All Activity

@VanGeldon Seems like an old image: try one from here: https://imola.armbian.com/dl/orangepi5/archive/ When you choose an image with amazingfated and Wayland like Gnome or KDE you probably only need to install Kodi.

Try this https://launchpad.net/~savoury1

Hi Thomas, thanks for your report - I was thinking about a cronjob too o something that monitors dmesg nevertheless, as a mitigation to avoid a reboot when wifi stops I can suggest: sudo rmmod sprdwl_ng && sudo modprobe sprdwl_ng Definitely not elegant, but gets wifi back from the dead until the next band hop Hope it helps Ale

@kuber gld This might be the answer

Following initial steps with Armbian_23.8.1_Orangepi5_jammy_legacy_5.10.160_xfce_desktop at sudo apt install ubuntu-desktop kodi receiving The following packages have unmet dependencies: gjs : Depends: libgjs0g (= 1.72.2-0ubuntu2) but 1.72.4-0ubuntu0.22.04.1 is to be installed E: Unable to correct problems, you have held broken packages.

Yes, the cpu temperature is about 40 °C.

lsusb should display USB devices.

Are you using proper cooling?

Plug in another usb-serial device, see what happens in that case

I tried another version: armbian_23.02.0-runk_Onecloud_jammy_edge_6.1.9_minimal.burn.img It shutdown about every 10 minutes. log uploaded here: https://paste.armbian.com/reseqowita armbian-hardware-monitor.log dmesg.0 kern.log 23.02.0-shutdown-every-10-minutes.txt

@martivo are you using beta or stable?

Description Use radxa's next-dev-v2024.03 branch for armsom's boards. Note that I have to remove CONFIG_OPTEE_ALWAYS_USE_SECURITY_PARTITION=y from defconfig to boot the board. So boards affected by https://github.com/armbian/build/pull/6534 like nanopi6 and nanopc-t6 should also check this. @efectn @Tonymac32 How Has This Been Tested? Please describe the tests that you ran to verify your changes. Please also note any relevant details for your test configuration. [x] ./compile.sh BOARD=armsom-sige7 BRANCH=vendor BUILD_DESKTOP=no BUILD_MINIMAL=no DEB_COMPRESS=xz KERNEL_CONFIGURE=no RELEASE=bookworm KERNEL_GIT=shallow Checklist: Please delete options that are not relevant. [x] My code follows the style guidelines of this project [x] I have performed a self-review of my own code [ ] I have commented my code, particularly in hard-to-understand areas [x] My changes generate no new warnings [ ] Any dependent changes have been merged and published in downstream modules View the full article

Yes. I have krescue. It still hasn't worked. I have a vim3 from a year ago that I have manjaro booting from sdcard. I'd like it to be armbian, but havent managed to get an armbian sdcard to boot in it. Its my only working vim3. I bought a Vim4 recently. But it was DOA. Now I'm travelling and have no recourse but to keep using manjaro which Kind-of sucks. I left the android only vim3 at home.

Here is the most recent thread on s805:

There are is no Armbian support for s805 based tv boxes (only s905 based boxes).

Post of NicoD

Hello, I'm new to this forum here. I don't know if it have solution to boot flashed USB (NOT SD-Card) contain Armbian OS from Recovery Mode on cheap Android TV Boxes (Set-top) ? Because I have this box with model `SB801` (Device name: Acnos SB801 [from Vietnam] ) doesn't have SD-Card slot but it has specs like Odroid C1 / MXQ / Mbox SB801. Little specs preview: + CPU: Amlogic S805 + RAM/ROM: 1GB/8GB + Running OS: Android 4.0 + USB Slot: 2 + Display connector: HDMI, [? Red,White,Yellow] + Network: Ethernet, Wi-Fi Thanks. **sorry for my bad English

@A J I'm not sure which image you have burned, but most images do not have a separate boot partition, they just have one ext4 partition that contains everything. Images that have a separate /boot partition do that either because of limitations of the u-boot version being used, or because they want to provide easier access to the /boot via a non linux platform (i.e. windows) for accessing the contents of that partition.

Hello there! I want to ask a question about burning images into SD cards. I followed the steps of OP, I tried to burn the image via DD and via balenaEtcher, and both of them didn't created a boot partition (balenaEtcher did warn me that the image does not contain a partition table). As far as I recall, those files like uEnv.txt, .dtb, etc must be placed in the boot partition, am I right? Did I do something wrong, or did I should somehow create those parts by myself? Thanks!

Sorry, appears to be working good. My bad wrong governor selected.

I run output/images/Armbian-unofficial_24.5.0-trunk_Onecloud_bookworm_current_6.6.21_minimal.burn.img on my onecloud board. It shutdown about every 40 minutes. How to solve this problem? Thanks! journalctl.log kern.log armbian-hardware-monitor.log

Libre Renegade overlays opp-1.4ghz and opp-1.5ghz load but not working in trixie edge (24.5.0-trunk.512). Both overlays do work in 24.2.1 bookworm.