Jokr_Kedo Posted December 11, 2020 Share Posted December 11, 2020 Red light on boot and Can't detect via putty serial. But, OPi3 works ok on ubuntu 16.8(green light). Any sollution???? Board: Not on the list Link to comment Share on other sites More sharing options...
Igor Posted December 11, 2020 Share Posted December 11, 2020 3 hours ago, Jokr_Kedo said: Any sollution???? We already wasted hundred + hours of our precious private time on this bug but we don't have a solution yet: https://github.com/armbian/build/issues/2315 1 Link to comment Share on other sites More sharing options...
dolphs Posted December 13, 2020 Share Posted December 13, 2020 looks like 5.9 images are being published as recommended, therefore suppose fix/workaround is in place ? That would be very nice! Link to comment Share on other sites More sharing options...
Werner Posted December 13, 2020 Share Posted December 13, 2020 Unfortunately no. Could not be solved yet. I tried do dig a bit deeper and found some things that could be tried but I do not have this board myself and other H6 board seem unaffected so I cannot test. Link to comment Share on other sites More sharing options...
dolphs Posted December 13, 2020 Share Posted December 13, 2020 my spare OpiOnePlus has been upgraded , dont have Opi3 either. Anyway to see if the OPiOnePlus is unaffected will reboot few times today and see if it comes back online normally .... Link to comment Share on other sites More sharing options...
Jokr_Kedo Posted December 13, 2020 Author Share Posted December 13, 2020 5 minutes ago, dolphs said: my spare OpiOnePlus has been upgraded , dont have Opi3 either. Anyway to see if the OPiOnePlus is unaffected will reboot few times today and see if it comes back online normally .... Ok. Link to comment Share on other sites More sharing options...
dolphs Posted December 13, 2020 Share Posted December 13, 2020 done a few more ( approx 6 ) till now and all looking good, will start with cold boot early morning to see how things go and give a few more reboots after that. but seems to be fine on this H6 board, over to topic : OrangePi3 [EDIT] Meanswhile executed reboots and cold starts, OPiOnePlus came back OK all the time ( kernel 5.9.16 ) [/EDIT] Link to comment Share on other sites More sharing options...
markonjak Posted December 15, 2020 Share Posted December 15, 2020 Suddenly my ethernet stopped working, i didn't touch anything, just updated, upgraded and rebooted, the cable is ok i tested it on my pc and the ethernet works, also ethtool says the link is up and detected, i have no idea what's the problem?, any help, also set static ip 2 weeks ago worked fine until now, also the lights on the ethernet port are lighting, the orange is constantly lit and the green occasionally flashes, orangepi3, the log is too long, putty doesn't save enough of it Link to comment Share on other sites More sharing options...
Zygmunt Zarzecki Posted December 17, 2020 Share Posted December 17, 2020 On 12/15/2020 at 11:12 PM, markonjak said: Suddenly my ethernet stopped working, i didn't touch anything, just updated, upgraded and rebooted, the cable is ok i tested it on my pc and the ethernet works, also ethtool says the link is up and detected, i have no idea what's the problem?, any help, also set static ip 2 weeks ago worked fine until now, also the lights on the ethernet port are lighting, the orange is constantly lit and the green occasionally flashes, orangepi3, the log is too long, putty doesn't save enough of it I have the same issue. Link is up, but networking is down. Everything in configuration is ok. Link to comment Share on other sites More sharing options...
Werner Posted December 17, 2020 Share Posted December 17, 2020 https://github.com/armbian/build/issues/2315 Getting closer Link to comment Share on other sites More sharing options...
markonjak Posted December 18, 2020 Share Posted December 18, 2020 I think the problem is in the latest kernel, i switched to an older kernel 5.8.16-sunxi64, and now ethernet works without a problem and everything else. Link to comment Share on other sites More sharing options...
5kft Posted December 18, 2020 Share Posted December 18, 2020 This problem sounds like this issue: https://github.com/armbian/build/issues/2315 1 Link to comment Share on other sites More sharing options...
channel999 Posted December 19, 2020 Share Posted December 19, 2020 The mistake also occurs with me. (Orange Pi 3). Has already cost me a day of misalignment. Always after upgrading, the Ethernet is dead. A current image (Armbian_20.11.3_Orangepi3_buster_current_5.9.14) freshly flashed cannot also be achieved via SSH. Link to comment Share on other sites More sharing options...
Igor Posted December 19, 2020 Share Posted December 19, 2020 1 hour ago, channel999 said: Has already cost me a day of misalignment. We already lost weeks just on this problem. Thank you for covering our time! Link to comment Share on other sites More sharing options...
Zygmunt Zarzecki Posted December 20, 2020 Share Posted December 20, 2020 On 12/17/2020 at 1:21 PM, Zygmunt Zarzecki said: I have the same issue. Link is up, but networking is down. Everything in configuration is ok. Armbian_21.02.0-trunk.28_Orangepi3_focal_current_5.9.15.img have the same issue. Link to comment Share on other sites More sharing options...
Werner Posted December 20, 2020 Share Posted December 20, 2020 I merged both topics since they cover the same issue. Quick summary: Issue is discovered but solution could be difficult. Downgrade to 5.8 kernel for now. Link to comment Share on other sites More sharing options...
markonjak Posted December 20, 2020 Share Posted December 20, 2020 11 hours ago, Igor said: We already lost weeks just on this problem. Thank you for covering our time! I appreciate all the work and time you put into this, do you know what's the problem or still investigating? Link to comment Share on other sites More sharing options...
Werner Posted December 20, 2020 Share Posted December 20, 2020 48 minutes ago, markonjak said: do you know what's the problem or still investigating? Link to comment Share on other sites More sharing options...
channel999 Posted December 21, 2020 Share Posted December 21, 2020 Hello. @ Igor I'm sorry if I wasted your time with my first post. That wasn't my intention. I have great respect for the work you are doing here and I am very grateful for that. I can already find out from the article that there is a problem in the kernel so far. I just wanted to confirm that my Orange Pi 3 is the same. That may have been stupid of me. I'm sorry. @ Werner Thank you for the info! I'm switching back to a system with kernel level 5.8, and I'm waiting for development. 2 Link to comment Share on other sites More sharing options...
Recommended Posts