LarryM Posted October 13, 2017 Share Posted October 13, 2017 I'm not sure what you're asking, I'm assuming you want me to reboot with the KVM plugged into LePotato, then ssh into it from another PC, and run that command? I didn't get the part about "or use the uart" FYI, if I run it now (with the KVM plugged in and working) I get /var/log/armhwinfo.log had been uploaded to http://sprunge.us/fjQM I assume there's no cut-n-paste in this terminal emulator? Link to comment Share on other sites More sharing options...
TonyMac32 Posted October 14, 2017 Share Posted October 14, 2017 I was pointing out you could use the serial port if you couldnt for some reason ssh. Thank you for the info, I'll look over it. I use Putty from a windows machine, it allows copying/pasting. Link to comment Share on other sites More sharing options...
Bret Barnes Posted October 14, 2017 Share Posted October 14, 2017 I just fired up the 171014 desktop nightly. No video on a DVI monitor even when I unplug replug. The c2_init.sh isn't helping either. Worked on the 171013 one. Is that because this one is 4.13 instead of 3.14? I notice it's doing the blue light heartbeat too. Link to comment Share on other sites More sharing options...
TonyMac32 Posted October 14, 2017 Share Posted October 14, 2017 Let me take a look. Can you SSH into the board or use the serial port to grab the debug info from executing armbianmonitor -u while I download the image in question and test? Link to comment Share on other sites More sharing options...
Bret Barnes Posted October 14, 2017 Share Posted October 14, 2017 http://sprunge.us/XGKN Link to comment Share on other sites More sharing options...
TonyMac32 Posted October 14, 2017 Share Posted October 14, 2017 Strange, quick look and I didn't see anything. Do you have another monitor to try, I just booted that image without issue, going through the initial login now. [edit] Power cycling still yields a working desktop, my dmesg and lsmod match yours. Link to comment Share on other sites More sharing options...
Bret Barnes Posted October 14, 2017 Share Posted October 14, 2017 Tried two more. the 1600x1200 gave me "this mode can't be displayed" for a sec. And went to sleep. 1680x1050 just went into power saving. Not a flicker not a flash. Replugging had no effect. Link to comment Share on other sites More sharing options...
Bret Barnes Posted October 14, 2017 Share Posted October 14, 2017 When I get the chance I'll see if I can find some other to try tomorrow. There has to be some kind of difference that can be pegged down. Link to comment Share on other sites More sharing options...
TonyMac32 Posted October 14, 2017 Share Posted October 14, 2017 Please share the results of: export XAUTHORITY=/home/$USER/.Xauthority export DISPLAY=:0 xrandr The output of mine for example: Monitor 1 plugged in: root@lepotato:~# xrandr Screen 0: minimum 320 x 200, current 1920 x 1080, maximum 3840 x 2160 Composite-1 connected (normal left inverted right x axis y axis) 720x576i 50.00 720x480i 59.94 HDMI-1 connected 1920x1080+0+0 (normal left inverted right x axis y axis) 477mm x 268mm 1920x1080 60.00*+ 1280x720 60.00 -------------------------------------------------------------------------------------------- Monitor 2 plugged in: root@lepotato:~# xrandr Screen 0: minimum 320 x 200, current 1920 x 1080, maximum 3840 x 2160 Composite-1 connected (normal left inverted right x axis y axis) 720x576i 50.00 720x480i 59.94 HDMI-1 connected 1920x1080+0+0 (normal left inverted right x axis y axis) 608mm x 345mm 1920x1080 60.00* 50.00 30.00 24.00 1280x720 60.00 50.00 720x576 50.00 720x480 59.94 Link to comment Share on other sites More sharing options...
Bret Barnes Posted October 14, 2017 Share Posted October 14, 2017 On two monitors I got this exactly. Replugging and rerunning the exports and xrandr produced the same also. The both work fine for everything else also and I use that same hdmi to dvi cable for my RPi 3. root@lepotato:~# xrandr xrandr: Output HDMI-1 is not disconnected but has no modes Screen 0: minimum 320 x 200, current 720 x 576, maximum 3840 x 2160 Composite-1 connected 720x576+0+0 (normal left inverted right x axis y axis) 0mm x 0mm 720x576i 50.00* 720x480i 59.94 HDMI-1 connected (normal left inverted right x axis y axis) root@lepotato:~# Link to comment Share on other sites More sharing options...
TonyMac32 Posted October 14, 2017 Share Posted October 14, 2017 Interesting. You only have to do the export once in a session, it's so you can reference the displays via the console. My "monitor 1" is an hdmi --> DVI adapter on the end of an hdmi cable, so unless the cables are strange I'm not sure. Link to comment Share on other sites More sharing options...
TonyMac32 Posted October 16, 2017 Share Posted October 16, 2017 The Arm Trusted Firmware memory issue will not be fixed in the 4.14 LTS kernel, which is a bit curious, it's a pretty significant flaw and renders the Meson-GXL family of boards to be little more than paperweights. I glazed over the bit where it's queued for 4.15. Glad I didn't hold off patching Dev. @balbes150 might be interested in this as well. It's a small patch, so not a terrible tragedy, unless you don't know it exists... 1 Link to comment Share on other sites More sharing options...
jeky82 Posted October 23, 2017 Share Posted October 23, 2017 Hi, is there someone to get audio output from the jack instead of hdmi? Link to comment Share on other sites More sharing options...
Tido Posted November 25, 2017 Share Posted November 25, 2017 (edited) While doing testing I came across a weird behavior: it will shutdown with the command: halt , but it will reboot with "init 0" Welcome to ARMBIAN 5.34.171104 nightly Ubuntu 16.04.3 LTS 4.13.11-meson64 I think here it still worked as it should, but since I updated to: Welcome to ARMBIAN 5.34.171121 nightly Ubuntu 16.04.3 LTS 4.13.14-meson64 And also a fresh install apt update /upgrade it will reboot with: init 0 Welcome to ARMBIAN 5.35 user-built Debian GNU/Linux 9 (stretch) 4.14.2-meson64 System diagnosis information will now be uploaded to http://sprunge.us/DXjB Please post the URL in the forum where you've been asked for. This was only visible via UART Spoiler [ OK ] Stopped target Encrypted Volumes. [ OK ] Stopped Forward Password Requests to Wall Directory Watch. [ OK ] Stopped Dispatch Password Requests to Console Directory Watch. [ OK ] Stopped Load/Save Random Seed. [ OK ] Stopped Restore / save the current clock. [ OK ] Stopped Update UTMP about System Boot/Shutdown. [ OK ] Stopped Create Volatile Files and Directories. [ OK ] Unmounted /var/log. [ OK ] Deactivated swap /var/swap. [ OK ] Unmounted /var/log.hdd. [ OK ] Stopped Armbian enhanced Log2Ram. [ OK ] Stopped ifup for eth0. [ OK ] Stopped target Local File Systems. Unmounting /run/user/0... Unmounting /tmp... [ OK ] Stopped Apply Kernel Variables. [ OK ] Stopped Load Kernel Modules. [ OK ] Unmounted /run/user/0. [ OK ] Unmounted /tmp. [ OK ] Reached target Unmount All Filesystems. [ OK ] Stopped target Local File Systems (Pre). [ OK ] Stopped Remount Root and Kernel File Systems. [ OK ] Stopped Create Static Device Nodes in /dev. [ OK ] Reached target Shutdown. [ 234.817510] reboot: Power down bl31 reboot reason: 0x8 bl31 reboot reason: 0x8 system cmd 0. bl30 get wakeup sources! with the halt command: Spoiler [ OK ] Stopped target Encrypted Volumes. [ OK ] Stopped Dispatch Password Requests to Console Directory Watch. [ OK ] Stopped Forward Password Requests to Wall Directory Watch. Stopping Restore / save the current clock... [ OK ] Stopped target Swap. Deactivating swap /var/swap... Stopping Update UTMP about System Boot/Shutdown... Stopping Armbian enhanced Log2Ram... [ OK ] Stopped Load/Save Random Seed. [ OK ] Stopped Restore / save the current clock. [ OK ] Deactivated swap /var/swap. [ OK ] Stopped Update UTMP about System Boot/Shutdown. [ OK ] Stopped Create Volatile Files and Directories. [ OK ] Unmounted /var/log. [ OK ] Unmounted /var/log.hdd. [ OK ] Stopped Armbian enhanced Log2Ram. [ OK ] Stopped ifup for eth0. [ OK ] Stopped Apply Kernel Variables. [ OK ] Stopped Load Kernel Modules. [ OK ] Stopped target Local File Systems. Unmounting /tmp... Unmounting /run/user/0... [ OK ] Unmounted /tmp. [ OK ] Unmounted /run/user/0. [ OK ] Reached target Unmount All Filesystems. [ OK ] Stopped target Local File Systems (Pre). [ OK ] Stopped Create Static Device Nodes in /dev. [ OK ] Stopped Remount Root and Kernel File Systems. [ OK ] Reached target Shutdown. [ 203.685417] reboot: System halted The red LED does not go off. Edited November 25, 2017 by Tido added codebox Link to comment Share on other sites More sharing options...
TonyMac32 Posted November 25, 2017 Share Posted November 25, 2017 To my knowledge this has always been the case. I'm looking into whether or not this is bootloader related I think the C2 was doing something similar?, as for the light: The Red LED does not appear to be software controlled from the schematics. DC-in goes through what I think is a reverse voltage/backfeed protection circuit and then through a step-down to 3.3V feeding the diode. No software intervention. Link to comment Share on other sites More sharing options...
Tido Posted November 26, 2017 Share Posted November 26, 2017 15 hours ago, TonyMac32 said: whether or not this is bootloader related Interesting, I thought technically 'halt' vs 'init 0' vs 'shutdown -P now' are equal. 15 hours ago, TonyMac32 said: No software intervention U6 SY8120B1ABC --> VDDIO_AO3.3V --> red LED --> 240 Ohm --> GND on schematics page 3 down right corner. Whereas green (GPIODV_24(PU)) and blue (GPIO15) have a transistor in between. I have removed the SDcard and powered it. The blue and the red lit up - why the blue? blue LED GPIO15: SoC --> GPIOAO_2 (UART_CTS_AO_A // UART_CTS_AO_B) 40Pin Connector--> I2SOUT-CH67 Link to comment Share on other sites More sharing options...
Tido Posted December 12, 2017 Share Posted December 12, 2017 After seeing your changes I thought I give it an update, followed by init 6, reboot works, followed by init 0 ... hmmm LEDs still as bright as it gets .. is this an error... ah no, I try halt. That worked. Init 0: [ 234.817510] reboot: Power down (and then it reboots) halt: [ 203.685417] reboot: System halted (properly shuts down) Init is the runlevel, does this finally trigger the 'halt' command ? https://unix.stackexchange.com/a/8694 Link to comment Share on other sites More sharing options...
richard1937 Posted March 15, 2018 Share Posted March 15, 2018 My comments here is from real frustration, SO PLEASE excuse my being very direct. I have several RPi 3's 2 Asus TinkerPi. and several OrangePi 2 plus. and now also the LePotato. I do really appreciate the work folk working on OS's for these, It is indeed a lot of really great work, especially with the very flakey OrangePi's , power supply issues etc etc. Ok, NOW for give me for this. I started with RPi's , they boot to an initial screen that has "boarder" and have you setup to be compatible relative to overscan - Monitor/HDMI As I am sure YOU ALL are aware. IF this is NOT first addressed. that which is to be displayed is off the left side of the screen. Most, in-fact all of the monitors I own do NOT have and adjustment/setting to change the overscan settings. I have a several large screen TV's which do let you change this attribute. But connecting my wall mounted 55" TV is not very practical. Yes, I am aware of xrandr. EDID, h3disp etc. etc. and I have ended up wading through trying to change one of these once I finally get in inspite now seeing the beginning of the Terminal Lines . Yes, I am aware of Armbian Config - once you get it. and that it only works if you establish a root login. Which is a bitch to do when you can't see the text at the beginning of the prompt. OK, hope you don't think I am totally ignorant on this, -- even if I am. Now: PLEASE, PLEASE, PLEASE - the default setting should be such that the display - on initial boot, MUST be changed so that ALL of the HDMI output is displayed on a typical monitor (which does NOT have overscan setting options) Thank you for your understanding. and hopefully help - I suggest you take a lesson from Raspberry Pi Thanks again. Richard Link to comment Share on other sites More sharing options...
Tido Posted March 15, 2018 Share Posted March 15, 2018 Well Richard, I take your complaint with a grain of salt. You know a lot, but still to little to help yourself to login via SSH. Linux is not Windows Armbian is not Raspbian ;-) and will NEVER be. Study the first lines carfully: https://docs.armbian.com/User-Guide_Getting-Started/#how-to-login Link to comment Share on other sites More sharing options...
richard1937 Posted March 16, 2018 Share Posted March 16, 2018 I know, and use SSH to go into a server for standard work. I use putty and have for years to go into www.itu-int.us. My server for this is Centos. It is an interface for a server in Geneva. There is a bit of Chicken/Egg issue for me at the moment. I am on the road, at daughters beach place, for several weeks (fixing some things for her) so limited resources for MY project. No Ethernet access, LePotato doesn't have Wifi, Panda doesn't work. etc. etc. I wish I had brought along several other items, but I didn't . About asking, some folks are too proud to ask anything, not me, I read/google etc. try "thoughts" that I see. MOST post about this seem to be over a year old - some progress must have been made - etc. So I ask. If you want to help - I would appreciate that. If NOT you are of course welcome to ignore me. I picked trying Armbian as it seemed to support and advocate - armbian-config . I am working with Armbian 5.8 Stable This seemed like a great way to iniially setup etc. basic things. Unfortunately - when you use it to edit HDMI resolution, Mouse size etc etc. nothing changes. Even if directly logged in as root! Last night I found a small TV at Kmart for $88. that I could set to accommodate the overscan issue. The TV solves this for the moment but it otherwise really sucks! I would be NICE to change the mouse icon size. ( I have don't this on RPi, OrangePi, TinkerPi etc. but those methods don't work here. - and Armbian doesn't change ti either, It seems size is set at boot, and Armbian-config does not change the file where it is set, and that is actually viewed to ultimately set the size. _ I think this many be true for the overscan issuse as well.? Actually, More important - any ideas on getting Panda WiFi dongle working? Then I can do update and upgrade etc. and then install other needed items. Thanks, for any help. Richard Link to comment Share on other sites More sharing options...
Da Xue Posted March 17, 2018 Share Posted March 17, 2018 On 3/16/2018 at 11:47 AM, richard1937 said: I know, and use SSH to go into a server for standard work. I use putty and have for years to go into www.itu-int.us. My server for this is Centos. It is an interface for a server in Geneva. There is a bit of Chicken/Egg issue for me at the moment. I am on the road, at daughters beach place, for several weeks (fixing some things for her) so limited resources for MY project. No Ethernet access, LePotato doesn't have Wifi, Panda doesn't work. etc. etc. I wish I had brought along several other items, but I didn't . About asking, some folks are too proud to ask anything, not me, I read/google etc. try "thoughts" that I see. MOST post about this seem to be over a year old - some progress must have been made - etc. So I ask. If you want to help - I would appreciate that. If NOT you are of course welcome to ignore me. I picked trying Armbian as it seemed to support and advocate - armbian-config . I am working with Armbian 5.8 Stable This seemed like a great way to iniially setup etc. basic things. Unfortunately - when you use it to edit HDMI resolution, Mouse size etc etc. nothing changes. Even if directly logged in as root! Last night I found a small TV at Kmart for $88. that I could set to accommodate the overscan issue. The TV solves this for the moment but it otherwise really sucks! I would be NICE to change the mouse icon size. ( I have don't this on RPi, OrangePi, TinkerPi etc. but those methods don't work here. - and Armbian doesn't change ti either, It seems size is set at boot, and Armbian-config does not change the file where it is set, and that is actually viewed to ultimately set the size. _ I think this many be true for the overscan issuse as well.? Actually, More important - any ideas on getting Panda WiFi dongle working? Then I can do update and upgrade etc. and then install other needed items. Thanks, for any help. Richard Run `lsusb` so we know what chipset is in the Panda wifi device. It's probably a kernel module issue. Mainline linux display mode code was just merged into 4.17. It will take a while for it to land in Armbian. Link to comment Share on other sites More sharing options...
TonyMac32 Posted March 17, 2018 Share Posted March 17, 2018 1 hour ago, Da Xue said: Mainline linux display mode code was just merged into 4.17. It will take a while for it to land in Armbian. My intention, and I think Igor agrees, is to go LTS kernel to LTS kernel. It is possible to build a current "bleeding edge" mainline if you have the means to do it yourself, the "Dev branch is current. @Igor, the vendor kernel (vendor being Libre Computer) in this case is 4.14, should we make that "default" for this board? Especially since, IMHO, @balbes150 has provided the definitive guide and images to run the 3.14 on anything with an s905(x) adequately using his fork. "Next" then could be a current mainline image that we're comfortable with. Link to comment Share on other sites More sharing options...
Igor Posted March 17, 2018 Share Posted March 17, 2018 1 minute ago, TonyMac32 said: should we make that "default" for this board? ... and K2, while Odroid C2 has it's own defaults anyway. Than Odroid C2 4.14.y "next" goes to meson64-default. Sleepover, then just do it? Link to comment Share on other sites More sharing options...
TonyMac32 Posted March 17, 2018 Share Posted March 17, 2018 1 minute ago, Igor said: Sleepover, then just do it? I think so. Maybe see if any of the usual suspects have feedback first. Link to comment Share on other sites More sharing options...
TonyMac32 Posted March 19, 2018 Share Posted March 19, 2018 @Igor Quick concern I thought of, people running "Next" currently would probably get automatically (and possibly unwantedly) updated to 4.16. Link to comment Share on other sites More sharing options...
Igor Posted March 19, 2018 Share Posted March 19, 2018 6 hours ago, TonyMac32 said: @Igor Quick concern I thought of, people running "Next" currently would probably get automatically (and possibly unwantedly) updated to 4.16. Then better just leave as is for next couple of months. Another alternative is to move NEXT to default and operate only default and dev for some time? Link to comment Share on other sites More sharing options...
TonyMac32 Posted March 19, 2018 Share Posted March 19, 2018 I could put this up for discussion on the Facebook group and see. I know we don't want to interrupt the stream, but we're still getting people showing up with 4.13 kernels, so... Let's wait for 4.16 to be released, see how stable the result is and go from there. 1 Link to comment Share on other sites More sharing options...
tkaiser Posted May 4, 2018 Share Posted May 4, 2018 On 27.9.2017 at 8:18 AM, Neil Armstrong said: Mainline Linux has support for the SCPI Temperature Sensor, please check in /sys/class/hwmon/hwmon0/temp1_input @TonyMac32 so does reading out the temperature with e.g. armbianmonitor works now after this commit? Link to comment Share on other sites More sharing options...
TonyMac32 Posted May 4, 2018 Share Posted May 4, 2018 16 hours ago, tkaiser said: @TonyMac32 so does reading out the temperature with e.g. armbianmonitor works now after this commit? Let me check later, we had a windstorm and I'm running on generator power. :-/ Link to comment Share on other sites More sharing options...
TonyMac32 Posted May 29, 2018 Share Posted May 29, 2018 @tkaiser sorry about the delay, I lost track of this with all the other stuff going on. No, I'm not getting anything on a new build. root@lepotato:~# cat /sys/class/hwmon/hwmon0/temp1_input 28000 works, but the soctemp entry in datasources does not exist. This one was built off of the master branch with the recent syncs, armhwinfo looks to have the above commit in it. Link to comment Share on other sites More sharing options...
Recommended Posts