdc vop0: intr post buf empty! [ 13.692821] rk322x-lcdc vop0: intr post buf empty! [ 13.692896] rk322x-lcdc vop0: intr post buf empty! [ 13.732183] rk322x-lcdc vop0: intr post buf empty! [ 13.732250] rk322x-lcdc vop0: intr post buf empty! [ 13.771542] rk322x-lcdc vop0: intr post buf empty! [ 13.771609] rk322x-lcdc vop0: intr post buf empty! [ 14.399515] [otg id chg] last id -1 current id 2 [ 18.573462] vop_isr: 281 callbacks suppressed [ 18.573520] rk322x-lcdc vop0: intr post buf empty! [ 18.573574] rk322x-lcdc vop0: intr post buf empty! [ 18.610020] read descriptors [ 18.610128] read descriptors [ 18.610169] read strings [ 18.610284] pcd_pullup, is_on 1 [ 18.612861] rk322x-lcdc vop0: intr post buf empty! [ 18.614549] init: write_file: Unable to write to '/config/usb_gadget/g1/UDC': No such device [ 18.652207] rk322x-lcdc vop0: intr post buf empty! [ 18.652303] rk322x-lcdc vop0: intr post buf empty! [ 18.691543] rk322x-lcdc vop0: intr post buf empty! [ 18.691617] rk322x-lcdc vop0: intr post buf empty! [ 18.730900] rk322x-lcdc vop0: intr post buf empty! [ 18.730971] rk322x-lcdc vop0: intr post buf empty! [ 18.770261] rk322x-lcdc vop0: intr post buf empty! [ 23.532823] vop_isr: 277 callbacks suppressed [ 23.532885] rk322x-lcdc vop0: intr post buf empty! [ 23.532942] rk322x-lcdc vop0: intr post buf empty! [ 23.572183] rk322x-lcdc vop0: intr post buf empty! [ 23.572253] rk322x-lcdc vop0: intr post buf empty! [ 23.611538] rk322x-lcdc vop0: intr post buf empty! [ 23.611605] rk322x-lcdc vop0: intr post buf empty! [ 23.650903] rk322x-lcdc vop0: intr post buf empty! [ 23.650970] rk322x-lcdc vop0: intr post buf empty! [ 23.690264] rk322x-lcdc vop0: intr post buf empty! [ 23.690331] rk322x-lcdc vop0: intr post buf empty! [ 28.492185] vop_isr: 268 callbacks suppressed [ 28.492244] rk322x-lcdc vop0: intr post buf empty! [ 28.492297] rk322x-lcdc vop0: intr post buf empty! [ 28.531544] rk322x-lcdc vop0: intr post buf empty! [ 28.531612] rk322x-lcdc vop0: intr post buf empty! [ 28.570905] rk322x-lcdc vop0: intr post buf empty! [ 28.570973] rk322x-lcdc vop0: intr post buf empty! [ 28.610263] rk322x-lcdc vop0: intr post buf empty! [ 28.610330] rk322x-lcdc vop0: intr post buf empty! [ 28.649619] rk322x-lcdc vop0: intr post buf empty! [ 28.649689] rk322x-lcdc vop0: intr post buf empty! [ 33.451540] vop_isr: 274 callbacks suppressed [ 33.451597] rk322x-lcdc vop0: intr post buf empty! [ 33.451648] rk322x-lcdc vop0: intr post buf empty! [ 33.490902] rk322x-lcdc vop0: intr post buf empty! [ 33.490973] rk322x-lcdc vop0: intr post buf empty! [ 33.530264] rk322x-lcdc vop0: intr post buf empty! [ 33.530331] rk322x-lcdc vop0: intr post buf empty! [ 33.569619] rk322x-lcdc vop0: intr post buf empty! [ 33.569692] rk322x-lcdc vop0: intr post buf empty! [ 33.608983] rk322x-lcdc vop0: intr post buf empty! [ 33.609050] rk322x-lcdc vop0: intr post buf empty! [ 38.410904] vop_isr: 281 callbacks suppressed [ 38.410961] rk322x-lcdc vop0: intr post buf empty! [ 38.411016] rk322x-lcdc vop0: intr post buf empty! [ 38.450262] rk322x-lcdc vop0: intr post buf empty! [ 38.450331] rk322x-lcdc vop0: intr post buf empty! [ 38.489619] rk322x-lcdc vop0: intr post buf empty! [ 38.489691] rk322x-lcdc vop0: intr post buf empty! [ 38.528982] rk322x-lcdc vop0: intr post buf empty! [ 38.529052] rk322x-lcdc vop0: intr post buf empty! [ 38.568343] rk322x-lcdc vop0: intr post buf empty! [ 38.568410] rk322x-lcdc vop0: intr post buf empty! [ 43.370262] vop_isr: 280 callbacks suppressed [ 43.370318] rk322x-lcdc vop0: intr post buf empty! [ 43.370370] rk322x-lcdc vop0: intr post buf empty! [ 43.409619] rk322x-lcdc vop0: intr post buf empty! [ 43.409691] rk322x-lcdc vop0: intr post buf empty! [ 43.448982] rk322x-lcdc vop0: intr post buf empty! [ 43.449051] rk322x-lcdc vop0: intr post buf empty! [ 43.488343] rk322x-lcdc vop0: intr post buf empty! [ 43.488411] rk322x-lcdc vop0: intr post buf empty! [ 43.527698] rk322x-lcdc vop0: intr post buf empty! where is the problem? Edited August 3, 2023 by n3o insert into spoliler section 0 Quote
jock Posted August 2, 2023 Author Posted August 2, 2023 @n3o please put the log in a spoiler section 0 Quote
sadp Posted August 3, 2023 Posted August 3, 2023 (edited) Ok guys, Hi. So I have managed to connect box Q96MAX 4k Ultra HD, board MXQ_R2B_LP3_V2.62_220225 via maskrom mode, made EMMC backup, erased it. btw thanks @MattWestB for your photos of pins https://github.com/MattWestb/R29-MXQ-LP3-V2.3-00908 Anyway, Box boots armbian legacy from SD card, I have managed to connect to it via SSH, device specs. Detected board features: │ │ Chip type: RK3228A/B - Serial: URKW46025 00000000032b0c │ │ CPU Leakage: 0x04 - Logic Leakage: 0x04 │ │ Internal flash: eMMC │ │ Wifi device: unknown - Device ID: 02d0:4334 EDIT2: installed RDP client, can connect to device via RDP...HDMI NO Output ok so thanks to this post https://github.com/MattWestb/R29-MXQ-LP3-V2.3-00908/blob/main/README.md armbian parameters set to emmc-hs200, ddr3-660 and led-config2, led started to work. @MattWestB can you please comment how you fixed your box HDMI and wifi?:) EDIT: ok so ARMBIAN non legacy boots too, but same problems with WIFI and HDMI no video. dmesg gives a lot of errors ... [ 0.003538] CPU: Testing write buffer coherency: ok [ 0.004292] /cpus/cpu@f00 missing clock-frequency property [ 0.004358] /cpus/cpu@f01 missing clock-frequency property [ 0.004391] /cpus/cpu@f02 missing clock-frequency property [ 0.004424] /cpus/cpu@f03 missing clock-frequency property [ 0.004446] CPU0: thread -1, cpu 0, socket 15, mpidr 80000f00 ... [ 2.029717] inno-hdmi-phy 12030000.hdmi-phy: error -ENXIO: IRQ index 0 not found [ 2.030102] inno-hdmi-phy 12030000.hdmi-phy: phy_flag is: 0 [ 2.033084] rockchip-drm display-subsystem: bound 20050000.vop (ops 0xb127c87c) [ 2.033274] dwhdmi-rockchip 200a0000.hdmi: supply avdd-0v9 not found, using dummy regulator [ 2.033657] mmc_host mmc2: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) [ 2.033677] dwhdmi-rockchip 200a0000.hdmi: supply avdd-1v8 not found, using dummy regulator [ 2.034239] dwhdmi-rockchip 200a0000.hdmi: Detected HDMI TX controller v2.01a with HDCP (inno_dw_hdmi_phy2) [ 2.035607] mmc2: new high speed MMC card at address 0001 [ 2.035736] dwhdmi-rockchip 200a0000.hdmi: registered DesignWare HDMI I2C bus driver [ 2.037470] mmcblk2: mmc2:0001 Q2J95T 7.28 GiB [ 2.039082] rockchip-drm display-subsystem: bound 200a0000.hdmi (ops 0xb1280568) ... [ 3.603319] rockchip-pinctrl pinctrl: unable to find group for node reset-key ... [ 15.966192] brcmfmac: brcmf_fw_alloc_request: Unknown chip BCM43342/0 ... [ 16.859644] systemd[1]: Starting Armbian memory supported logging... [ 17.040253] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): clkctl 0x50 [ 17.091210] systemd[1]: Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch. [ 17.099828] brcmfmac: brcmf_ops_sdio_probe: F2 error, probe failed -19... [ 17.144754] systemd[1]: Finished Raise network interfaces. ... [ 45.622143] hdmi-audio-codec hdmi-audio-codec.2.auto: Only one simultaneous stream supported! [ 45.652339] hdmi-audio-codec hdmi-audio-codec.2.auto: ASoC: error at snd_soc_dai_startup on i2s-hifi: -22 [ 45.676365] 100c0000.i2s0-i2s-hifi: ASoC: error at __soc_pcm_open on 100c0000.i2s0-i2s-hifi: -22 ... i attach log here pls help with wifi/hdmi dmesg.log Edited August 3, 2023 by sadp 2 Quote
n3o Posted August 3, 2023 Posted August 3, 2023 11 hours ago, jock said: @n3o please put the log in a spoiler section done... what can You tell me about the issue? 0 Quote
jock Posted August 3, 2023 Author Posted August 3, 2023 @sadp Your wifi chip is not supported by the brcmfmac driver; there is a patch for rockchip64 family but not for rk322x. I will make a Pull Request to add the patch for rk322x but have to be patient, wait a couple of weeks and it will be probably available for edge 6.4 kernel. You are on current 6.1 right now, so perhaps you may want to switch when the new kernel will be available. About the missing HDMI, it is a known problem for all R29 boards; @Hudson FAS gently offered to send me a board of such kind for me to inspect and try to fix the issue, so patience here too. 1 Quote
jock Posted August 3, 2023 Author Posted August 3, 2023 5 hours ago, n3o said: done... what can You tell me about the issue? Actually I don't remember your issue (the last post was 3 months ago), but I see @RaptorSDS was already in contact with you. 0 Quote
n3o Posted August 3, 2023 Posted August 3, 2023 45 minutes ago, jock said: Actually I don't remember your issue (the last post was 3 months ago), but I see @RaptorSDS was already in contact with you. device no more boot and load into recovery mode 0 Quote
RaptorSDS Posted August 3, 2023 Posted August 3, 2023 vor 18 Stunden schrieb n3o: [ 8.215212] init: property_set("ro.hardware", "rk30board") failed [ 8.223761] init: Running restorecon... [ 8.288108] vendor storage:20160801 ret = -1 [ 8.312205] init: waitpid failed: No child processes [ 8.313478] init: property_set("ro.board.platform", "rk322x") failed looks like android has many false setting or broke 0 Quote
sadp Posted August 3, 2023 Posted August 3, 2023 @jock thanks for your hard work and for your reply, I understand, waiting for possible fixes 0 Quote
n3o Posted August 3, 2023 Posted August 3, 2023 8 minutes ago, RaptorSDS said: looks like android has many false setting or broke ok, I want install armbian but also multiboot doesn't worked very well... what step I should do? I think that is unuseful make a backup of a Android system damaged, so how I can make the bootloader upgrade described here https://forum.armbian.com/topic/12656-csc-armbian-for-rk322x-tv-boxes/?do=findComment&comment=121103 ? 2. For the bootloader file, I have a file named rk322x_loader_v1.10.256.bin but I don't remember where I have download it, can You tell me if I should download the updated file from here https://github.com/ilmich/rkflashtool/tree/master/bin ? and what file ? ? 3. After this, in first post isn't explained difference between images here https://imola.armbian.com/dl/rk322x-box/archive/ , so what is the difference between bookworm and jammy? and what are the differences between <<standard (without nothing added)>>, xfce, minimal and wm? It's explained only current, edge and legacy 0 Quote
RaptorSDS Posted August 3, 2023 Posted August 3, 2023 vor 30 Minuten schrieb n3o: ok, I want install armbian but also multiboot doesn't worked very well but now you can see why it is not work , and also interact with armbian without HDMI if HDMI doesnt work 0 Quote
fabiobassa Posted August 3, 2023 Posted August 3, 2023 @n3o Quote so what is the difference between bookworm and jammy? migh tI ask you how much skill have you not only on linux but in general on pc's ? Quote ok, I want install armbian but also multiboot doesn't worked very well. What EXACTLY you mean by this ? 0 Quote
RaptorSDS Posted August 3, 2023 Posted August 3, 2023 vor 59 Minuten schrieb n3o: bookworm and jammy bookworm is Debian 12 jammy is Ubuntu 22.04 0 Quote
ego worker Posted August 3, 2023 Posted August 3, 2023 (edited) Hi, got the same board as TV box different brand: MXQ PRO 4K 5G Bought recently, so probably all got the same board MultiTool works fine, can flash and erase via SSH Problem is that no image for rk322x box works, no working HDMI. Only when I boot it with LAN plugged in - yellow Led blinks - but no IP is assigned. Edit: Or it does work but there is no SSH enabled in armbian ? I dont rly need HDMI and GPU at all, just wonna reach ssh it doesnt get IP from DHCP ... dmesg.multitool.log Edited August 3, 2023 by ego worker 0 Quote
n3o Posted August 3, 2023 Posted August 3, 2023 3 hours ago, RaptorSDS said: but now you can see why it is not work , and also interact with armbian without HDMI if HDMI doesnt work how can I make this? In putty the last lines automatically appear, it's not SSH. What should I do ? Can You tell me from the log posted what bootloader file flash? 2 hours ago, fabiobassa said: migh tI ask you how much skill have you not only on linux but in general on pc's ? I'm a java developer, sadly not always it's possible found a complete course from A to Z (for example, in linux, a course that cover vmlinuz, disk partition, boot (bios and uefi), virtual machine, dsa network config, ecc ecc) ... so I have fragmentated concepts ... to this add that I'm not a system administrator so it's easy forgotten also the basis. In electronic instead I don't know nothing (this is related to the UART problem). 2 hours ago, RaptorSDS said: bookworm is Debian 12 jammy is Ubuntu 22.04 what do You recommend me? and what about <<standard (without nothing added)>>, xfce, minimal and wm ? 0 Quote
RaptorSDS Posted August 3, 2023 Posted August 3, 2023 vor 2 Minuten schrieb n3o: it's not SSH its better its a serial console , you can interact with linux over tty Serial connect (you have with this now with UART) , when multitool is running like in a ssh session ssh is a forwarde serial console over ip (more or less) when you run headless ( without gui) linux do the same a serial console is than also forwarde to HDMI (more or less) vor 5 Minuten schrieb n3o: what do You recommend me? both have same source , both use same tools and programm Debian has philosophy "no close source" but your are able to install them when need Ubuntu is from start with close source software but that makes its sometime bigger and more complex both can use xcfe and other gui ( some of the image files already have xfce active) , when you only need server go with minimal 0 Quote
n3o Posted August 3, 2023 Posted August 3, 2023 5 minutes ago, RaptorSDS said: its better its a serial console , you can interact with linux over tty Serial connect (you have with this now with UART) , when multitool is running like in a ssh session ssh is a forwarde serial console over ip (more or less) when you run headless ( without gui) linux do the same a serial console is than also forwarde to HDMI (more or less) so I should just insert microsd with multitool and I can start procedure of @jock ? What bootloader file should I load? in the first post, at section "Quick installation instructions on NAND" at point 2 is written "Burn the Multitool on an SD card; once done, place the Armbian legacy kernel image in images folder of the SD card FAT partition"... it's possible use only legacy kernel? 2 hours ago, RaptorSDS said: both have same source , both use same tools and programm Debian has philosophy "no close source" but your are able to install them when need Ubuntu is from start with close source software but that makes its sometime bigger and more complex both can use xcfe and other gui ( some of the image files already have xfce active) , when you only need server go with minimal ok, I'll try bookworm 0 Quote
ego worker Posted August 4, 2023 Posted August 4, 2023 (edited) Ok, I have atached to UART, and looks like armbian boots but no HDMI, no IP from LAN edit: Ok Lan and SSH started to work after first login nice any solution for not working HDMI ? edit2: Legacy 4.4 works (noHDMI), mainline doesnt, kernel panic (currentkernel.txt) Booting Linux.txt CurrentKernel.txt Edited August 4, 2023 by ego worker 0 Quote
n3o Posted August 4, 2023 Posted August 4, 2023 16 hours ago, n3o said: so I should just insert microsd with multitool and I can start procedure of @jock ? What bootloader file should I load? in the first post, at section "Quick installation instructions on NAND" at point 2 is written "Burn the Multitool on an SD card; once done, place the Armbian legacy kernel image in images folder of the SD card FAT partition"... it's possible use only legacy kernel? @RaptorSDS can You help me? 0 Quote
RaptorSDS Posted August 4, 2023 Posted August 4, 2023 vor 29 Minuten schrieb n3o: it's possible use only legacy kernel? i can not hep by flash any other bootloader or make nand work with newer kernel , i dont understand why only kernel that make no sense , flash legay armbian and go on with the box , else put legacy image on the box and than show the log we can look why maybe the box dont boot full to armbian you can save also android because maybe we need dts/dtb or anything else and extract it out of image file 0 Quote
ego worker Posted August 4, 2023 Posted August 4, 2023 (edited) Colected info of this board https://github.com/kenavru/rk3228_TVBox atempting to recover dtb from android ... but cant find it 😆 https://raw.githubusercontent.com/kenavru/rk3228_TVBox/main/binwalk_android_emmc.txt is it somewhere else than backup possible from multitool ? Edited August 4, 2023 by ego worker 0 Quote
n3o Posted August 4, 2023 Posted August 4, 2023 1 hour ago, RaptorSDS said: i can not hep by flash any other bootloader or make nand work with newer kernel , i dont understand why only kernel that make no sense , flash legay armbian and go on with the box , else put legacy image on the box and than show the log What do You mean for "i dont understand why only kernel that make no sense" ? here https://imola.armbian.com/dl/rk322x-box/archive/ there are only current version, so where are the legacy images? 1 hour ago, RaptorSDS said: we can look why maybe the box dont boot full to armbian actually the box don't boot to stock android and I'm searching what image load 1 hour ago, RaptorSDS said: you can save also android because maybe we need dts/dtb or anything else and extract it out of image you mean load android image? what are dts/dtb ? 0 Quote
ego worker Posted August 4, 2023 Posted August 4, 2023 (edited) https://armbian.hosthatch.com/archive/rk322x-box/archive/ here are legacy c.d. I have extracted 4 dtb files, 3 looks fine, all references to rk3229, none is able to run Multitool ;( Edited August 4, 2023 by ego worker 0 Quote
RaptorSDS Posted August 4, 2023 Posted August 4, 2023 please guys dont mix topix thanks @ego worker for post link @n3o vor 19 Stunden schrieb n3o: t's possible use only legacy kernel? that why i was wonder , kernel is a part of linux but some like Android sometime have that as a seperate partion or like rasberry you can update kernel only also you talk about bootloader upgrade and i am was confuse about what you want and your knowloge about flashing this box with linux vor 1 Stunde schrieb n3o: you mean load android image? what are dts/dtb ? no save android dts/dtb are config file for kernel--> tell kernel where to look at for lan or wich memory or clock to use for hdmi and so on i thinks easy step are on page 1 when your box is nand than follow the step with a legacy armbian image and have fun with this box 0 Quote
MattWestB Posted August 5, 2023 Posted August 5, 2023 @sadp I using my box headless and by not connecting the HDMI its not running so warm (i doing the same with my RK3318 box that is having HDMI working OK last time i was looking) and i using local comport for the initial config and then SSH so no need for desktop for my. Also i running Zigbee and Thred RCP and WiFi is only making problems so i only using Eth for not getting interference with my 802.15.4 mesh networks. Only real problems beside the box is very easy running hot is that the USB implementation is nerving if one device is having problems and the system is disconnecting it the system must being repowered for the system finding it and its the same for the RK3318 box so its one RK thing that is not working very well. My firs problem was that the box was not liking the bootloader but i was finding one working one and flashing it to the eMCC and after that i have no problem installing armbian on the internal storage and can booting SD and USB storage for testing other armbian builds so its very good only the box is only having 8G internal flash so i have mounting the SD-card as docker data so HA supervised have enough storage for installing and working OK. 0 Quote
n3o Posted August 5, 2023 Posted August 5, 2023 On 8/4/2023 at 6:31 PM, ego worker said: https://armbian.hosthatch.com/archive/rk322x-box/archive/ here are legacy c.d. I have extracted 4 dtb files, 3 looks fine, all references to rk3229, none is able to run Multitool ;( so, it's impossible update bootloader? 23 hours ago, RaptorSDS said: that why i was wonder , kernel is a part of linux but some like Android sometime have that as a seperate partion or like rasberry you can update kernel only also you talk about bootloader upgrade and i am was confuse about what you want and your knowloge about flashing this box with linux I want install the most recent image of armbian with gui (so I don't want android) and in first post is written that it's necessary update bootloader "For fearless and bold people who are having issues when (re)booting images, there is the chance to upgrade the bootloader on NAND". So I prefer update bootloader and after that install the most recent image. For the bootloader I should use one of the 2 files here https://github.com/ilmich/rkflashtool/tree/master/bin but now reading the steps on the first post I have discovered that only legacy armbian image can be used. Now, the new question is: what is the difference between bullseye and jammy? Jammy isn't available with gui? I'm not very expert about linux and flashing, I know only that bootloader is such a bios ... 23 hours ago, RaptorSDS said: no save android dts/dtb are config file for kernel--> tell kernel where to look at for lan or wich memory or clock to use for hdmi and so on ok, where I can find this file (and how to reach destination if android no more boot)? What is the path? When I install the armbian image to make restore I have just copy and paste the files? 0 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.